extern void lh7a400_init_irq (void);
extern void lh7a404_init_irq (void);
+extern void lh7a40x_clcd_init (void);
extern void lh7a40x_init_board_irq (void);
#define IRQ_DISPATCH(irq) desc_handle_irq((irq),(irq_desc + irq), regs)
--- /dev/null
+/* lcd-panel.h
+ $Id$
+
+ written by Marc Singer
+ 18 Jul 2005
+
+ Copyright (C) 2005 Marc Singer
+
+ -----------
+ DESCRIPTION
+ -----------
+
+ Only one panel may be defined at a time.
+
+ The pixel clock is calculated to be no greater than the target.
+
+ Each timing value is accompanied by a specification comment.
+
+ UNITS/MIN/TYP/MAX
+
+ Most of the units will be in clocks.
+
+ USE_RGB555
+
+ Define this macro to configure the AMBA LCD controller to use an
+ RGB555 encoding for the pels instead of the normal RGB565.
+
+ LPD9520, LPD79524, LPD7A400, LPD7A404-10, LPD7A404-11
+
+ These boards are best approximated by 555 for all panels. Some
+ can use an extra low-order bit of blue in bit 16 of the color
+ value, but we don't have a way to communicate this non-linear
+ mapping to the kernel.
+
+*/
+
+#if !defined (__LCD_PANEL_H__)
+# define __LCD_PANEL_H__
+
+#if defined (MACH_LPD79520)\
+ || defined (MACH_LPD79524)\
+ || defined (MACH_LPD7A400)\
+ || defined (MACH_LPD7A404)
+# define USE_RGB555
+#endif
+
+struct clcd_panel_extra {
+ unsigned int hrmode;
+ unsigned int clsen;
+ unsigned int spsen;
+ unsigned int pcdel;
+ unsigned int revdel;
+ unsigned int lpdel;
+ unsigned int spldel;
+ unsigned int pc2del;
+};
+
+#define NS_TO_CLOCK(ns,c) ((((ns)*((c)/1000) + (1000000 - 1))/1000000))
+#define CLOCK_TO_DIV(e,c) (((c) + (e) - 1)/(e))
+
+#if defined CONFIG_FB_ARMCLCD_SHARP_LQ035Q7DB02_HRTFT
+
+ /* Logic Product Development LCD 3.5" QVGA HRTFT -10 */
+ /* Sharp PN LQ035Q7DB02 w/HRTFT controller chip */
+
+#define PIX_CLOCK_TARGET (6800000)
+#define PIX_CLOCK_DIVIDER CLOCK_TO_DIV (PIX_CLOCK_TARGET, HCLK)
+#define PIX_CLOCK (HCLK/PIX_CLOCK_DIVIDER)
+
+static struct clcd_panel lcd_panel = {
+ .mode = {
+ .name = "3.5in QVGA (LQ035Q7DB02)",
+ .xres = 240,
+ .yres = 320,
+ .pixclock = PIX_CLOCK,
+ .left_margin = 16,
+ .right_margin = 21,
+ .upper_margin = 8, // line/8/8/8
+ .lower_margin = 5,
+ .hsync_len = 61,
+ .vsync_len = NS_TO_CLOCK (60, PIX_CLOCK),
+ .vmode = FB_VMODE_NONINTERLACED,
+ },
+ .width = -1,
+ .height = -1,
+ .tim2 = TIM2_IPC | (PIX_CLOCK_DIVIDER - 2),
+ .cntl = CNTL_LCDTFT | CNTL_WATERMARK,
+ .bpp = 16,
+};
+
+#define HAS_LCD_PANEL_EXTRA
+
+static struct clcd_panel_extra lcd_panel_extra = {
+ .hrmode = 1,
+ .clsen = 1,
+ .spsen = 1,
+ .pcdel = 8,
+ .revdel = 7,
+ .lpdel = 13,
+ .spldel = 77,
+ .pc2del = 208,
+};
+
+#endif
+
+#if defined CONFIG_FB_ARMCLCD_SHARP_LQ057Q3DC02
+
+ /* Logic Product Development LCD 5.7" QVGA -10 */
+ /* Sharp PN LQ057Q3DC02 */
+ /* QVGA mode, V/Q=LOW */
+
+/* From Sharp on 2006.1.3. I believe some of the values are incorrect
+ * based on the datasheet.
