[media] marvell-cam: Pass sensor parameters from the platform
authorJonathan Corbet <corbet@lwn.net>
Sat, 11 Jun 2011 17:46:44 +0000 (14:46 -0300)
committerMauro Carvalho Chehab <mchehab@redhat.com>
Wed, 27 Jul 2011 20:53:00 +0000 (17:53 -0300)
Depending on the controller, the ov7670 sensor may be told to work with a
different clock speed or to use the SMBUS protocol.  Remove the wired-in
code and pass that information from the platform layer.  The Cafe driver
now just assumes it's running on an OLPC XO 1; I do not believe it has ever
run anywhere else.

Cc: Daniel Drake <dsd@laptop.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/video/marvell-ccic/cafe-driver.c
drivers/media/video/marvell-ccic/mcam-core.c
drivers/media/video/marvell-ccic/mcam-core.h

index 3f38f2a..08edf95 100644 (file)
@@ -404,6 +404,12 @@ static int cafe_pci_probe(struct pci_dev *pdev,
        mcam->plat_power_down = cafe_ctlr_power_down;
        mcam->dev = &pdev->dev;
        /*
+        * Set the clock speed for the XO 1; I don't believe this
+        * driver has ever run anywhere else.
+        */
+       mcam->clock_speed = 45;
+       mcam->use_smbus = 1;
+       /*
         * Get set up on the PCI bus.
         */
        ret = pci_enable_device(pdev);
index 18fce9e..0d60234 100644 (file)
@@ -7,7 +7,6 @@
 #include <linux/kernel.h>
 #include <linux/module.h>
 #include <linux/fs.h>
-#include <linux/dmi.h>
 #include <linux/mm.h>
 #include <linux/i2c.h>
 #include <linux/interrupt.h>
@@ -1536,22 +1535,7 @@ int mccic_irq(struct mcam_camera *cam, unsigned int irqs)
  * Registration and such.
  */
 
-/* FIXME this is really platform stuff */
-static const struct dmi_system_id olpc_xo1_dmi[] = {
-       {
-               .matches = {
-                       DMI_MATCH(DMI_SYS_VENDOR, "OLPC"),
-                       DMI_MATCH(DMI_PRODUCT_NAME, "XO"),
-                       DMI_MATCH(DMI_PRODUCT_VERSION, "1"),
-               },
-       },
-       { }
-};
-
 static struct ov7670_config sensor_cfg = {
-       /* This controller only does SMBUS */
-       .use_smbus = true,
-
        /*
         * Exclude QCIF mode, because it only captures a tiny portion
         * of the sensor FOV
@@ -1590,13 +1574,11 @@ int mccic_register(struct mcam_camera *cam)
 
        mcam_ctlr_init(cam);
 
-       /* Apply XO-1 clock speed */
-       if (dmi_check_system(olpc_xo1_dmi))
-               sensor_cfg.clock_speed = 45;
-
        /*
         * Try to find the sensor.
         */
+       sensor_cfg.clock_speed = cam->clock_speed;
+       sensor_cfg.use_smbus = cam->use_smbus;
        cam->sensor_addr = ov7670_info.addr;
        cam->sensor = v4l2_i2c_new_subdev_board(&cam->v4l2_dev,
                        &cam->i2c_adapter, &ov7670_info, NULL);
index 0b55b8e..21485e7 100644 (file)
@@ -42,6 +42,8 @@ struct mcam_camera {
        spinlock_t dev_lock;
        struct device *dev; /* For messages, dma alloc */
        unsigned int chip_id;
+       short int clock_speed;  /* Sensor clock speed, default 30 */
+       short int use_smbus;    /* SMBUS or straight I2c? */
 
        /*
         * Callbacks from the core to the platform code.