select CPU_V7
select SUPPORT_SPL
-config TARGET_TSERIES
- bool "Support tseries"
+config TARGET_BRPPT1
+ bool "Support BRPPT1"
select CPU_V7
select SUPPORT_SPL
source "board/bosch/shc/Kconfig"
source "board/BuR/kwb/Kconfig"
-source "board/BuR/tseries/Kconfig"
+source "board/BuR/brppt1/Kconfig"
source "board/CarMediaLab/flea3/Kconfig"
source "board/Marvell/aspenite/Kconfig"
source "board/Marvell/gplugd/Kconfig"
--- /dev/null
+if TARGET_BRPPT1
+
+config SYS_BOARD
+ default "brppt1"
+
+config SYS_VENDOR
+ default "BuR"
+
+config SYS_SOC
+ default "am33xx"
+
+config SYS_CONFIG_NAME
+ default "brppt1"
+
+endif
--- /dev/null
+BRPPT1 BOARD
+M: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
+S: Maintained
+F: board/BuR/brppt1/
+F: include/configs/brppt1.h
+F: configs/brppt1_mmc_defconfig
+F: configs/brppt1_nand_defconfig
+F: configs/brppt1_spi_defconfig
--- /dev/null
+#
+# Makefile
+#
+# Copyright (C) 2013 Hannes Schmelzer <oe5hpm@oevsv.at>
+# Bernecker & Rainer Industrieelektronik GmbH - http://www.br-automation.com
+#
+# SPDX-License-Identifier: GPL-2.0+
+#
+
+ifeq ($(CONFIG_SPL_BUILD),y)
+obj-y := mux.o
+endif
+obj-y += ../common/common.o
+obj-y += board.o
--- /dev/null
+/*
+ * board.c
+ *
+ * Board functions for B&R BRPPT1
+ *
+ * Copyright (C) 2013 Hannes Schmelzer <oe5hpm@oevsv.at>
+ * Bernecker & Rainer Industrieelektronik GmbH - http://www.br-automation.com
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ *
+ */
+
+#include <common.h>
+#include <errno.h>
+#include <spl.h>
+#include <asm/arch/cpu.h>
+#include <asm/arch/hardware.h>
+#include <asm/arch/omap.h>
+#include <asm/arch/ddr_defs.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/gpio.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/arch/mem.h>
+#include <asm/io.h>
+#include <asm/emif.h>
+#include <asm/gpio.h>
+#include <i2c.h>
+#include <power/tps65217.h>
+#include "../common/bur_common.h"
+#include <lcd.h>
+#include <watchdog.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+/* --------------------------------------------------------------------------*/
+/* -- defines for GPIO -- */
+#define REPSWITCH (0+20) /* GPIO0_20 */
+
+#if defined(CONFIG_SPL_BUILD)
+/* TODO: check ram-timing ! */
+static const struct ddr_data ddr3_data = {
+ .datardsratio0 = MT41K256M16HA125E_RD_DQS,
+ .datawdsratio0 = MT41K256M16HA125E_WR_DQS,
+ .datafwsratio0 = MT41K256M16HA125E_PHY_FIFO_WE,
+ .datawrsratio0 = MT41K256M16HA125E_PHY_WR_DATA,
+};
+
+static const struct cmd_control ddr3_cmd_ctrl_data = {
+ .cmd0csratio = MT41K256M16HA125E_RATIO,
+ .cmd0iclkout = MT41K256M16HA125E_INVERT_CLKOUT,
+
+ .cmd1csratio = MT41K256M16HA125E_RATIO,
+ .cmd1iclkout = MT41K256M16HA125E_INVERT_CLKOUT,
+
+ .cmd2csratio = MT41K256M16HA125E_RATIO,
+ .cmd2iclkout = MT41K256M16HA125E_INVERT_CLKOUT,
+};
+
+static struct emif_regs ddr3_emif_reg_data = {
+ .sdram_config = MT41K256M16HA125E_EMIF_SDCFG,
+ .ref_ctrl = MT41K256M16HA125E_EMIF_SDREF,
+ .sdram_tim1 = MT41K256M16HA125E_EMIF_TIM1,
+ .sdram_tim2 = MT41K256M16HA125E_EMIF_TIM2,
+ .sdram_tim3 = MT41K256M16HA125E_EMIF_TIM3,
+ .zq_config = MT41K256M16HA125E_ZQ_CFG,
+ .emif_ddr_phy_ctlr_1 = MT41K256M16HA125E_EMIF_READ_LATENCY,
+};
+
+static const struct ctrl_ioregs ddr3_ioregs = {
+ .cm0ioctl = MT41K256M16HA125E_IOCTRL_VALUE,
+ .cm1ioctl = MT41K256M16HA125E_IOCTRL_VALUE,
+ .cm2ioctl = MT41K256M16HA125E_IOCTRL_VALUE,
+ .dt0ioctl = MT41K256M16HA125E_IOCTRL_VALUE,
+ .dt1ioctl = MT41K256M16HA125E_IOCTRL_VALUE,
+};
+
+#ifdef CONFIG_SPL_OS_BOOT
+/*
+ * called from spl_nand.c
+ * return 0 for loading linux, return 1 for loading u-boot
+ */
+int spl_start_uboot(void)
+{
+ if (0 == gpio_get_value(REPSWITCH)) {
+ mdelay(1000);
+ printf("SPL: entering u-boot instead kernel image.\n");
+ return 1;
+ }
+ return 0;
+}
+#endif /* CONFIG_SPL_OS_BOOT */
+
+#define OSC (V_OSCK/1000000)
+static const struct dpll_params dpll_ddr3 = { 400, OSC-1, 1, -1, -1, -1, -1};
+
+void am33xx_spl_board_init(void)
+{
+ struct cm_perpll *const cmper = (struct cm_perpll *)CM_PER;
+ /*struct cm_wkuppll *const cmwkup = (struct cm_wkuppll *)CM_WKUP;*/
+ struct cm_dpll *const cmdpll = (struct cm_dpll *)CM_DPLL;
+
+ /*
+ * in TRM they write a reset value of 1 (=CLK_M_OSC) for the
+ * CLKSEL_TIMER6_CLK Register, in fact reset value is 0, so we need set
+ * the source of timer6 clk to CLK_M_OSC
+ */
+ writel(0x01, &cmdpll->clktimer6clk);
+
+ /* enable additional clocks of modules which are accessed later */
+ u32 *const clk_domains[] = {
+ &cmper->lcdcclkstctrl,
+ 0
+ };
+
+ u32 *const clk_modules_tsspecific[] = {
+ &cmper->lcdclkctrl,
+ &cmper->timer5clkctrl,
+ &cmper->timer6clkctrl,
+ 0
+ };
+ do_enable_clocks(clk_domains, clk_modules_tsspecific, 1);
+
+ /* setup LCD-Pixel Clock */
+ writel(0x2, &cmdpll->clklcdcpixelclk); /* clock comes from perPLL M2 */
+
+ /* setup I2C */
+ enable_i2c_pin_mux();
+ i2c_set_bus_num(0);
+ i2c_init(CONFIG_SYS_OMAP24_I2C_SPEED, CONFIG_SYS_OMAP24_I2C_SLAVE);
+ pmicsetup(0);
+
+ gpio_direction_output(64+29, 1); /* switch NAND_RnB to GPMC_WAIT1 */
+ gpio_direction_output(64+28, 1); /* switch MII2_CRS to GPMC_WAIT0 */
+}
+
+const struct dpll_params *get_dpll_ddr_params(void)
+{
+ return &dpll_ddr3;
+}
+
+void sdram_init(void)
+{
+ config_ddr(400, &ddr3_ioregs,
+ &ddr3_data,
+ &ddr3_cmd_ctrl_data,
+ &ddr3_emif_reg_data, 0);
+}
+#endif /* CONFIG_SPL_BUILD */
+
+/* Basic board specific setup. Pinmux has been handled already. */
+int board_init(void)
+{
+#if defined(CONFIG_HW_WATCHDOG)
+ hw_watchdog_init();
+#endif
+ gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
+#ifdef CONFIG_NAND
+ gpmc_init();
+#endif
+ return 0;
+}
+
+#ifdef CONFIG_BOARD_LATE_INIT
+int board_late_init(void)
+{
+ if (0 == gpio_get_value(REPSWITCH)) {
+ lcd_position_cursor(1, 8);
+ lcd_puts(
+ "switching to network-console ... ");
+ setenv("bootcmd", "run netconsole");
+ }
+ return 0;
+}
+#endif /* CONFIG_BOARD_LATE_INIT */
--- /dev/null
+/*
+ * mux.c
+ *
+ * Pinmux Setting for B&R BRPPT1 Board(s)
+ *
+ * Copyright (C) 2013 Hannes Schmelzer <oe5hpm@oevsv.at>
+ * Bernecker & Rainer Industrieelektronik GmbH - http://www.br-automation.com
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/arch/hardware.h>
+#include <asm/arch/mux.h>
+#include <asm/io.h>
+#include <i2c.h>
+
+static struct module_pin_mux uart0_pin_mux[] = {
+ /* UART0_RTS */
+ {OFFSET(uart0_rtsn), (MODE(0) | PULLUDEN)},
+ /* UART0_CTS */
+ {OFFSET(uart0_ctsn), (MODE(0) | PULLUDEN | PULLUP_EN | RXACTIVE)},
+ /* UART0_RXD */
+ {OFFSET(uart0_rxd), (MODE(0) | PULLUDEN | PULLUP_EN | RXACTIVE)},
+ /* UART0_TXD */
+ {OFFSET(uart0_txd), (MODE(0) | PULLUDEN)},
+ {-1},
+};
+static struct module_pin_mux uart1_pin_mux[] = {
+ /* UART1_RTS as I2C2-SCL */
+ {OFFSET(uart1_rtsn), (MODE(3) | PULLUDEN | PULLUP_EN | RXACTIVE)},
+ /* UART1_CTS as I2C2-SDA */
+ {OFFSET(uart1_ctsn), (MODE(3) | PULLUDEN | PULLUP_EN | RXACTIVE)},
