config SPL_SHARES_INIT_SP_ADDR
bool "SPL and U-Boot use the same initial stack pointer location"
depends on (ARM || ARCH_JZ47XX || MICROBLAZE || RISCV) && SPL_FRAMEWORK
- default n if ARCH_SUNXI
+ default n if ARCH_SUNXI || ARCH_MX6
default y
help
In many cases, we can use the same initial stack pointer address for
hex "Initial stack pointer location"
depends on (ARM || ARCH_JZ47XX || MICROBLAZE || RISCV) && SPL_FRAMEWORK
depends on !SPL_SHARES_INIT_SP_ADDR
+ default 0x93ffb8 if ARCH_MX6 && MX6_OCRAM_256KB
+ default 0x91ffb8 if ARCH_MX6 && !MX6_OCRAM_256KB
help
Address of the start of the stack SPL will use before SDRAM is
initialized.
CONFIG_DISPLAY_BOARDINFO_LATE=y
CONFIG_BOARD_EARLY_INIT_F=y
CONFIG_MISC_INIT_R=y
-# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
-CONFIG_SPL_STACK=0x91ffb8
CONFIG_SPL_DMA=y
CONFIG_SPL_I2C=y
CONFIG_SPL_USB_HOST=y
CONFIG_BOOTCOMMAND="run b_default"
CONFIG_BOARD_EARLY_INIT_F=y
CONFIG_SPL_BOARD_INIT=y
-# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
-CONFIG_SPL_STACK=0x91ffb8
# CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR is not set
CONFIG_SPL_I2C=y
CONFIG_SPL_DM_SPI_FLASH=y
CONFIG_USE_PREBOOT=y
CONFIG_PREBOOT="usb start;sf probe"
CONFIG_MISC_INIT_R=y
-# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
-CONFIG_SPL_STACK=0x91ffb8
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0x80
CONFIG_SPL_I2C=y
CONFIG_SPL_SPI_LOAD=y
CONFIG_DISPLAY_BOARDINFO_LATE=y
CONFIG_BOARD_EARLY_INIT_F=y
CONFIG_MISC_INIT_R=y
-# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
-CONFIG_SPL_STACK=0x91ffb8
CONFIG_SPL_DMA=y
CONFIG_SPL_I2C=y
CONFIG_SPL_USB_HOST=y
CONFIG_BOOTDELAY=3
# CONFIG_USE_BOOTCOMMAND is not set
CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE=y
-# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
-CONFIG_SPL_STACK=0x91ffb8
CONFIG_SPL_SPI_LOAD=y
CONFIG_SYS_SPI_U_BOOT_OFFS=0x11400
CONFIG_SYS_MAXARGS=32
CONFIG_BOOTCOMMAND="if run check_em_pad; then run recovery;else if test ${BOOT_FROM} = FACTORY; then run factory_nfs;else run boot_mmc;fi;fi"
CONFIG_MISC_INIT_R=y
CONFIG_SPL_BOOTCOUNT_LIMIT=y
-# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
-CONFIG_SPL_STACK=0x91ffb8
# CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR is not set
CONFIG_SPL_DMA=y
CONFIG_SPL_ENV_SUPPORT=y
CONFIG_USE_BOOTCOMMAND=y
CONFIG_BOOTCOMMAND="echo SDP Display5 recovery"
CONFIG_MISC_INIT_R=y
-# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
-CONFIG_SPL_STACK=0x91ffb8
# CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR is not set
CONFIG_SPL_DMA=y
CONFIG_SPL_I2C=y
CONFIG_LOG_DEFAULT_LEVEL=4
CONFIG_BOARD_EARLY_INIT_F=y
CONFIG_MISC_INIT_R=y
-# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
-CONFIG_SPL_STACK=0x91ffb8
CONFIG_SPL_SPI_LOAD=y
CONFIG_SYS_SPI_U_BOOT_OFFS=0x11400
CONFIG_SPL_USB_HOST=y
CONFIG_MISC_INIT_R=y
CONFIG_PCI_INIT_R=y
CONFIG_SPL_BOARD_INIT=y
-# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
-CONFIG_SPL_STACK=0x91ffb8
CONFIG_SPL_STACK_R=y
CONFIG_SPL_FIT_IMAGE_TINY=y
CONFIG_SPL_DMA=y
CONFIG_MISC_INIT_R=y
CONFIG_PCI_INIT_R=y
CONFIG_SPL_BOARD_INIT=y
-# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
-CONFIG_SPL_STACK=0x91ffb8
CONFIG_SPL_STACK_R=y
CONFIG_SPL_FIT_IMAGE_TINY=y
CONFIG_SPL_DMA=y
CONFIG_MISC_INIT_R=y
CONFIG_PCI_INIT_R=y
CONFIG_SPL_BOARD_INIT=y
-# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
-CONFIG_SPL_STACK=0x91ffb8
CONFIG_SPL_STACK_R=y
CONFIG_SPL_FIT_IMAGE_TINY=y
CONFIG_SPL_DMA=y
CONFIG_BOOTDELAY=3
CONFIG_USE_BOOTCOMMAND=y
CONFIG_BOOTCOMMAND="run $modeboot"
-# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
-CONFIG_SPL_STACK=0x91ffb8
CONFIG_SPL_DMA=y
CONFIG_SPL_NAND_SUPPORT=y
CONFIG_SPL_WATCHDOG=y
CONFIG_LTO=y
CONFIG_DISTRO_DEFAULTS=y
CONFIG_BOOTDELAY=3
-# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
-CONFIG_SPL_STACK=0x91ffb8
CONFIG_SPL_OS_BOOT=y
CONFIG_SPL_FALCON_BOOT_MMCSD=y
CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR=0x1000
CONFIG_BOOTCOMMAND="run mmc_mmc_fit"
CONFIG_SPL_BOARD_INIT=y
CONFIG_SPL_RAW_IMAGE_SUPPORT=y
-# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
-CONFIG_SPL_STACK=0x91ffb8
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0xaa
# CONFIG_SPL_CRC32 is not set
# CONFIG_SPL_CRYPTO is not set
CONFIG_BOOTDELAY=3
CONFIG_USE_BOOTCOMMAND=y
CONFIG_BOOTCOMMAND="run $modeboot"
-# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
-CONFIG_SPL_STACK=0x91ffb8
CONFIG_SPL_DMA=y
CONFIG_SPL_NAND_SUPPORT=y
CONFIG_SPL_WATCHDOG=y
CONFIG_SYS_CONSOLE_IS_IN_ENV=y
CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE=y
CONFIG_SPL_RAW_IMAGE_SUPPORT=y
-# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
-CONFIG_SPL_STACK=0x93ffb8
# CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR is not set
CONFIG_SPL_DMA=y
CONFIG_SPL_FS_LOAD_PAYLOAD_NAME="u-boot-dtb.img"
CONFIG_USE_BOOTCOMMAND=y
CONFIG_BOOTCOMMAND="run $modeboot"
CONFIG_SPL_RAW_IMAGE_SUPPORT=y
-# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
-CONFIG_SPL_STACK=0x91ffb8
CONFIG_SPL_OS_BOOT=y
CONFIG_SPL_FALCON_BOOT_MMCSD=y
CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR=0x1000
CONFIG_USE_BOOTCOMMAND=y
CONFIG_BOOTCOMMAND="run $modeboot"
CONFIG_SPL_RAW_IMAGE_SUPPORT=y
-# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
-CONFIG_SPL_STACK=0x91ffb8
CONFIG_SPL_OS_BOOT=y
