--- /dev/null
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2022 - 2023 PHYTEC Messtechnik GmbH
+ * Author: Wadim Egorov <w.egorov@phytec.de>
+ *
+ * Product homepage:
+ * https://www.phytec.com/product/phycore-am62x
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/net/ti-dp83867.h>
+
+/ {
+ model = "PHYTEC phyCORE-AM62x";
+ compatible = "phytec,am62-phycore-som", "ti,am625";
+
+ aliases {
+ ethernet0 = &cpsw_port1;
+ gpio0 = &main_gpio0;
+ gpio1 = &main_gpio1;
+ i2c0 = &main_i2c0;
+ mmc0 = &sdhci0;
+ rtc0 = &i2c_som_rtc;
+ rtc1 = &wkup_rtc0;
+ spi0 = &ospi0;
+ };
+
+ memory@80000000 {
+ device_type = "memory";
+ reg = <0x00000000 0x80000000 0x00000000 0x80000000>;
+ };
+
+ reserved_memory: reserved-memory {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ ramoops@9ca00000 {
+ compatible = "ramoops";
+ reg = <0x00 0x9ca00000 0x00 0x00100000>;
+ record-size = <0x8000>;
+ console-size = <0x8000>;
+ ftrace-size = <0x00>;
+ pmsg-size = <0x8000>;
+ };
+
+ secure_tfa_ddr: tfa@9e780000 {
+ reg = <0x00 0x9e780000 0x00 0x80000>;
+ alignment = <0x1000>;
+ no-map;
+ };
+
+ secure_ddr: optee@9e800000 {
+ reg = <0x00 0x9e800000 0x00 0x01800000>; /* for OP-TEE */
+ alignment = <0x1000>;
+ no-map;
+ };
+
+ wkup_r5fss0_core0_dma_memory_region: r5f-dma-memory@9db00000 {
+ compatible = "shared-dma-pool";
+ reg = <0x00 0x9db00000 0x00 0x00c00000>;
+ no-map;
+ };
+ };
+
+ vcc_5v0_som: regulator-vcc-5v0-som {
+ compatible = "regulator-fixed";
+ regulator-name = "VCC_5V0_SOM";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ vdd_1v8: regulator-vdd-1v8 {
+ compatible = "regulator-fixed";
+ regulator-name = "VDD_1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ vin-supply = <&vcc_5v0_som>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&leds_pins_default>;
+
+ led-0 {
+ color = <LED_COLOR_ID_GREEN>;
+ gpios = <&main_gpio0 13 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ function = LED_FUNCTION_HEARTBEAT;
+ };
+ };
+};
+
+&main_pmx0 {
+ leds_pins_default: leds-pins-default {
+ pinctrl-single,pins = <
+ AM62X_IOPAD(0x034, PIN_OUTPUT, 7) /* (H21) OSPI0_CSN2.GPIO0_13 */
+ >;
+ };
+
+ main_i2c0_pins_default: main-i2c0-pins-default {
+ pinctrl-single,pins = <
+ AM62X_IOPAD(0x1e0, PIN_INPUT_PULLUP, 0) /* (B16) I2C0_SCL */
+ AM62X_IOPAD(0x1e4, PIN_INPUT_PULLUP, 0) /* (A16) I2C0_SDA */
+ >;
+ };
+
+ main_mdio1_pins_default: main-mdio1-pins-default {
+ pinctrl-single,pins = <
+ AM62X_IOPAD(0x160, PIN_OUTPUT, 0) /* (AD24) MDIO0_MDC */
+ AM62X_IOPAD(0x15c, PIN_INPUT, 0) /* (AB22) MDIO0_MDIO */
+ >;
+ };
+
+ main_mmc0_pins_default: main-mmc0-pins-default {
+ pinctrl-single,pins = <
+ AM62X_IOPAD(0x220, PIN_INPUT_PULLUP, 0) /* (Y3) MMC0_CMD */
+ AM62X_IOPAD(0x218, PIN_INPUT_PULLDOWN, 0) /* (AB1) MMC0_CLK */
+ AM62X_IOPAD(0x214, PIN_INPUT_PULLUP, 0) /* (AA2) MMC0_DAT0 */
+ AM62X_IOPAD(0x210, PIN_INPUT_PULLUP, 0) /* (AA1) MMC0_DAT1 */
