#define GPSCS 0x51 /* General Purpose SPDIF channel status register */
+// Corresponding EMU10K1_DBG_* constants are in the public header
#define DBG 0x52
#define A_SPSC 0x52 /* S/PDIF Input C Channel Status */
#define REG53 0x53 /* DO NOT PROGRAM THIS REGISTER!!! MAY DESTROY CHIP */
-#define A_DBG 0x53
-#define A_DBG_SINGLE_STEP 0x00020000 /* Set to zero to start dsp */
-#define A_DBG_ZC 0x40000000 /* zero tram counter */
-#define A_DBG_STEP_ADDR 0x000003ff
-#define A_DBG_SATURATION_OCCURED 0x20000000
-#define A_DBG_SATURATION_ADDR 0x0ffc0000
+// Corresponding A_DBG_* constants are in the public header
+#define A_DBG 0x53
// NOTE: 0x54,55,56: 64-bit (split over voices 0 & 1)
#define SPCS0 0x54 /* SPDIF output Channel Status 0 register */
#define A_FXRT_CHANNELD 0x3f000000
/* 0x7f: Not used */
-/* Each FX general purpose register is 32 bits in length, all bits are used */
-#define FXGPREGBASE 0x100 /* FX general purpose registers base */
-#define A_FXGPREGBASE 0x400 /* Audigy GPRs, 0x400 to 0x5ff */
-
-#define A_TANKMEMCTLREGBASE 0x100 /* Tank memory control registers base - only for Audigy */
-#define A_TANKMEMCTLREG_MASK 0x1f /* only 5 bits used - only for Audigy */
-
-/* Tank audio data is logarithmically compressed down to 16 bits before writing to TRAM and is */
-/* decompressed back to 20 bits on a read. There are a total of 160 locations, the last 32 */
-/* locations are for external TRAM. */
-#define TANKMEMDATAREGBASE 0x200 /* Tank memory data registers base */
-#define TANKMEMDATAREG_MASK 0x000fffff /* 20 bit tank audio data field */
-
-/* Combined address field and memory opcode or flag field. 160 locations, last 32 are external */
-#define TANKMEMADDRREGBASE 0x300 /* Tank memory address registers base */
-#define TANKMEMADDRREG_ADDR_MASK 0x000fffff /* 20 bit tank address field */
-#define TANKMEMADDRREG_CLEAR 0x00800000 /* Clear tank memory */
-#define TANKMEMADDRREG_ALIGN 0x00400000 /* Align read or write relative to tank access */
-#define TANKMEMADDRREG_WRITE 0x00200000 /* Write to tank memory */
-#define TANKMEMADDRREG_READ 0x00100000 /* Read from tank memory */
-#define MICROCODEBASE 0x400 /* Microcode data base address */
+/* The public header defines the GPR and TRAM base addresses that
+ * are valid for _both_ CPU and DSP addressing. */
/* Each DSP microcode instruction is mapped into 2 doublewords */
/* NOTE: When writing, always write the LO doubleword first. Reads can be in either order. */
-#define LOWORD_OPX_MASK 0x000ffc00 /* Instruction operand X */
-#define LOWORD_OPY_MASK 0x000003ff /* Instruction operand Y */
-#define HIWORD_OPCODE_MASK 0x00f00000 /* Instruction opcode */
-#define HIWORD_RESULT_MASK 0x000ffc00 /* Instruction result */
-#define HIWORD_OPA_MASK 0x000003ff /* Instruction operand A */
-
-
-/* Audigy Soundcard have a different instruction format */
+#define MICROCODEBASE 0x400 /* Microcode data base address */
#define A_MICROCODEBASE 0x600
-#define A_LOWORD_OPY_MASK 0x000007ff
-#define A_LOWORD_OPX_MASK 0x007ff000
-#define A_HIWORD_OPCODE_MASK 0x0f000000
-#define A_HIWORD_RESULT_MASK 0x007ff000
-#define A_HIWORD_OPA_MASK 0x000007ff
/************************************************************************************************/
