#define AFE_REGISTER_WRITE_DELAY 10
-/* Initialize the AFE for this phy index. We need to read the AFE setup from
- * the OEM parameters
- */
static void sci_controller_afe_initialization(struct isci_host *ihost)
{
+ struct scu_afe_registers __iomem *afe = &ihost->scu_registers->afe;
const struct sci_oem_params *oem = &ihost->oem_parameters;
struct pci_dev *pdev = ihost->pdev;
u32 afe_status;
u32 phy_id;
/* Clear DFX Status registers */
- writel(0x0081000f, &ihost->scu_registers->afe.afe_dfx_master_control0);
+ writel(0x0081000f, &afe->afe_dfx_master_control0);
udelay(AFE_REGISTER_WRITE_DELAY);
if (is_b0(pdev)) {
/* PM Rx Equalization Save, PM SPhy Rx Acknowledgement
- * Timer, PM Stagger Timer */
- writel(0x0007BFFF, &ihost->scu_registers->afe.afe_pmsn_master_control2);
+ * Timer, PM Stagger Timer
+ */
+ writel(0x0007BFFF, &afe->afe_pmsn_master_control2);
udelay(AFE_REGISTER_WRITE_DELAY);
}
/* Configure bias currents to normal */
if (is_a2(pdev))
- writel(0x00005A00, &ihost->scu_registers->afe.afe_bias_control);
+ writel(0x00005A00, &afe->afe_bias_control);
else if (is_b0(pdev) || is_c0(pdev))
- writel(0x00005F00, &ihost->scu_registers->afe.afe_bias_control);
+ writel(0x00005F00, &afe->afe_bias_control);
udelay(AFE_REGISTER_WRITE_DELAY);
/* Enable PLL */
if (is_b0(pdev) || is_c0(pdev))
- writel(0x80040A08, &ihost->scu_registers->afe.afe_pll_control0);
+ writel(0x80040A08, &afe->afe_pll_control0);
else
- writel(0x80040908, &ihost->scu_registers->afe.afe_pll_control0);
+ writel(0x80040908, &afe->afe_pll_control0);
udelay(AFE_REGISTER_WRITE_DELAY);
/* Wait for the PLL to lock */
do {
- afe_status = readl(&ihost->scu_registers->afe.afe_common_block_status);
+ afe_status = readl(&afe->afe_common_block_status);
udelay(AFE_REGISTER_WRITE_DELAY);
} while ((afe_status & 0x00001000) == 0);
if (is_a2(pdev)) {
- /* Shorten SAS SNW lock time (RxLock timer value from 76 us to 50 us) */
- writel(0x7bcc96ad, &ihost->scu_registers->afe.afe_pmsn_master_control0);
+ /* Shorten SAS SNW lock time (RxLock timer value from 76
+ * us to 50 us)
+ */
+ writel(0x7bcc96ad, &afe->afe_pmsn_master_control0);
udelay(AFE_REGISTER_WRITE_DELAY);
}
for (phy_id = 0; phy_id < SCI_MAX_PHYS; phy_id++) {
+ struct scu_afe_transceiver *xcvr = &afe->scu_afe_xcvr[phy_id];
const struct sci_phy_oem_params *oem_phy = &oem->phys[phy_id];
if (is_b0(pdev)) {
/* Configure transmitter SSC parameters */
- writel(0x00030000, &ihost->scu_registers->afe.scu_afe_xcvr[phy_id].afe_tx_ssc_control);
+ writel(0x00030000, &xcvr->afe_tx_ssc_control);
udelay(AFE_REGISTER_WRITE_DELAY);
} else if (is_c0(pdev)) {
/* Configure transmitter SSC parameters */
- writel(0x0003000, &ihost->scu_registers->afe.scu_afe_xcvr[phy_id].afe_tx_ssc_control);
+ writel(0x0003000, &xcvr->afe_tx_ssc_control);
udelay(AFE_REGISTER_WRITE_DELAY);
- /*
- * All defaults, except the Receive Word Alignament/Comma Detect
- * Enable....(0xe800) */
- writel(0x00004500, &ihost->scu_registers->afe.scu_afe_xcvr[phy_id].afe_xcvr_control0);
+ /* All defaults, except the Receive Word
+ * Alignament/Comma Detect Enable....(0xe800)
+ */
+ writel(0x00004500, &xcvr->afe_xcvr_control0);
udelay(AFE_REGISTER_WRITE_DELAY);
} else {
- /*
- * All defaults, except the Receive Word Alignament/Comma Detect
- * Enable....(0xe800) */
- writel(0x00004512, &ihost->scu_registers->afe.scu_afe_xcvr[phy_id].afe_xcvr_control0);
+ /* All defaults, except the Receive Word
+ * Alignament/Comma Detect Enable....(0xe800)
+ */
+ writel(0x00004512, &xcvr->afe_xcvr_control0);
udelay(AFE_REGISTER_WRITE_DELAY);