+
+ Timing0 TIMING1 TIMING2 CONTROL
+ 0x140A0C4C 0x080504EF 0x013F380D 0x00000829
+ HBP= 20 VBP= 8 BCD= 0
+ HFP= 10 VFP= 5 CPL=319
+ HSW= 12 VSW= 1 IOE= 0
+ PPL= 19 LPP=239 IPC= 1
+ IHS= 1
+ IVS= 1
+ ACB= 0
+ CSEL= 0
+ PCD= 13
+
+ */
+
+/* The full horozontal cycle (Th) is clock/360/400/450. */
+/* The full vertical cycle (Tv) is line/251/262/280. */
+
+#define PIX_CLOCK_TARGET (6300000) /* -/6.3/7 MHz */
+#define PIX_CLOCK_DIVIDER CLOCK_TO_DIV (PIX_CLOCK_TARGET, HCLK)
+#define PIX_CLOCK (HCLK/PIX_CLOCK_DIVIDER)
+
+static struct clcd_panel lcd_panel = {
+ .mode = {
+ .name = "5.7in QVGA (LQ057Q3DC02)",
+ .xres = 320,
+ .yres = 240,
+ .pixclock = PIX_CLOCK,
+ .left_margin = 11,
+ .right_margin = 400-11-320-2,
+ .upper_margin = 7, // line/7/7/7
+ .lower_margin = 262-7-240-2,
+ .hsync_len = 2, // clk/2/96/200
+ .vsync_len = 2, // line/2/-/34
+ .vmode = FB_VMODE_NONINTERLACED,
+ },
+ .width = -1,
+ .height = -1,
+ .tim2 = TIM2_IHS | TIM2_IVS
+ | (PIX_CLOCK_DIVIDER - 2),
+ .cntl = CNTL_LCDTFT | CNTL_WATERMARK,
+ .bpp = 16,
+};
+
+#endif
+
+#if defined CONFIG_FB_ARMCLCD_SHARP_LQ64D343
+
+ /* Logic Product Development LCD 6.4" VGA -10 */
+ /* Sharp PN LQ64D343 */
+
+/* The full horozontal cycle (Th) is clock/750/800/900. */
+/* The full vertical cycle (Tv) is line/515/525/560. */
+
+#define PIX_CLOCK_TARGET (28330000)
+#define PIX_CLOCK_DIVIDER CLOCK_TO_DIV (PIX_CLOCK_TARGET, HCLK)
+#define PIX_CLOCK (HCLK/PIX_CLOCK_DIVIDER)
+
+static struct clcd_panel lcd_panel = {
+ .mode = {
+ .name = "6.4in QVGA (LQ64D343)",
+ .xres = 640,
+ .yres = 480,
+ .pixclock = PIX_CLOCK,
+ .left_margin = 32,
+ .right_margin = 800-32-640-96,
+ .upper_margin = 32, // line/34/34/34
+ .lower_margin = 540-32-480-2,
+ .hsync_len = 96, // clk/2/96/200
+ .vsync_len = 2, // line/2/-/34
+ .vmode = FB_VMODE_NONINTERLACED,
+ },
+ .width = -1,
+ .height = -1,
+ .tim2 = TIM2_IHS | TIM2_IVS
+ | (PIX_CLOCK_DIVIDER - 2),
+ .cntl = CNTL_LCDTFT | CNTL_WATERMARK,
+ .bpp = 16,
+};
+
+#endif
+
+#if defined CONFIG_FB_ARMCLCD_SHARP_LQ10D368
+
+ /* Logic Product Development LCD 10.4" VGA -10 */
+ /* Sharp PN LQ10D368 */
+
+#define PIX_CLOCK_TARGET (28330000)
+#define PIX_CLOCK_DIVIDER CLOCK_TO_DIV (PIX_CLOCK_TARGET, HCLK)
+#define PIX_CLOCK (HCLK/PIX_CLOCK_DIVIDER)
+
+static struct clcd_panel lcd_panel = {
+ .mode = {
+ .name = "10.4in VGA (LQ10D368)",
+ .xres = 640,
+ .yres = 480,
+ .pixclock = PIX_CLOCK,
+ .left_margin = 21,
+ .right_margin = 15,
+ .upper_margin = 34,
+ .lower_margin = 5,