+ AM62X_IOPAD(0x20c, PIN_INPUT_PULLUP, 0) /* (AA3) MMC0_DAT2 */
+ AM62X_IOPAD(0x208, PIN_INPUT_PULLUP, 0) /* (Y4) MMC0_DAT3 */
+ AM62X_IOPAD(0x204, PIN_INPUT_PULLUP, 0) /* (AB2) MMC0_DAT4 */
+ AM62X_IOPAD(0x200, PIN_INPUT_PULLUP, 0) /* (AC1) MMC0_DAT5 */
+ AM62X_IOPAD(0x1fc, PIN_INPUT_PULLUP, 0) /* (AD2) MMC0_DAT6 */
+ AM62X_IOPAD(0x1f8, PIN_INPUT_PULLUP, 0) /* (AC2) MMC0_DAT7 */
+ >;
+ };
+
+ main_rgmii1_pins_default: main-rgmii1-pins-default {
+ pinctrl-single,pins = <
+ AM62X_IOPAD(0x14c, PIN_INPUT, 0) /* (AB17) RGMII1_RD0 */
+ AM62X_IOPAD(0x150, PIN_INPUT, 0) /* (AC17) RGMII1_RD1 */
+ AM62X_IOPAD(0x154, PIN_INPUT, 0) /* (AB16) RGMII1_RD2 */
+ AM62X_IOPAD(0x158, PIN_INPUT, 0) /* (AA15) RGMII1_RD3 */
+ AM62X_IOPAD(0x148, PIN_INPUT, 0) /* (AD17) RGMII1_RXC */
+ AM62X_IOPAD(0x144, PIN_INPUT, 0) /* (AE17) RGMII1_RX_CTL */
+ AM62X_IOPAD(0x134, PIN_OUTPUT, 0) /* (AE20) RGMII1_TD0 */
+ AM62X_IOPAD(0x138, PIN_OUTPUT, 0) /* (AD20) RGMII1_TD1 */
+ AM62X_IOPAD(0x13c, PIN_OUTPUT, 0) /* (AE18) RGMII1_TD2 */
+ AM62X_IOPAD(0x140, PIN_OUTPUT, 0) /* (AD18) RGMII1_TD3 */
+ AM62X_IOPAD(0x130, PIN_OUTPUT, 0) /* (AE19) RGMII1_TXC */
+ AM62X_IOPAD(0x12c, PIN_OUTPUT, 0) /* (AD19) RGMII1_TX_CTL */
+ >;
+ };
+
+ ospi0_pins_default: ospi0-pins-default {
+ pinctrl-single,pins = <
+ AM62X_IOPAD(0x000, PIN_OUTPUT, 0) /* (H24) OSPI0_CLK */
+ AM62X_IOPAD(0x02c, PIN_OUTPUT, 0) /* (F23) OSPI0_CSn0 */
+ AM62X_IOPAD(0x00c, PIN_INPUT, 0) /* (E25) OSPI0_D0 */
+ AM62X_IOPAD(0x010, PIN_INPUT, 0) /* (G24) OSPI0_D1 */
+ AM62X_IOPAD(0x014, PIN_INPUT, 0) /* (F25) OSPI0_D2 */
+ AM62X_IOPAD(0x018, PIN_INPUT, 0) /* (F24) OSPI0_D3 */
+ AM62X_IOPAD(0x01c, PIN_INPUT, 0) /* (J23) OSPI0_D4 */
+ AM62X_IOPAD(0x020, PIN_INPUT, 0) /* (J25) OSPI0_D5 */
+ AM62X_IOPAD(0x024, PIN_INPUT, 0) /* (H25) OSPI0_D6 */
+ AM62X_IOPAD(0x028, PIN_INPUT, 0) /* (J22) OSPI0_D7 */
+ AM62X_IOPAD(0x008, PIN_INPUT, 0) /* (J24) OSPI0_DQS */
+ >;
+ };
+
+ pmic_irq_pins_default: pmic-irq-pins-default {
+ pinctrl-single,pins = <
+ AM62X_IOPAD(0x01f4, PIN_INPUT, 0) /* (D16) EXTINTn */
+ >;
+ };
+};
+
+&cpsw3g {
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_rgmii1_pins_default>;
+};
+
+&cpsw_port1 {
+ phy-mode = "rgmii-rxid";
+ phy-handle = <&cpsw3g_phy1>;
+};
+
+&cpsw3g_mdio {
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_mdio1_pins_default>;
+ status = "okay";
+
+ cpsw3g_phy1: ethernet-phy@1 {
+ compatible = "ethernet-phy-id2000.a231", "ethernet-phy-ieee802.3-c22";
+ reg = <1>;
+ ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
+ ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
+ };
+};
+
+&main_i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_i2c0_pins_default>;
+ clock-frequency = <400000>;
+ status = "okay";
+
+ pmic@30 {
+ compatible = "ti,tps65219";
+ reg = <0x30>;
+ buck1-supply = <&vcc_5v0_som>;
+ buck2-supply = <&vcc_5v0_som>;
+ buck3-supply = <&vcc_5v0_som>;
+ ldo1-supply = <&vdd_3v3>;
+ ldo2-supply = <&vdd_1v8>;
