static void intel_dsi_device_ready(struct intel_encoder *encoder)
{
struct drm_i915_private *dev_priv = encoder->base.dev->dev_private;
- struct intel_crtc *intel_crtc = to_intel_crtc(encoder->base.crtc);
- enum port port = intel_dsi_pipe_to_port(intel_crtc->pipe);
+ struct intel_dsi *intel_dsi = enc_to_intel_dsi(&encoder->base);
+ enum port port;
u32 val;
DRM_DEBUG_KMS("\n");
/* bandgap reset is needed after everytime we do power gate */
band_gap_reset(dev_priv);
- I915_WRITE(MIPI_DEVICE_READY(port), ULPS_STATE_ENTER);
- usleep_range(2500, 3000);
+ for_each_dsi_port(port, intel_dsi->ports) {
- val = I915_READ(MIPI_PORT_CTRL(port));
- I915_WRITE(MIPI_PORT_CTRL(port), val | LP_OUTPUT_HOLD);
- usleep_range(1000, 1500);
+ I915_WRITE(MIPI_DEVICE_READY(port), ULPS_STATE_ENTER);
+ usleep_range(2500, 3000);
- I915_WRITE(MIPI_DEVICE_READY(port), ULPS_STATE_EXIT);
- usleep_range(2500, 3000);
+ val = I915_READ(MIPI_PORT_CTRL(port));
+ I915_WRITE(MIPI_PORT_CTRL(port), val | LP_OUTPUT_HOLD);
+ usleep_range(1000, 1500);
- I915_WRITE(MIPI_DEVICE_READY(port), DEVICE_READY);
- usleep_range(2500, 3000);
+ I915_WRITE(MIPI_DEVICE_READY(port), ULPS_STATE_EXIT);
+ usleep_range(2500, 3000);
+
+ I915_WRITE(MIPI_DEVICE_READY(port), DEVICE_READY);
+ usleep_range(2500, 3000);
+ }
}
static void intel_dsi_enable(struct intel_encoder *encoder)
struct intel_dsi *intel_dsi = enc_to_intel_dsi(encoder);
struct drm_display_mode *adjusted_mode =
&intel_crtc->config.adjusted_mode;
- enum port port = intel_dsi_pipe_to_port(intel_crtc->pipe);
+ enum port port;
unsigned int bpp = intel_crtc->config.pipe_bpp;
u32 val, tmp;
+ u16 mode_hdisplay;
DRM_DEBUG_KMS("pipe %c\n", pipe_name(intel_crtc->pipe));
- /* escape clock divider, 20MHz, shared for A and C. device ready must be
- * off when doing this! txclkesc? */
- tmp = I915_READ(MIPI_CTRL(PORT_A));
- tmp &= ~ESCAPE_CLOCK_DIVIDER_MASK;
- I915_WRITE(MIPI_CTRL(PORT_A), tmp | ESCAPE_CLOCK_DIVIDER_1);
-
- /* read request priority is per pipe */
- tmp = I915_READ(MIPI_CTRL(port));
- tmp &= ~READ_REQUEST_PRIORITY_MASK;
- I915_WRITE(MIPI_CTRL(port), tmp | READ_REQUEST_PRIORITY_HIGH);
+ mode_hdisplay = adjusted_mode->hdisplay;
- /* XXX: why here, why like this? handling in irq handler?! */
- I915_WRITE(MIPI_INTR_STAT(port), 0xffffffff);
- I915_WRITE(MIPI_INTR_EN(port), 0xffffffff);
-
- I915_WRITE(MIPI_DPHY_PARAM(port), intel_dsi->dphy_reg);
+ if (intel_dsi->dual_link) {
+ mode_hdisplay /= 2;
+ if (intel_dsi->dual_link == DSI_DUAL_LINK_FRONT_BACK)
+ mode_hdisplay += intel_dsi->pixel_overlap;
+ }
- I915_WRITE(MIPI_DPI_RESOLUTION(port),
- adjusted_mode->vdisplay << VERTICAL_ADDRESS_SHIFT |
- adjusted_mode->hdisplay << HORIZONTAL_ADDRESS_SHIFT);
+ for_each_dsi_port(port, intel_dsi->ports) {
+ /* escape clock divider, 20MHz, shared for A and C.