- writel(0x0050100F, &ihost->scu_registers->afe.scu_afe_xcvr[phy_id].afe_xcvr_control1);
+ writel(0x0050100F, &xcvr->afe_xcvr_control1);
udelay(AFE_REGISTER_WRITE_DELAY);
}
- /*
- * Power up TX and RX out from power down (PWRDNTX and PWRDNRX)
- * & increase TX int & ext bias 20%....(0xe85c) */
+ /* Power up TX and RX out from power down (PWRDNTX and PWRDNRX)
+ * & increase TX int & ext bias 20%....(0xe85c)
+ */
if (is_a2(pdev))
- writel(0x000003F0, &ihost->scu_registers->afe.scu_afe_xcvr[phy_id].afe_channel_control);
+ writel(0x000003F0, &xcvr->afe_channel_control);
else if (is_b0(pdev)) {
/* Power down TX and RX (PWRDNTX and PWRDNRX) */
- writel(0x000003D7, &ihost->scu_registers->afe.scu_afe_xcvr[phy_id].afe_channel_control);
+ writel(0x000003D7, &xcvr->afe_channel_control);
udelay(AFE_REGISTER_WRITE_DELAY);
-
- /*
- * Power up TX and RX out from power down (PWRDNTX and PWRDNRX)
- * & increase TX int & ext bias 20%....(0xe85c) */
- writel(0x000003D4, &ihost->scu_registers->afe.scu_afe_xcvr[phy_id].afe_channel_control);
+ writel(0x000003D4, &xcvr->afe_channel_control);
} else {
- writel(0x000001E7, &ihost->scu_registers->afe.scu_afe_xcvr[phy_id].afe_channel_control);
+ writel(0x000001E7, &xcvr->afe_channel_control);
udelay(AFE_REGISTER_WRITE_DELAY);
-
- /*
- * Power up TX and RX out from power down (PWRDNTX and PWRDNRX)
- * & increase TX int & ext bias 20%....(0xe85c) */
- writel(0x000001E4, &ihost->scu_registers->afe.scu_afe_xcvr[phy_id].afe_channel_control);
+ writel(0x000001E4, &xcvr->afe_channel_control);
}
udelay(AFE_REGISTER_WRITE_DELAY);
if (is_a2(pdev)) {
/* Enable TX equalization (0xe824) */
- writel(0x00040000, &ihost->scu_registers->afe.scu_afe_xcvr[phy_id].afe_tx_control);
+ writel(0x00040000, &xcvr->afe_tx_control);
udelay(AFE_REGISTER_WRITE_DELAY);
}
- /*
- * RDPI=0x0(RX Power On), RXOOBDETPDNC=0x0, TPD=0x0(TX Power On),
- * RDD=0x0(RX Detect Enabled) ....(0xe800) */
- writel(0x00004100, &ihost->scu_registers->afe.scu_afe_xcvr[phy_id].afe_xcvr_control0);
+ writel(0x00004100, &xcvr->afe_xcvr_control0);
udelay(AFE_REGISTER_WRITE_DELAY);
/* Leave DFE/FFE on */
if (is_a2(pdev))
- writel(0x3F11103F, &ihost->scu_registers->afe.scu_afe_xcvr[phy_id].afe_rx_ssc_control0);
+ writel(0x3F11103F, &xcvr->afe_rx_ssc_control0);
else if (is_b0(pdev)) {
- writel(0x3F11103F, &ihost->scu_registers->afe.scu_afe_xcvr[phy_id].afe_rx_ssc_control0);
+ writel(0x3F11103F, &xcvr->afe_rx_ssc_control0);
udelay(AFE_REGISTER_WRITE_DELAY);
/* Enable TX equalization (0xe824) */
- writel(0x00040000, &ihost->scu_registers->afe.scu_afe_xcvr[phy_id].afe_tx_control);
+ writel(0x00040000, &xcvr->afe_tx_control);
} else {
- writel(0x0140DF0F, &ihost->scu_registers->afe.scu_afe_xcvr[phy_id].afe_rx_ssc_control1);
+ writel(0x0140DF0F, &xcvr->afe_rx_ssc_control1);
udelay(AFE_REGISTER_WRITE_DELAY);
- writel(0x3F6F103F, &ihost->scu_registers->afe.scu_afe_xcvr[phy_id].afe_rx_ssc_control0);
+ writel(0x3F6F103F, &xcvr->afe_rx_ssc_control0);
udelay(AFE_REGISTER_WRITE_DELAY);
/* Enable TX equalization (0xe824) */
- writel(0x00040000, &ihost->scu_registers->afe.scu_afe_xcvr[phy_id].afe_tx_control);
+ writel(0x00040000, &xcvr->afe_tx_control);
}
udelay(AFE_REGISTER_WRITE_DELAY);
- writel(oem_phy->afe_tx_amp_control0,
- &ihost->scu_registers->afe.scu_afe_xcvr[phy_id].afe_tx_amp_control0);
+ writel(oem_phy->afe_tx_amp_control0, &xcvr->afe_tx_amp_control0);
udelay(AFE_REGISTER_WRITE_DELAY);
- writel(oem_phy->afe_tx_amp_control1,
- &ihost->scu_registers->afe.scu_afe_xcvr[phy_id].afe_tx_amp_control1);
+ writel(oem_phy->afe_tx_amp_control1, &xcvr->afe_tx_amp_control1);