+ .hsync_len = 96,
+ .vsync_len = 16,
+ .vmode = FB_VMODE_NONINTERLACED,
+ },
+ .width = -1,
+ .height = -1,
+ .tim2 = TIM2_IHS | TIM2_IVS
+ | (PIX_CLOCK_DIVIDER - 2),
+ .cntl = CNTL_LCDTFT | CNTL_WATERMARK,
+ .bpp = 16,
+};
+
+#endif
+
+#if defined CONFIG_FB_ARMCLCD_SHARP_LQ121S1DG41
+
+ /* Logic Product Development LCD 12.1" SVGA -10 */
+ /* Sharp PN LQ121S1DG41, was LQ121S1DG31 */
+
+/* Note that with a 99993900 Hz HCLK, it is not possible to hit the
+ * target clock frequency range of 35MHz to 42MHz. */
+
+/* If the target pixel clock is substantially lower than the panel
+ * spec, this is done to prevent the LCD display from glitching when
+ * the CPU is under load. A pixel clock higher than 25MHz
+ * (empirically determined) will compete with the CPU for bus cycles
+ * for the Ethernet chip. However, even a pixel clock of 10MHz
+ * competes with Compact Flash interface during some operations
+ * (fdisk, e2fsck). And, at that speed the display may have a visible
+ * flicker. */
+
+/* The full horozontal cycle (Th) is clock/832/1056/1395. */
+
+#define PIX_CLOCK_TARGET (20000000)
+#define PIX_CLOCK_DIVIDER CLOCK_TO_DIV (PIX_CLOCK_TARGET, HCLK)
+#define PIX_CLOCK (HCLK/PIX_CLOCK_DIVIDER)
+
+static struct clcd_panel lcd_panel = {
+ .mode = {
+ .name = "12.1in SVGA (LQ121S1DG41)",
+ .xres = 800,
+ .yres = 600,
+ .pixclock = PIX_CLOCK,
+ .left_margin = 89, // ns/5/-/(1/PIX_CLOCK)-10
+ .right_margin = 1056-800-89-128,
+ .upper_margin = 23, // line/23/23/23
+ .lower_margin = 44,
+ .hsync_len = 128, // clk/2/128/200
+ .vsync_len = 4, // line/2/4/6
+ .vmode = FB_VMODE_NONINTERLACED,
+ },
+ .width = -1,
+ .height = -1,
+ .tim2 = TIM2_IHS | TIM2_IVS
+ | (PIX_CLOCK_DIVIDER - 2),
+ .cntl = CNTL_LCDTFT | CNTL_WATERMARK,
+ .bpp = 16,
+};
+
+#endif
+
+#if defined CONFIG_FB_ARMCLCD_HITACHI
+
+ /* Hitachi*/
+ /* Submitted by Michele Da Rold <michele.darold@ecsproject.com> */
+
+#define PIX_CLOCK_TARGET (49000000)
+#define PIX_CLOCK_DIVIDER CLOCK_TO_DIV (PIX_CLOCK_TARGET, HCLK)
+#define PIX_CLOCK (HCLK/PIX_CLOCK_DIVIDER)
+
+static struct clcd_panel lcd_panel = {
+ .mode = {
+ .name = "Hitachi 800x480",
+ .xres = 800,
+ .yres = 480,
+ .pixclock = PIX_CLOCK,
+ .left_margin = 88,
+ .right_margin = 40,
+ .upper_margin = 32,
+ .lower_margin = 11,
+ .hsync_len = 128,
+ .vsync_len = 2,
+ .vmode = FB_VMODE_NONINTERLACED,
+ },
+ .width = -1,
+ .height = -1,
+ .tim2 = TIM2_IPC | TIM2_IHS | TIM2_IVS
+ | (PIX_CLOCK_DIVIDER - 2),
