/*
- * Copyright (C) 2016 Chen-Yu Tsai <wens@csie.org>
+ * Copyright (C) 2017 Chen-Yu Tsai <wens@csie.org>
+ * Copyright (C) 2017 Icenowy Zheng <icenowy@aosc.io>
*
* This file is dual-licensed: you can use it either under the terms
* of the GPL or the X11 license, at your option. Note that this dual
/dts-v1/;
#include "sun8i-r40.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+
/ {
model = "Banana Pi BPI-M2-Ultra";
compatible = "sinovoip,bpi-m2-ultra", "allwinner,sun8i-r40";
chosen {
stdout-path = "serial0:115200n8";
};
+
+ leds {
+ compatible = "gpio-leds";
+
+ pwr-led {
+ label = "bananapi:red:pwr";
+ gpios = <&pio 7 20 GPIO_ACTIVE_HIGH>;
+ default-state = "on";
+ };
+
+ user-led-green {
+ label = "bananapi:green:user";
+ gpios = <&pio 7 21 GPIO_ACTIVE_HIGH>;
+ };
+
+ user-led-blue {
+ label = "bananapi:blue:user";
+ gpios = <&pio 7 22 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ reg_vcc5v0: vcc5v0 {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc5v0";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&pio 7 23 GPIO_ACTIVE_HIGH>; /* PH23 */
+ enable-active-high;
+ };
+
+ wifi_pwrseq: wifi_pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ reset-gpios = <&pio 6 10 GPIO_ACTIVE_LOW>; /* PG10 WIFI_EN */
+ };
};
-&i2c0 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins>;
+&ehci1 {
status = "okay";
};
-&uart0 {
- pinctrl-names = "default";
- pinctrl-0 = <&uart0_pb_pins>;
+&ehci2 {
status = "okay";
};
pinctrl-0 = <&gmac_rgmii_pins>;
phy-handle = <&phy1>;
phy-mode = "rgmii";
+ phy-supply = <®_dc1sw>;
status = "okay";
};
reg = <1>;
};
};
+
+&i2c0 {
+ status = "okay";
+
+ axp22x: pmic@34 {
+ compatible = "x-powers,axp221";
+ reg = <0x34>;
+ interrupt-parent = <&nmi_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+ };
+};
+
+#include "axp22x.dtsi"
+
+&mmc0 {
+ vmmc-supply = <®_dcdc1>;
+ bus-width = <4>;
+ cd-gpios = <&pio 7 13 GPIO_ACTIVE_HIGH>; /* PH13 */
+ cd-inverted;
+ status = "okay";
+};
+
+&mmc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc1_pg_pins>;
+ vmmc-supply = <®_dldo2>;
+ vqmmc-supply = <®_dldo1>;
+ mmc-pwrseq = <&wifi_pwrseq>;
+ bus-width = <4>;
+ non-removable;
+ status = "okay";
+};
+
+&mmc2 {
+ vmmc-supply = <®_dcdc1>;
+ vqmmc-supply = <®_dcdc1>;
+ bus-width = <8>;
+ non-removable;
+ status = "okay";
+};
+
+&ohci1 {
+ status = "okay";
+};
+
+&ohci2 {
+ status = "okay";
+};
+
+®_aldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <2500000>;
+ regulator-max-microvolt = <2500000>;
+ regulator-name = "vcc-pa";
+};
+
+®_aldo3 {
+ regulator-always-on;
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "avcc";
+};
+
+®_dc1sw {
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcc-gmac-phy";
+};
+
+®_dcdc1 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcc-3v0";
+};
+
+®_dcdc2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-name = "vdd-cpu";
+};
+
+®_dcdc3 {
+ regulator-always-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-name = "vdd-sys";
+};
+
+®_dcdc5 {
+ regulator-always-on;
+ regulator-min-microvolt = <1500000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-name = "vcc-dram";
+};
+
+®_dldo1 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-wifi-io";
+};
+
+®_dldo2 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-wifi";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pb_pins>;
+ status = "okay";
+};
+
+&usbphy {
+ usb1_vbus-supply = <®_vcc5v0>;
+ usb2_vbus-supply = <®_vcc5v0>;
+ status = "okay";
+};
/*
- * Copyright 2016 Chen-Yu Tsai
- *
- * Chen-Yu Tsai <wens@csie.org>
+ * Copyright 2017 Chen-Yu Tsai <wens@csie.org>
+ * Copyright 2017 Icenowy Zheng <icenowy@aosc.io>
*
* This file is dual-licensed: you can use it either under the terms
* of the GPL or the X11 license, at your option. Note that this dual
#size-cells = <1>;
interrupt-parent = <&gic>;
- aliases {
- };
-
- chosen {
- };
-
clocks {
#address-cells = <1>;
#size-cells = <1>;
ranges;
- osc24M: osc24M_clk {
+ osc24M: osc24M {
#clock-cells = <0>;
compatible = "fixed-clock";
clock-frequency = <24000000>;
+ clock-output-names = "osc24M";