+ /* UART1_RXD */
+ {OFFSET(uart1_rxd), (MODE(0) | PULLUDEN | PULLUP_EN | RXACTIVE)},
+ /* UART1_TXD */
+ {OFFSET(uart1_txd), (MODE(0) | PULLUDEN)},
+ {-1},
+};
+#ifdef CONFIG_MMC
+static struct module_pin_mux mmc1_pin_mux[] = {
+ {OFFSET(gpmc_ad7), (MODE(1) | RXACTIVE | PULLUP_EN)}, /* MMC1_DAT7 */
+ {OFFSET(gpmc_ad6), (MODE(1) | RXACTIVE | PULLUP_EN)}, /* MMC1_DAT6 */
+ {OFFSET(gpmc_ad5), (MODE(1) | RXACTIVE | PULLUP_EN)}, /* MMC1_DAT5 */
+ {OFFSET(gpmc_ad4), (MODE(1) | RXACTIVE | PULLUP_EN)}, /* MMC1_DAT4 */
+
+ {OFFSET(gpmc_ad3), (MODE(1) | RXACTIVE | PULLUP_EN)}, /* MMC1_DAT3 */
+ {OFFSET(gpmc_ad2), (MODE(1) | RXACTIVE | PULLUP_EN)}, /* MMC1_DAT2 */
+ {OFFSET(gpmc_ad1), (MODE(1) | RXACTIVE | PULLUP_EN)}, /* MMC1_DAT1 */
+ {OFFSET(gpmc_ad0), (MODE(1) | RXACTIVE | PULLUP_EN)}, /* MMC1_DAT0 */
+ {OFFSET(gpmc_csn1), (MODE(2) | RXACTIVE | PULLUP_EN)}, /* MMC1_CLK */
+ {OFFSET(gpmc_csn2), (MODE(2) | RXACTIVE | PULLUP_EN)}, /* MMC1_CMD */
+ {OFFSET(gpmc_csn0), (MODE(7) | RXACTIVE | PULLUP_EN)}, /* MMC1_WP */
+ {OFFSET(gpmc_advn_ale), (MODE(7) | RXACTIVE | PULLUP_EN)},/* MMC1_CD */
+ {-1},
+};
+#endif
+static struct module_pin_mux i2c0_pin_mux[] = {
+ /* I2C_DATA */
+ {OFFSET(i2c0_sda), (MODE(0) | RXACTIVE | PULLUDEN | SLEWCTRL)},
+ /* I2C_SCLK */
+ {OFFSET(i2c0_scl), (MODE(0) | RXACTIVE | PULLUDEN | SLEWCTRL)},
+ {-1},
+};
+
+static struct module_pin_mux spi0_pin_mux[] = {
+ /* SPI0_SCLK */
+ {OFFSET(spi0_sclk), (MODE(0) | RXACTIVE | PULLUDEN | PULLUP_EN)},
+ /* SPI0_D0 */
+ {OFFSET(spi0_d0), (MODE(0) | RXACTIVE | PULLUDEN | PULLUP_EN)},
+ /* SPI0_D1 */
+ {OFFSET(spi0_d1), (MODE(0) | RXACTIVE | PULLUDEN | PULLUP_EN)},
+ /* SPI0_CS0 */
+ {OFFSET(spi0_cs0), (MODE(0) | RXACTIVE | PULLUDEN | PULLUP_EN)},
+ {-1},
+};
+
+static struct module_pin_mux mii1_pin_mux[] = {
+ {OFFSET(mii1_crs), MODE(0) | RXACTIVE}, /* MII1_CRS */
+ {OFFSET(mii1_col), MODE(0) | RXACTIVE}, /* MII1_COL */
+ {OFFSET(mii1_rxerr), MODE(0) | RXACTIVE}, /* MII1_RXERR */
+ {OFFSET(mii1_txen), MODE(0)}, /* MII1_TXEN */
+ {OFFSET(mii1_rxdv), MODE(0) | RXACTIVE}, /* MII1_RXDV */
+ {OFFSET(mii1_txd3), MODE(0)}, /* MII1_TXD3 */
+ {OFFSET(mii1_txd2), MODE(0)}, /* MII1_TXD2 */
+ {OFFSET(mii1_txd1), MODE(0)}, /* MII1_TXD1 */
+ {OFFSET(mii1_txd0), MODE(0)}, /* MII1_TXD0 */
+ {OFFSET(mii1_txclk), MODE(0) | RXACTIVE}, /* MII1_TXCLK */
+ {OFFSET(mii1_rxclk), MODE(0) | RXACTIVE}, /* MII1_RXCLK */
+ {OFFSET(mii1_rxd3), MODE(0) | RXACTIVE}, /* MII1_RXD3 */
+ {OFFSET(mii1_rxd2), MODE(0) | RXACTIVE}, /* MII1_RXD2 */
+ {OFFSET(mii1_rxd1), MODE(0) | RXACTIVE}, /* MII1_RXD1 */
+ {OFFSET(mii1_rxd0), MODE(0) | RXACTIVE}, /* MII1_RXD0 */
+ {OFFSET(mdio_data), MODE(0) | RXACTIVE | PULLUP_EN},/* MDIO_DATA */
+ {OFFSET(mdio_clk), MODE(0) | PULLUP_EN}, /* MDIO_CLK */
+ {-1},
+};
+
+static struct module_pin_mux mii2_pin_mux[] = {
+ {OFFSET(gpmc_a0), MODE(1)}, /* MII2_TXEN */
+ {OFFSET(gpmc_a1), MODE(1) | RXACTIVE}, /* MII2_RXDV */
+ {OFFSET(gpmc_a2), MODE(1)}, /* MII2_TXD3 */
+ {OFFSET(gpmc_a3), MODE(1)}, /* MII2_TXD2 */
+ {OFFSET(gpmc_a4), MODE(1)}, /* MII2_TXD1 */
+ {OFFSET(gpmc_a5), MODE(1)}, /* MII2_TXD0 */
+ {OFFSET(gpmc_a6), MODE(1) | RXACTIVE}, /* MII2_TXCLK */
+ {OFFSET(gpmc_a7), MODE(1) | RXACTIVE}, /* MII2_RXCLK */
+ {OFFSET(gpmc_a8), MODE(1) | RXACTIVE}, /* MII2_RXD3 */
+ {OFFSET(gpmc_a9), MODE(1) | RXACTIVE}, /* MII2_RXD2 */
+ {OFFSET(gpmc_a10), MODE(1) | RXACTIVE}, /* MII2_RXD1 */
+ {OFFSET(gpmc_a11), MODE(1) | RXACTIVE}, /* MII2_RXD0 */
+ {OFFSET(gpmc_wpn), (MODE(1) | RXACTIVE)},/* MII2_RXERR */
+ {OFFSET(gpmc_wait0), (MODE(1) | RXACTIVE | PULLUP_EN)},
+ /*
+ * MII2_CRS is shared with
+ * NAND_WAIT0
+ */
+ {OFFSET(gpmc_be1n), (MODE(1) | RXACTIVE)},/* MII1_COL */
+ {-1},
+};
+#ifdef CONFIG_NAND
+static struct module_pin_mux nand_pin_mux[] = {
+ {OFFSET(gpmc_ad0), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD0 */
+ {OFFSET(gpmc_ad1), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD1 */
+ {OFFSET(gpmc_ad2), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD2 */
+ {OFFSET(gpmc_ad3), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD3 */
+ {OFFSET(gpmc_ad4), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD4 */
+ {OFFSET(gpmc_ad5), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD5 */
+ {OFFSET(gpmc_ad6), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD6 */
+ {OFFSET(gpmc_ad7), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD7 */
+ {OFFSET(gpmc_clk), (MODE(2) | RXACTIVE | PULLUP_EN)}, /* NAND WAIT */
+ {OFFSET(gpmc_wpn), (MODE(7) | PULLUP_EN | RXACTIVE)}, /* NAND_WPN */
+ {OFFSET(gpmc_csn0), (MODE(0) | PULLUDEN)}, /* NAND_CS0 */
+ {OFFSET(gpmc_advn_ale), (MODE(0) | PULLUDEN)}, /* NAND_ADV_ALE */
+ {OFFSET(gpmc_oen_ren), (MODE(0) | PULLUDEN)}, /* NAND_OE */
+ {OFFSET(gpmc_wen), (MODE(0) | PULLUDEN)}, /* NAND_WEN */
+ {OFFSET(gpmc_be0n_cle), (MODE(0) | PULLUDEN)}, /* NAND_BE_CLE */
+ {-1},
+};
+#endif
+static struct module_pin_mux gpIOs[] = {
+ /* GPIO0_6 (SPI0_CS1) - 3v3_PWR_nEN (Display Power Supply) */
+ {OFFSET(spi0_cs1), (MODE(7) | PULLUDEN | PULLUP_EN | RXACTIVE)},
+ /* TIMER5 (MMC0_DAT3) - TIMER5 (Buzzer) */
+ {OFFSET(mmc0_dat3), (MODE(3) | PULLUDEN | RXACTIVE)},
+ /* TIMER6 (MMC0_DAT2) - PWM_BACK_3V3 */
+ {OFFSET(mmc0_dat2), (MODE(3) | PULLUDEN | RXACTIVE)},
+ /* GPIO2_28 (MMC0_DAT1) - MII_nNAND */
+ {OFFSET(mmc0_dat1), (MODE(7) | PULLUDEN | RXACTIVE)},
+ /* GPIO2_29 (MMC0_DAT0) - NAND_1n0 */
+ {OFFSET(mmc0_dat0), (MODE(7) | PULLUDEN | RXACTIVE)},
+ /* GPIO2_30 (MMC0_CLK) - nRESET (PHY) */
+ {OFFSET(mmc0_clk), (MODE(7) | PULLUDEN | PULLUP_EN | RXACTIVE)},
+ /* GPIO3_18 (MCASP0_ACLKR) - CPLD JTAG TDI */
+ {OFFSET(mcasp0_aclkr), (MODE(7) | PULLUDEN | PULLUP_EN | RXACTIVE)},
+ /* GPIO3_19 (MCASP0_FSR) - CPLD JTAG TMS */
+ {OFFSET(mcasp0_fsr), (MODE(7) | PULLUDEN | PULLUP_EN | RXACTIVE)},
+ /* GPIO3_20 (MCASP0_AXR1) - CPLD JTAG TCK */
+ {OFFSET(mcasp0_axr1), (MODE(7) | PULLUDEN | PULLUP_EN | RXACTIVE)},
+ /* GPIO3_21 (MCASP0_AHCLKX) - CPLD JTAG TDO */
+ {OFFSET(mcasp0_ahclkx), (MODE(7) | PULLUDEN | PULLUP_EN | RXACTIVE)},
+ /* GPIO2_0 (GPMC_nCS3) - DCOK */
+ {OFFSET(gpmc_csn3), (MODE(7) | PULLUDDIS | RXACTIVE) },
+ /* GPIO0_29 (RMII1_REFCLK) - eMMC nRST */
+ {OFFSET(rmii1_refclk), (MODE(7) | PULLUDDIS | RXACTIVE) },
+ /*
+ * GPIO0_7 (PWW0 OUT)
+ * DISPLAY_ONOFF (Backlight Enable at LVDS Versions)
+ */
+ {OFFSET(ecap0_in_pwm0_out), (MODE(7) | PULLUDEN | RXACTIVE)},
+ /* GPIO0_19 (DMA_INTR0) - DISPLAY_MODE (CPLD) */
+ {OFFSET(xdma_event_intr0), (MODE(7) | PULLUDEN | PULLUP_EN | RXACTIVE)},
+ /* GPIO0_20 (DMA_INTR1) - REP-Switch */
+ {OFFSET(xdma_event_intr1), (MODE(7) | PULLUP_EN | RXACTIVE)},
+ /* GPIO3_14 (MCASP0_ACLKX) - frei / PP709 */
+ {OFFSET(mcasp0_aclkx), (MODE(7) | PULLUDEN | PULLUP_EN | RXACTIVE) },
+ /* GPIO3_15 (MCASP0_FSX) - PMIC_nRESET */