+ .cntl = CNTL_LCDTFT | CNTL_WATERMARK,
+ .bpp = 16,
+};
+
+#endif
+
+
+#if defined CONFIG_FB_ARMCLCD_AUO_A070VW01_WIDE
+
+ /* AU Optotronics A070VW01 7.0 Wide Screen color Display*/
+ /* Submitted by Michele Da Rold <michele.darold@ecsproject.com> */
+
+#define PIX_CLOCK_TARGET (10000000)
+#define PIX_CLOCK_DIVIDER CLOCK_TO_DIV (PIX_CLOCK_TARGET, HCLK)
+#define PIX_CLOCK (HCLK/PIX_CLOCK_DIVIDER)
+
+static struct clcd_panel lcd_panel = {
+ .mode = {
+ .name = "7.0in Wide (A070VW01)",
+ .xres = 480,
+ .yres = 234,
+ .pixclock = PIX_CLOCK,
+ .left_margin = 30,
+ .right_margin = 25,
+ .upper_margin = 14,
+ .lower_margin = 12,
+ .hsync_len = 100,
+ .vsync_len = 1,
+ .vmode = FB_VMODE_NONINTERLACED,
+ },
+ .width = -1,
+ .height = -1,
+ .tim2 = TIM2_IPC | TIM2_IHS | TIM2_IVS
+ | (PIX_CLOCK_DIVIDER - 2),
+ .cntl = CNTL_LCDTFT | CNTL_WATERMARK,
+ .bpp = 16,
+};
+
+#endif
+
+#undef NS_TO_CLOCK
+#undef CLOCK_TO_DIV
+
+#endif /* __LCD_PANEL_H__ */
--- /dev/null
+/* include/asm-arm/arch-lh7a40x/clocks.h
+ *
+ * Copyright (C) 2004 Marc Singer
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ */
+
+#include <linux/config.h>
+
+#ifndef __ASM_ARCH_CLOCKS_H
+#define __ASM_ARCH_CLOCKS_H
+
+unsigned int fclkfreq_get (void);
+unsigned int hclkfreq_get (void);
+unsigned int pclkfreq_get (void);
+
+#endif /* _ASM_ARCH_CLOCKS_H */
#if defined (CONFIG_MACH_LPD7A400) || defined (CONFIG_MACH_LPD7A404)
-# define IOBARRIER_PHYS 0xc0000000 /* Start of SDRAM */
-/*# define IOBARRIER_PHYS 0x00000000 */ /* Start of flash */
+# define IOBARRIER_PHYS 0x10000000 /* Second bank, fastest timing */
# define IOBARRIER_VIRT 0xf0000000
# define IOBARRIER_SIZE PAGE_SIZE
# define CPLD08_PHYS CPLDX_PHYS (0x08)
# define CPLD08_VIRT CPLDX_VIRT (0x08)
# define CPLD08_SIZE PAGE_SIZE
+# define CPLD0A_PHYS CPLDX_PHYS (0x0a)
+# define CPLD0A_VIRT CPLDX_VIRT (0x0a)
+# define CPLD0A_SIZE PAGE_SIZE
# define CPLD0C_PHYS CPLDX_PHYS (0x0c)
# define CPLD0C_VIRT CPLDX_VIRT (0x0c)
# define CPLD0C_SIZE PAGE_SIZE
#define XTAL_IN 14745600 /* 14.7456 MHz crystal */
#define PLL_CLOCK (XTAL_IN * 21) /* 309 MHz PLL clock */
#define MAX_HCLK_KHZ 100000 /* HCLK max limit ~100MHz */
+#define HCLK (99993600)
+//#define HCLK (119808000)
#endif /* __ASM_ARCH_CONSTANTS_H */
/* include/asm-arm/arch-lh7a40x/dma.h
*
- * Copyright (C) 2003 Coastal Environmental Systems
+ * Copyright (C) 2005 Marc Singer
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License
* version 2 as published by the Free Software Foundation.