};
- osc32k: osc32k_clk {
+ osc32k: osc32k {
#clock-cells = <0>;
compatible = "fixed-clock";
clock-frequency = <32768>;
#address-cells = <1>;
#size-cells = <0>;
- cpu0: cpu@0 {
+ cpu@0 {
compatible = "arm,cortex-a7";
device_type = "cpu";
reg = <0>;
};
};
- memory@40000000 {
- device_type = "memory";
- reg = <0x40000000 0x80000000>;
- };
-
soc {
compatible = "simple-bus";
#address-cells = <1>;
#size-cells = <0>;
};
+ mmc1: mmc@1c10000 {
+ compatible = "allwinner,sun8i-r40-mmc",
+ "allwinner,sun50i-a64-mmc";
+ reg = <0x01c10000 0x1000>;
+ clocks = <&ccu CLK_BUS_MMC1>, <&ccu CLK_MMC1>;
+ clock-names = "ahb", "mmc";
+ resets = <&ccu RST_BUS_MMC1>;
+ reset-names = "ahb";
+ interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ mmc2: mmc@1c11000 {
+ compatible = "allwinner,sun8i-r40-emmc",
+ "allwinner,sun50i-a64-emmc";
+ reg = <0x01c11000 0x1000>;
+ clocks = <&ccu CLK_BUS_MMC2>, <&ccu CLK_MMC2>;
+ clock-names = "ahb", "mmc";
+ resets = <&ccu RST_BUS_MMC2>;
+ reset-names = "ahb";
+ pinctrl-0 = <&mmc2_pins>;
+ pinctrl-names = "default";
+ interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ mmc3: mmc@1c12000 {
+ compatible = "allwinner,sun8i-r40-mmc",
+ "allwinner,sun50i-a64-mmc";
+ reg = <0x01c12000 0x1000>;
+ clocks = <&ccu CLK_BUS_MMC3>, <&ccu CLK_MMC3>;
+ clock-names = "ahb", "mmc";
+ resets = <&ccu RST_BUS_MMC3>;
+ reset-names = "ahb";
+ interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ usbphy: phy@1c13400 {
+ compatible = "allwinner,sun8i-r40-usb-phy";
+ reg = <0x01c13400 0x14>,
+ <0x01c14800 0x4>,
+ <0x01c19800 0x4>,
+ <0x01c1c800 0x4>;
+ reg-names = "phy_ctrl",
+ "pmu0",
+ "pmu1",
+ "pmu2";
+ clocks = <&ccu CLK_USB_PHY0>,
+ <&ccu CLK_USB_PHY1>,
+ <&ccu CLK_USB_PHY2>;
+ clock-names = "usb0_phy",
+ "usb1_phy",
+ "usb2_phy";
+ resets = <&ccu RST_USB_PHY0>,
+ <&ccu RST_USB_PHY1>,
+ <&ccu RST_USB_PHY2>;
+ reset-names = "usb0_reset",
+ "usb1_reset",
+ "usb2_reset";
+ status = "disabled";
+ #phy-cells = <1>;
+ };
+
+ ehci1: usb@1c19000 {
+ compatible = "allwinner,sun8i-r40-ehci", "generic-ehci";
+ reg = <0x01c19000 0x100>;
+ interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_EHCI1>;
+ resets = <&ccu RST_BUS_EHCI1>;
+ phys = <&usbphy 1>;
+ phy-names = "usb";
+ status = "disabled";
+ };
+
+ ohci1: usb@1c19400 {
+ compatible = "allwinner,sun8i-r40-ohci", "generic-ohci";
+ reg = <0x01c19400 0x100>;
+ interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_OHCI1>,
+ <&ccu CLK_USB_OHCI1>;
+ resets = <&ccu RST_BUS_OHCI1>;
+ phys = <&usbphy 1>;
+ phy-names = "usb";
+ status = "disabled";
+ };
+
+ ehci2: usb@1c1c000 {
+ compatible = "allwinner,sun8i-r40-ehci", "generic-ehci";
+ reg = <0x01c1c000 0x100>;
+ interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_EHCI2>;
+ resets = <&ccu RST_BUS_EHCI2>;
+ phys = <&usbphy 2>;
+ phy-names = "usb";
+ status = "disabled";
+ };
+
+ ohci2: usb@1c1c400 {
+ compatible = "allwinner,sun8i-r40-ohci", "generic-ohci";
+ reg = <0x01c1c400 0x100>;
+ interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_OHCI2>,
+ <&ccu CLK_USB_OHCI2>;
+ resets = <&ccu RST_BUS_OHCI2>;
+ phys = <&usbphy 2>;
+ phy-names = "usb";
+ status = "disabled";
+ };
+
ccu: clock@1c20000 {
compatible = "allwinner,sun8i-r40-ccu";
reg = <0x01c20000 0x400>;
compatible = "allwinner,sun8i-r40-pinctrl";
reg = <0x01c20800 0x400>;
interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>;
- /* apb should be replaced once CCU is implemented */
- clocks = <&osc24M>, <&osc24M>, <&osc32k>;
+ clocks = <&ccu CLK_BUS_PIO>, <&osc24M>, <&osc32k>;
clock-names = "apb", "hosc", "losc";
gpio-controller;
interrupt-controller;
drive-strength = <40>;
};
- i2c0_pins: i2c0_pins {
+ i2c0_pins: i2c0-pins {
pins = "PB0", "PB1";
function = "i2c0";
- bias-pull-up;
};
mmc0_pins: mmc0-pins {
bias-pull-up;
};
- uart0_pb_pins: uart0_pb_pins {
+ mmc1_pg_pins: mmc1-pg-pins {
+ pins = "PG0", "PG1", "PG2",
+ "PG3", "PG4", "PG5";
+ function = "mmc1";
+ drive-strength = <30>;
+ bias-pull-up;
+ };
+
+ mmc2_pins: mmc2-pins {
+ pins = "PC5", "PC6", "PC7", "PC8", "PC9",
+ "PC10", "PC11", "PC12", "PC13", "PC14",