#define iINTERP 0x0e /* R = A + (X * (Y - A) >> 31) ; saturation */
#define iSKIP 0x0f /* R = A (cc_reg), X (count), Y (cc_test) */
+#define LOWORD_OPX_MASK 0x000ffc00 /* Instruction operand X */
+#define LOWORD_OPY_MASK 0x000003ff /* Instruction operand Y */
+#define HIWORD_OPCODE_MASK 0x00f00000 /* Instruction opcode */
+#define HIWORD_RESULT_MASK 0x000ffc00 /* Instruction result */
+#define HIWORD_OPA_MASK 0x000003ff /* Instruction operand A */
+
+/* Audigy Soundcards have a different instruction format */
+#define A_LOWORD_OPX_MASK 0x007ff000
+#define A_LOWORD_OPY_MASK 0x000007ff
+#define A_HIWORD_OPCODE_MASK 0x0f000000
+#define A_HIWORD_RESULT_MASK 0x007ff000
+#define A_HIWORD_OPA_MASK 0x000007ff
+
/* GPRs */
#define FXBUS(x) (0x00 + (x)) /* x = 0x00 - 0x0f */
#define EXTIN(x) (0x10 + (x)) /* x = 0x00 - 0x0f */
#define FXBUS2(x) (0x30 + (x)) /* x = 0x00 - 0x0f copies of fx buses for capture -> FXWC high 16 bits */
/* NB: 0x31 and 0x32 are shared with Center/LFE on SB live 5.1 */
+#define A_FXBUS(x) (0x00 + (x)) /* x = 0x00 - 0x3f FX buses */
+#define A_EXTIN(x) (0x40 + (x)) /* x = 0x00 - 0x0f physical ins */
+#define A_P16VIN(x) (0x50 + (x)) /* x = 0x00 - 0x0f p16v ins (A2 only) "EMU32 inputs" */
+#define A_EXTOUT(x) (0x60 + (x)) /* x = 0x00 - 0x1f physical outs -> A_FXWC1 0x79-7f unknown */
+#define A_FXBUS2(x) (0x80 + (x)) /* x = 0x00 - 0x1f extra outs used for EFX capture -> A_FXWC2 */
+#define A_EMU32OUTH(x) (0xa0 + (x)) /* x = 0x00 - 0x0f "EMU32_OUT_10 - _1F" */
+#define A_EMU32OUTL(x) (0xb0 + (x)) /* x = 0x00 - 0x0f "EMU32_OUT_01 - _0F" */
+#define A3_EMU32IN(x) (0x160 + (x)) /* x = 0x00 - 0x1f "EMU32_IN_00 - _1F" - Only when .device = 0x0008 */
+#define A3_EMU32OUT(x) (0x1E0 + (x)) /* x = 0x00 - 0x1f "EMU32_OUT_00 - _1F" - Only when .device = 0x0008 */
+
#define C_00000000 0x40
#define C_00000001 0x41
#define C_00000002 0x42
#define GPR_NOISE1 0x59 /* noise source */
#define GPR_IRQ 0x5a /* IRQ register */
#define GPR_DBAC 0x5b /* TRAM Delay Base Address Counter */
+
+/* Audigy constants */
+#define A_C_00000000 0xc0
+#define A_C_00000001 0xc1
+#define A_C_00000002 0xc2
+#define A_C_00000003 0xc3
+#define A_C_00000004 0xc4
+#define A_C_00000008 0xc5
+#define A_C_00000010 0xc6
+#define A_C_00000020 0xc7
+#define A_C_00000100 0xc8
+#define A_C_00010000 0xc9
+#define A_C_00000800 0xca
+#define A_C_10000000 0xcb
+#define A_C_20000000 0xcc
+#define A_C_40000000 0xcd
+#define A_C_80000000 0xce
+#define A_C_7fffffff 0xcf
+#define A_C_ffffffff 0xd0
+#define A_C_fffffffe 0xd1
+#define A_C_c0000000 0xd2
+#define A_C_4f1bbcdc 0xd3
+#define A_C_5a7ef9db 0xd4
+#define A_C_00100000 0xd5
+#define A_GPR_ACCU 0xd6 /* ACCUM, accumulator */
+#define A_GPR_COND 0xd7 /* CCR, condition register */
+#define A_GPR_NOISE0 0xd8 /* noise source */
+#define A_GPR_NOISE1 0xd9 /* noise source */
+#define A_GPR_IRQ 0xda /* IRQ register */
+#define A_GPR_DBAC 0xdb /* TRAM Delay Base Address Counter - internal */
+#define A_GPR_DBACE 0xde /* TRAM Delay Base Address Counter - external */
+
+/* Each FX general purpose register is 32 bits in length, all bits are used */
+#define FXGPREGBASE 0x100 /* FX general purpose registers base */
+#define A_FXGPREGBASE 0x400 /* Audigy GPRs, 0x400 to 0x5ff */
+