*
*/
+
+typedef enum {
+ DMA_M2M0 = 0,
+ DMA_M2M1 = 1,
+ DMA_M2P0 = 2, /* Tx */
+ DMA_M2P1 = 3, /* Rx */
+ DMA_M2P2 = 4, /* Tx */
+ DMA_M2P3 = 5, /* Rx */
+ DMA_M2P4 = 6, /* Tx - AC97 */
+ DMA_M2P5 = 7, /* Rx - AC97 */
+ DMA_M2P6 = 8, /* Tx */
+ DMA_M2P7 = 9, /* Rx */
+} dma_device_t;
+
+#define DMA_LENGTH_MAX ((64*1024) - 4) /* bytes */
+
+#define DMAC_GCA __REG(DMAC_PHYS + 0x2b80)
+#define DMAC_GIR __REG(DMAC_PHYS + 0x2bc0)
+
+#define DMAC_GIR_MMI1 (1<<11)
+#define DMAC_GIR_MMI0 (1<<10)
+#define DMAC_GIR_MPI8 (1<<9)
+#define DMAC_GIR_MPI9 (1<<8)
+#define DMAC_GIR_MPI6 (1<<7)
+#define DMAC_GIR_MPI7 (1<<6)
+#define DMAC_GIR_MPI4 (1<<5)
+#define DMAC_GIR_MPI5 (1<<4)
+#define DMAC_GIR_MPI2 (1<<3)
+#define DMAC_GIR_MPI3 (1<<2)
+#define DMAC_GIR_MPI0 (1<<1)
+#define DMAC_GIR_MPI1 (1<<0)
+
+#define DMAC_M2P0 0x0000
+#define DMAC_M2P1 0x0040
+#define DMAC_M2P2 0x0080
+#define DMAC_M2P3 0x00c0
+#define DMAC_M2P4 0x0240
+#define DMAC_M2P5 0x0200
+#define DMAC_M2P6 0x02c0
+#define DMAC_M2P7 0x0280
+#define DMAC_M2P8 0x0340
+#define DMAC_M2P9 0x0300
+#define DMAC_M2M0 0x0100
+#define DMAC_M2M1 0x0140
+
+#define DMAC_P_PCONTROL(c) __REG(DMAC_PHYS + (c) + 0x00)
+#define DMAC_P_PINTERRUPT(c) __REG(DMAC_PHYS + (c) + 0x04)
+#define DMAC_P_PPALLOC(c) __REG(DMAC_PHYS + (c) + 0x08)
+#define DMAC_P_PSTATUS(c) __REG(DMAC_PHYS + (c) + 0x0c)
+#define DMAC_P_REMAIN(c) __REG(DMAC_PHYS + (c) + 0x14)
+#define DMAC_P_MAXCNT0(c) __REG(DMAC_PHYS + (c) + 0x20)
+#define DMAC_P_BASE0(c) __REG(DMAC_PHYS + (c) + 0x24)
+#define DMAC_P_CURRENT0(c) __REG(DMAC_PHYS + (c) + 0x28)
+#define DMAC_P_MAXCNT1(c) __REG(DMAC_PHYS + (c) + 0x30)
+#define DMAC_P_BASE1(c) __REG(DMAC_PHYS + (c) + 0x34)
+#define DMAC_P_CURRENT1(c) __REG(DMAC_PHYS + (c) + 0x38)
+
+#define DMAC_PCONTROL_ENABLE (1<<4)
+
+#define DMAC_PORT_USB 0
+#define DMAC_PORT_SDMMC 1
+#define DMAC_PORT_AC97_1 2
+#define DMAC_PORT_AC97_2 3
+#define DMAC_PORT_AC97_3 4
+#define DMAC_PORT_UART1 6
+#define DMAC_PORT_UART2 7
+#define DMAC_PORT_UART3 8
+
+#define DMAC_PSTATUS_CURRSTATE_SHIFT 4
+#define DMAC_PSTATUS_CURRSTATE_MASK 0x3
+
+#define DMAC_PSTATUS_NEXTBUF (1<<6)
+#define DMAC_PSTATUS_STALLRINT (1<<0)
+
+#define DMAC_INT_CHE (1<<3)
+#define DMAC_INT_NFB (1<<1)
+#define DMAC_INT_STALL (1<<0)
#ifndef __ASM_ARCH_HARDWARE_H
#define __ASM_ARCH_HARDWARE_H
+#include <asm/sizes.h> /* Added for the sake of amba-clcd driver */