+ {OFFSET(mcasp0_fsx), (MODE(7) | PULLUDEN | PULLUP_EN | RXACTIVE) },
+ /* GPIO3_16 (MCASP0_AXR0) - ETH1_LEDY */
+ {OFFSET(mcasp0_axr0), (MODE(7) | PULLUDDIS) },
+ /* GPIO3_17 (MCASP0_AHCLKR) - ETH2_LEDY */
+ {OFFSET(mcasp0_ahclkr), (MODE(7) | PULLUDDIS) },
+#ifndef CONFIG_NAND
+ /* GPIO2_3 - NAND_OE */
+ {OFFSET(gpmc_oen_ren), (MODE(7) | PULLDOWN_EN | RXACTIVE)},
+ /* GPIO2_4 - NAND_WEN */
+ {OFFSET(gpmc_wen), (MODE(7) | PULLDOWN_EN | RXACTIVE)},
+ /* GPIO2_5 - NAND_BE_CLE */
+ {OFFSET(gpmc_be0n_cle), (MODE(7) | PULLDOWN_EN | RXACTIVE)},
+#endif
+ {-1},
+};
+
+static struct module_pin_mux lcd_pin_mux[] = {
+ {OFFSET(lcd_data0), (MODE(0) | PULLUDDIS)}, /* LCD-Data(0) */
+ {OFFSET(lcd_data1), (MODE(0) | PULLUDDIS)}, /* LCD-Data(1) */
+ {OFFSET(lcd_data2), (MODE(0) | PULLUDDIS)}, /* LCD-Data(2) */
+ {OFFSET(lcd_data3), (MODE(0) | PULLUDDIS)}, /* LCD-Data(3) */
+ {OFFSET(lcd_data4), (MODE(0) | PULLUDDIS)}, /* LCD-Data(4) */
+ {OFFSET(lcd_data5), (MODE(0) | PULLUDDIS)}, /* LCD-Data(5) */
+ {OFFSET(lcd_data6), (MODE(0) | PULLUDDIS)}, /* LCD-Data(6) */
+ {OFFSET(lcd_data7), (MODE(0) | PULLUDDIS)}, /* LCD-Data(7) */
+ {OFFSET(lcd_data8), (MODE(0) | PULLUDDIS)}, /* LCD-Data(8) */
+ {OFFSET(lcd_data9), (MODE(0) | PULLUDDIS)}, /* LCD-Data(9) */
+ {OFFSET(lcd_data10), (MODE(0) | PULLUDDIS)}, /* LCD-Data(10) */
+ {OFFSET(lcd_data11), (MODE(0) | PULLUDDIS)}, /* LCD-Data(11) */
+ {OFFSET(lcd_data12), (MODE(0) | PULLUDDIS)}, /* LCD-Data(12) */
+ {OFFSET(lcd_data13), (MODE(0) | PULLUDDIS)}, /* LCD-Data(13) */
+ {OFFSET(lcd_data14), (MODE(0) | PULLUDDIS)}, /* LCD-Data(14) */
+ {OFFSET(lcd_data15), (MODE(0) | PULLUDDIS)}, /* LCD-Data(15) */
+
+ {OFFSET(gpmc_ad8), (MODE(1) | PULLUDDIS)}, /* LCD-Data(16) */
+ {OFFSET(gpmc_ad9), (MODE(1) | PULLUDDIS)}, /* LCD-Data(17) */
+ {OFFSET(gpmc_ad10), (MODE(1) | PULLUDDIS)}, /* LCD-Data(18) */
+ {OFFSET(gpmc_ad11), (MODE(1) | PULLUDDIS)}, /* LCD-Data(19) */
+ {OFFSET(gpmc_ad12), (MODE(1) | PULLUDDIS)}, /* LCD-Data(20) */
+ {OFFSET(gpmc_ad13), (MODE(1) | PULLUDDIS)}, /* LCD-Data(21) */
+ {OFFSET(gpmc_ad14), (MODE(1) | PULLUDDIS)}, /* LCD-Data(22) */
+ {OFFSET(gpmc_ad15), (MODE(1) | PULLUDDIS)}, /* LCD-Data(23) */
+
+ {OFFSET(lcd_vsync), (MODE(0) | PULLUDDIS)}, /* LCD-VSync */
+ {OFFSET(lcd_hsync), (MODE(0) | PULLUDDIS)}, /* LCD-HSync */
+ {OFFSET(lcd_ac_bias_en), (MODE(0) | PULLUDDIS)},/* LCD-DE */
+ {OFFSET(lcd_pclk), (MODE(0) | PULLUDDIS)}, /* LCD-CLK */
+
+ {-1},
+};
+
+void enable_uart0_pin_mux(void)
+{
+ configure_module_pin_mux(uart0_pin_mux);
+}
+
+void enable_i2c_pin_mux(void)
+{
+ configure_module_pin_mux(i2c0_pin_mux);
+}
+
+void enable_board_pin_mux(void)
+{
+ configure_module_pin_mux(i2c0_pin_mux);
+ configure_module_pin_mux(mii1_pin_mux);
+ configure_module_pin_mux(mii2_pin_mux);
+#ifdef CONFIG_NAND
+ configure_module_pin_mux(nand_pin_mux);
+#elif defined(CONFIG_MMC)
+ configure_module_pin_mux(mmc1_pin_mux);
+#endif
+ configure_module_pin_mux(spi0_pin_mux);
+ configure_module_pin_mux(lcd_pin_mux);
+ configure_module_pin_mux(uart1_pin_mux);
+ configure_module_pin_mux(gpIOs);
+}
+++ /dev/null
-if TARGET_TSERIES
-
-config SYS_BOARD
- default "tseries"
-
-config SYS_VENDOR
- default "BuR"
-
-config SYS_SOC
- default "am33xx"
-
-config SYS_CONFIG_NAME
- default "tseries"
-
-endif
+++ /dev/null
-TSERIES BOARD
-M: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
-S: Maintained
-F: board/BuR/tseries/
-F: include/configs/tseries.h
-F: configs/tseries_mmc_defconfig
-F: configs/tseries_nand_defconfig
-F: configs/tseries_spi_defconfig
+++ /dev/null
-#
-# Makefile
-#
-# Copyright (C) 2013 Hannes Schmelzer <oe5hpm@oevsv.at>
-# Bernecker & Rainer Industrieelektronik GmbH - http://www.br-automation.com
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-
-ifeq ($(CONFIG_SPL_BUILD),y)
-obj-y := mux.o
-endif
-obj-y += ../common/common.o
-obj-y += board.o
+++ /dev/null
-/*
- * board.c
- *
- * Board functions for B&R LEIT Board
- *
- * Copyright (C) 2013 Hannes Schmelzer <oe5hpm@oevsv.at>
- * Bernecker & Rainer Industrieelektronik GmbH - http://www.br-automation.com
- *
- * SPDX-License-Identifier: GPL-2.0+
- *
- */
-
-#include <common.h>
-#include <errno.h>
-#include <spl.h>
-#include <asm/arch/cpu.h>
-#include <asm/arch/hardware.h>
-#include <asm/arch/omap.h>
-#include <asm/arch/ddr_defs.h>
-#include <asm/arch/clock.h>
-#include <asm/arch/gpio.h>
-#include <asm/arch/sys_proto.h>
-#include <asm/arch/mem.h>
-#include <asm/io.h>
-#include <asm/emif.h>
-#include <asm/gpio.h>
-#include <i2c.h>
-#include <power/tps65217.h>
-#include "../common/bur_common.h"
-#include <lcd.h>
-#include <watchdog.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-/* --------------------------------------------------------------------------*/
-/* -- defines for GPIO -- */
-#define REPSWITCH (0+20) /* GPIO0_20 */
-
-#if defined(CONFIG_SPL_BUILD)
-/* TODO: check ram-timing ! */
-static const struct ddr_data ddr3_data = {
- .datardsratio0 = MT41K256M16HA125E_RD_DQS,
- .datawdsratio0 = MT41K256M16HA125E_WR_DQS,
- .datafwsratio0 = MT41K256M16HA125E_PHY_FIFO_WE,
- .datawrsratio0 = MT41K256M16HA125E_PHY_WR_DATA,
-};
-
-static const struct cmd_control ddr3_cmd_ctrl_data = {
- .cmd0csratio = MT41K256M16HA125E_RATIO,
- .cmd0iclkout = MT41K256M16HA125E_INVERT_CLKOUT,
-
- .cmd1csratio = MT41K256M16HA125E_RATIO,
- .cmd1iclkout = MT41K256M16HA125E_INVERT_CLKOUT,
-
- .cmd2csratio = MT41K256M16HA125E_RATIO,
- .cmd2iclkout = MT41K256M16HA125E_INVERT_CLKOUT,
-};
-
-static struct emif_regs ddr3_emif_reg_data = {
- .sdram_config = MT41K256M16HA125E_EMIF_SDCFG,
- .ref_ctrl = MT41K256M16HA125E_EMIF_SDREF,
- .sdram_tim1 = MT41K256M16HA125E_EMIF_TIM1,
- .sdram_tim2 = MT41K256M16HA125E_EMIF_TIM2,
- .sdram_tim3 = MT41K256M16HA125E_EMIF_TIM3,
- .zq_config = MT41K256M16HA125E_ZQ_CFG,
- .emif_ddr_phy_ctlr_1 = MT41K256M16HA125E_EMIF_READ_LATENCY,
-};
-
-static const struct ctrl_ioregs ddr3_ioregs = {
- .cm0ioctl = MT41K256M16HA125E_IOCTRL_VALUE,
- .cm1ioctl = MT41K256M16HA125E_IOCTRL_VALUE,
- .cm2ioctl = MT41K256M16HA125E_IOCTRL_VALUE,
- .dt0ioctl = MT41K256M16HA125E_IOCTRL_VALUE,
- .dt1ioctl = MT41K256M16HA125E_IOCTRL_VALUE,
-};
-
-#ifdef CONFIG_SPL_OS_BOOT
-/*
- * called from spl_nand.c
- * return 0 for loading linux, return 1 for loading u-boot
- */
-int spl_start_uboot(void)
-{
- if (0 == gpio_get_value(REPSWITCH)) {
- mdelay(1000);
- printf("SPL: entering u-boot instead kernel image.\n");
- return 1;
- }
- return 0;
-}
-#endif /* CONFIG_SPL_OS_BOOT */
-
-#define OSC (V_OSCK/1000000)
-static const struct dpll_params dpll_ddr3 = { 400, OSC-1, 1, -1, -1, -1, -1};
-
-void am33xx_spl_board_init(void)
-{
- struct cm_perpll *const cmper = (struct cm_perpll *)CM_PER;
- /*struct cm_wkuppll *const cmwkup = (struct cm_wkuppll *)CM_WKUP;*/
- struct cm_dpll *const cmdpll = (struct cm_dpll *)CM_DPLL;
-
- /*
- * in TRM they write a reset value of 1 (=CLK_M_OSC) for the