CONFIG_SPL_FALCON_BOOT_MMCSD=y
CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR=0x1000
CONFIG_BOOTDELAY=3
CONFIG_USE_BOOTCOMMAND=y
CONFIG_BOOTCOMMAND="run $modeboot"
-# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
-CONFIG_SPL_STACK=0x91ffb8
CONFIG_SPL_DMA=y
CONFIG_SPL_NAND_SUPPORT=y
CONFIG_SPL_WATCHDOG=y
CONFIG_USE_BOOTCOMMAND=y
CONFIG_BOOTCOMMAND="run $modeboot"
CONFIG_SPL_RAW_IMAGE_SUPPORT=y
-# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
-CONFIG_SPL_STACK=0x91ffb8
CONFIG_SPL_OS_BOOT=y
CONFIG_SPL_FALCON_BOOT_MMCSD=y
CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR=0x1000
CONFIG_USE_BOOTCOMMAND=y
CONFIG_BOOTCOMMAND="run $modeboot"
CONFIG_SPL_RAW_IMAGE_SUPPORT=y
-# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
-CONFIG_SPL_STACK=0x91ffb8
CONFIG_SPL_WATCHDOG=y
CONFIG_HUSH_PARSER=y
CONFIG_SYS_PROMPT="geam6ul> "
CONFIG_BOOTDELAY=3
CONFIG_USE_BOOTCOMMAND=y
CONFIG_BOOTCOMMAND="run $modeboot"
-# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
-CONFIG_SPL_STACK=0x91ffb8
CONFIG_SPL_DMA=y
CONFIG_SPL_NAND_SUPPORT=y
CONFIG_SPL_WATCHDOG=y
CONFIG_USE_BOOTCOMMAND=y
CONFIG_BOOTCOMMAND="run $modeboot"
CONFIG_SPL_RAW_IMAGE_SUPPORT=y
-# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
-CONFIG_SPL_STACK=0x91ffb8
CONFIG_SPL_WATCHDOG=y
CONFIG_HUSH_PARSER=y
CONFIG_SYS_PROMPT="isiotmx6ul> "
CONFIG_BOOTDELAY=3
CONFIG_USE_BOOTCOMMAND=y
CONFIG_BOOTCOMMAND="run $modeboot"
-# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
-CONFIG_SPL_STACK=0x91ffb8
CONFIG_SPL_DMA=y
CONFIG_SPL_NAND_SUPPORT=y
CONFIG_SPL_WATCHDOG=y
CONFIG_BOARD_EARLY_INIT_F=y
CONFIG_SPL_LEGACY_IMAGE_FORMAT=y
CONFIG_SPL_LEGACY_IMAGE_CRC_CHECK=y
-# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
-CONFIG_SPL_STACK=0x91ffb8
CONFIG_SPL_USB_HOST=y
CONFIG_SPL_USB_GADGET=y
CONFIG_SPL_WATCHDOG=y
# CONFIG_USE_BOOTCOMMAND is not set
CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE=y
CONFIG_SPL_RAW_IMAGE_SUPPORT=y
-# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
-CONFIG_SPL_STACK=0x91ffb8
CONFIG_SPL_POWER=y
CONFIG_SPL_WATCHDOG=y
CONFIG_SYS_MAXARGS=32
CONFIG_BOOTCOMMAND="mmc dev ${mmcdev};if mmc rescan; then if run loadbootscript; then run bootscript; else if run loadimage; then run mmcboot; else run netboot; fi; fi; else run netboot; fi"
CONFIG_DEFAULT_FDT_FILE="imx6ul-liteboard.dtb"
CONFIG_BOARD_EARLY_INIT_F=y
-# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
-CONFIG_SPL_STACK=0x91ffb8
CONFIG_SPL_WATCHDOG=y
CONFIG_HUSH_PARSER=y
CONFIG_SYS_MAXARGS=32
# CONFIG_USE_BOOTCOMMAND is not set
CONFIG_BOARD_LATE_INIT=y
CONFIG_SPL_BOARD_INIT=y
-# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
