--- /dev/null
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2016 Marvell International Ltd.
+ * Copyright (C) 2020 Sartura Ltd.
+ */
+
+#include "armada-8040.dtsi" /* include SoC device tree */
+
+/ {
+ model = "iEi-Puzzle-M801";
+ compatible = "marvell,armada8040-puzzle-m801",
+ "marvell,armada8040";
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ aliases {
+ i2c0 = &i2c0;
+ i2c1 = &cpm_i2c0;
+ i2c2 = &cpm_i2c1;
+ i2c3 = &i2c_switch;
+ spi0 = &spi0;
+ gpio0 = &ap_gpio0;
+ gpio1 = &cpm_gpio0;
+ gpio2 = &cpm_gpio1;
+ gpio3 = &sfpplus_gpio;
+ };
+
+ memory@00000000 {
+ device_type = "memory";
+ reg = <0x0 0x0 0x0 0x80000000>;
+ };
+
+ simple-bus {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ reg_usb3h0_vbus: usb3-vbus0 {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&cpm_xhci_vbus_pins>;
+ regulator-name = "reg-usb3h0-vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ startup-delay-us = <500000>;
+ enable-active-high;
+ regulator-always-on;
+ regulator-boot-on;
+ gpio = <&cpm_gpio1 15 GPIO_ACTIVE_HIGH>; /* GPIO[47] */
+ };
+ };
+};
+
+&i2c0 {
+ status = "okay";
+ clock-frequency = <100000>;
+
+ rtc@32 {
+ compatible = "epson,rx8010";
+ reg = <0x32>;
+ };
+};
+
+&uart0 {
+ status = "okay";
+};
+
+&ap_pinctl {
+ /*
+ * MPP Bus:
+ * AP SPI0 [0-3]
+ * AP I2C [4-5]
+ * AP GPIO [6]
+ * AP UART 1 RX/TX [7-8]
+ * AP GPIO [9-10]
+ * AP GPIO [12]
+ * UART0 [11,19]
+ */
+ /* 0 1 2 3 4 5 6 7 8 9 */
+ pin-func = < 3 3 3 3 3 3 3 3 3 0
+ 0 3 0 0 0 0 0 0 0 3 >;
+};
+
+&cpm_pinctl {
+ /*
+ * MPP Bus:
+ * [0-31] = 0xff: Keep default CP0_shared_pins:
+ * [11] CLKOUT_MPP_11 (out)
+ * [23] LINK_RD_IN_CP2CP (in)
+ * [25] CLKOUT_MPP_25 (out)
+ * [29] AVS_FB_IN_CP2CP (in)
+ * [32,34] SMI
+ * [33] MSS power down
+ * [35-38] CP0 I2C1 and I2C0
+ * [39] MSS CKE Enable
+ * [40,41] CP0 UART1 TX/RX
+ * [42,43] XSMI (controls two 10G phys)
+ * [47] USB VBUS EN
+ * [48] FAN PWM
+ * [49] 10G port 1 interrupt
+ * [50] 10G port 0 interrupt
+ * [51] 2.5G SFP TX fault
+ * [52] PCIe reset out
+ * [53] 2.5G SFP mode
+ * [54] 2.5G SFP LOS
+ * [55] Micro SD card detect
+ * [56-61] Micro SD
+ * [62] CP1 SFI SFP FAULT
+ */
+ /* 0 1 2 3 4 5 6 7 8 9 */
+ pin-func = < 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff
+ 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff
+ 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff
+ 0xff 0 7 0xa 7 2 2 2 2 0xa
+ 7 7 8 8 0 0 0 0 0 0