- * CLKSEL_TIMER6_CLK Register, in fact reset value is 0, so we need set
- * the source of timer6 clk to CLK_M_OSC
- */
- writel(0x01, &cmdpll->clktimer6clk);
-
- /* enable additional clocks of modules which are accessed later */
- u32 *const clk_domains[] = {
- &cmper->lcdcclkstctrl,
- 0
- };
-
- u32 *const clk_modules_tsspecific[] = {
- &cmper->lcdclkctrl,
- &cmper->timer5clkctrl,
- &cmper->timer6clkctrl,
- 0
- };
- do_enable_clocks(clk_domains, clk_modules_tsspecific, 1);
-
- /* setup LCD-Pixel Clock */
- writel(0x2, &cmdpll->clklcdcpixelclk); /* clock comes from perPLL M2 */
-
- /* setup I2C */
- enable_i2c_pin_mux();
- i2c_set_bus_num(0);
- i2c_init(CONFIG_SYS_OMAP24_I2C_SPEED, CONFIG_SYS_OMAP24_I2C_SLAVE);
- pmicsetup(0);
-
- gpio_direction_output(64+29, 1); /* switch NAND_RnB to GPMC_WAIT1 */
- gpio_direction_output(64+28, 1); /* switch MII2_CRS to GPMC_WAIT0 */
-}
-
-const struct dpll_params *get_dpll_ddr_params(void)
-{
- return &dpll_ddr3;
-}
-
-void sdram_init(void)
-{
- config_ddr(400, &ddr3_ioregs,
- &ddr3_data,
- &ddr3_cmd_ctrl_data,
- &ddr3_emif_reg_data, 0);
-}
-#endif /* CONFIG_SPL_BUILD */
-
-/* Basic board specific setup. Pinmux has been handled already. */
-int board_init(void)
-{
-#if defined(CONFIG_HW_WATCHDOG)
- hw_watchdog_init();
-#endif
- gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
-#ifdef CONFIG_NAND
- gpmc_init();
-#endif
- return 0;
-}
-
-#ifdef CONFIG_BOARD_LATE_INIT
-int board_late_init(void)
-{
- if (0 == gpio_get_value(REPSWITCH)) {
- lcd_position_cursor(1, 8);
- lcd_puts(
- "switching to network-console ... ");
- setenv("bootcmd", "run netconsole");
- }
- return 0;
-}
-#endif /* CONFIG_BOARD_LATE_INIT */
+++ /dev/null
-/*
- * mux.c
- *
- * Pinmux Setting for B&R LEIT Board(s)
- *
- * Copyright (C) 2013 Hannes Schmelzer <oe5hpm@oevsv.at>
- * Bernecker & Rainer Industrieelektronik GmbH - http://www.br-automation.com
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <asm/arch/sys_proto.h>
-#include <asm/arch/hardware.h>
-#include <asm/arch/mux.h>
-#include <asm/io.h>
-#include <i2c.h>
-
-static struct module_pin_mux uart0_pin_mux[] = {
- /* UART0_RTS */
- {OFFSET(uart0_rtsn), (MODE(0) | PULLUDEN)},
- /* UART0_CTS */
- {OFFSET(uart0_ctsn), (MODE(0) | PULLUDEN | PULLUP_EN | RXACTIVE)},
- /* UART0_RXD */
- {OFFSET(uart0_rxd), (MODE(0) | PULLUDEN | PULLUP_EN | RXACTIVE)},
- /* UART0_TXD */
- {OFFSET(uart0_txd), (MODE(0) | PULLUDEN)},
- {-1},
-};
-static struct module_pin_mux uart1_pin_mux[] = {
- /* UART1_RTS as I2C2-SCL */
- {OFFSET(uart1_rtsn), (MODE(3) | PULLUDEN | PULLUP_EN | RXACTIVE)},
- /* UART1_CTS as I2C2-SDA */
- {OFFSET(uart1_ctsn), (MODE(3) | PULLUDEN | PULLUP_EN | RXACTIVE)},
- /* UART1_RXD */
- {OFFSET(uart1_rxd), (MODE(0) | PULLUDEN | PULLUP_EN | RXACTIVE)},
- /* UART1_TXD */
- {OFFSET(uart1_txd), (MODE(0) | PULLUDEN)},
- {-1},
-};
-#ifdef CONFIG_MMC
-static struct module_pin_mux mmc1_pin_mux[] = {
- {OFFSET(gpmc_ad7), (MODE(1) | RXACTIVE | PULLUP_EN)}, /* MMC1_DAT7 */
- {OFFSET(gpmc_ad6), (MODE(1) | RXACTIVE | PULLUP_EN)}, /* MMC1_DAT6 */
- {OFFSET(gpmc_ad5), (MODE(1) | RXACTIVE | PULLUP_EN)}, /* MMC1_DAT5 */
- {OFFSET(gpmc_ad4), (MODE(1) | RXACTIVE | PULLUP_EN)}, /* MMC1_DAT4 */
-
- {OFFSET(gpmc_ad3), (MODE(1) | RXACTIVE | PULLUP_EN)}, /* MMC1_DAT3 */
- {OFFSET(gpmc_ad2), (MODE(1) | RXACTIVE | PULLUP_EN)}, /* MMC1_DAT2 */
- {OFFSET(gpmc_ad1), (MODE(1) | RXACTIVE | PULLUP_EN)}, /* MMC1_DAT1 */
- {OFFSET(gpmc_ad0), (MODE(1) | RXACTIVE | PULLUP_EN)}, /* MMC1_DAT0 */
- {OFFSET(gpmc_csn1), (MODE(2) | RXACTIVE | PULLUP_EN)}, /* MMC1_CLK */
- {OFFSET(gpmc_csn2), (MODE(2) | RXACTIVE | PULLUP_EN)}, /* MMC1_CMD */
- {OFFSET(gpmc_csn0), (MODE(7) | RXACTIVE | PULLUP_EN)}, /* MMC1_WP */
- {OFFSET(gpmc_advn_ale), (MODE(7) | RXACTIVE | PULLUP_EN)},/* MMC1_CD */
- {-1},
-};
-#endif
-static struct module_pin_mux i2c0_pin_mux[] = {
- /* I2C_DATA */
- {OFFSET(i2c0_sda), (MODE(0) | RXACTIVE | PULLUDEN | SLEWCTRL)},
- /* I2C_SCLK */
- {OFFSET(i2c0_scl), (MODE(0) | RXACTIVE | PULLUDEN | SLEWCTRL)},
- {-1},
-};
-
-static struct module_pin_mux spi0_pin_mux[] = {
- /* SPI0_SCLK */
- {OFFSET(spi0_sclk), (MODE(0) | RXACTIVE | PULLUDEN | PULLUP_EN)},
- /* SPI0_D0 */
- {OFFSET(spi0_d0), (MODE(0) | RXACTIVE | PULLUDEN | PULLUP_EN)},
- /* SPI0_D1 */
- {OFFSET(spi0_d1), (MODE(0) | RXACTIVE | PULLUDEN | PULLUP_EN)},
- /* SPI0_CS0 */
- {OFFSET(spi0_cs0), (MODE(0) | RXACTIVE | PULLUDEN | PULLUP_EN)},
- {-1},
-};
-
-static struct module_pin_mux mii1_pin_mux[] = {
- {OFFSET(mii1_crs), MODE(0) | RXACTIVE}, /* MII1_CRS */
- {OFFSET(mii1_col), MODE(0) | RXACTIVE}, /* MII1_COL */
- {OFFSET(mii1_rxerr), MODE(0) | RXACTIVE}, /* MII1_RXERR */
- {OFFSET(mii1_txen), MODE(0)}, /* MII1_TXEN */
- {OFFSET(mii1_rxdv), MODE(0) | RXACTIVE}, /* MII1_RXDV */
- {OFFSET(mii1_txd3), MODE(0)}, /* MII1_TXD3 */
- {OFFSET(mii1_txd2), MODE(0)}, /* MII1_TXD2 */
- {OFFSET(mii1_txd1), MODE(0)}, /* MII1_TXD1 */
- {OFFSET(mii1_txd0), MODE(0)}, /* MII1_TXD0 */
- {OFFSET(mii1_txclk), MODE(0) | RXACTIVE}, /* MII1_TXCLK */
- {OFFSET(mii1_rxclk), MODE(0) | RXACTIVE}, /* MII1_RXCLK */
- {OFFSET(mii1_rxd3), MODE(0) | RXACTIVE}, /* MII1_RXD3 */
- {OFFSET(mii1_rxd2), MODE(0) | RXACTIVE}, /* MII1_RXD2 */
- {OFFSET(mii1_rxd1), MODE(0) | RXACTIVE}, /* MII1_RXD1 */
- {OFFSET(mii1_rxd0), MODE(0) | RXACTIVE}, /* MII1_RXD0 */
- {OFFSET(mdio_data), MODE(0) | RXACTIVE | PULLUP_EN},/* MDIO_DATA */
- {OFFSET(mdio_clk), MODE(0) | PULLUP_EN}, /* MDIO_CLK */
- {-1},
-};
-
-static struct module_pin_mux mii2_pin_mux[] = {
- {OFFSET(gpmc_a0), MODE(1)}, /* MII2_TXEN */
- {OFFSET(gpmc_a1), MODE(1) | RXACTIVE}, /* MII2_RXDV */
- {OFFSET(gpmc_a2), MODE(1)}, /* MII2_TXD3 */
- {OFFSET(gpmc_a3), MODE(1)}, /* MII2_TXD2 */
- {OFFSET(gpmc_a4), MODE(1)}, /* MII2_TXD1 */
- {OFFSET(gpmc_a5), MODE(1)}, /* MII2_TXD0 */
- {OFFSET(gpmc_a6), MODE(1) | RXACTIVE}, /* MII2_TXCLK */
- {OFFSET(gpmc_a7), MODE(1) | RXACTIVE}, /* MII2_RXCLK */
- {OFFSET(gpmc_a8), MODE(1) | RXACTIVE}, /* MII2_RXD3 */
- {OFFSET(gpmc_a9), MODE(1) | RXACTIVE}, /* MII2_RXD2 */
- {OFFSET(gpmc_a10), MODE(1) | RXACTIVE}, /* MII2_RXD1 */
- {OFFSET(gpmc_a11), MODE(1) | RXACTIVE}, /* MII2_RXD0 */
- {OFFSET(gpmc_wpn), (MODE(1) | RXACTIVE)},/* MII2_RXERR */
- {OFFSET(gpmc_wait0), (MODE(1) | RXACTIVE | PULLUP_EN)},
- /*
- * MII2_CRS is shared with
- * NAND_WAIT0
- */
- {OFFSET(gpmc_be1n), (MODE(1) | RXACTIVE)},/* MII1_COL */
- {-1},
-};
-#ifdef CONFIG_NAND
-static struct module_pin_mux nand_pin_mux[] = {
- {OFFSET(gpmc_ad0), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD0 */
- {OFFSET(gpmc_ad1), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD1 */
- {OFFSET(gpmc_ad2), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD2 */
- {OFFSET(gpmc_ad3), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD3 */