-CONFIG_SPL_STACK=0x91ffb8
CONFIG_SPL_FIT_IMAGE_TINY=y
CONFIG_SPL_ENV_SUPPORT=y
CONFIG_SPL_NOR_SUPPORT=y
# CONFIG_USE_BOOTCOMMAND is not set
CONFIG_BOARD_LATE_INIT=y
CONFIG_SPL_BOARD_INIT=y
-# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
-CONFIG_SPL_STACK=0x91ffb8
CONFIG_SPL_ENV_SUPPORT=y
CONFIG_SPL_NOR_SUPPORT=y
CONFIG_SYS_MAXARGS=32
CONFIG_USE_PREBOOT=y
CONFIG_PREBOOT="if hdmidet; then usb start; setenv stdin serial,usbkbd; setenv stdout serial,vidconsole; setenv stderr serial,vidconsole; else setenv stdin serial; setenv stdout serial; setenv stderr serial; fi;"
CONFIG_BOARD_EARLY_INIT_F=y
-# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
-CONFIG_SPL_STACK=0x91ffb8
CONFIG_SPL_FS_EXT4=y
CONFIG_SPL_FS_LOAD_PAYLOAD_NAME="u-boot-dtb.img"
CONFIG_SPL_I2C=y
CONFIG_SYS_MEMTEST_START=0x10000000
CONFIG_SYS_MEMTEST_END=0x20000000
CONFIG_SUPPORT_RAW_INITRD=y
-# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
-CONFIG_SPL_STACK=0x91ffb8
CONFIG_SPL_USB_HOST=y
CONFIG_SPL_WATCHDOG=y
CONFIG_HUSH_PARSER=y
CONFIG_SYS_CONSOLE_IS_IN_ENV=y
CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE=y
CONFIG_SPL_LEGACY_IMAGE_FORMAT=y
-# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
-CONFIG_SPL_STACK=0x91ffb8
CONFIG_SPL_FIT_IMAGE_TINY=y
CONFIG_SPL_FS_EXT4=y
CONFIG_SPL_FS_LOAD_PAYLOAD_NAME="u-boot-dtb.img"
CONFIG_SYS_CONSOLE_IS_IN_ENV=y
CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE=y
CONFIG_SPL_LEGACY_IMAGE_FORMAT=y
-# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
-CONFIG_SPL_STACK=0x91ffb8
CONFIG_SPL_FIT_IMAGE_TINY=y
CONFIG_SPL_USB_HOST=y
CONFIG_SPL_USB_GADGET=y
CONFIG_USE_BOOTCOMMAND=y
CONFIG_BOOTCOMMAND="mmc dev ${mmcdev}; if mmc rescan; then if run loadbootscript; then run bootscript; else if run loadimage; then run mmcboot; else run netboot; fi; fi; else run netboot; fi"
CONFIG_BOARD_EARLY_INIT_F=y
-# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
-CONFIG_SPL_STACK=0x91ffb8
CONFIG_SPL_FS_EXT4=y
CONFIG_SPL_FS_LOAD_PAYLOAD_NAME="u-boot-dtb.img"
CONFIG_SPL_I2C=y
# CONFIG_CONSOLE_MUX is not set
CONFIG_SYS_CONSOLE_IS_IN_ENV=y
CONFIG_BOARD_EARLY_INIT_F=y
-# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
-CONFIG_SPL_STACK=0x91ffb8
CONFIG_SPL_FS_EXT4=y
CONFIG_SPL_FS_LOAD_PAYLOAD_NAME="u-boot-dtb.img"
CONFIG_SPL_I2C=y
# CONFIG_CONSOLE_MUX is not set
CONFIG_SYS_CONSOLE_IS_IN_ENV=y
CONFIG_BOARD_EARLY_INIT_F=y
-# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
-CONFIG_SPL_STACK=0x91ffb8
CONFIG_SPL_FS_EXT4=y
CONFIG_SPL_FS_LOAD_PAYLOAD_NAME="u-boot-dtb.img"
CONFIG_SPL_I2C=y
CONFIG_FIT=y
CONFIG_BOOTDELAY=3
CONFIG_BOARD_EARLY_INIT_F=y
-# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
-CONFIG_SPL_STACK=0x91ffb8
CONFIG_SPL_DMA=y
CONFIG_SPL_NAND_SUPPORT=y
CONFIG_SPL_USB_HOST=y
CONFIG_BOOTCOMMAND="run distro_bootcmd ; run net_nfs"
CONFIG_BOARD_EARLY_INIT_F=y
CONFIG_MISC_INIT_R=y
-# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
-CONFIG_SPL_STACK=0x91ffb8
CONFIG_SPL_FS_EXT4=y
CONFIG_SPL_FS_LOAD_PAYLOAD_NAME="u-boot-dtb.img"
CONFIG_SPL_I2C=y
# CONFIG_CONSOLE_MUX is not set
CONFIG_SYS_CONSOLE_IS_IN_ENV=y
CONFIG_SPL_BOARD_INIT=y
-# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
-CONFIG_SPL_STACK=0x91ffb8
CONFIG_SPL_ENV_SUPPORT=y
CONFIG_SPL_WATCHDOG=y
CONFIG_SPL_YMODEM_SUPPORT=y
CONFIG_BOOTCOMMAND="run mmcboot;run nandboot"
CONFIG_DISPLAY_BOARDINFO_LATE=y
CONFIG_SPL_BOARD_INIT=y
-# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
-CONFIG_SPL_STACK=0x93ffb8
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0x18a
CONFIG_SPL_DMA=y
CONFIG_SPL_FS_EXT4=y
CONFIG_DISTRO_DEFAULTS=y
CONFIG_BOOTDELAY=3
CONFIG_BOARD_EARLY_INIT_F=y
-# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
-CONFIG_SPL_STACK=0x91ffb8
CONFIG_SPL_USB_HOST=y
CONFIG_SPL_WATCHDOG=y
CONFIG_SYS_MAXARGS=32
CONFIG_BOOTDELAY=3
CONFIG_BOOTCOMMAND="run mmc_mmc_fit"
CONFIG_BOARD_EARLY_INIT_F=y
-# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
-CONFIG_SPL_STACK=0x91ffb8
CONFIG_SPL_USB_HOST=y
CONFIG_SPL_WATCHDOG=y
CONFIG_SYS_MAXARGS=32
CONFIG_BOOTCOMMAND="run findfdt; run finduuid; run distro_bootcmd"
CONFIG_DEFAULT_FDT_FILE="imx6ul-pico-dwarf.dtb"
CONFIG_BOARD_EARLY_INIT_F=y
-# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
-CONFIG_SPL_STACK=0x91ffb8
CONFIG_SPL_USB_HOST=y
CONFIG_SPL_USB_GADGET=y
CONFIG_SPL_USB_SDP_SUPPORT=y
CONFIG_BOOTCOMMAND="run findfdt; run finduuid; run distro_bootcmd"
CONFIG_DEFAULT_FDT_FILE="imx6ul-pico-hobbit.dtb"
CONFIG_BOARD_EARLY_INIT_F=y
-# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
-CONFIG_SPL_STACK=0x91ffb8
CONFIG_SPL_USB_HOST=y
CONFIG_SPL_USB_GADGET=y
CONFIG_SPL_USB_SDP_SUPPORT=y
CONFIG_BOOTCOMMAND="run default_boot"
CONFIG_DEFAULT_FDT_FILE="ask"
CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE=y
-# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
-CONFIG_SPL_STACK=0x91ffb8
CONFIG_SPL_FIT_IMAGE_TINY=y
CONFIG_SPL_FS_EXT4=y
CONFIG_SPL_FS_LOAD_PAYLOAD_NAME="u-boot-dtb.img"
CONFIG_BOOTCOMMAND="run findfdt; run finduuid; run distro_bootcmd"
CONFIG_DEFAULT_FDT_FILE="ask"
CONFIG_BOARD_EARLY_INIT_F=y
-# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
-CONFIG_SPL_STACK=0x91ffb8
CONFIG_SPL_USB_HOST=y
CONFIG_SPL_USB_GADGET=y
CONFIG_SPL_USB_SDP_SUPPORT=y
CONFIG_BOOTCOMMAND="run findfdt; run finduuid; run distro_bootcmd"