+
#define io_p2v(x) (0xf0000000 | (((x) & 0xfff00000) >> 4) | ((x) & 0x0000ffff))
#define io_v2p(x) ( (((x) & 0x0fff0000) << 4) | ((x) & 0x0000ffff))
#endif
+#define MASK_AND_SET(v,m,s) (v) = ((v)&~(m))|(s)
+
#include "registers.h"
#endif /* _ASM_ARCH_HARDWARE_H */
#if !defined (IRQ_GPIO0INTR)
# define IRQ_GPIO0INTR IRQ_GPIO0FIQ
#endif
-#define IRQ_TICK IRQ_TINTR
+#define IRQ_TICK IRQ_TINTR
#define IRQ_PCC1_RDY IRQ_GPIO6INTR /* PCCard 1 ready */
#define IRQ_PCC2_RDY IRQ_GPIO7INTR /* PCCard 2 ready */
+#define IRQ_USB IRQ_USBINTR /* USB device */
#ifdef CONFIG_MACH_KEV7A400
# define IRQ_TS IRQ_GPIOFIQ /* Touchscreen */
# define IRQ_LPD7A400_TS IRQ_LPD7A40X_CPLD + 1 /* Touch screen */
#endif
+#if defined (CONFIG_MACH_LPD7A400)
+# define IRQ_TOUCH IRQ_LPD7A400_TS
+#endif
+
#define NR_IRQS (NR_IRQ_CPU + NR_IRQ_BOARD)
#endif
/* Physical register base addresses */
-#define AC97_PHYS (0x80000000) /* AC97 Controller */
+#define AC97C_PHYS (0x80000000) /* AC97 Controller */
#define MMC_PHYS (0x80000100) /* Multimedia Card Controller */
#define USB_PHYS (0x80000200) /* USB Client */
#define SCI_PHYS (0x80000300) /* Secure Card Interface */
#define RTC_PHYS (0x80000d00) /* Real-time Clock */
#define GPIO_PHYS (0x80000e00) /* General Purpose IO */
#define BMI_PHYS (0x80000f00) /* Battery Monitor Interface */
+#define HRTFTC_PHYS (0x80001000) /* High-res TFT Controller (LH7A400) */
+#define ALI_PHYS (0x80001000) /* Advanced LCD Interface (LH7A404) */
#define WDT_PHYS (0x80001400) /* Watchdog Timer */
#define SMC_PHYS (0x80002000) /* Static Memory Controller */
#define SDRC_PHYS (0x80002400) /* SDRAM Controller */
/* Physical registers of the LH7A404 */
+#define ADC_PHYS (0x80001300) /* A/D & Touchscreen Controller */
#define VIC1_PHYS (0x80008000) /* Vectored Interrupt Controller 1 */
#define USBH_PHYS (0x80009000) /* USB OHCI host controller */
#define VIC2_PHYS (0x8000a000) /* Vectored Interrupt Controller 2 */
/* Clock/State Controller register */
+#define CSC_PWRSR __REG(CSC_PHYS + 0x00) /* Reset register & ID */
#define CSC_PWRCNT __REG(CSC_PHYS + 0x04) /* Power control */
+#define CSC_CLKSET __REG(CSC_PHYS + 0x20) /* Clock speed control */
+#define CSC_USBDRESET __REG(CSC_PHYS + 0x4c) /* USB Device resets */
#define CSC_PWRCNT_USBH_EN (1<<28) /* USB Host power enable */
-
+#define CSC_PWRCNT_DMAC_M2M1_EN (1<<27)