- {OFFSET(gpmc_ad4), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD4 */
- {OFFSET(gpmc_ad5), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD5 */
- {OFFSET(gpmc_ad6), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD6 */
- {OFFSET(gpmc_ad7), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD7 */
- {OFFSET(gpmc_clk), (MODE(2) | RXACTIVE | PULLUP_EN)}, /* NAND WAIT */
- {OFFSET(gpmc_wpn), (MODE(7) | PULLUP_EN | RXACTIVE)}, /* NAND_WPN */
- {OFFSET(gpmc_csn0), (MODE(0) | PULLUDEN)}, /* NAND_CS0 */
- {OFFSET(gpmc_advn_ale), (MODE(0) | PULLUDEN)}, /* NAND_ADV_ALE */
- {OFFSET(gpmc_oen_ren), (MODE(0) | PULLUDEN)}, /* NAND_OE */
- {OFFSET(gpmc_wen), (MODE(0) | PULLUDEN)}, /* NAND_WEN */
- {OFFSET(gpmc_be0n_cle), (MODE(0) | PULLUDEN)}, /* NAND_BE_CLE */
- {-1},
-};
-#endif
-static struct module_pin_mux gpIOs[] = {
- /* GPIO0_6 (SPI0_CS1) - 3v3_PWR_nEN (Display Power Supply) */
- {OFFSET(spi0_cs1), (MODE(7) | PULLUDEN | PULLUP_EN | RXACTIVE)},
- /* TIMER5 (MMC0_DAT3) - TIMER5 (Buzzer) */
- {OFFSET(mmc0_dat3), (MODE(3) | PULLUDEN | RXACTIVE)},
- /* TIMER6 (MMC0_DAT2) - PWM_BACK_3V3 */
- {OFFSET(mmc0_dat2), (MODE(3) | PULLUDEN | RXACTIVE)},
- /* GPIO2_28 (MMC0_DAT1) - MII_nNAND */
- {OFFSET(mmc0_dat1), (MODE(7) | PULLUDEN | RXACTIVE)},
- /* GPIO2_29 (MMC0_DAT0) - NAND_1n0 */
- {OFFSET(mmc0_dat0), (MODE(7) | PULLUDEN | RXACTIVE)},
- /* GPIO2_30 (MMC0_CLK) - nRESET (PHY) */
- {OFFSET(mmc0_clk), (MODE(7) | PULLUDEN | PULLUP_EN | RXACTIVE)},
- /* GPIO3_18 (MCASP0_ACLKR) - CPLD JTAG TDI */
- {OFFSET(mcasp0_aclkr), (MODE(7) | PULLUDEN | PULLUP_EN | RXACTIVE)},
- /* GPIO3_19 (MCASP0_FSR) - CPLD JTAG TMS */
- {OFFSET(mcasp0_fsr), (MODE(7) | PULLUDEN | PULLUP_EN | RXACTIVE)},
- /* GPIO3_20 (MCASP0_AXR1) - CPLD JTAG TCK */
- {OFFSET(mcasp0_axr1), (MODE(7) | PULLUDEN | PULLUP_EN | RXACTIVE)},
- /* GPIO3_21 (MCASP0_AHCLKX) - CPLD JTAG TDO */
- {OFFSET(mcasp0_ahclkx), (MODE(7) | PULLUDEN | PULLUP_EN | RXACTIVE)},
- /* GPIO2_0 (GPMC_nCS3) - DCOK */
- {OFFSET(gpmc_csn3), (MODE(7) | PULLUDDIS | RXACTIVE) },
- /* GPIO0_29 (RMII1_REFCLK) - eMMC nRST */
- {OFFSET(rmii1_refclk), (MODE(7) | PULLUDDIS | RXACTIVE) },
- /*
- * GPIO0_7 (PWW0 OUT)
- * DISPLAY_ONOFF (Backlight Enable at LVDS Versions)
- */
- {OFFSET(ecap0_in_pwm0_out), (MODE(7) | PULLUDEN | RXACTIVE)},
- /* GPIO0_19 (DMA_INTR0) - DISPLAY_MODE (CPLD) */
- {OFFSET(xdma_event_intr0), (MODE(7) | PULLUDEN | PULLUP_EN | RXACTIVE)},
- /* GPIO0_20 (DMA_INTR1) - REP-Switch */
- {OFFSET(xdma_event_intr1), (MODE(7) | PULLUP_EN | RXACTIVE)},
- /* GPIO3_14 (MCASP0_ACLKX) - frei / PP709 */
- {OFFSET(mcasp0_aclkx), (MODE(7) | PULLUDEN | PULLUP_EN | RXACTIVE) },
- /* GPIO3_15 (MCASP0_FSX) - PMIC_nRESET */
- {OFFSET(mcasp0_fsx), (MODE(7) | PULLUDEN | PULLUP_EN | RXACTIVE) },
- /* GPIO3_16 (MCASP0_AXR0) - ETH1_LEDY */
- {OFFSET(mcasp0_axr0), (MODE(7) | PULLUDDIS) },
- /* GPIO3_17 (MCASP0_AHCLKR) - ETH2_LEDY */
- {OFFSET(mcasp0_ahclkr), (MODE(7) | PULLUDDIS) },
-#ifndef CONFIG_NAND
- /* GPIO2_3 - NAND_OE */
- {OFFSET(gpmc_oen_ren), (MODE(7) | PULLDOWN_EN | RXACTIVE)},
- /* GPIO2_4 - NAND_WEN */
- {OFFSET(gpmc_wen), (MODE(7) | PULLDOWN_EN | RXACTIVE)},
- /* GPIO2_5 - NAND_BE_CLE */
- {OFFSET(gpmc_be0n_cle), (MODE(7) | PULLDOWN_EN | RXACTIVE)},
-#endif
- {-1},
-};
-
-static struct module_pin_mux lcd_pin_mux[] = {
- {OFFSET(lcd_data0), (MODE(0) | PULLUDDIS)}, /* LCD-Data(0) */
- {OFFSET(lcd_data1), (MODE(0) | PULLUDDIS)}, /* LCD-Data(1) */
- {OFFSET(lcd_data2), (MODE(0) | PULLUDDIS)}, /* LCD-Data(2) */
- {OFFSET(lcd_data3), (MODE(0) | PULLUDDIS)}, /* LCD-Data(3) */
- {OFFSET(lcd_data4), (MODE(0) | PULLUDDIS)}, /* LCD-Data(4) */
- {OFFSET(lcd_data5), (MODE(0) | PULLUDDIS)}, /* LCD-Data(5) */
- {OFFSET(lcd_data6), (MODE(0) | PULLUDDIS)}, /* LCD-Data(6) */
- {OFFSET(lcd_data7), (MODE(0) | PULLUDDIS)}, /* LCD-Data(7) */
- {OFFSET(lcd_data8), (MODE(0) | PULLUDDIS)}, /* LCD-Data(8) */
- {OFFSET(lcd_data9), (MODE(0) | PULLUDDIS)}, /* LCD-Data(9) */
- {OFFSET(lcd_data10), (MODE(0) | PULLUDDIS)}, /* LCD-Data(10) */
- {OFFSET(lcd_data11), (MODE(0) | PULLUDDIS)}, /* LCD-Data(11) */
- {OFFSET(lcd_data12), (MODE(0) | PULLUDDIS)}, /* LCD-Data(12) */
- {OFFSET(lcd_data13), (MODE(0) | PULLUDDIS)}, /* LCD-Data(13) */
- {OFFSET(lcd_data14), (MODE(0) | PULLUDDIS)}, /* LCD-Data(14) */
- {OFFSET(lcd_data15), (MODE(0) | PULLUDDIS)}, /* LCD-Data(15) */
-
- {OFFSET(gpmc_ad8), (MODE(1) | PULLUDDIS)}, /* LCD-Data(16) */
- {OFFSET(gpmc_ad9), (MODE(1) | PULLUDDIS)}, /* LCD-Data(17) */
- {OFFSET(gpmc_ad10), (MODE(1) | PULLUDDIS)}, /* LCD-Data(18) */
- {OFFSET(gpmc_ad11), (MODE(1) | PULLUDDIS)}, /* LCD-Data(19) */
- {OFFSET(gpmc_ad12), (MODE(1) | PULLUDDIS)}, /* LCD-Data(20) */
- {OFFSET(gpmc_ad13), (MODE(1) | PULLUDDIS)}, /* LCD-Data(21) */
- {OFFSET(gpmc_ad14), (MODE(1) | PULLUDDIS)}, /* LCD-Data(22) */
- {OFFSET(gpmc_ad15), (MODE(1) | PULLUDDIS)}, /* LCD-Data(23) */
-
- {OFFSET(lcd_vsync), (MODE(0) | PULLUDDIS)}, /* LCD-VSync */
- {OFFSET(lcd_hsync), (MODE(0) | PULLUDDIS)}, /* LCD-HSync */
- {OFFSET(lcd_ac_bias_en), (MODE(0) | PULLUDDIS)},/* LCD-DE */
- {OFFSET(lcd_pclk), (MODE(0) | PULLUDDIS)}, /* LCD-CLK */
-
- {-1},
-};
-
-void enable_uart0_pin_mux(void)
-{
- configure_module_pin_mux(uart0_pin_mux);
-}
-
-void enable_i2c_pin_mux(void)
-{
- configure_module_pin_mux(i2c0_pin_mux);
-}
-
-void enable_board_pin_mux(void)
-{
- configure_module_pin_mux(i2c0_pin_mux);
- configure_module_pin_mux(mii1_pin_mux);
- configure_module_pin_mux(mii2_pin_mux);
-#ifdef CONFIG_NAND
- configure_module_pin_mux(nand_pin_mux);
-#elif defined(CONFIG_MMC)
- configure_module_pin_mux(mmc1_pin_mux);
-#endif
- configure_module_pin_mux(spi0_pin_mux);
- configure_module_pin_mux(lcd_pin_mux);
- configure_module_pin_mux(uart1_pin_mux);
- configure_module_pin_mux(gpIOs);
-}
--- /dev/null
+CONFIG_ARM=y
+CONFIG_TARGET_BRPPT1=y
+CONFIG_SPL=y
+CONFIG_OF_BOARD_SETUP=y
+CONFIG_SYS_EXTRA_OPTIONS="SERIAL1,CONS_INDEX=1,EMMC_BOOT"
+CONFIG_BOOTDELAY=0
+CONFIG_HUSH_PARSER=y
+CONFIG_CMD_BOOTZ=y
+# CONFIG_CMD_IMI is not set
+# CONFIG_CMD_IMLS is not set
+# CONFIG_CMD_XIMG is not set
+# CONFIG_CMD_EDITENV is not set
+# CONFIG_CMD_CRC32 is not set
+# CONFIG_CMD_LOADB is not set
+# CONFIG_CMD_LOADS is not set
+# CONFIG_CMD_FLASH is not set
+CONFIG_CMD_MMC=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_USB=y
+# CONFIG_CMD_FPGA is not set
+CONFIG_CMD_GPIO=y
+# CONFIG_CMD_ITEST is not set
+# CONFIG_CMD_SETEXPR is not set
+CONFIG_CMD_DHCP=y
+# CONFIG_CMD_NFS is not set
+CONFIG_CMD_PING=y
+CONFIG_CMD_TIME=y
+CONFIG_CMD_EXT4=y
+CONFIG_CMD_EXT4_WRITE=y
+CONFIG_CMD_FAT=y
+CONFIG_CMD_FS_GENERIC=y
+CONFIG_NETCONSOLE=y
+CONFIG_SYS_NS16550=y
+CONFIG_USB=y
+CONFIG_USB_MUSB_HOST=y
+CONFIG_USB_STORAGE=y
+CONFIG_OF_LIBFDT=y
--- /dev/null
+CONFIG_ARM=y
+CONFIG_TARGET_BRPPT1=y
+CONFIG_SPL=y
+CONFIG_OF_BOARD_SETUP=y
+CONFIG_SYS_EXTRA_OPTIONS="SERIAL1,CONS_INDEX=1,NAND"