CONFIG_DEFAULT_FDT_FILE="imx6ul-pico-pi.dtb"
CONFIG_BOARD_EARLY_INIT_F=y
-# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
-CONFIG_SPL_STACK=0x91ffb8
CONFIG_SPL_USB_HOST=y
CONFIG_SPL_USB_GADGET=y
CONFIG_SPL_USB_SDP_SUPPORT=y
CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE=y
CONFIG_BOARD_EARLY_INIT_F=y
CONFIG_SPL_RAW_IMAGE_SUPPORT=y
-# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
-CONFIG_SPL_STACK=0x91ffb8
CONFIG_SPL_FS_EXT4=y
CONFIG_SPL_FS_LOAD_PAYLOAD_NAME="u-boot-dtb.img"
CONFIG_SPL_FS_LOAD_ARGS_NAME="imx6dl-riotboard.dtb"
CONFIG_FIT=y
CONFIG_BOOTDELAY=3
CONFIG_BOARD_EARLY_INIT_F=y
-# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
-CONFIG_SPL_STACK=0x91ffb8
CONFIG_SPL_DMA=y
CONFIG_SPL_NAND_SUPPORT=y
CONFIG_SPL_USB_HOST=y
CONFIG_BOOTDELAY=3
CONFIG_BOOTCOMMAND="run findfdt; run distro_bootcmd"
CONFIG_BOARD_EARLY_INIT_F=y
-# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
-CONFIG_SPL_STACK=0x91ffb8
CONFIG_SPL_FS_EXT4=y
CONFIG_SPL_FS_LOAD_PAYLOAD_NAME="u-boot-dtb.img"
CONFIG_SPL_I2C=y
CONFIG_DISTRO_DEFAULTS=y
CONFIG_BOOTCOMMAND="run findfdt; run distro_bootcmd"
CONFIG_BOARD_EARLY_INIT_F=y
-# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
-CONFIG_SPL_STACK=0x91ffb8
CONFIG_SPL_ENV_SUPPORT=y
CONFIG_SPL_FS_EXT4=y
CONFIG_SPL_FS_LOAD_PAYLOAD_NAME="u-boot-dtb.img"
CONFIG_FIT=y
CONFIG_BOOTDELAY=3
CONFIG_BOOTCOMMAND="run mmc_mmc_fit"
-# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
-CONFIG_SPL_STACK=0x91ffb8
CONFIG_SPL_USB_HOST=y
CONFIG_SPL_WATCHDOG=y
CONFIG_SYS_MAXARGS=32
CONFIG_BOOTCOMMAND="run distro_bootcmd"
CONFIG_SYS_CONSOLE_IS_IN_ENV=y
CONFIG_BOARD_EARLY_INIT_F=y
-# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
-CONFIG_SPL_STACK=0x91ffb8
CONFIG_SPL_FS_EXT4=y
CONFIG_SPL_FS_LOAD_PAYLOAD_NAME="u-boot-dtb.img"
CONFIG_SPL_I2C=y
CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE=y
# CONFIG_DISPLAY_BOARDINFO is not set
CONFIG_BOARD_EARLY_INIT_F=y
-# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
-CONFIG_SPL_STACK=0x91ffb8
CONFIG_SPL_FIT_IMAGE_TINY=y
CONFIG_SPL_FS_EXT4=y
CONFIG_SPL_FS_LOAD_PAYLOAD_NAME="u-boot-dtb.img"
NAND write: device 0 offset 0x200000, size 0x8fd26
589094 bytes written: OK
icorem6qdl>
+
+SPL Stack size and location notes
+---------------------------------
+
+If we have CONFIG_MX6_OCRAM_256KB then see Figure 8.4.1 in IMX6DQ Reference
+manuals:
+ - IMX6DQ OCRAM (IRAM) is from 0x00907000 to 0x0093FFFF
+ - BOOT ROM stack is at 0x0093FFB8
+ - if icache/dcache is enabled (eFuse/strapping controlled) then the
+ IMX BOOT ROM will setup MMU table at 0x00938000, therefore we need to
+ fit between 0x00907000 and 0x00938000.