+ ldo3-supply = <&vcc_5v0_som>;
+ ldo4-supply = <&vcc_5v0_som>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pmic_irq_pins_default>;
+ interrupt-parent = <&gic500>;
+ interrupts = <GIC_SPI 224 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-controller;
+ #interrupt-cells = <1>;
+
+ ti,power-button;
+ system-power-controller;
+
+ regulators {
+ vdd_core: buck1 {
+ regulator-name = "VDD_CORE";
+ regulator-min-microvolt = <750000>;
+ regulator-max-microvolt = <750000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vdd_3v3: buck2 {
+ regulator-name = "VDD_3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vdd_ddr4: buck3 {
+ regulator-name = "VDD_DDR4";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vddshv5_sdio: ldo1 {
+ regulator-name = "VDDSHV5_SDIO";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-allow-bypass;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vddr_core: ldo2 {
+ regulator-name = "VDDR_CORE";
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <850000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vdda_1v8: ldo3 {
+ regulator-name = "VDDA_1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vdd_2v5: ldo4 {
+ regulator-name = "VDD_2V5";
+ regulator-min-microvolt = <2500000>;
+ regulator-max-microvolt = <2500000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+ };
+ };
+
+ eeprom@50 {
+ compatible = "atmel,24c32";
+ pagesize = <32>;
+ reg = <0x50>;
+ };
+
+ i2c_som_rtc: rtc@52 {
+ compatible = "microcrystal,rv3028";
+ reg = <0x52>;
+ };
+};
+
+&ospi0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&ospi0_pins_default>;
+ status = "okay";
+
+ serial_flash: flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0x0>;
+ spi-tx-bus-width = <8>;
+ spi-rx-bus-width = <8>;
+ spi-max-frequency = <25000000>;
+ cdns,tshsl-ns = <60>;
+ cdns,tsd2d-ns = <60>;
+ cdns,tchsh-ns = <60>;
+ cdns,tslch-ns = <60>;
+ cdns,read-delay = <0>;
+ };
+};
+
+&sdhci0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_mmc0_pins_default>;
+ ti,driver-strength-ohm = <50>;
+ disable-wp;
+ non-removable;
+ status = "okay";
+};
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2022 - 2023 PHYTEC Messtechnik GmbH
+ * Author: Wadim Egorov <w.egorov@phytec.de>
+ *
+ * Product homepage:
+ * https://www.phytec.com/product/phyboard-am62x
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/net/ti-dp83867.h>
+#include "k3-am625.dtsi"
+#include "k3-am62-phycore-som.dtsi"
+
+/ {
+ compatible = "phytec,am625-phyboard-lyra-rdk",
+ "phytec,am62-phycore-som", "ti,am625";
+ model = "PHYTEC phyBOARD-Lyra AM625";
+
+ aliases {
+ serial2 = &main_uart0;
+ serial3 = &main_uart1;
+ mmc1 = &sdhci1;
+ usb0 = &usb0;
+ usb1 = &usb1;
+ ethernet1 = &cpsw_port2;
+ };
+
+ can_tc1: can-phy0 {
+ compatible = "ti,tcan1042";
+ #phy-cells = <0>;
+ max-bitrate = <5000000>;
+ standby-gpios = <&gpio_exp 1 GPIO_ACTIVE_HIGH>;
+ };
+
+ keys {
+ compatible = "gpio-keys";
+ autorepeat;