+CONFIG_BOOTDELAY=0
+CONFIG_HUSH_PARSER=y
+CONFIG_CMD_BOOTZ=y
+# CONFIG_CMD_IMI is not set
+# CONFIG_CMD_IMLS is not set
+# CONFIG_CMD_XIMG is not set
+# CONFIG_CMD_EDITENV is not set
+# CONFIG_CMD_CRC32 is not set
+# CONFIG_CMD_LOADB is not set
+# CONFIG_CMD_LOADS is not set
+# CONFIG_CMD_FLASH is not set
+CONFIG_CMD_NAND=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_USB=y
+# CONFIG_CMD_FPGA is not set
+CONFIG_CMD_GPIO=y
+# CONFIG_CMD_ITEST is not set
+# CONFIG_CMD_SETEXPR is not set
+CONFIG_CMD_DHCP=y
+# CONFIG_CMD_NFS is not set
+CONFIG_CMD_PING=y
+CONFIG_CMD_TIME=y
+CONFIG_CMD_EXT4=y
+CONFIG_CMD_EXT4_WRITE=y
+CONFIG_CMD_FAT=y
+CONFIG_CMD_FS_GENERIC=y
+CONFIG_NETCONSOLE=y
+CONFIG_SYS_NS16550=y
+CONFIG_USB=y
+CONFIG_USB_MUSB_HOST=y
+CONFIG_USB_STORAGE=y
+CONFIG_OF_LIBFDT=y
--- /dev/null
+CONFIG_ARM=y
+CONFIG_TARGET_BRPPT1=y
+CONFIG_SPL=y
+CONFIG_OF_BOARD_SETUP=y
+CONFIG_SYS_EXTRA_OPTIONS="SERIAL1,CONS_INDEX=1,SPI_BOOT,EMMC_BOOT"
+CONFIG_BOOTDELAY=0
+CONFIG_HUSH_PARSER=y
+CONFIG_CMD_BOOTZ=y
+# CONFIG_CMD_IMI is not set
+# CONFIG_CMD_IMLS is not set
+# CONFIG_CMD_XIMG is not set
+# CONFIG_CMD_EDITENV is not set
+# CONFIG_CMD_CRC32 is not set
+# CONFIG_CMD_LOADB is not set
+# CONFIG_CMD_LOADS is not set
+# CONFIG_CMD_FLASH is not set
+CONFIG_CMD_MMC=y
+CONFIG_CMD_SF=y
+CONFIG_CMD_SPI=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_USB=y
+# CONFIG_CMD_FPGA is not set
+CONFIG_CMD_GPIO=y
+# CONFIG_CMD_ITEST is not set
+# CONFIG_CMD_SETEXPR is not set
+CONFIG_CMD_DHCP=y
+# CONFIG_CMD_NFS is not set
+CONFIG_CMD_PING=y
+CONFIG_CMD_TIME=y
+CONFIG_CMD_EXT4=y
+CONFIG_CMD_EXT4_WRITE=y
+CONFIG_CMD_FAT=y
+CONFIG_CMD_FS_GENERIC=y
+CONFIG_NETCONSOLE=y
+CONFIG_SPI_FLASH=y
+CONFIG_SPI_FLASH_STMICRO=y
+# CONFIG_SPI_FLASH_USE_4K_SECTORS is not set
+CONFIG_SYS_NS16550=y
+CONFIG_USB=y
+CONFIG_USB_MUSB_HOST=y
+CONFIG_USB_STORAGE=y
+CONFIG_OF_LIBFDT=y
+++ /dev/null
-CONFIG_ARM=y
-CONFIG_TARGET_TSERIES=y
-CONFIG_SPL=y
-CONFIG_OF_BOARD_SETUP=y
-CONFIG_SYS_EXTRA_OPTIONS="SERIAL1,CONS_INDEX=1,EMMC_BOOT"
-CONFIG_BOOTDELAY=0
-CONFIG_HUSH_PARSER=y
-CONFIG_CMD_BOOTZ=y
-# CONFIG_CMD_IMI is not set
-# CONFIG_CMD_IMLS is not set
-# CONFIG_CMD_XIMG is not set
-# CONFIG_CMD_EDITENV is not set
-# CONFIG_CMD_CRC32 is not set
-# CONFIG_CMD_LOADB is not set
-# CONFIG_CMD_LOADS is not set
-# CONFIG_CMD_FLASH is not set
-CONFIG_CMD_MMC=y
-CONFIG_CMD_I2C=y
-CONFIG_CMD_USB=y
-# CONFIG_CMD_FPGA is not set
-CONFIG_CMD_GPIO=y
-# CONFIG_CMD_ITEST is not set
-# CONFIG_CMD_SETEXPR is not set
-CONFIG_CMD_DHCP=y
-# CONFIG_CMD_NFS is not set
-CONFIG_CMD_PING=y
-CONFIG_CMD_TIME=y
-CONFIG_CMD_EXT4=y
-CONFIG_CMD_EXT4_WRITE=y
-CONFIG_CMD_FAT=y
-CONFIG_CMD_FS_GENERIC=y
-CONFIG_NETCONSOLE=y
-CONFIG_SYS_NS16550=y
-CONFIG_USB=y
-CONFIG_USB_MUSB_HOST=y
-CONFIG_USB_STORAGE=y
-CONFIG_OF_LIBFDT=y
+++ /dev/null
-CONFIG_ARM=y
-CONFIG_TARGET_TSERIES=y
-CONFIG_SPL=y
-CONFIG_OF_BOARD_SETUP=y
-CONFIG_SYS_EXTRA_OPTIONS="SERIAL1,CONS_INDEX=1,NAND"
-CONFIG_BOOTDELAY=0
-CONFIG_HUSH_PARSER=y
-CONFIG_CMD_BOOTZ=y
-# CONFIG_CMD_IMI is not set
-# CONFIG_CMD_IMLS is not set
-# CONFIG_CMD_XIMG is not set
-# CONFIG_CMD_EDITENV is not set
-# CONFIG_CMD_CRC32 is not set
-# CONFIG_CMD_LOADB is not set
-# CONFIG_CMD_LOADS is not set
-# CONFIG_CMD_FLASH is not set
-CONFIG_CMD_NAND=y
-CONFIG_CMD_I2C=y
-CONFIG_CMD_USB=y
-# CONFIG_CMD_FPGA is not set
-CONFIG_CMD_GPIO=y
-# CONFIG_CMD_ITEST is not set
-# CONFIG_CMD_SETEXPR is not set
-CONFIG_CMD_DHCP=y
-# CONFIG_CMD_NFS is not set
-CONFIG_CMD_PING=y
-CONFIG_CMD_TIME=y
-CONFIG_CMD_EXT4=y
-CONFIG_CMD_EXT4_WRITE=y
-CONFIG_CMD_FAT=y
-CONFIG_CMD_FS_GENERIC=y
-CONFIG_NETCONSOLE=y
-CONFIG_SYS_NS16550=y
-CONFIG_USB=y
-CONFIG_USB_MUSB_HOST=y
-CONFIG_USB_STORAGE=y
-CONFIG_OF_LIBFDT=y
+++ /dev/null
-CONFIG_ARM=y
-CONFIG_TARGET_TSERIES=y
-CONFIG_SPL=y
-CONFIG_OF_BOARD_SETUP=y
-CONFIG_SYS_EXTRA_OPTIONS="SERIAL1,CONS_INDEX=1,SPI_BOOT,EMMC_BOOT"
-CONFIG_BOOTDELAY=0
-CONFIG_HUSH_PARSER=y
-CONFIG_CMD_BOOTZ=y
-# CONFIG_CMD_IMI is not set
-# CONFIG_CMD_IMLS is not set
-# CONFIG_CMD_XIMG is not set
-# CONFIG_CMD_EDITENV is not set
-# CONFIG_CMD_CRC32 is not set
-# CONFIG_CMD_LOADB is not set
-# CONFIG_CMD_LOADS is not set
-# CONFIG_CMD_FLASH is not set
-CONFIG_CMD_MMC=y
-CONFIG_CMD_SF=y
-CONFIG_CMD_SPI=y
-CONFIG_CMD_I2C=y
-CONFIG_CMD_USB=y
-# CONFIG_CMD_FPGA is not set
-CONFIG_CMD_GPIO=y
-# CONFIG_CMD_ITEST is not set
-# CONFIG_CMD_SETEXPR is not set
-CONFIG_CMD_DHCP=y
-# CONFIG_CMD_NFS is not set
-CONFIG_CMD_PING=y
-CONFIG_CMD_TIME=y
-CONFIG_CMD_EXT4=y
-CONFIG_CMD_EXT4_WRITE=y
-CONFIG_CMD_FAT=y
-CONFIG_CMD_FS_GENERIC=y
-CONFIG_NETCONSOLE=y
-CONFIG_SPI_FLASH=y
-CONFIG_SPI_FLASH_STMICRO=y
-# CONFIG_SPI_FLASH_USE_4K_SECTORS is not set
-CONFIG_SYS_NS16550=y
-CONFIG_USB=y
-CONFIG_USB_MUSB_HOST=y
-CONFIG_USB_STORAGE=y
-CONFIG_OF_LIBFDT=y
--- /dev/null
+/*
+ * brtpp1.h
+ *
+ * specific parts for B&R T-Series Motherboard
+ *
+ * Copyright (C) 2013 Hannes Schmelzer <oe5hpm@oevsv.at> -
+ * Bernecker & Rainer Industrieelektronik GmbH - http://www.br-automation.com
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __CONFIG_BRPPT1_H__
+#define __CONFIG_BRPPT1_H__
+
+#include <configs/bur_cfg_common.h>
+#include <configs/bur_am335x_common.h>
+/* ------------------------------------------------------------------------- */
+#define CONFIG_AM335X_LCD
+#define CONFIG_LCD
+#define CONFIG_LCD_ROTATION
+#define CONFIG_LCD_DT_SIMPLEFB
+#define CONFIG_SYS_WHITE_ON_BLACK
+#define LCD_BPP LCD_COLOR32
+
+#define CONFIG_HW_WATCHDOG
+#define CONFIG_OMAP_WATCHDOG
+#define CONFIG_SPL_WATCHDOG_SUPPORT
+
+#define CONFIG_SPL_GPIO_SUPPORT
+/* Bootcount using the RTC block */
+#define CONFIG_SYS_BOOTCOUNT_ADDR 0x44E3E000
+#define CONFIG_BOOTCOUNT_LIMIT
+#define CONFIG_BOOTCOUNT_AM33XX
+
+/* memory */
+#define CONFIG_SYS_MALLOC_LEN (5 * 1024 * 1024)
+
+/* Clock Defines */
+#define V_OSCK 26000000 /* Clock output from T2 */
+#define V_SCLK (V_OSCK)
+
+#define CONFIG_POWER_TPS65217
+
+/* Support both device trees and ATAGs. */
+#define CONFIG_USE_FDT /* use fdt within board code */
+#define CONFIG_CMDLINE_TAG
+#define CONFIG_SETUP_MEMORY_TAGS
+#define CONFIG_INITRD_TAG
+/*#define CONFIG_MACH_TYPE 3589*/
+#define CONFIG_MACH_TYPE 0xFFFFFFFF /* TODO: check with kernel*/
+
+/* MMC/SD IP block */
+#if defined(CONFIG_EMMC_BOOT)
+ #define CONFIG_MMC
+ #define CONFIG_GENERIC_MMC
+ #define CONFIG_OMAP_HSMMC
+ #define CONFIG_SUPPORT_EMMC_BOOT
+/* RAW SD card / eMMC locations. */
+ #define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x300 /*addr. 0x60000 */
+ #define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x200 /* 256 KB */
+ #define CONFIG_SPL_MMC_SUPPORT
+#endif /* CONFIG_EMMC_BOOT */
+
+/*
+ * When we have SPI or NAND flash we expect to be making use of mtdparts,
+ * both for ease of use in U-Boot and for passing information on to
+ * the Linux kernel.