+ - Additionally the BOOT ROM loads what they consider the firmware image
+ which consists of a 4K header in front of us that contains the IVT, DCD
+ and some padding thus 'our' max size is really 0x00908000 - 0x00938000
+ or 192KB
+ - Pad SPL to 196KB (4KB header + 192KB max size). This allows to write the
+ SPL/U-Boot combination generated with u-boot-with-spl.imx directly to a
+ boot media (given that boot media specific offset is configured properly).
+and if we don't, see Figure 8-3 in IMX6SDL Reference manuals:
+ - IMX6SDL OCRAM (IRAM) is from 0x00907000 to 0x0091FFFF
+ - BOOT ROM stack is at 0x0091FFB8
+ - if icache/dcache is enabled (eFuse/strapping controlled) then the
+ IMX BOOT ROM will setup MMU table at 0x00918000, therefore we need to
+ fit between 0x00907000 and 0x00918000.
+ - Additionally the BOOT ROM loads what they consider the firmware image
+ which consists of a 4K header in front of us that contains the IVT, DCD
+ and some padding thus 'our' max size is really 0x00908000 - 0x00918000
+ or 64KB
+ - Pad SPL to 68KB (4KB header + 64KB max size). This allows to write the
+ SPL/U-Boot combination generated with u-boot-with-spl.imx directly to a
+ boot media (given that boot media specific offset is configured properly).
#ifdef CONFIG_SPL
-#ifdef CONFIG_MX6_OCRAM_256KB
-/*
- * see Figure 8.4.1 in IMX6DQ Reference manuals:
- * - IMX6DQ OCRAM (IRAM) is from 0x00907000 to 0x0093FFFF
- * - BOOT ROM stack is at 0x0093FFB8
- * - if icache/dcache is enabled (eFuse/strapping controlled) then the
- * IMX BOOT ROM will setup MMU table at 0x00938000, therefore we need to
- * fit between 0x00907000 and 0x00938000.
- * - Additionally the BOOT ROM loads what they consider the firmware image
- * which consists of a 4K header in front of us that contains the IVT, DCD
- * and some padding thus 'our' max size is really 0x00908000 - 0x00938000
- * or 192KB
- */
-/*
- * Pad SPL to 196KB (4KB header + 192KB max size). This allows to write the
- * SPL/U-Boot combination generated with u-boot-with-spl.imx directly to a
- * boot media (given that boot media specific offset is configured properly).
- */
-#else
-/*
- * see Figure 8-3 in IMX6SDL Reference manuals:
- * - IMX6SDL OCRAM (IRAM) is from 0x00907000 to 0x0091FFFF
- * - BOOT ROM stack is at 0x0091FFB8
- * - if icache/dcache is enabled (eFuse/strapping controlled) then the
- * IMX BOOT ROM will setup MMU table at 0x00918000, therefore we need to
- * fit between 0x00907000 and 0x00918000.
- * - Additionally the BOOT ROM loads what they consider the firmware image
- * which consists of a 4K header in front of us that contains the IVT, DCD
- * and some padding thus 'our' max size is really 0x00908000 - 0x00918000
- * or 64KB
- */
-/*
- * Pad SPL to 68KB (4KB header + 64KB max size). This allows to write the
- * SPL/U-Boot combination generated with u-boot-with-spl.imx directly to a
- * boot media (given that boot media specific offset is configured properly).
- */
-
-#endif
-
/* MMC support */
#if defined(CONFIG_SPL_MMC)
#define CONFIG_SYS_MONITOR_LEN 409600 /* 400 KB */