+ "PC15", "PC24";
+ function = "mmc2";
+ drive-strength = <30>;
+ bias-pull-up;
+ };
+
+ uart0_pb_pins: uart0-pb-pins {
pins = "PB22", "PB23";
function = "uart0";
- bias-pull-up;
};
};
+ wdt: watchdog@1c20c90 {
+ compatible = "allwinner,sun4i-a10-wdt";
+ reg = <0x01c20c90 0x10>;
+ };
+
uart0: serial@1c28000 {
compatible = "snps,dw-apb-uart";
reg = <0x01c28000 0x400>;
interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
reg-shift = <2>;
reg-io-width = <4>;
- clocks = <&osc24M>;
+ clocks = <&ccu CLK_BUS_UART0>;
+ resets = <&ccu RST_BUS_UART0>;
+ status = "disabled";
+ };
+
+ uart1: serial@1c28400 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x01c28400 0x400>;
+ interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&ccu CLK_BUS_UART1>;
+ resets = <&ccu RST_BUS_UART1>;
+ status = "disabled";
+ };
+
+ uart2: serial@1c28800 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x01c28800 0x400>;
+ interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&ccu CLK_BUS_UART2>;
+ resets = <&ccu RST_BUS_UART2>;
+ status = "disabled";
+ };
+
+ uart3: serial@1c28c00 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x01c28c00 0x400>;
+ interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&ccu CLK_BUS_UART3>;
+ resets = <&ccu RST_BUS_UART3>;
+ status = "disabled";
+ };
+
+ uart4: serial@1c29000 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x01c29000 0x400>;
+ interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&ccu CLK_BUS_UART4>;
+ resets = <&ccu RST_BUS_UART4>;
+ status = "disabled";
+ };
+
+ uart5: serial@1c29400 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x01c29400 0x400>;
+ interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&ccu CLK_BUS_UART5>;
+ resets = <&ccu RST_BUS_UART5>;
+ status = "disabled";
+ };
+
+ uart6: serial@1c29800 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x01c29800 0x400>;
+ interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&ccu CLK_BUS_UART6>;
+ resets = <&ccu RST_BUS_UART6>;
+ status = "disabled";
+ };
+
+ uart7: serial@1c29c00 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x01c29c00 0x400>;
+ interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&ccu CLK_BUS_UART7>;
+ resets = <&ccu RST_BUS_UART7>;
status = "disabled";
};
compatible = "allwinner,sun6i-a31-i2c";
reg = <0x01c2ac00 0x400>;
interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&osc24M>;
+ clocks = <&ccu CLK_BUS_I2C0>;
+ resets = <&ccu RST_BUS_I2C0>;
+ pinctrl-0 = <&i2c0_pins>;
+ pinctrl-names = "default";
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ i2c1: i2c@1c2b000 {
+ compatible = "allwinner,sun6i-a31-i2c";
+ reg = <0x01c2b000 0x400>;
+ interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_I2C1>;
+ resets = <&ccu RST_BUS_I2C1>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ i2c2: i2c@1c2b400 {
+ compatible = "allwinner,sun6i-a31-i2c";
+ reg = <0x01c2b400 0x400>;
+ interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_I2C2>;
+ resets = <&ccu RST_BUS_I2C2>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ i2c3: i2c@1c2b800 {
+ compatible = "allwinner,sun6i-a31-i2c";
+ reg = <0x01c2b800 0x400>;
+ interrupts = <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_I2C3>;
+ resets = <&ccu RST_BUS_I2C3>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ i2c4: i2c@1c2c000 {
+ compatible = "allwinner,sun6i-a31-i2c";
+ reg = <0x01c2c000 0x400>;
+ interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_I2C4>;
+ resets = <&ccu RST_BUS_I2C4>;
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
};
gic: interrupt-controller@1c81000 {
- compatible = "arm,cortex-a7-gic", "arm,cortex-a15-gic";
+ compatible = "arm,gic-400";
reg = <0x01c81000 0x1000>,
<0x01c82000 0x1000>,
<0x01c84000 0x2000>,
<GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
<GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
<GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
- clock-frequency = <24000000>;
- arm,cpu-registers-not-fw-configured;
};
};
projects / platform / kernel / u-boot.git / commitdiff