+#define A_TANKMEMCTLREGBASE 0x100 /* Tank memory control registers base - only for Audigy */
+#define A_TANKMEMCTLREG_MASK 0x1f /* only 5 bits used - only for Audigy */
+
+/* Tank audio data is logarithmically compressed down to 16 bits before writing to TRAM and is */
+/* decompressed back to 20 bits on a read. There are a total of 160 locations, the last 32 */
+/* locations are for external TRAM. */
+#define TANKMEMDATAREGBASE 0x200 /* Tank memory data registers base */
+#define TANKMEMDATAREG_MASK 0x000fffff /* 20 bit tank audio data field */
+
+/* Combined address field and memory opcode or flag field. 160 locations, last 32 are external */
+#define TANKMEMADDRREGBASE 0x300 /* Tank memory address registers base */
+#define TANKMEMADDRREG_ADDR_MASK 0x000fffff /* 20 bit tank address field */
+#define TANKMEMADDRREG_CLEAR 0x00800000 /* Clear tank memory */
+#define TANKMEMADDRREG_ALIGN 0x00400000 /* Align read or write relative to tank access */
+#define TANKMEMADDRREG_WRITE 0x00200000 /* Write to tank memory */
+#define TANKMEMADDRREG_READ 0x00100000 /* Read from tank memory */
+
#define GPR(x) (FXGPREGBASE + (x)) /* free GPRs: x = 0x00 - 0xff */
#define ITRAM_DATA(x) (TANKMEMDATAREGBASE + 0x00 + (x)) /* x = 0x00 - 0x7f */
#define ETRAM_DATA(x) (TANKMEMDATAREGBASE + 0x80 + (x)) /* x = 0x00 - 0x1f */
#define ITRAM_ADDR(x) (TANKMEMADDRREGBASE + 0x00 + (x)) /* x = 0x00 - 0x7f */
#define ETRAM_ADDR(x) (TANKMEMADDRREGBASE + 0x80 + (x)) /* x = 0x00 - 0x1f */
+#define A_GPR(x) (A_FXGPREGBASE + (x))
#define A_ITRAM_DATA(x) (TANKMEMDATAREGBASE + 0x00 + (x)) /* x = 0x00 - 0xbf */
#define A_ETRAM_DATA(x) (TANKMEMDATAREGBASE + 0xc0 + (x)) /* x = 0x00 - 0x3f */
#define A_ITRAM_ADDR(x) (TANKMEMADDRREGBASE + 0x00 + (x)) /* x = 0x00 - 0xbf */
#define A_ITRAM_CTL(x) (A_TANKMEMCTLREGBASE + 0x00 + (x)) /* x = 0x00 - 0xbf */
#define A_ETRAM_CTL(x) (A_TANKMEMCTLREGBASE + 0xc0 + (x)) /* x = 0x00 - 0x3f */
-#define A_FXBUS(x) (0x00 + (x)) /* x = 0x00 - 0x3f FX buses */
-#define A_EXTIN(x) (0x40 + (x)) /* x = 0x00 - 0x0f physical ins */
-#define A_P16VIN(x) (0x50 + (x)) /* x = 0x00 - 0x0f p16v ins (A2 only) "EMU32 inputs" */
-#define A_EXTOUT(x) (0x60 + (x)) /* x = 0x00 - 0x1f physical outs -> A_FXWC1 0x79-7f unknown */
-#define A_FXBUS2(x) (0x80 + (x)) /* x = 0x00 - 0x1f extra outs used for EFX capture -> A_FXWC2 */
-#define A_EMU32OUTH(x) (0xa0 + (x)) /* x = 0x00 - 0x0f "EMU32_OUT_10 - _1F" - ??? */
-#define A_EMU32OUTL(x) (0xb0 + (x)) /* x = 0x00 - 0x0f "EMU32_OUT_1 - _F" - ??? */
-#define A3_EMU32IN(x) (0x160 + (x)) /* x = 0x00 - 0x3f "EMU32_IN_00 - _3F" - Only when .device = 0x0008 */
-#define A3_EMU32OUT(x) (0x1E0 + (x)) /* x = 0x00 - 0x0f "EMU32_OUT_00 - _3F" - Only when .device = 0x0008 */
-#define A_GPR(x) (A_FXGPREGBASE + (x))
-
/* cc_reg constants */
#define CC_REG_NORMALIZED C_00000001
#define CC_REG_BORROW C_00000002
#define CC_REG_SATURATE C_00000010
#define CC_REG_NONZERO C_00000100
+#define A_CC_REG_NORMALIZED A_C_00000001
+#define A_CC_REG_BORROW A_C_00000002
+#define A_CC_REG_MINUS A_C_00000004
+#define A_CC_REG_ZERO A_C_00000008
+#define A_CC_REG_SATURATE A_C_00000010
+#define A_CC_REG_NONZERO A_C_00000100
+
/* FX buses */
// These are arbitrary mappings; our DSP code simply expects
// the config files to route the channels this way.