+ pinctrl-names = "default";
+ pinctrl-0 = <&gpio_keys_pins_default>;
+
+ key-home {
+ label = "home";
+ linux,code = <KEY_HOME>;
+ gpios = <&main_gpio1 23 GPIO_ACTIVE_HIGH>;
+ };
+
+ key-menu {
+ label = "menu";
+ linux,code = <KEY_MENU>;
+ gpios = <&gpio_exp 4 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&leds_pins_default>, <&user_leds_pins_default>;
+
+ led-1 {
+ gpios = <&main_gpio0 32 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "mmc0";
+ };
+
+ led-2 {
+ gpios = <&gpio_exp 2 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "mmc1";
+ };
+ };
+
+ vcc_3v3_mmc: regulator-vcc-3v3-mmc {
+ compatible = "regulator-fixed";
+ regulator-name = "VCC_3V3_MMC";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+};
+
+&main_pmx0 {
+ gpio_keys_pins_default: gpio-keys-pins-default {
+ pinctrl-single,pins = <
+ AM62X_IOPAD(0x1d4, PIN_INPUT, 7) /* (B15) UART0_RTSn.GPIO1_23 */
+ >;
+ };
+
+ gpio_exp_int_pins_default: gpio-exp-int-pins-default {
+ pinctrl-single,pins = <
+ AM62X_IOPAD(0x244, PIN_INPUT, 7) /* (C17) MMC1_SDWP.GPIO1_49 */
+ >;
+ };
+
+ main_i2c1_pins_default: main-i2c1-pins-default {
+ pinctrl-single,pins = <
+ AM62X_IOPAD(0x1e8, PIN_INPUT_PULLUP, 0) /* (B17) I2C1_SCL */
+ AM62X_IOPAD(0x1ec, PIN_INPUT_PULLUP, 0) /* (A17) I2C1_SDA */
+ >;
+ };
+
+ main_mcan0_pins_default: main-mcan0-pins-default {
+ pinctrl-single,pins = <
+ AM62X_IOPAD(0x1dc, PIN_INPUT, 0) /* (E15) MCAN0_RX */
+ AM62X_IOPAD(0x1d8, PIN_OUTPUT, 0) /* (C15) MCAN0_TX */
+ >;
+ };
+
+ main_mmc1_pins_default: main-mmc1-pins-default {
+ pinctrl-single,pins = <
+ AM62X_IOPAD(0x23c, PIN_INPUT_PULLUP, 0) /* (A21) MMC1_CMD */
+ AM62X_IOPAD(0x234, PIN_INPUT_PULLDOWN, 0) /* (B22) MMC1_CLK */
+ AM62X_IOPAD(0x230, PIN_INPUT_PULLUP, 0) /* (A22) MMC1_DAT0 */
+ AM62X_IOPAD(0x22c, PIN_INPUT_PULLUP, 0) /* (B21) MMC1_DAT1 */
+ AM62X_IOPAD(0x228, PIN_INPUT_PULLUP, 0) /* (C21) MMC1_DAT2 */
+ AM62X_IOPAD(0x224, PIN_INPUT_PULLUP, 0) /* (D22) MMC1_DAT3 */
+ AM62X_IOPAD(0x240, PIN_INPUT_PULLUP, 0) /* (D17) MMC1_SDCD */
+ >;
+ };
+
+ main_rgmii2_pins_default: main-rgmii2-pins-default {
+ pinctrl-single,pins = <
+ AM62X_IOPAD(0x184, PIN_INPUT, 0) /* (AE23) RGMII2_RD0 */
+ AM62X_IOPAD(0x188, PIN_INPUT, 0) /* (AB20) RGMII2_RD1 */
+ AM62X_IOPAD(0x18c, PIN_INPUT, 0) /* (AC21) RGMII2_RD2 */
+ AM62X_IOPAD(0x190, PIN_INPUT, 0) /* (AE22) RGMII2_RD3 */
+ AM62X_IOPAD(0x180, PIN_INPUT, 0) /* (AD23) RGMII2_RXC */
+ AM62X_IOPAD(0x17c, PIN_INPUT, 0) /* (AD22) RGMII2_RX_CTL */
+ AM62X_IOPAD(0x16c, PIN_OUTPUT, 0) /* (Y18) RGMII2_TD0 */
+ AM62X_IOPAD(0x170, PIN_OUTPUT, 0) /* (AA18) RGMII2_TD1 */
+ AM62X_IOPAD(0x174, PIN_OUTPUT, 0) /* (AD21) RGMII2_TD2 */
+ AM62X_IOPAD(0x178, PIN_OUTPUT, 0) /* (AC20) RGMII2_TD3 */
+ AM62X_IOPAD(0x168, PIN_OUTPUT, 0) /* (AE21) RGMII2_TXC */
+ AM62X_IOPAD(0x164, PIN_OUTPUT, 0) /* (AA19) RGMII2_TX_CTL */
+ >;
+ };
+
+ main_uart0_pins_default: main-uart0-pins-default {