+ */
+#if defined(CONFIG_SPI_BOOT) || defined(CONFIG_NAND)
+#define CONFIG_MTD_DEVICE /* Required for mtdparts */
+#define CONFIG_CMD_MTDPARTS
+#endif /* CONFIG_SPI_BOOT, ... */
+
+#undef CONFIG_SPL_OS_BOOT
+#ifdef CONFIG_SPL_OS_BOOT
+#define CONFIG_SYS_SPL_ARGS_ADDR 0x80F80000
+
+/* RAW SD card / eMMC */
+#define CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR 0x900 /* address 0x120000 */
+#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR 0x80 /* address 0x10000 */
+#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS 0x80 /* 64KiB */
+
+/* NAND */
+#ifdef CONFIG_NAND
+#define CONFIG_CMD_SPL_NAND_OFS 0x080000 /* end of u-boot */
+#define CONFIG_SYS_NAND_SPL_KERNEL_OFFS 0x140000
+#define CONFIG_CMD_SPL_WRITE_SIZE 0x2000
+#endif /* CONFIG_NAND */
+#endif /* CONFIG_SPL_OS_BOOT */
+
+#ifdef CONFIG_NAND
+#define CONFIG_SPL_NAND_AM33XX_BCH /* OMAP4 and later ELM support */
+#define CONFIG_SPL_NAND_SUPPORT
+#define CONFIG_SPL_NAND_BASE
+#define CONFIG_SPL_NAND_DRIVERS
+#define CONFIG_SPL_NAND_ECC
+#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE
+#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000
+#endif /* CONFIG_NAND */
+
+/* Always 64 KiB env size */
+#define CONFIG_ENV_SIZE (64 << 10)
+
+#ifdef CONFIG_NAND
+#define NANDARGS \
+ "mtdids=" MTDIDS_DEFAULT "\0" \
+ "mtdparts=" MTDPARTS_DEFAULT "\0" \
+ "nandargs=setenv bootargs console=${console} " \
+ "${optargs} " \
+ "${optargs_rot} " \
+ "root=mtd6 " \
+ "rootfstype=jffs2\0" \
+ "kernelsize=0x400000\0" \
+ "nandboot=echo booting from nand ...; " \
+ "run nandargs; " \
+ "nand read ${loadaddr} kernel ${kernelsize}; " \
+ "bootz ${loadaddr} - ${dtbaddr}\0" \
+ "defboot=run nandboot\0" \
+ "bootlimit=1\0" \
+ "simplefb=1\0 " \
+ "altbootcmd=run usbscript\0"
+#else
+#define NANDARGS ""
+#endif /* CONFIG_NAND */
+
+#ifdef CONFIG_MMC
+#define MMCARGS \
+"dtbdev=mmc\0" \
+"dtbpart=0:1\0" \
+"mmcroot0=setenv bootargs ${optargs_rot} ${optargs} console=${console}\0" \
+"mmcroot1=setenv bootargs ${optargs_rot} ${optargs} console=${console} " \
+ "root=/dev/mmcblk0p2 rootfstype=ext4\0" \
+"mmcboot0=echo booting Updatesystem from mmc (ext4-fs) ...; " \
+ "setenv simplefb 1; " \
+ "ext4load mmc 0:1 ${loadaddr} /${kernel}; " \
+ "ext4load mmc 0:1 ${ramaddr} /${ramdisk}; " \
+ "run mmcroot0; bootz ${loadaddr} ${ramaddr} ${dtbaddr};\0" \
+"mmcboot1=echo booting PPT-OS from mmc (ext4-fs) ...; " \
+ "setenv simplefb 0; " \
+ "ext4load mmc 0:2 ${loadaddr} /boot/${kernel}; " \
+ "run mmcroot1; bootz ${loadaddr} - ${dtbaddr};\0" \
+"defboot=ext4load mmc 0:2 ${loadaddr} /boot/PPTImage.md5 && run mmcboot1; " \
+ "ext4load mmc 0:1 ${dtbaddr} /$dtb && run mmcboot0; " \
+ "run ramboot; run usbscript;\0" \
+"bootlimit=1\0" \
+"altbootcmd=run mmcboot0;\0" \
+"upduboot=dhcp; " \
+ "tftp ${loadaddr} MLO && mmc write ${loadaddr} 100 100; " \
+ "tftp ${loadaddr} u-boot.img && mmc write ${loadaddr} 300 400;\0"
+#else
+#define MMCARGS ""
+#endif /* CONFIG_MMC */
+
+#ifndef CONFIG_SPL_BUILD
+#define CONFIG_EXTRA_ENV_SETTINGS \
+BUR_COMMON_ENV \
+"verify=no\0" \
+"autoload=0\0" \
+"dtb=bur-ppt-ts30.dtb\0" \
+"dtbaddr=0x80100000\0" \
+"loadaddr=0x80200000\0" \
+"ramaddr=0x80A00000\0" \
+"kernel=zImage\0" \
+"ramdisk=rootfs.cpio.uboot\0" \
+"console=ttyO0,115200n8\0" \
+"optargs=consoleblank=0 quiet panic=2\0" \
+"nfsroot=/tftpboot/tseries/rootfs-small\0" \
+"nfsopts=nolock\0" \
+"ramargs=setenv bootargs ${optargs} console=${console} root=/dev/ram0\0" \
+"netargs=setenv bootargs console=${console} " \
+ "${optargs} " \
+ "root=/dev/nfs " \
+ "nfsroot=${serverip}:${nfsroot},${nfsopts} rw " \
+ "ip=dhcp\0" \
+"netboot=echo Booting from network ...; " \
+ "dhcp; " \
+ "tftp ${loadaddr} ${kernel}; " \
+ "tftp ${dtbaddr} ${dtb}; " \
+ "run netargs; " \
+ "bootz ${loadaddr} - ${dtbaddr}\0" \
+"ramboot=echo Booting from network into RAM ...; "\
+ "if dhcp; then; " \
+ "tftp ${loadaddr} ${kernel}; " \
+ "tftp ${ramaddr} ${ramdisk}; " \
+ "if ext4load ${dtbdev} ${dtbpart} ${dtbaddr} /${dtb}; " \
+ "then; else tftp ${dtbaddr} ${dtb}; fi;" \
+ "run mmcroot0; " \
+ "bootz ${loadaddr} ${ramaddr} ${dtbaddr}; fi;\0" \
+"netupdate=echo Updating UBOOT from Network (TFTP) ...; " \
+ "setenv autoload 0; " \
+ "dhcp && tftp 0x80000000 updateUBOOT.img && source;\0" \
+NANDARGS \
+MMCARGS
+#endif /* !CONFIG_SPL_BUILD*/
+
+#define CONFIG_BOOTCOMMAND \
+ "run defboot;"
+
+#ifdef CONFIG_NAND
+/*
+ * GPMC block. We support 1 device and the physical address to
+ * access CS0 at is 0x8000000.
+ */
+#define CONFIG_SYS_MAX_NAND_DEVICE 1
+#define CONFIG_SYS_NAND_BASE 0x8000000
+#define CONFIG_NAND_OMAP_GPMC
+/* don't change OMAP_ELM, ECCSCHEME. ROM code only supports this */
+#define CONFIG_NAND_OMAP_ELM
+#define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_BCH8_CODE_HW
+#define CONFIG_SYS_NAND_5_ADDR_CYCLE
+#define CONFIG_SYS_NAND_BLOCK_SIZE (128*1024)
+#define CONFIG_SYS_NAND_PAGE_SIZE 2048
+#define CONFIG_SYS_NAND_PAGE_COUNT (CONFIG_SYS_NAND_BLOCK_SIZE / \
+ CONFIG_SYS_NAND_PAGE_SIZE)
+#define CONFIG_SYS_NAND_OOBSIZE 64
+#define CONFIG_SYS_NAND_BAD_BLOCK_POS NAND_LARGE_BADBLOCK_POS
+#define CONFIG_SYS_NAND_ECCPOS {2, 3, 4, 5, 6, 7, 8, 9, \
+ 10, 11, 12, 13, 14, 15, 16, 17, \
+ 18, 19, 20, 21, 22, 23, 24, 25, \
+ 26, 27, 28, 29, 30, 31, 32, 33, \
+ 34, 35, 36, 37, 38, 39, 40, 41, \
+ 42, 43, 44, 45, 46, 47, 48, 49, \
+ 50, 51, 52, 53, 54, 55, 56, 57, }
+
+#define CONFIG_SYS_NAND_ECCSIZE 512
+#define CONFIG_SYS_NAND_ECCBYTES 14
+
+#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE
+#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000
+
+#define MTDIDS_DEFAULT "nand0=omap2-nand.0"
+#define MTDPARTS_DEFAULT "mtdparts=omap2-nand.0:" \
+ "128k(MLO)," \
+ "128k(MLO.backup)," \
+ "128k(dtb)," \
+ "128k(u-boot-env)," \
+ "512k(u-boot)," \
+ "4m(kernel),"\
+ "128m(rootfs),"\
+ "-(user)"
+#define CONFIG_NAND_OMAP_GPMC_WSCFG 1
+#endif /* CONFIG_NAND */
+
+/* USB configuration */
+#define CONFIG_USB_MUSB_DSPS
+#define CONFIG_ARCH_MISC_INIT
+#define CONFIG_USB_MUSB_PIO_ONLY
+#define CONFIG_USB_MUSB_DISABLE_BULK_COMBINE_SPLIT
+#define CONFIG_AM335X_USB0
+#define CONFIG_AM335X_USB0_MODE MUSB_HOST
+#define CONFIG_AM335X_USB1
+#define CONFIG_AM335X_USB1_MODE MUSB_HOST
+
+#if defined(CONFIG_SPI_BOOT)
+/* McSPI IP block */
+#define CONFIG_SPI
+#define CONFIG_OMAP3_SPI
+#define CONFIG_SF_DEFAULT_SPEED 24000000
+
+#define CONFIG_SPL_SPI_SUPPORT
+#define CONFIG_SPL_SPI_FLASH_SUPPORT
+#define CONFIG_SPL_SPI_LOAD
+#define CONFIG_SYS_SPI_U_BOOT_OFFS 0x20000
+#undef CONFIG_ENV_IS_NOWHERE
+#define CONFIG_ENV_IS_IN_SPI_FLASH
+#define CONFIG_SYS_REDUNDAND_ENVIRONMENT
+#define CONFIG_ENV_SPI_MAX_HZ CONFIG_SF_DEFAULT_SPEED
+#define CONFIG_ENV_SECT_SIZE (4 << 10) /* 4 KB sectors */
+#define CONFIG_ENV_OFFSET (768 << 10) /* 768 KiB in */
+#define CONFIG_ENV_OFFSET_REDUND (896 << 10) /* 896 KiB in */
+
+#elif defined(CONFIG_EMMC_BOOT)
+#undef CONFIG_ENV_IS_NOWHERE
+#define CONFIG_ENV_IS_IN_MMC
+#define CONFIG_SYS_MMC_ENV_DEV 0
+#define CONFIG_SYS_MMC_ENV_PART 2
+#define CONFIG_ENV_OFFSET 0x40000 /* TODO: Adresse definieren */
+#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)
+#define CONFIG_SYS_REDUNDAND_ENVIRONMENT
+
+#elif defined(CONFIG_NAND)
+/* No NAND env support in SPL */
+#ifdef CONFIG_SPL_BUILD
+#define CONFIG_ENV_IS_NOWHERE
+#else
+#define CONFIG_ENV_IS_IN_NAND
+#endif
+#define CONFIG_ENV_OFFSET 0x60000
+#define CONFIG_SYS_ENV_SECT_SIZE CONFIG_ENV_SIZE
+#else
+#error "no storage for Environment defined!"
+#endif
+/*
+ * Common filesystems support. When we have removable storage we
+ * enabled a number of useful commands and support.
+ */
+#if defined(CONFIG_MMC) || defined(CONFIG_USB_STORAGE)
+#define CONFIG_DOS_PARTITION
+#define CONFIG_FAT_WRITE
+#define CONFIG_FS_EXT4
+#define CONFIG_EXT4_WRITE
+#endif /* CONFIG_MMC, ... */
+
+#endif /* ! __CONFIG_BRPPT1_H__ */
+++ /dev/null
-/*
- * tseries.h
- *
- * specific parts for B&R T-Series Motherboard
- *
- * Copyright (C) 2013 Hannes Schmelzer <oe5hpm@oevsv.at> -
- * Bernecker & Rainer Industrieelektronik GmbH - http://www.br-automation.com
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#ifndef __CONFIG_TSERIES_H__
-#define __CONFIG_TSERIES_H__
-
-#include <configs/bur_cfg_common.h>
-#include <configs/bur_am335x_common.h>
-/* ------------------------------------------------------------------------- */
-#define CONFIG_AM335X_LCD
-#define CONFIG_LCD
-#define CONFIG_LCD_ROTATION
-#define CONFIG_LCD_DT_SIMPLEFB
-#define CONFIG_SYS_WHITE_ON_BLACK
-#define LCD_BPP LCD_COLOR32
-
-#define CONFIG_HW_WATCHDOG
-#define CONFIG_OMAP_WATCHDOG
-#define CONFIG_SPL_WATCHDOG_SUPPORT
-
-#define CONFIG_SPL_GPIO_SUPPORT
-/* Bootcount using the RTC block */
-#define CONFIG_SYS_BOOTCOUNT_ADDR 0x44E3E000
-#define CONFIG_BOOTCOUNT_LIMIT
-#define CONFIG_BOOTCOUNT_AM33XX
-
-/* memory */
-#define CONFIG_SYS_MALLOC_LEN (5 * 1024 * 1024)
-
-/* Clock Defines */
-#define V_OSCK 26000000 /* Clock output from T2 */
-#define V_SCLK (V_OSCK)
-
-#define CONFIG_POWER_TPS65217
-
-/* Support both device trees and ATAGs. */
-#define CONFIG_USE_FDT /* use fdt within board code */
-#define CONFIG_CMDLINE_TAG
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_INITRD_TAG
-/*#define CONFIG_MACH_TYPE 3589*/
-#define CONFIG_MACH_TYPE 0xFFFFFFFF /* TODO: check with kernel*/
-
-/* MMC/SD IP block */
-#if defined(CONFIG_EMMC_BOOT)
- #define CONFIG_MMC
- #define CONFIG_GENERIC_MMC
- #define CONFIG_OMAP_HSMMC
- #define CONFIG_SUPPORT_EMMC_BOOT
-/* RAW SD card / eMMC locations. */
- #define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x300 /*addr. 0x60000 */
- #define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x200 /* 256 KB */
- #define CONFIG_SPL_MMC_SUPPORT
-#endif /* CONFIG_EMMC_BOOT */
-
-/*
- * When we have SPI or NAND flash we expect to be making use of mtdparts,
- * both for ease of use in U-Boot and for passing information on to
- * the Linux kernel.
