*/
/dts-v1/;
-#include <dt-bindings/interrupt-controller/irq.h>
-#include <dt-bindings/gpio/gpio.h>
-#include "imx28.dtsi"
+#include "imx28-duckbill-2.dts"
/ {
model = "I2SE Duckbill 2 485";
compatible = "i2se,duckbill-2-485", "i2se,duckbill-2", "fsl,imx28";
- memory@40000000 {
- device_type = "memory";
- reg = <0x40000000 0x08000000>;
- };
-
- apb@80000000 {
- apbh@80000000 {
- ssp0: spi@80010000 {
- compatible = "fsl,imx28-mmc";
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_8bit_pins_a
- &mmc0_cd_cfg &mmc0_sck_cfg>;
- bus-width = <8>;
- vmmc-supply = <®_3p3v>;
- status = "okay";
- non-removable;
- };
-
- ssp2: spi@80014000 {
- compatible = "fsl,imx28-mmc";
- pinctrl-names = "default";
- pinctrl-0 = <&mmc2_4bit_pins_b
- &mmc2_cd_cfg &mmc2_sck_cfg_b>;
- bus-width = <4>;
- vmmc-supply = <®_3p3v>;
- status = "okay";
- };
-
- pinctrl@80018000 {
- pinctrl-names = "default";
- pinctrl-0 = <&hog_pins_a>;
-
- hog_pins_a: hog@0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_LCD_D17__GPIO_1_17 /* Revision detection */
- >;
- fsl,drive-strength = <MXS_DRIVE_4mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_DISABLE>;
- };
-
- mac0_phy_reset_pin: mac0-phy-reset@0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_GPMI_ALE__GPIO_0_26 /* PHY Reset */
- >;
- fsl,drive-strength = <MXS_DRIVE_4mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_DISABLE>;
- };
-
- mac0_phy_int_pin: mac0-phy-int@0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_GPMI_D07__GPIO_0_7 /* PHY Interrupt */
- >;
- fsl,drive-strength = <MXS_DRIVE_4mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_DISABLE>;
- };
-
- led_pins: leds@0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_SAIF0_MCLK__GPIO_3_20
- MX28_PAD_SAIF0_LRCLK__GPIO_3_21
- MX28_PAD_I2C0_SCL__GPIO_3_24
- MX28_PAD_I2C0_SDA__GPIO_3_25
- >;
- fsl,drive-strength = <MXS_DRIVE_4mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_DISABLE>;
- };
- };
- };
-
- apbx@80040000 {
- lradc@80050000 {
- status = "okay";
- };
-
- auart0: serial@8006a000 {
- pinctrl-names = "default";
- pinctrl-0 = <&auart0_2pins_a>;
- status = "okay";
- };
-
- duart: serial@80074000 {
- pinctrl-names = "default";
- pinctrl-0 = <&duart_pins_a>;
- status = "okay";
- };
-
- usbphy0: usbphy@8007c000 {
- status = "okay";
- };
- };
- };
-
- ahb@80080000 {
- usb0: usb@80080000 {
- status = "okay";
- dr_mode = "peripheral";
- };
-
- mac0: ethernet@800f0000 {
- phy-mode = "rmii";
- pinctrl-names = "default";
- pinctrl-0 = <&mac0_pins_a>, <&mac0_phy_reset_pin>;
- phy-supply = <®_3p3v>;
- phy-reset-gpios = <&gpio0 26 GPIO_ACTIVE_LOW>;
- phy-reset-duration = <25>;
- phy-handle = <ðphy>;
- status = "okay";
-
- mdio {
- #address-cells = <1>;
- #size-cells = <0>;
-
- ethphy: ethernet-phy@0 {
- compatible = "ethernet-phy-ieee802.3-c22";
- reg = <0>;
- pinctrl-names = "default";
- pinctrl-0 = <&mac0_phy_int_pin>;
- interrupt-parent = <&gpio0>;
- interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
- max-speed = <100>;
- };
- };
- };
- };
-
- reg_3p3v: regulator-3p3v {
- compatible = "regulator-fixed";
- regulator-name = "3P3V";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-always-on;
- };
-
leds {
- compatible = "gpio-leds";
- pinctrl-names = "default";
- pinctrl-0 = <&led_pins>;