+ pinctrl-single,pins = <
+ AM62X_IOPAD(0x1c8, PIN_INPUT, 0) /* (D14) UART0_RXD */
+ AM62X_IOPAD(0x1cc, PIN_OUTPUT, 0) /* (E14) UART0_TXD */
+ >;
+ };
+
+ main_uart1_pins_default: main-uart1-pins-default {
+ pinctrl-single,pins = <
+ AM62X_IOPAD(0x194, PIN_INPUT, 2) /* (B19) MCASP0_AXR3.UART1_CTSn */
+ AM62X_IOPAD(0x198, PIN_OUTPUT, 2) /* (A19) MCASP0_AXR2.UART1_RTSn */
+ AM62X_IOPAD(0x1ac, PIN_INPUT, 2) /* (E19) MCASP0_AFSR.UART1_RXD */
+ AM62X_IOPAD(0x1b0, PIN_OUTPUT, 2) /* (A20) MCASP0_ACLKR.UART1_TXD */
+ >;
+ };
+
+ main_usb1_pins_default: main-usb1-pins-default {
+ pinctrl-single,pins = <
+ AM62X_IOPAD(0x258, PIN_OUTPUT, 0) /* (F18) USB1_DRVVBUS */
+ >;
+ };
+
+ user_leds_pins_default: user-leds-pins-default {
+ pinctrl-single,pins = <
+ AM62X_IOPAD(0x084, PIN_OUTPUT, 7) /* (L23) GPMC0_ADVn_ALE.GPIO0_32 */
+ >;
+ };
+};
+
+&cpsw3g {
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_rgmii1_pins_default>, <&main_rgmii2_pins_default>;
+};
+
+&cpsw_port2 {
+ phy-mode = "rgmii-rxid";
+ phy-handle = <&cpsw3g_phy3>;
+};
+
+&cpsw3g_mdio {
+ cpsw3g_phy3: ethernet-phy@3 {
+ compatible = "ethernet-phy-id2000.a231", "ethernet-phy-ieee802.3-c22";
+ reg = <3>;
+ ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
+ ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
+ };
+};
+
+&main_i2c1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_i2c1_pins_default>;
+ clock-frequency = <400000>;
+ status = "okay";
+
+ gpio_exp: gpio-expander@21 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&gpio_exp_int_pins_default>;
+ compatible = "nxp,pcf8574";
+ reg = <0x21>;
+ interrupt-parent = <&main_gpio1>;
+ interrupts = <49 0>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ gpio-line-names = "GPIO0_HDMI_RST", "GPIO1_CAN0_nEN",
+ "GPIO2_LED2", "GPIO3_LVDS_GPIO",
+ "GPIO4_BUT2", "GPIO5_LVDS_BKLT_EN",
+ "GPIO6_ETH1_USER_RESET", "GPIO7_AUDIO_USER_RESET";
+ };
+
+ eeprom@51 {
+ compatible = "atmel,24c02";
+ pagesize = <16>;
+ reg = <0x51>;
+ };
+};
+
+&main_mcan0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_mcan0_pins_default>;
+ phys = <&can_tc1>;
+ status = "okay";
+};
+
+&main_uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_uart0_pins_default>;
+ status = "okay";
+};
+
+&main_uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_uart1_pins_default>;
+ /* Main UART1 may be used by TIFS firmware */
+ status = "okay";
+};
+
+&sdhci1 {
+ vmmc-supply = <&vcc_3v3_mmc>;
+ vqmmc-supply = <&vddshv5_sdio>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_mmc1_pins_default>;
+ ti,driver-strength-ohm = <50>;
+ disable-wp;
+ no-1-8-v;
+ status = "okay";
+};
+
+&usbss0 {
+ ti,vbus-divider;
+ status = "okay";
+};
+
+&usbss1 {
+ ti,vbus-divider;
+ status = "okay";
+};
+
+&usb0 {
+ dr_mode = "peripheral";
+};
+
+&usb1 {
+ dr_mode = "host";
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_usb1_pins_default>;
+};
projects / platform / kernel / linux-rpi.git / commitdiff