- */
-#if defined(CONFIG_SPI_BOOT) || defined(CONFIG_NAND)
-#define CONFIG_MTD_DEVICE /* Required for mtdparts */
-#define CONFIG_CMD_MTDPARTS
-#endif /* CONFIG_SPI_BOOT, ... */
-
-#undef CONFIG_SPL_OS_BOOT
-#ifdef CONFIG_SPL_OS_BOOT
-#define CONFIG_SYS_SPL_ARGS_ADDR 0x80F80000
-
-/* RAW SD card / eMMC */
-#define CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR 0x900 /* address 0x120000 */
-#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR 0x80 /* address 0x10000 */
-#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS 0x80 /* 64KiB */
-
-/* NAND */
-#ifdef CONFIG_NAND
-#define CONFIG_CMD_SPL_NAND_OFS 0x080000 /* end of u-boot */
-#define CONFIG_SYS_NAND_SPL_KERNEL_OFFS 0x140000
-#define CONFIG_CMD_SPL_WRITE_SIZE 0x2000
-#endif /* CONFIG_NAND */
-#endif /* CONFIG_SPL_OS_BOOT */
-
-#ifdef CONFIG_NAND
-#define CONFIG_SPL_NAND_AM33XX_BCH /* OMAP4 and later ELM support */
-#define CONFIG_SPL_NAND_SUPPORT
-#define CONFIG_SPL_NAND_BASE
-#define CONFIG_SPL_NAND_DRIVERS
-#define CONFIG_SPL_NAND_ECC
-#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE
-#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000
-#endif /* CONFIG_NAND */
-
-/* Always 64 KiB env size */
-#define CONFIG_ENV_SIZE (64 << 10)
-
-#ifdef CONFIG_NAND
-#define NANDARGS \
- "mtdids=" MTDIDS_DEFAULT "\0" \
- "mtdparts=" MTDPARTS_DEFAULT "\0" \
- "nandargs=setenv bootargs console=${console} " \
- "${optargs} " \
- "${optargs_rot} " \
- "root=mtd6 " \
- "rootfstype=jffs2\0" \
- "kernelsize=0x400000\0" \
- "nandboot=echo booting from nand ...; " \
- "run nandargs; " \
- "nand read ${loadaddr} kernel ${kernelsize}; " \
- "bootz ${loadaddr} - ${dtbaddr}\0" \
- "defboot=run nandboot\0" \
- "bootlimit=1\0" \
- "simplefb=1\0 " \
- "altbootcmd=run usbscript\0"
-#else
-#define NANDARGS ""
-#endif /* CONFIG_NAND */
-
-#ifdef CONFIG_MMC
-#define MMCARGS \
-"dtbdev=mmc\0" \
-"dtbpart=0:1\0" \
-"mmcroot0=setenv bootargs ${optargs_rot} ${optargs} console=${console}\0" \
-"mmcroot1=setenv bootargs ${optargs_rot} ${optargs} console=${console} " \
- "root=/dev/mmcblk0p2 rootfstype=ext4\0" \
-"mmcboot0=echo booting Updatesystem from mmc (ext4-fs) ...; " \
- "setenv simplefb 1; " \
- "ext4load mmc 0:1 ${loadaddr} /${kernel}; " \
- "ext4load mmc 0:1 ${ramaddr} /${ramdisk}; " \
- "run mmcroot0; bootz ${loadaddr} ${ramaddr} ${dtbaddr};\0" \
-"mmcboot1=echo booting PPT-OS from mmc (ext4-fs) ...; " \
- "setenv simplefb 0; " \
- "ext4load mmc 0:2 ${loadaddr} /boot/${kernel}; " \
- "run mmcroot1; bootz ${loadaddr} - ${dtbaddr};\0" \
-"defboot=ext4load mmc 0:2 ${loadaddr} /boot/PPTImage.md5 && run mmcboot1; " \
- "ext4load mmc 0:1 ${dtbaddr} /$dtb && run mmcboot0; " \
- "run ramboot; run usbscript;\0" \
-"bootlimit=1\0" \
-"altbootcmd=run mmcboot0;\0" \
-"upduboot=dhcp; " \
- "tftp ${loadaddr} MLO && mmc write ${loadaddr} 100 100; " \
- "tftp ${loadaddr} u-boot.img && mmc write ${loadaddr} 300 400;\0"
-#else
-#define MMCARGS ""
-#endif /* CONFIG_MMC */
-
-#ifndef CONFIG_SPL_BUILD
-#define CONFIG_EXTRA_ENV_SETTINGS \
-BUR_COMMON_ENV \
-"verify=no\0" \
-"autoload=0\0" \
-"dtb=bur-ppt-ts30.dtb\0" \
-"dtbaddr=0x80100000\0" \
-"loadaddr=0x80200000\0" \
-"ramaddr=0x80A00000\0" \
-"kernel=zImage\0" \
-"ramdisk=rootfs.cpio.uboot\0" \
-"console=ttyO0,115200n8\0" \
-"optargs=consoleblank=0 quiet panic=2\0" \
-"nfsroot=/tftpboot/tseries/rootfs-small\0" \
-"nfsopts=nolock\0" \
-"ramargs=setenv bootargs ${optargs} console=${console} root=/dev/ram0\0" \
-"netargs=setenv bootargs console=${console} " \
- "${optargs} " \
- "root=/dev/nfs " \
- "nfsroot=${serverip}:${nfsroot},${nfsopts} rw " \
- "ip=dhcp\0" \
-"netboot=echo Booting from network ...; " \
- "dhcp; " \
- "tftp ${loadaddr} ${kernel}; " \
- "tftp ${dtbaddr} ${dtb}; " \
- "run netargs; " \
- "bootz ${loadaddr} - ${dtbaddr}\0" \
-"ramboot=echo Booting from network into RAM ...; "\
- "if dhcp; then; " \
- "tftp ${loadaddr} ${kernel}; " \
- "tftp ${ramaddr} ${ramdisk}; " \
- "if ext4load ${dtbdev} ${dtbpart} ${dtbaddr} /${dtb}; " \
- "then; else tftp ${dtbaddr} ${dtb}; fi;" \
- "run mmcroot0; " \
- "bootz ${loadaddr} ${ramaddr} ${dtbaddr}; fi;\0" \
-"netupdate=echo Updating UBOOT from Network (TFTP) ...; " \
- "setenv autoload 0; " \
- "dhcp && tftp 0x80000000 updateUBOOT.img && source;\0" \
-NANDARGS \
-MMCARGS
-#endif /* !CONFIG_SPL_BUILD*/
-
-#define CONFIG_BOOTCOMMAND \
- "run defboot;"
-
-#ifdef CONFIG_NAND
-/*
- * GPMC block. We support 1 device and the physical address to
- * access CS0 at is 0x8000000.
- */
-#define CONFIG_SYS_MAX_NAND_DEVICE 1
-#define CONFIG_SYS_NAND_BASE 0x8000000
-#define CONFIG_NAND_OMAP_GPMC
-/* don't change OMAP_ELM, ECCSCHEME. ROM code only supports this */
-#define CONFIG_NAND_OMAP_ELM
-#define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_BCH8_CODE_HW
-#define CONFIG_SYS_NAND_5_ADDR_CYCLE
-#define CONFIG_SYS_NAND_BLOCK_SIZE (128*1024)
-#define CONFIG_SYS_NAND_PAGE_SIZE 2048
-#define CONFIG_SYS_NAND_PAGE_COUNT (CONFIG_SYS_NAND_BLOCK_SIZE / \
- CONFIG_SYS_NAND_PAGE_SIZE)
-#define CONFIG_SYS_NAND_OOBSIZE 64
-#define CONFIG_SYS_NAND_BAD_BLOCK_POS NAND_LARGE_BADBLOCK_POS
-#define CONFIG_SYS_NAND_ECCPOS {2, 3, 4, 5, 6, 7, 8, 9, \
- 10, 11, 12, 13, 14, 15, 16, 17, \
- 18, 19, 20, 21, 22, 23, 24, 25, \
- 26, 27, 28, 29, 30, 31, 32, 33, \
- 34, 35, 36, 37, 38, 39, 40, 41, \
- 42, 43, 44, 45, 46, 47, 48, 49, \
- 50, 51, 52, 53, 54, 55, 56, 57, }
-
-#define CONFIG_SYS_NAND_ECCSIZE 512
-#define CONFIG_SYS_NAND_ECCBYTES 14
-
-#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE
-#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000
-
-#define MTDIDS_DEFAULT "nand0=omap2-nand.0"
-#define MTDPARTS_DEFAULT "mtdparts=omap2-nand.0:" \
- "128k(MLO)," \
- "128k(MLO.backup)," \
- "128k(dtb)," \
- "128k(u-boot-env)," \
- "512k(u-boot)," \
- "4m(kernel),"\
- "128m(rootfs),"\
- "-(user)"
-#define CONFIG_NAND_OMAP_GPMC_WSCFG 1
-#endif /* CONFIG_NAND */
-
-/* USB configuration */
-#define CONFIG_USB_MUSB_DSPS
-#define CONFIG_ARCH_MISC_INIT
-#define CONFIG_USB_MUSB_PIO_ONLY
-#define CONFIG_USB_MUSB_DISABLE_BULK_COMBINE_SPLIT
-#define CONFIG_AM335X_USB0
-#define CONFIG_AM335X_USB0_MODE MUSB_HOST
-#define CONFIG_AM335X_USB1
-#define CONFIG_AM335X_USB1_MODE MUSB_HOST
-
-#if defined(CONFIG_SPI_BOOT)
-/* McSPI IP block */
-#define CONFIG_SPI
-#define CONFIG_OMAP3_SPI
-#define CONFIG_SF_DEFAULT_SPEED 24000000
-
-#define CONFIG_SPL_SPI_SUPPORT
-#define CONFIG_SPL_SPI_FLASH_SUPPORT
-#define CONFIG_SPL_SPI_LOAD
-#define CONFIG_SYS_SPI_U_BOOT_OFFS 0x20000
-#undef CONFIG_ENV_IS_NOWHERE
-#define CONFIG_ENV_IS_IN_SPI_FLASH
-#define CONFIG_SYS_REDUNDAND_ENVIRONMENT
-#define CONFIG_ENV_SPI_MAX_HZ CONFIG_SF_DEFAULT_SPEED
-#define CONFIG_ENV_SECT_SIZE (4 << 10) /* 4 KB sectors */
-#define CONFIG_ENV_OFFSET (768 << 10) /* 768 KiB in */
-#define CONFIG_ENV_OFFSET_REDUND (896 << 10) /* 896 KiB in */
-
-#elif defined(CONFIG_EMMC_BOOT)
-#undef CONFIG_ENV_IS_NOWHERE
-#define CONFIG_ENV_IS_IN_MMC
-#define CONFIG_SYS_MMC_ENV_DEV 0
-#define CONFIG_SYS_MMC_ENV_PART 2
-#define CONFIG_ENV_OFFSET 0x40000 /* TODO: Adresse definieren */
-#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)
-#define CONFIG_SYS_REDUNDAND_ENVIRONMENT
-
-#elif defined(CONFIG_NAND)
-/* No NAND env support in SPL */
-#ifdef CONFIG_SPL_BUILD
-#define CONFIG_ENV_IS_NOWHERE
-#else
-#define CONFIG_ENV_IS_IN_NAND
-#endif
-#define CONFIG_ENV_OFFSET 0x60000
-#define CONFIG_SYS_ENV_SECT_SIZE CONFIG_ENV_SIZE
-#else
-#error "no storage for Environment defined!"
-#endif
-/*
- * Common filesystems support. When we have removable storage we
- * enabled a number of useful commands and support.
- */
-#if defined(CONFIG_MMC) || defined(CONFIG_USB_STORAGE)
-#define CONFIG_DOS_PARTITION
-#define CONFIG_FAT_WRITE
-#define CONFIG_FS_EXT4
-#define CONFIG_EXT4_WRITE
-#endif /* CONFIG_MMC, ... */
-
-#endif /* ! __CONFIG_TSERIES_H__ */
projects / platform / kernel / u-boot.git / commitdiff