-
- status-red {
- label = "duckbill:red:status";
- gpios = <&gpio3 21 GPIO_ACTIVE_HIGH>;
- linux,default-trigger = "default-on";
- };
-
- status-green {
- label = "duckbill:green:status";
- gpios = <&gpio3 20 GPIO_ACTIVE_HIGH>;
- linux,default-trigger = "heartbeat";
- };
-
rs485-red {
label = "duckbill:red:rs485";
gpios = <&gpio3 24 GPIO_ACTIVE_LOW>;
};
};
};
+
+&i2c0 {
+ status = "disabled";
+};
+
+&led_pins {
+ fsl,pinmux-ids = <
+ MX28_PAD_SAIF0_MCLK__GPIO_3_20
+ MX28_PAD_SAIF0_LRCLK__GPIO_3_21
+ MX28_PAD_I2C0_SCL__GPIO_3_24
+ MX28_PAD_I2C0_SDA__GPIO_3_25
+ >;
+};
*/
/dts-v1/;
-#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/input/input.h>
-#include <dt-bindings/gpio/gpio.h>
-#include "imx28.dtsi"
+#include "imx28-duckbill-2.dts"
/ {
model = "I2SE Duckbill 2 EnOcean";
compatible = "i2se,duckbill-2-enocean", "i2se,duckbill-2", "fsl,imx28";
- memory@40000000 {
- device_type = "memory";
- reg = <0x40000000 0x08000000>;
- };
-
- apb@80000000 {
- apbh@80000000 {
- ssp0: spi@80010000 {
- compatible = "fsl,imx28-mmc";
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_8bit_pins_a
- &mmc0_cd_cfg &mmc0_sck_cfg>;
- bus-width = <8>;
- vmmc-supply = <®_3p3v>;
- status = "okay";
- non-removable;
- };
-
- ssp2: spi@80014000 {
- compatible = "fsl,imx28-mmc";
- pinctrl-names = "default";
- pinctrl-0 = <&mmc2_4bit_pins_b
- &mmc2_cd_cfg &mmc2_sck_cfg_b>;
- bus-width = <4>;
- vmmc-supply = <®_3p3v>;
- status = "okay";
- };
-
- pinctrl@80018000 {
- pinctrl-names = "default";
- pinctrl-0 = <&hog_pins_a>;
-
- hog_pins_a: hog@0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_LCD_D17__GPIO_1_17 /* Revision detection */
- >;
- fsl,drive-strength = <MXS_DRIVE_4mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_DISABLE>;
- };
-
- mac0_phy_reset_pin: mac0-phy-reset@0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_GPMI_ALE__GPIO_0_26 /* PHY Reset */
- >;
- fsl,drive-strength = <MXS_DRIVE_4mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_DISABLE>;
- };
-
- mac0_phy_int_pin: mac0-phy-int@0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_GPMI_D07__GPIO_0_7 /* PHY Interrupt */
- >;
- fsl,drive-strength = <MXS_DRIVE_4mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_DISABLE>;
- };
-
- led_pins: leds@0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_SAIF0_MCLK__GPIO_3_20
- MX28_PAD_SAIF0_LRCLK__GPIO_3_21
- MX28_PAD_AUART0_CTS__GPIO_3_2
- MX28_PAD_I2C0_SCL__GPIO_3_24
- MX28_PAD_I2C0_SDA__GPIO_3_25
- >;
- fsl,drive-strength = <MXS_DRIVE_4mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_DISABLE>;
- };
-
- enocean_button: enocean-button@0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_AUART0_RTS__GPIO_3_3
- >;
- fsl,drive-strength = <MXS_DRIVE_4mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_DISABLE>;
- };
- };
- };
-
- apbx@80040000 {
- lradc@80050000 {
- status = "okay";
- };
-
- auart0: serial@8006a000 {
- pinctrl-names = "default";
- pinctrl-0 = <&auart0_2pins_a>;
- status = "okay";
- };
-
- duart: serial@80074000 {
- pinctrl-names = "default";
- pinctrl-0 = <&duart_pins_a>;
- status = "okay";
- };
-
- usbphy0: usbphy@8007c000 {
- status = "okay";
- };
- };
- };
-
- ahb@80080000 {
- usb0: usb@80080000 {
- status = "okay";
- dr_mode = "peripheral";
- };