+ * device ready must be off when doing this! txclkesc? */
+ tmp = I915_READ(MIPI_CTRL(PORT_A));
+ tmp &= ~ESCAPE_CLOCK_DIVIDER_MASK;
+ I915_WRITE(MIPI_CTRL(PORT_A), tmp | ESCAPE_CLOCK_DIVIDER_1);
+
+ /* read request priority is per pipe */
+ tmp = I915_READ(MIPI_CTRL(port));
+ tmp &= ~READ_REQUEST_PRIORITY_MASK;
+ I915_WRITE(MIPI_CTRL(port), tmp | READ_REQUEST_PRIORITY_HIGH);
+
+ /* XXX: why here, why like this? handling in irq handler?! */
+ I915_WRITE(MIPI_INTR_STAT(port), 0xffffffff);
+ I915_WRITE(MIPI_INTR_EN(port), 0xffffffff);
+
+ I915_WRITE(MIPI_DPHY_PARAM(port), intel_dsi->dphy_reg);
+
+ I915_WRITE(MIPI_DPI_RESOLUTION(port),
+ adjusted_mode->vdisplay << VERTICAL_ADDRESS_SHIFT |
+ mode_hdisplay << HORIZONTAL_ADDRESS_SHIFT);
+ }
set_dsi_timings(encoder, adjusted_mode);
/* XXX: cross-check bpp vs. pixel format? */
val |= intel_dsi->pixel_format;
}
- I915_WRITE(MIPI_DSI_FUNC_PRG(port), val);
- /* timeouts for recovery. one frame IIUC. if counter expires, EOT and
- * stop state. */
-
- /*
- * In burst mode, value greater than one DPI line Time in byte clock
- * (txbyteclkhs) To timeout this timer 1+ of the above said value is
- * recommended.
- *
- * In non-burst mode, Value greater than one DPI frame time in byte
- * clock(txbyteclkhs) To timeout this timer 1+ of the above said value
- * is recommended.
- *
- * In DBI only mode, value greater than one DBI frame time in byte
- * clock(txbyteclkhs) To timeout this timer 1+ of the above said value
- * is recommended.
- */
-
- if (is_vid_mode(intel_dsi) &&
- intel_dsi->video_mode_format == VIDEO_MODE_BURST) {
- I915_WRITE(MIPI_HS_TX_TIMEOUT(port),
- txbyteclkhs(adjusted_mode->htotal, bpp,
- intel_dsi->lane_count,
- intel_dsi->burst_mode_ratio) + 1);
- } else {
- I915_WRITE(MIPI_HS_TX_TIMEOUT(port),
- txbyteclkhs(adjusted_mode->vtotal *
- adjusted_mode->htotal,
- bpp, intel_dsi->lane_count,
- intel_dsi->burst_mode_ratio) + 1);
- }
- I915_WRITE(MIPI_LP_RX_TIMEOUT(port), intel_dsi->lp_rx_timeout);
- I915_WRITE(MIPI_TURN_AROUND_TIMEOUT(port), intel_dsi->turn_arnd_val);
- I915_WRITE(MIPI_DEVICE_RESET_TIMER(port), intel_dsi->rst_timer_val);
+ tmp = 0;
+ if (intel_dsi->eotp_pkt == 0)
+ tmp |= EOT_DISABLE;
+ if (intel_dsi->clock_stop)
+ tmp |= CLOCKSTOP;
- /* dphy stuff */
+ for_each_dsi_port(port, intel_dsi->ports) {
+ I915_WRITE(MIPI_DSI_FUNC_PRG(port), val);
+
+ /* timeouts for recovery. one frame IIUC. if counter expires,
+ * EOT and stop state. */
+
+ /*
+ * In burst mode, value greater than one DPI line Time in byte
+ * clock (txbyteclkhs) To timeout this timer 1+ of the above
+ * said value is recommended.
+ *
+ * In non-burst mode, Value greater than one DPI frame time in
+ * byte clock(txbyteclkhs) To timeout this timer 1+ of the above
+ * said value is recommended.
+ *
+ * In DBI only mode, value greater than one DBI frame time in
+ * byte clock(txbyteclkhs) To timeout this timer 1+ of the above
+ * said value is recommended.
+ */
- /* in terms of low power clock */
- I915_WRITE(MIPI_INIT_COUNT(port), txclkesc(intel_dsi->escape_clk_div, 100));
+ if (is_vid_mode(intel_dsi) &&
+ intel_dsi->video_mode_format == VIDEO_MODE_BURST) {
+ I915_WRITE(MIPI_HS_TX_TIMEOUT(port),
+ txbyteclkhs(adjusted_mode->htotal, bpp,
+ intel_dsi->lane_count,
+ intel_dsi->burst_mode_ratio) + 1);
+ } else {
+ I915_WRITE(MIPI_HS_TX_TIMEOUT(port),
+ txbyteclkhs(adjusted_mode->vtotal *
+ adjusted_mode->htotal,
+ bpp, intel_dsi->lane_count,
+ intel_dsi->burst_mode_ratio) + 1);
+ }
+ I915_WRITE(MIPI_LP_RX_TIMEOUT(port), intel_dsi->lp_rx_timeout);
+ I915_WRITE(MIPI_TURN_AROUND_TIMEOUT(port),
+ intel_dsi->turn_arnd_val);
+ I915_WRITE(MIPI_DEVICE_RESET_TIMER(port),
+ intel_dsi->rst_timer_val);
- val = 0;
- if (intel_dsi->eotp_pkt == 0)
- val |= EOT_DISABLE;
+ /* dphy stuff */
- if (intel_dsi->clock_stop)
- val |= CLOCKSTOP;
+ /* in terms of low power clock */
+ I915_WRITE(MIPI_INIT_COUNT(port),
+ txclkesc(intel_dsi->escape_clk_div, 100));
- /* recovery disables */
- I915_WRITE(MIPI_EOT_DISABLE(port), val);
- /* in terms of low power clock */
- I915_WRITE(MIPI_INIT_COUNT(port), intel_dsi->init_count);
+ /* recovery disables */
+ I915_WRITE(MIPI_EOT_DISABLE(port), val);
- /* in terms of txbyteclkhs. actual high to low switch +
- * MIPI_STOP_STATE_STALL * MIPI_LP_BYTECLK.