+#define CSC_PWRCNT_DMAC_M2M0_EN (1<<26)
+#define CSC_PWRCNT_DMAC_M2P8_EN (1<<25)
+#define CSC_PWRCNT_DMAC_M2P9_EN (1<<24)
+#define CSC_PWRCNT_DMAC_M2P6_EN (1<<23)
+#define CSC_PWRCNT_DMAC_M2P7_EN (1<<22)
+#define CSC_PWRCNT_DMAC_M2P4_EN (1<<21)
+#define CSC_PWRCNT_DMAC_M2P5_EN (1<<20)
+#define CSC_PWRCNT_DMAC_M2P2_EN (1<<19)
+#define CSC_PWRCNT_DMAC_M2P3_EN (1<<18)
+#define CSC_PWRCNT_DMAC_M2P0_EN (1<<17)
+#define CSC_PWRCNT_DMAC_M2P1_EN (1<<16)
+
+#define CSC_PWRSR_CHIPMAN_SHIFT (24)
+#define CSC_PWRSR_CHIPMAN_MASK (0xff)
+#define CSC_PWRSR_CHIPID_SHIFT (16)
+#define CSC_PWRSR_CHIPID_MASK (0xff)
+
+#define CSC_USBDRESET_APBRESETREG (1<<1)
+#define CSC_USBDRESET_IORESETREG (1<<0)
/* Interrupt Controller registers */
#define GPIO_GPIOFEOI __REG(GPIO_PHYS + 0x54) /* GPIO End-of-Interrupt */
#define GPIO_GPIOINTEN __REG(GPIO_PHYS + 0x58) /* GPIO Interrupt Enable */
#define GPIO_INTSTATUS __REG(GPIO_PHYS + 0x5c) /* GPIO Interrupt Status */
+#define GPIO_PINMUX __REG(GPIO_PHYS + 0x2c)
+#define GPIO_PADD __REG(GPIO_PHYS + 0x10)
+#define GPIO_PAD __REG(GPIO_PHYS + 0x00)
+#define GPIO_PCD __REG(GPIO_PHYS + 0x08)
+#define GPIO_PCDD __REG(GPIO_PHYS + 0x18)
+#define GPIO_PEDD __REG(GPIO_PHYS + 0x24)
+#define GPIO_PED __REG(GPIO_PHYS + 0x20)
/* Static Memory Controller registers */
#endif
#if defined (CONFIG_MACH_LPD7A400) || defined (CONFIG_MACH_LPD7A404)
-# define CPLD_CONTROL __REG8(CPLD02_PHYS)
-# define CPLD_SPI_DATA __REG8(CPLD06_PHYS)
-# define CPLD_SPI_CONTROL __REG8(CPLD08_PHYS)
-# define CPLD_SPI_EEPROM __REG8(CPLD0A_PHYS)
-# define CPLD_INTERRUPTS __REG8(CPLD0C_PHYS) /* IRQ mask/status */
-# define CPLD_BOOT_MODE __REG8(CPLD0E_PHYS)
-# define CPLD_FLASH __REG8(CPLD10_PHYS)
-# define CPLD_POWER_MGMT __REG8(CPLD12_PHYS)
-# define CPLD_REVISION __REG8(CPLD14_PHYS)
-# define CPLD_GPIO_EXT __REG8(CPLD16_PHYS)
-# define CPLD_GPIO_DATA __REG8(CPLD18_PHYS)
-# define CPLD_GPIO_DIR __REG8(CPLD1A_PHYS)
-#endif
+# define CPLD_CONTROL __REG16(CPLD02_PHYS)
+# define CPLD_SPI_DATA __REG16(CPLD06_PHYS)
+# define CPLD_SPI_CONTROL __REG16(CPLD08_PHYS)
+# define CPLD_SPI_EEPROM __REG16(CPLD0A_PHYS)
+# define CPLD_INTERRUPTS __REG16(CPLD0C_PHYS) /* IRQ mask/status */
+# define CPLD_BOOT_MODE __REG16(CPLD0E_PHYS)
+# define CPLD_FLASH __REG16(CPLD10_PHYS)
+# define CPLD_POWER_MGMT __REG16(CPLD12_PHYS)
+# define CPLD_REVISION __REG16(CPLD14_PHYS)