+ 0 0 0 0 0 0 0xe 0xe 0xe 0xe
+ 0xe 0xe 0 >;
+
+ cpm_xhci_vbus_pins: cpm-xhci-vbus-pins {
+ marvell,pins = < 47 >;
+ marvell,function = <0>;
+ };
+
+ cpm_pcie_reset_pins: cpm-pcie-reset-pins {
+ marvell,pins = < 52 >;
+ marvell,function = <0>;
+ };
+};
+
+&cpm_sdhci0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&cpm_sdhci_pins>;
+ bus-width= <4>;
+ status = "okay";
+};
+
+&cpm_pcie0 {
+ num-lanes = <1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&cpm_pcie_reset_pins>;
+ marvell,reset-gpio = <&cpm_gpio1 20 GPIO_ACTIVE_LOW>; /* GPIO[52] */
+ status = "okay";
+};
+
+&cpm_i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&cpm_i2c0_pins>;
+ status = "okay";
+ clock-frequency = <100000>;
+
+ sfpplus_gpio: gpio@21 {
+ compatible = "nxp,pca9555";
+ reg = <0x21>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+};
+
+&cpm_i2c1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&cpm_i2c1_pins>;
+ status = "okay";
+ clock-frequency = <100000>;
+
+ i2c_switch: i2c-switch@70 {
+ compatible = "nxp,pca9544";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x70>;
+ };
+};
+
+&cpm_sata0 {
+ status = "okay";
+};
+
+&cpm_ethernet {
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&cpm_mdio {
+ status = "okay";
+ cpm_ge_phy0: ethernet-phy@1 {
+ reg = <0>;
+ };
+
+ cpm_ge_phy1: ethernet-phy@2 {
+ reg = <1>;
+ };
+};
+
+&cpm_eth0 {
+ status = "okay";
+ phy-mode = "sfi";
+};
+
+&cpm_eth1 {
+ status = "okay";
+ phy-mode = "sgmii";
+ phy = <&cpm_ge_phy0>;
+};
+
+&cpm_eth2 {
+ status = "okay";
+ phy-mode = "sgmii";
+ phy = <&cpm_ge_phy1>;
+};
+
+&cpm_comphy {
+ /*
+ * CP0 Serdes Configuration:
+ * Lane 0: PCIe0 (x1)
+ * Lane 1: SGMII2
+ * Lane 2: SATA0
+ * Lane 3: SGMII1
+ * Lane 4: SFI (10G)
+ * Lane 5: SATA1
+ */
+ phy0 {
+ phy-type = <PHY_TYPE_PEX0>;
+ };
+ phy1 {
+ phy-type = <PHY_TYPE_SGMII2>;
+ phy-speed = <PHY_SPEED_1_25G>;
+ };
+ phy2 {
+ phy-type = <PHY_TYPE_SATA0>;
+ };
+ phy3 {
+ phy-type = <PHY_TYPE_SGMII1>;
+ phy-speed = <PHY_SPEED_1_25G>;
+ };
+ phy4 {
+ phy-type = <PHY_TYPE_SFI>;
+ };
+ phy5 {
+ phy-type = <PHY_TYPE_SATA1>;
+ };
+};
+
+&cps_mdio {
+ status = "okay";
+ cps_ge_phy0: ethernet-phy@3 {
+ reg = <1>;
+ };
+
+ cps_ge_phy1: ethernet-phy@4 {
+ reg = <0>;
+ };
+};
+
+&cps_pcie0 {
+ num-lanes = <2>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&cps_usb3_0 {
+ vbus-supply = <®_usb3h0_vbus>;
+ status = "okay";
+};
+
+&cps_utmi0 {