-
- mac0: ethernet@800f0000 {
- phy-mode = "rmii";
- pinctrl-names = "default";
- pinctrl-0 = <&mac0_pins_a>, <&mac0_phy_reset_pin>;
- phy-supply = <®_3p3v>;
- phy-reset-gpios = <&gpio0 26 GPIO_ACTIVE_LOW>;
- phy-reset-duration = <25>;
- phy-handle = <ðphy>;
- status = "okay";
-
- mdio {
- #address-cells = <1>;
- #size-cells = <0>;
-
- ethphy: ethernet-phy@0 {
- compatible = "ethernet-phy-ieee802.3-c22";
- reg = <0>;
- pinctrl-names = "default";
- pinctrl-0 = <&mac0_phy_int_pin>;
- interrupt-parent = <&gpio0>;
- interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
- max-speed = <100>;
- };
- };
- };
- };
-
- reg_3p3v: regulator-3p3v {
- compatible = "regulator-fixed";
- regulator-name = "3P3V";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-always-on;
- };
-
leds {
- compatible = "gpio-leds";
- pinctrl-names = "default";
- pinctrl-0 = <&led_pins>;
-
- status-red {
- label = "duckbill:red:status";
- gpios = <&gpio3 21 GPIO_ACTIVE_HIGH>;
- linux,default-trigger = "default-on";
- };
-
- status-green {
- label = "duckbill:green:status";
- gpios = <&gpio3 20 GPIO_ACTIVE_HIGH>;
- linux,default-trigger = "heartbeat";
- };
-
enocean-blue {
label = "duckbill:blue:enocean";
gpios = <&gpio3 24 GPIO_ACTIVE_LOW>;
};
};
};
+
+&i2c0 {
+ status = "disabled";
+};
+
+&led_pins {
+ fsl,pinmux-ids = <
+ MX28_PAD_SAIF0_MCLK__GPIO_3_20
+ MX28_PAD_SAIF0_LRCLK__GPIO_3_21
+ MX28_PAD_AUART0_CTS__GPIO_3_2
+ MX28_PAD_I2C0_SCL__GPIO_3_24
+ MX28_PAD_I2C0_SDA__GPIO_3_25
+ >;
+};
+
+&pinctrl {
+ enocean_button: enocean-button@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_AUART0_RTS__GPIO_3_3
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+};
*/
/dts-v1/;
-#include <dt-bindings/interrupt-controller/irq.h>
-#include <dt-bindings/gpio/gpio.h>
-#include "imx28.dtsi"
+#include "imx28-duckbill-2.dts"
/ {
model = "I2SE Duckbill 2 SPI";
aliases {
ethernet1 = &qca7000;
};
+};
- memory@40000000 {
- device_type = "memory";
- reg = <0x40000000 0x08000000>;
- };
-
- apb@80000000 {
- apbh@80000000 {
- ssp0: spi@80010000 {
- compatible = "fsl,imx28-mmc";
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_8bit_pins_a
- &mmc0_cd_cfg &mmc0_sck_cfg>;
- bus-width = <8>;
- vmmc-supply = <®_3p3v>;
- status = "okay";
- non-removable;
- };
-
- ssp2: spi@80014000 {
- compatible = "fsl,imx28-spi";
- pinctrl-names = "default";
- pinctrl-0 = <&spi2_pins_a>;
- status = "okay";
-
- qca7000: ethernet@0 {
- reg = <0>;
- compatible = "qca,qca7000";
- pinctrl-names = "default";
- pinctrl-0 = <&qca7000_pins>;
- interrupt-parent = <&gpio3>;
- interrupts = <3 IRQ_TYPE_EDGE_RISING>;
- spi-cpha;
- spi-cpol;
- spi-max-frequency = <8000000>;
- };
- };
-
- pinctrl@80018000 {
- pinctrl-names = "default";
- pinctrl-0 = <&hog_pins_a>;
-
- hog_pins_a: hog@0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_LCD_D17__GPIO_1_17 /* Revision detection */
- >;
- fsl,drive-strength = <MXS_DRIVE_4mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_DISABLE>;
- };
-
- mac0_phy_reset_pin: mac0-phy-reset@0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_GPMI_ALE__GPIO_0_26 /* PHY Reset */
- >;
- fsl,drive-strength = <MXS_DRIVE_4mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_DISABLE>;
- };
-
