development platform that supports the QorIQ LS2080A
Layerscape Architecture processor.
+config TARGET_LS2081ARDB
+ bool "Support ls2081ardb"
+ select ARCH_LS2080A
+ select ARM64
+ select ARMV8_MULTIENTRY
+ select BOARD_LATE_INIT
+ select SUPPORT_SPL
+ select ARCH_MISC_INIT
+ help
+ Support for Freescale LS2081ARDB platform.
+ The LS2081A Reference design board (RDB) is a high-performance
+ development platform that supports the QorIQ LS2081A/LS2041A
+ Layerscape Architecture processor.
+
config TARGET_HIKEY
bool "Support HiKey 96boards Consumer Edition Platform"
select ARM64
!TARGET_LS1012ARDB && !TARGET_LS1012AFRDM && \
!TARGET_LS1043ARDB && !TARGET_LS1043AQDS && \
!TARGET_LS1046ARDB && !TARGET_LS1046AQDS && \
+ !TARGET_LS2081ARDB && \
!ARCH_UNIPHIER && !ARCH_SNAPDRAGON && !TARGET_S32V234EVB
help
Most armv8 systems have PSCI support enabled in EL3, either through
ls1021a-iot-duart.dtb
dtb-$(CONFIG_FSL_LSCH3) += fsl-ls2080a-qds.dtb \
fsl-ls2080a-rdb.dtb \
+ fsl-ls2081a-rdb.dtb \
fsl-ls2088a-rdb-qspi.dtb
dtb-$(CONFIG_FSL_LSCH2) += fsl-ls1043a-qds-duart.dtb \
fsl-ls1043a-qds-lpuart.dtb \
--- /dev/null
+/*
+ * NXP LS2081A RDB board device tree source for QSPI-boot
+ *
+ * Author: Priyanka Jain <priyanka.jain@nxp.com>
+ *
+ * Copyright 2017 NXP
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+/dts-v1/;
+
+#include "fsl-ls2080a.dtsi"
+
+/ {
+ model = "Freescale Layerscape 2081a RDB Board";
+ compatible = "fsl,ls2081a-rdb", "fsl,ls2080a";
+
+ aliases {
+ spi0 = &qspi;
+ spi1 = &dspi;
+ };
+};
+
+&dspi {
+ bus-num = <0>;
+ status = "okay";
+
+ dflash0: n25q512a {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "spi-flash";
+ spi-max-frequency = <3000000>;
+ spi-cpol;
+ spi-cpha;
+ reg = <0>;
+ };
+};
+
+&qspi {
+ bus-num = <0>;
+ status = "okay";
+
+ qflash0: n25q512a@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "spi-flash";
+ spi-max-frequency = <50000000>;
+ reg = <0>;
+ };
+
+ qflash1: n25q512a@1 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "spi-flash";
+ spi-max-frequency = <50000000>;
+ reg = <1>;
+ };
+};
source "board/freescale/common/Kconfig"
endif
+
+if TARGET_LS2081ARDB
+
+config SYS_BOARD
+ default "ls2080ardb"
+
+config SYS_VENDOR
+ default "freescale"
+
+config SYS_SOC
+ default "fsl-layerscape"
+
+config SYS_CONFIG_NAME
+ default "ls2080ardb"
+
+source "board/freescale/common/Kconfig"
+
+endif
S: Maintained
F: configs/ls2088ardb_qspi_defconfig
+LS2081ARDB BOARD
+M: Priyanka Jain <priyanka.jain@nxp.com>
+S: Maintained
+F: configs/ls2081ardb_defconfig
+
LS2080A_SECURE_BOOT BOARD
M: Saksham Jain <saksham.jain@nxp.freescale.com>
S: Maintained
evaluation, and development platform that supports the QorIQ LS2080A, LS2088A
Layerscape Architecture processor.
-LS2080A, LS2088A SoC Overview
---------------------
+The LS2081A Reference Design (RDB) is a high-performance computing,
+evaluation, and development platform that supports the QorIQ LS2081A
+Layerscape Architecture processor.More details in below sections
+
+LS2080A, LS2088A, LS2081A SoC Overview
+--------------------------------------
Please refer arch/arm/cpu/armv8/fsl-layerscape/doc/README.soc for LS2080A,
-LS2088A SoC overview.
+LS2081A, LS2088A SoC overview.