+ status = "okay";
+};
+
+&cps_ethernet {
+ status = "okay";
+};
+
+&cps_eth0 {
+ status = "okay";
+ phy-mode = "sfi";
+};
+
+&cps_eth1 {
+ status = "okay";
+ phy = <&cps_ge_phy0>;
+ phy-mode = "sgmii";
+};
+
+&cps_eth2 {
+ status = "okay";
+ phy = <&cps_ge_phy1>;
+ phy-mode = "sgmii";
+};
+
+&cps_pinctl {
+ /*
+ * MPP Bus:
+ * [0-5] TDM
+ * [6,7] CP1_UART 0
+ * [8] CP1 10G SFP LOS
+ * [9] CP1 10G PHY RESET
+ * [10] CP1 10G SFP TX Disable
+ * [11] CP1 10G SFP Mode
+ * [12] SPI1 CS1n
+ * [13] SPI1 MISO (TDM and SPI ROM shared)
+ * [14] SPI1 CS0n
+ * [15] SPI1 MOSI (TDM and SPI ROM shared)
+ * [16] SPI1 CLK (TDM and SPI ROM shared)
+ * [24] CP1 2.5G SFP TX Disable
+ * [26] CP0 10G SFP TX Fault
+ * [27] CP0 10G SFP Mode
+ * [28] CP0 10G SFP LOS
+ * [29] CP0 10G SFP TX Disable
+ * [30] USB Over current indication
+ * [31] 10G Port 0 phy reset
+ * [32-62] = 0xff: Keep default CP1_shared_pins:
+ */
+ /* 0 1 2 3 4 5 6 7 8 9 */
+ pin-func = < 0x4 0x4 0x4 0x4 0x4 0x4 0x8 0x8 0x0 0x0
+ 0x0 0x0 0x3 0x3 0x3 0x3 0x3 0xff 0xff 0xff
+ 0xff 0xff 0xff 0xff 0x0 0xff 0x0 0x0 0x0 0x0
+ 0x0 0x0 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff
+ 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff
+ 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff
+ 0xff 0xff 0xff>;
+};
+
+&spi0 {
+ status = "okay";
+
+ spi-flash@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <10000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@u-boot {
+ reg = <0x00000000 0x001f0000>;
+ label = "u-boot";
+ };
+ partition@u-boot-env {
+ reg = <0x001f0000 0x00010000>;
+ label = "u-boot-env";
+ };
+ partition@ubi1 {
+ reg = <0x00200000 0x03f00000>;
+ label = "ubi1";
+ };
+ partition@ubi2 {
+ reg = <0x04100000 0x03f00000>;
+ label = "ubi2";
+ };
+ };
+ };
+};
+
+&cps_comphy {
+ /*
+ * CP1 Serdes Configuration:
+ * Lane 0: PCIe0 (x2)
+ * Lane 1: PCIe0 (x2)
+ * Lane 2: USB HOST 0
+ * Lane 3: SGMII1
+ * Lane 4: SFI (10G)
+ * Lane 5: SGMII2
+ */
+ phy0 {
+ phy-type = <PHY_TYPE_PEX0>;
+ };
+ phy1 {
+ phy-type = <PHY_TYPE_PEX0>;
+ };
+ phy2 {
+ phy-type = <PHY_TYPE_USB3_HOST0>;
+ };
+ phy3 {
+ phy-type = <PHY_TYPE_SGMII1>;
+ phy-speed = <PHY_SPEED_1_25G>;
+ };
+ phy4 {
+ phy-type = <PHY_TYPE_SFI>;
+ };
+ phy5 {
+ phy-type = <PHY_TYPE_SGMII2>;
+ phy-speed = <PHY_SPEED_1_25G>;
+ };
+};
--- /dev/null
+CONFIG_ARM=y
+CONFIG_ARCH_CPU_INIT=y
+CONFIG_ARCH_MVEBU=y
+CONFIG_SYS_TEXT_BASE=0x00000000