udelay(AFE_REGISTER_WRITE_DELAY);
- writel(oem_phy->afe_tx_amp_control2,
- &ihost->scu_registers->afe.scu_afe_xcvr[phy_id].afe_tx_amp_control2);
+ writel(oem_phy->afe_tx_amp_control2, &xcvr->afe_tx_amp_control2);
udelay(AFE_REGISTER_WRITE_DELAY);
- writel(oem_phy->afe_tx_amp_control3,
- &ihost->scu_registers->afe.scu_afe_xcvr[phy_id].afe_tx_amp_control3);
+ writel(oem_phy->afe_tx_amp_control3, &xcvr->afe_tx_amp_control3);
udelay(AFE_REGISTER_WRITE_DELAY);
}
/* Transfer control to the PEs */
- writel(0x00010f00, &ihost->scu_registers->afe.afe_dfx_master_control0);
+ writel(0x00010f00, &afe->afe_dfx_master_control0);
udelay(AFE_REGISTER_WRITE_DELAY);
}
static enum sci_status
sci_phy_link_layer_initialization(struct isci_phy *iphy,
- struct scu_link_layer_registers __iomem *reg)
+ struct scu_link_layer_registers __iomem *llr)
{
struct isci_host *ihost = iphy->owning_port->owning_controller;
+ struct sci_phy_user_params *phy_user;
+ struct sci_phy_oem_params *phy_oem;
int phy_idx = iphy->phy_index;
- struct sci_phy_user_params *phy_user = &ihost->user_parameters.phys[phy_idx];
- struct sci_phy_oem_params *phy_oem =
- &ihost->oem_parameters.phys[phy_idx];
- u32 phy_configuration;
struct sci_phy_cap phy_cap;
+ u32 phy_configuration;
u32 parity_check = 0;
u32 parity_count = 0;
u32 llctl, link_rate;
u32 clksm_value = 0;
u32 sp_timeouts = 0;
- iphy->link_layer_registers = reg;
+ phy_user = &ihost->user_parameters.phys[phy_idx];
+ phy_oem = &ihost->oem_parameters.phys[phy_idx];
+ iphy->link_layer_registers = llr;
/* Set our IDENTIFY frame data */
#define SCI_END_DEVICE 0x01
SCU_SAS_TIID_GEN_BIT(STP_INITIATOR) |
SCU_SAS_TIID_GEN_BIT(DA_SATA_HOST) |
SCU_SAS_TIID_GEN_VAL(DEVICE_TYPE, SCI_END_DEVICE),
- &iphy->link_layer_registers->transmit_identification);
+ &llr->transmit_identification);
/* Write the device SAS Address */
- writel(0xFEDCBA98,
- &iphy->link_layer_registers->sas_device_name_high);
- writel(phy_idx, &iphy->link_layer_registers->sas_device_name_low);
+ writel(0xFEDCBA98, &llr->sas_device_name_high);
+ writel(phy_idx, &llr->sas_device_name_low);
/* Write the source SAS Address */
- writel(phy_oem->sas_address.high,
- &iphy->link_layer_registers->source_sas_address_high);
- writel(phy_oem->sas_address.low,
- &iphy->link_layer_registers->source_sas_address_low);
+ writel(phy_oem->sas_address.high, &llr->source_sas_address_high);
+ writel(phy_oem->sas_address.low, &llr->source_sas_address_low);
/* Clear and Set the PHY Identifier */
- writel(0, &iphy->link_layer_registers->identify_frame_phy_id);
- writel(SCU_SAS_TIPID_GEN_VALUE(ID, phy_idx),
- &iphy->link_layer_registers->identify_frame_phy_id);
+ writel(0, &llr->identify_frame_phy_id);
+ writel(SCU_SAS_TIPID_GEN_VALUE(ID, phy_idx), &llr->identify_frame_phy_id);
/* Change the initial state of the phy configuration register */
- phy_configuration =
- readl(&iphy->link_layer_registers->phy_configuration);
+ phy_configuration = readl(&llr->phy_configuration);
/* Hold OOB state machine in reset */
phy_configuration |= SCU_SAS_PCFG_GEN_BIT(OOB_RESET);
- writel(phy_configuration,
- &iphy->link_layer_registers->phy_configuration);
+ writel(phy_configuration, &llr->phy_configuration);
/* Configure the SNW capabilities */
phy_cap.all = 0;
phy_cap.gen1_ssc = 1;
}
- /*
- * The SAS specification indicates that the phy_capabilities that
- * are transmitted shall have an even parity. Calculate the parity. */
+ /* The SAS specification indicates that the phy_capabilities that
+ * are transmitted shall have an even parity. Calculate the parity.