LS2080ARDB board Overview
-----------------------
- UART
- ARM JTAG support
+ LS2081ARDB board Overview
+ -------------------------
+ LS2081ARDB board is similar to LS2080ARDB board
+ with few differences like
+ - Hosts LS2081A SoC
+ - Default boot source is QSPI-boot
+ - Does not have IFC interface
+ - RTC and QSPI flash devices are different
+ - Provides QIXIS access via I2C
+
Memory map from core's view
----------------------------
0x00_0000_0000 .. 0x00_000F_FFFF Boot Rom
cpu_name(buf);
printf("Board: %s-RDB, ", buf);
+#ifdef CONFIG_TARGET_LS2081ARDB
+#ifdef CONFIG_FSL_QIXIS
+ sw = QIXIS_READ(arch);
+ printf("Board Arch: V%d, ", sw >> 4);
+ printf("Board version: %c, ", (sw & 0xf) + 'A');
+
+ sw = QIXIS_READ(brdcfg[0]);
+ sw = (sw & QIXIS_QMAP_MASK) >> QIXIS_QMAP_SHIFT;
+ switch (sw) {
+ case 0:
+ puts("boot from QSPI DEV#0\n");
+ puts("QSPI_CSA_1 mapped to QSPI DEV#1\n");
+ break;
+ case 1:
+ puts("boot from QSPI DEV#1\n");
+ puts("QSPI_CSA_1 mapped to QSPI DEV#0\n");
+ break;
+ case 2:
+ puts("boot from QSPI EMU\n");
+ puts("QSPI_CSA_1 mapped to QSPI DEV#0\n");
+ break;
+ case 3:
+ puts("boot from QSPI EMU\n");
+ puts("QSPI_CSA_1 mapped to QSPI DEV#1\n");
+ break;
+ case 4:
+ puts("boot from QSPI DEV#0\n");
+ puts("QSPI_CSA_1 mapped to QSPI EMU\n");
+ break;
+ default:
+ printf("invalid setting of SW%u\n", sw);
+ break;
+ }
+#endif
+ puts("SERDES1 Reference : ");
+ printf("Clock1 = 100MHz ");
+ printf("Clock2 = 161.13MHz");
+#else
#ifdef CONFIG_FSL_QIXIS
sw = QIXIS_READ(arch);
printf("Board Arch: V%d, ", sw >> 4);
puts("SERDES1 Reference : ");
printf("Clock1 = 156.25MHz ");
printf("Clock2 = 156.25MHz");
+#endif
puts("\nSERDES2 Reference : ");
printf("Clock1 = 100MHz ");
int board_early_init_f(void)
{
+#ifdef CONFIG_SYS_I2C_EARLY_INIT
+ i2c_early_init_f();
+#endif
fsl_lsch3_early_init_f();
return 0;
}
int misc_init_r(void)
{
#ifdef CONFIG_FSL_QIXIS
+ /*
+ * LS2081ARDB has smart voltage translator which needs
+ * to be programmed as below
+ */
+#ifndef CONFIG_TARGET_LS2081ARDB
u8 sw;
sw = QIXIS_READ(arch);
* by setting GPIO4_10 output to zero
*/
if ((sw & 0xf) == 0x5) {
+#endif
out_le32(GPIO4_GPDIR_ADDR, (1 << 21 |
in_le32(GPIO4_GPDIR_ADDR)));
out_le32(GPIO4_GPDAT_ADDR, (~(1 << 21) &
in_le32(GPIO4_GPDAT_ADDR)));
+#ifndef CONFIG_TARGET_LS2081ARDB
}
#endif
+#endif
if (hwconfig("sdhc"))
config_board_mux(MUX_TYPE_SDHC);
unsigned int slot,
unsigned int *addr)
{
+#ifndef CONFIG_TARGET_LS2081ARDB
#ifdef CONFIG_FSL_QIXIS
u8 sw;
*addr = SPD_EEPROM_ADDRESS3;
}
#endif
+#endif
}
--- /dev/null
+CONFIG_ARM=y
+CONFIG_TARGET_LS2081ARDB=y
+CONFIG_FSL_LS_PPA=y
+CONFIG_QSPI_AHB_INIT=y
+CONFIG_DEFAULT_DEVICE_TREE="fsl-ls2081a-rdb"
+# CONFIG_SYS_MALLOC_F is not set
+CONFIG_FIT_VERBOSE=y