+CONFIG_SYS_MALLOC_F_LEN=0x2000
+CONFIG_TARGET_MVEBU_ARMADA_8K=y
+CONFIG_ENV_SIZE=0x10000
+CONFIG_ENV_SECT_SIZE=0x10000
+CONFIG_ENV_OFFSET=0x1F0000
+CONFIG_NR_DRAM_BANKS=2
+CONFIG_DEBUG_UART_BASE=0xf0512000
+CONFIG_DEBUG_UART_CLOCK=200000000
+CONFIG_DEBUG_UART=y
+CONFIG_AHCI=y
+CONFIG_DISTRO_DEFAULTS=y
+# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
+CONFIG_USE_PREBOOT=y
+CONFIG_SYS_CONSOLE_INFO_QUIET=y
+# CONFIG_DISPLAY_CPUINFO is not set
+# CONFIG_DISPLAY_BOARDINFO is not set
+CONFIG_DISPLAY_BOARDINFO_LATE=y
+CONFIG_AUTOBOOT_KEYED=y
+CONFIG_AUTOBOOT_PROMPT="Autoboot in %d seconds, to stop use 's' key\n"
+CONFIG_AUTOBOOT_STOP_STR="s"
+CONFIG_AUTOBOOT_KEYED_CTRLC=y
+CONFIG_ARCH_EARLY_INIT_R=y
+CONFIG_BOARD_EARLY_INIT_F=y
+# CONFIG_EFI_LOADER is not set
+# CONFIG_CMD_FLASH is not set
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_PCI=y
+CONFIG_CMD_SPI=y
+CONFIG_CMD_USB=y
+# CONFIG_CMD_SETEXPR is not set
+CONFIG_CMD_TFTPPUT=y
+CONFIG_CMD_CACHE=y
+CONFIG_CMD_TIME=y
+CONFIG_CMD_MVEBU_BUBT=y
+CONFIG_CMD_REGULATOR=y
+CONFIG_CMD_EXT4_WRITE=y
+CONFIG_MAC_PARTITION=y
+CONFIG_DEFAULT_DEVICE_TREE="armada-8040-puzzle-m801"
+CONFIG_ENV_IS_IN_SPI_FLASH=y
+CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_NET_RANDOM_ETHADDR=y
+CONFIG_AHCI_MVEBU=y
+CONFIG_DM_GPIO=y
+CONFIG_DM_PCA953X=y
+CONFIG_DM_I2C=y
+CONFIG_SYS_I2C_MVTWSI=y
+CONFIG_I2C_MUX=y
+CONFIG_I2C_MUX_PCA954x=y
+CONFIG_DM_RTC=y
+CONFIG_RTC_RX8010SJ=y
+CONFIG_MISC=y
+CONFIG_DM_MMC=y
+CONFIG_MMC_SDHCI=y
+CONFIG_MMC_SDHCI_XENON=y
+CONFIG_SF_DEFAULT_MODE=0
+CONFIG_SPI_FLASH_SFDP_SUPPORT=y
+CONFIG_SPI_FLASH_BAR=y
+CONFIG_SPI_FLASH_MACRONIX=y
+# CONFIG_SPI_FLASH_SPANSION is not set
+# CONFIG_SPI_FLASH_STMICRO is not set
+# CONFIG_SPI_FLASH_WINBOND is not set
+CONFIG_PHY_MARVELL=y
+CONFIG_PHY_GIGE=y
+CONFIG_MVPP2=y
+CONFIG_NVME=y
+CONFIG_PCI=y
+CONFIG_DM_PCI=y
+CONFIG_PCIE_DW_MVEBU=y
+CONFIG_MVEBU_COMPHY_SUPPORT=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_ARMADA_8K=y
+CONFIG_DM_REGULATOR_FIXED=y
+CONFIG_DEBUG_UART_SHIFT=2
+CONFIG_DEBUG_UART_ANNOUNCE=y
+CONFIG_SYS_NS16550=y
+CONFIG_KIRKWOOD_SPI=y
+CONFIG_USB=y
+CONFIG_DM_USB=y
+CONFIG_USB_XHCI_HCD=y
+CONFIG_USB_EHCI_HCD=y
+# CONFIG_USB_HOST_ETHER is not set
+# CONFIG_USB_ETHER_ASIX is not set
+# CONFIG_USB_ETHER_MCS7830 is not set
+# CONFIG_USB_ETHER_RTL8152 is not set
+# CONFIG_USB_ETHER_SMSC95XX is not set
projects / platform / kernel / u-boot.git / commitdiff