#define A_EXTOUT_ADC_CAP_R 0x17 /* right */
#define A_EXTOUT_MIC_CAP 0x18 /* Mic capture buffer */
-/* Audigy constants */
-#define A_C_00000000 0xc0
-#define A_C_00000001 0xc1
-#define A_C_00000002 0xc2
-#define A_C_00000003 0xc3
-#define A_C_00000004 0xc4
-#define A_C_00000008 0xc5
-#define A_C_00000010 0xc6
-#define A_C_00000020 0xc7
-#define A_C_00000100 0xc8
-#define A_C_00010000 0xc9
-#define A_C_00000800 0xca
-#define A_C_10000000 0xcb
-#define A_C_20000000 0xcc
-#define A_C_40000000 0xcd
-#define A_C_80000000 0xce
-#define A_C_7fffffff 0xcf
-#define A_C_ffffffff 0xd0
-#define A_C_fffffffe 0xd1
-#define A_C_c0000000 0xd2
-#define A_C_4f1bbcdc 0xd3
-#define A_C_5a7ef9db 0xd4
-#define A_C_00100000 0xd5
-#define A_GPR_ACCU 0xd6 /* ACCUM, accumulator */
-#define A_GPR_COND 0xd7 /* CCR, condition register */
-#define A_GPR_NOISE0 0xd8 /* noise source */
-#define A_GPR_NOISE1 0xd9 /* noise source */
-#define A_GPR_IRQ 0xda /* IRQ register */
-#define A_GPR_DBAC 0xdb /* TRAM Delay Base Address Counter - internal */
-#define A_GPR_DBACE 0xde /* TRAM Delay Base Address Counter - external */
-
-/* definitions for debug register */
+/* Definitions for debug register. Note that these are for emu10k1 ONLY. */
#define EMU10K1_DBG_ZC 0x80000000 /* zero tram counter */
#define EMU10K1_DBG_SATURATION_OCCURED 0x02000000 /* saturation control */
#define EMU10K1_DBG_SATURATION_ADDR 0x01ff0000 /* saturation address */
#define EMU10K1_DBG_CONDITION_CODE 0x00003e00 /* condition code */
#define EMU10K1_DBG_SINGLE_STEP_ADDR 0x000001ff /* single step address */
-/* tank memory address line */
-#ifndef __KERNEL__
-#define TANKMEMADDRREG_ADDR_MASK 0x000fffff /* 20 bit tank address field */
-#define TANKMEMADDRREG_CLEAR 0x00800000 /* Clear tank memory */
-#define TANKMEMADDRREG_ALIGN 0x00400000 /* Align read or write relative to tank access */
-#define TANKMEMADDRREG_WRITE 0x00200000 /* Write to tank memory */
-#define TANKMEMADDRREG_READ 0x00100000 /* Read from tank memory */
-#endif
+/* Definitions for emu10k2 debug register. */
+#define A_DBG_ZC 0x40000000 /* zero tram counter */
+#define A_DBG_SATURATION_OCCURED 0x20000000
+#define A_DBG_SATURATION_ADDR 0x0ffc0000
+#define A_DBG_SINGLE_STEP 0x00020000 /* Set to zero to start dsp */
+#define A_DBG_STEP 0x00010000
+#define A_DBG_CONDITION_CODE 0x0000f800
+#define A_DBG_STEP_ADDR 0x000003ff
struct snd_emu10k1_fx8010_info {
unsigned int internal_tram_size; /* in samples */
projects / platform / kernel / linux-starfive.git / commitdiff