+CONFIG_OF_BOARD_SETUP=y
+CONFIG_OF_STDOUT_VIA_ALIAS=y
+CONFIG_QSPI_BOOT=y
+CONFIG_BOOTDELAY=10
+CONFIG_CMD_GREPENV=y
+# CONFIG_CMD_IMLS is not set
+CONFIG_CMD_GPT=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_SF=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_DHCP=y
+CONFIG_CMD_MII=y
+CONFIG_CMD_PING=y
+CONFIG_CMD_CACHE=y
+CONFIG_CMD_EXT2=y
+CONFIG_CMD_FAT=y
+CONFIG_OF_CONTROL=y
+CONFIG_NET_RANDOM_ETHADDR=y
+CONFIG_DM=y
+CONFIG_FSL_CAAM=y
+CONFIG_DM_SPI_FLASH=y
+CONFIG_NETDEVICES=y
+CONFIG_E1000=y
+CONFIG_PCI=y
+CONFIG_DM_PCI=y
+CONFIG_DM_PCI_COMPAT=y
+CONFIG_PCIE_LAYERSCAPE=y
+CONFIG_SYS_NS16550=y
+CONFIG_DM_SPI=y
+CONFIG_FSL_QSPI=y
+CONFIG_FSL_DSPI=y
+CONFIG_CMD_USB=y
+# CONFIG_CMD_SETEXPR is not set
+CONFIG_USB=y
+CONFIG_DM_USB=y
+CONFIG_USB_XHCI_HCD=y
+CONFIG_USB_XHCI_DWC3=y
+CONFIG_USB_STORAGE=y
+CONFIG_EFI_LOADER_BOUNCE_BUFFER=y
static int erratum_a008751(void)
{
-#if defined(CONFIG_TARGET_LS2080AQDS) || defined(CONFIG_TARGET_LS2080ARDB)
+#if defined(CONFIG_TARGET_LS2080AQDS) || defined(CONFIG_TARGET_LS2080ARDB) ||\
+ defined(CONFIG_TARGET_LS2080AQDS)
u32 __iomem *scfg = (u32 __iomem *)SCFG_BASE;
writel(SCFG_USB3PRM1CR_INIT, scfg + SCFG_USB3PRM1CR / 4);
return 0;
#define CONFIG_CONS_INDEX 2
#ifdef CONFIG_FSL_QSPI
+#ifdef CONFIG_TARGET_LS2081ARDB
+#define CONFIG_QIXIS_I2C_ACCESS
+#endif
#define CONFIG_SYS_I2C_EARLY_INIT
#define CONFIG_DISPLAY_BOARDINFO_LATE
#endif
#endif
#define CONFIG_SYS_LS_MC_BOOT_TIMEOUT_MS 5000
+#ifdef CONFIG_TARGET_LS2081ARDB
+#define CONFIG_FSL_QIXIS /* use common QIXIS code */
+#define QIXIS_QMAP_MASK 0x07
+#define QIXIS_QMAP_SHIFT 5
+#define QIXIS_LBMAP_DFLTBANK 0x00
+#define QIXIS_LBMAP_QSPI 0x00
+#define QIXIS_RCW_SRC_QSPI 0x62
+#define QIXIS_LBMAP_ALTBANK 0x20
+#define QIXIS_RST_CTL_RESET 0x31
+#define QIXIS_RCFG_CTL_RECONFIG_IDLE 0x20
+#define QIXIS_RCFG_CTL_RECONFIG_START 0x21
+#define QIXIS_RCFG_CTL_WATCHDOG_ENBLE 0x08
+#define QIXIS_LBMAP_MASK 0x0f
+#define QIXIS_RST_CTL_RESET_EN 0x30
+#endif
+
/*
* I2C
*/
+#ifdef CONFIG_TARGET_LS2081ARDB
+#define CONFIG_SYS_I2C_FPGA_ADDR 0x66
+#endif
#define I2C_MUX_PCA_ADDR 0x75
#define I2C_MUX_PCA_ADDR_PRI 0x75 /* Primary Mux*/
#define CONFIG_SPI_FLASH_STMICRO
#endif
#ifdef CONFIG_FSL_QSPI
+#ifdef CONFIG_TARGET_LS2081ARDB
+#define CONFIG_SPI_FLASH_STMICRO
+#else
#define CONFIG_SPI_FLASH_SPANSION
+#endif
#define FSL_QSPI_FLASH_SIZE SZ_64M /* 64MB */
#define FSL_QSPI_FLASH_NUM 2
#endif
* RTC configuration
*/
#define RTC
+#ifdef CONFIG_TARGET_LS2081ARDB
+#define CONFIG_RTC_PCF8563 1
+#define CONFIG_SYS_I2C_RTC_ADDR 0x51
+#else
#define CONFIG_RTC_DS3231 1
#define CONFIG_SYS_I2C_RTC_ADDR 0x68
+#endif
/* EEPROM */
#define CONFIG_ID_EEPROM
projects / platform / kernel / u-boot.git / commitdiff