+ */
parity_check = phy_cap.all;
while (parity_check != 0) {
if (parity_check & 0x1)
parity_check >>= 1;
}
- /*
- * If parity indicates there are an odd number of bits set, then
- * set the parity bit to 1 in the phy capabilities. */
+ /* If parity indicates there are an odd number of bits set, then
+ * set the parity bit to 1 in the phy capabilities.
+ */
if ((parity_count % 2) != 0)
phy_cap.parity = 1;
- writel(phy_cap.all, &iphy->link_layer_registers->phy_capabilities);
+ writel(phy_cap.all, &llr->phy_capabilities);
/* Set the enable spinup period but disable the ability to send
* notify enable spinup
*/
writel(SCU_ENSPINUP_GEN_VAL(COUNT,
phy_user->notify_enable_spin_up_insertion_frequency),
- &iphy->link_layer_registers->notify_enable_spinup_control);
+ &llr->notify_enable_spinup_control);
/* Write the ALIGN Insertion Ferequency for connected phy and
* inpendent of connected state
clksm_value |= SCU_ALIGN_INSERTION_FREQUENCY_GEN_VAL(GENERAL,
phy_user->align_insertion_frequency);
- writel(clksm_value, &iphy->link_layer_registers->clock_skew_management);
+ writel(clksm_value, &llr->clock_skew_management);
/* @todo Provide a way to write this register correctly */
- writel(0x02108421,
- &iphy->link_layer_registers->afe_lookup_table_control);
+ writel(0x02108421, &llr->afe_lookup_table_control);
llctl = SCU_SAS_LLCTL_GEN_VAL(NO_OUTBOUND_TASK_TIMEOUT,
(u8)ihost->user_parameters.no_outbound_task_timeout);
break;
}
llctl |= SCU_SAS_LLCTL_GEN_VAL(MAX_LINK_RATE, link_rate);
- writel(llctl, &iphy->link_layer_registers->link_layer_control);
+ writel(llctl, &llr->link_layer_control);
- sp_timeouts = readl(&iphy->link_layer_registers->sas_phy_timeouts);
+ sp_timeouts = readl(&llr->sas_phy_timeouts);
/* Clear the default 0x36 (54us) RATE_CHANGE timeout value. */
sp_timeouts &= ~SCU_SAS_PHYTOV_GEN_VAL(RATE_CHANGE, 0xFF);
*/
sp_timeouts |= SCU_SAS_PHYTOV_GEN_VAL(RATE_CHANGE, 0x3B);
- writel(sp_timeouts, &iphy->link_layer_registers->sas_phy_timeouts);
+ writel(sp_timeouts, &llr->sas_phy_timeouts);
if (is_a2(ihost->pdev)) {
- /* Program the max ARB time for the PHY to 700us so we inter-operate with
- * the PMC expander which shuts down PHYs if the expander PHY generates too
- * many breaks. This time value will guarantee that the initiator PHY will
- * generate the break.
+ /* Program the max ARB time for the PHY to 700us so we
+ * inter-operate with the PMC expander which shuts down
+ * PHYs if the expander PHY generates too many breaks.
+ * This time value will guarantee that the initiator PHY
+ * will generate the break.
*/
writel(SCIC_SDS_PHY_MAX_ARBITRATION_WAIT_TIME,
- &iphy->link_layer_registers->maximum_arbitration_wait_timer_timeout);
+ &llr->maximum_arbitration_wait_timer_timeout);
}
- /* Disable link layer hang detection, rely on the OS timeout for I/O timeouts. */
- writel(0, &iphy->link_layer_registers->link_layer_hang_detection_timeout);
+ /* Disable link layer hang detection, rely on the OS timeout for
+ * I/O timeouts.
+ */
+ writel(0, &llr->link_layer_hang_detection_timeout);
/* We can exit the initial state to the stopped state */
sci_change_state(&iphy->sm, SCI_PHY_STOPPED);
projects / profile / ivi / kernel-x86-ivi.git / commitdiff