- *
- * XXX: write MIPI_STOP_STATE_STALL?
- */
- I915_WRITE(MIPI_HIGH_LOW_SWITCH_COUNT(port),
- intel_dsi->hs_to_lp_count);
+ /* in terms of low power clock */
+ I915_WRITE(MIPI_INIT_COUNT(port), intel_dsi->init_count);
- /* XXX: low power clock equivalence in terms of byte clock. the number
- * of byte clocks occupied in one low power clock. based on txbyteclkhs
- * and txclkesc. txclkesc time / txbyteclk time * (105 +
- * MIPI_STOP_STATE_STALL) / 105.???
- */
- I915_WRITE(MIPI_LP_BYTECLK(port), intel_dsi->lp_byte_clk);
-
- /* the bw essential for transmitting 16 long packets containing 252
- * bytes meant for dcs write memory command is programmed in this
- * register in terms of byte clocks. based on dsi transfer rate and the
- * number of lanes configured the time taken to transmit 16 long packets
- * in a dsi stream varies. */
- I915_WRITE(MIPI_DBI_BW_CTRL(port), intel_dsi->bw_timer);
-
- I915_WRITE(MIPI_CLK_LANE_SWITCH_TIME_CNT(port),
- intel_dsi->clk_lp_to_hs_count << LP_HS_SSW_CNT_SHIFT |
- intel_dsi->clk_hs_to_lp_count << HS_LP_PWR_SW_CNT_SHIFT);
-
- if (is_vid_mode(intel_dsi))
- /* Some panels might have resolution which is not a multiple of
- * 64 like 1366 x 768. Enable RANDOM resolution support for such
- * panels by default */
- I915_WRITE(MIPI_VIDEO_MODE_FORMAT(port),
- intel_dsi->video_frmt_cfg_bits |
- intel_dsi->video_mode_format |
- IP_TG_CONFIG |
- RANDOM_DPI_DISPLAY_RESOLUTION);
+ /* in terms of txbyteclkhs. actual high to low switch +
+ * MIPI_STOP_STATE_STALL * MIPI_LP_BYTECLK.
+ *
+ * XXX: write MIPI_STOP_STATE_STALL?
+ */
+ I915_WRITE(MIPI_HIGH_LOW_SWITCH_COUNT(port),
+ intel_dsi->hs_to_lp_count);
+
+ /* XXX: low power clock equivalence in terms of byte clock.
+ * the number of byte clocks occupied in one low power clock.
+ * based on txbyteclkhs and txclkesc.
+ * txclkesc time / txbyteclk time * (105 + MIPI_STOP_STATE_STALL
+ * ) / 105.???
+ */
+ I915_WRITE(MIPI_LP_BYTECLK(port), intel_dsi->lp_byte_clk);
+
+ /* the bw essential for transmitting 16 long packets containing
+ * 252 bytes meant for dcs write memory command is programmed in
+ * this register in terms of byte clocks. based on dsi transfer
+ * rate and the number of lanes configured the time taken to
+ * transmit 16 long packets in a dsi stream varies. */
+ I915_WRITE(MIPI_DBI_BW_CTRL(port), intel_dsi->bw_timer);
+
+ I915_WRITE(MIPI_CLK_LANE_SWITCH_TIME_CNT(port),
+ intel_dsi->clk_lp_to_hs_count << LP_HS_SSW_CNT_SHIFT |
+ intel_dsi->clk_hs_to_lp_count << HS_LP_PWR_SW_CNT_SHIFT);
+
+ if (is_vid_mode(intel_dsi))
+ /* Some panels might have resolution which is not a
+ * multiple of 64 like 1366 x 768. Enable RANDOM
+ * resolution support for such panels by default */
+ I915_WRITE(MIPI_VIDEO_MODE_FORMAT(port),
+ intel_dsi->video_frmt_cfg_bits |
+ intel_dsi->video_mode_format |
+ IP_TG_CONFIG |
+ RANDOM_DPI_DISPLAY_RESOLUTION);
+ }
}
static void intel_dsi_pre_pll_enable(struct intel_encoder *encoder)
projects / platform / kernel / linux-rpi.git / commitdiff