+# define CPLD_GPIO_EXT __REG16(CPLD16_PHYS)
+# define CPLD_GPIO_DATA __REG16(CPLD18_PHYS)
+# define CPLD_GPIO_DIR __REG16(CPLD1A_PHYS)
+
+#endif
/* Timer registers */
#endif /* _ASM_ARCH_REGISTERS_H */
-
--- /dev/null
+/* ssp.h
+ $Id$
+
+ written by Marc Singer
+ 6 Dec 2004
+
+ Copyright (C) 2004 Marc Singer
+
+ -----------
+ DESCRIPTION
+ -----------
+
+ This SSP header is available throughout the kernel, for this
+ machine/architecture, because drivers that use it may be dispersed.
+
+ This file was cloned from the 7952x implementation. It would be
+ better to share them, but we're taking an easier approach for the
+ time being.
+
+*/
+
+#if !defined (__SSP_H__)
+# define __SSP_H__
+
+/* ----- Includes */
+
+/* ----- Types */
+
+struct ssp_driver {
+ int (*init) (void);
+ void (*exit) (void);
+ void (*acquire) (void);
+ void (*release) (void);
+ int (*configure) (int device, int mode, int speed,
+ int frame_size_write, int frame_size_read);
+ void (*chip_select) (int enable);
+ void (*set_callbacks) (void* handle,
+ irqreturn_t (*callback_tx)(void*),
+ irqreturn_t (*callback_rx)(void*));
+ void (*enable) (void);
+ void (*disable) (void);
+// int (*save_state) (void*);
+// void (*restore_state) (void*);
+ int (*read) (void);
+ int (*write) (u16 data);
+ int (*write_read) (u16 data);
+ void (*flush) (void);
+ void (*write_async) (void* pv, size_t cb);
+ size_t (*write_pos) (void);
+};
+
+ /* These modes are only available on the LH79524 */
+#define SSP_MODE_SPI (1)
+#define SSP_MODE_SSI (2)
+#define SSP_MODE_MICROWIRE (3)
+#define SSP_MODE_I2S (4)
+
+ /* CPLD SPI devices */
+#define DEVICE_EEPROM 0 /* Configuration eeprom */
+#define DEVICE_MAC 1 /* MAC eeprom (LPD79524) */
+#define DEVICE_CODEC 2 /* Audio codec */
+#define DEVICE_TOUCH 3 /* Touch screen (LPD79520) */
+
+/* ----- Globals */
+
+/* ----- Prototypes */
+
+//extern struct ssp_driver lh79520_i2s_driver;
+extern struct ssp_driver lh7a400_cpld_ssp_driver;
+
+#endif /* __SSP_H__ */
#ifndef UART_R_STATUS
# define UART_R_STATUS (0x10)
#endif
-#define nTxRdy (0x20) /* Not TxReady (literally Tx FIFO full) */
+#define nTxRdy (0x20) /* Not TxReady (literally Tx FIFO full) */
/* Access UART with physical addresses before MMU is setup */
#define UART_STATUS (*(volatile unsigned long*) (UART2_PHYS + UART_R_STATUS))
projects / kernel / kernel-generic.git / commitdiff