- mac0_phy_int_pin: mac0-phy-int@0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_GPMI_D07__GPIO_0_7 /* PHY Interrupt */
- >;
- fsl,drive-strength = <MXS_DRIVE_4mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_DISABLE>;
- };
-
- led_pins: led@0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_SAIF0_MCLK__GPIO_3_20
- MX28_PAD_SAIF0_LRCLK__GPIO_3_21
- >;
- fsl,drive-strength = <MXS_DRIVE_4mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_DISABLE>;
- };
-
- qca7000_pins: qca7000@0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_AUART0_RTS__GPIO_3_3 /* Interrupt */
- MX28_PAD_LCD_D13__GPIO_1_13 /* QCA7K reset */
- MX28_PAD_LCD_D14__GPIO_1_14 /* GPIO 0 */
- MX28_PAD_LCD_D15__GPIO_1_15 /* GPIO 1 */
- MX28_PAD_LCD_D18__GPIO_1_18 /* GPIO 2 */
- MX28_PAD_LCD_D21__GPIO_1_21 /* GPIO 3 */
- >;
- fsl,drive-strength = <MXS_DRIVE_4mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_DISABLE>;
- };
- };
- };
-
- apbx@80040000 {
- lradc@80050000 {
- status = "okay";
- };
-
- duart: serial@80074000 {
- pinctrl-names = "default";
- pinctrl-0 = <&duart_pins_a>;
- status = "okay";
- };
-
- usbphy0: usbphy@8007c000 {
- status = "okay";
- };
- };
- };
-
- ahb@80080000 {
- usb0: usb@80080000 {
- status = "okay";
- dr_mode = "peripheral";
- };
-
- mac0: ethernet@800f0000 {
- phy-mode = "rmii";
- pinctrl-names = "default";
- pinctrl-0 = <&mac0_pins_a>, <&mac0_phy_reset_pin>;
- phy-supply = <®_3p3v>;
- phy-reset-gpios = <&gpio0 26 GPIO_ACTIVE_LOW>;
- phy-reset-duration = <25>;
- phy-handle = <ðphy>;
- status = "okay";
-
- mdio {
- #address-cells = <1>;
- #size-cells = <0>;
+&auart0 {
+ status = "disabled";
+};
- ethphy: ethernet-phy@0 {
- compatible = "ethernet-phy-ieee802.3-c22";
- reg = <0>;
- pinctrl-names = "default";
- pinctrl-0 = <&mac0_phy_int_pin>;
- interrupt-parent = <&gpio0>;
- interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
- max-speed = <100>;
- };
- };
- };
- };
+&i2c0 {
+ status = "disabled";
+};
- reg_3p3v: regulator-3p3v {
- compatible = "regulator-fixed";
- regulator-name = "3P3V";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-always-on;
+&pinctrl {
+ qca7000_pins: qca7000@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_AUART0_RTS__GPIO_3_3 /* Interrupt */
+ MX28_PAD_LCD_D13__GPIO_1_13 /* QCA7K reset */
+ MX28_PAD_LCD_D14__GPIO_1_14 /* GPIO 0 */
+ MX28_PAD_LCD_D15__GPIO_1_15 /* GPIO 1 */
+ MX28_PAD_LCD_D18__GPIO_1_18 /* GPIO 2 */
+ MX28_PAD_LCD_D21__GPIO_1_21 /* GPIO 3 */
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
+};
- leds {
- compatible = "gpio-leds";
+&ssp2 {
+ compatible = "fsl,imx28-spi";
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi2_pins_a>;
+ /delete-property/ bus-width;
+ /delete-property/ vmmc-supply;
+ status = "okay";
+
+ qca7000: ethernet@0 {
+ reg = <0>;
+ compatible = "qca,qca7000";
pinctrl-names = "default";
- pinctrl-0 = <&led_pins>;
-
- status-red {
- label = "duckbill:red:status";
- gpios = <&gpio3 21 GPIO_ACTIVE_HIGH>;
- linux,default-trigger = "default-on";
- };
-
- status-green {
- label = "duckbill:green:status";
- gpios = <&gpio3 20 GPIO_ACTIVE_HIGH>;
- linux,default-trigger = "heartbeat";
- };
+ pinctrl-0 = <&qca7000_pins>;
+ interrupt-parent = <&gpio3>;
+ interrupts = <3 IRQ_TYPE_EDGE_RISING>;
+ spi-cpha;
+ spi-cpol;
+ spi-max-frequency = <8000000>;
};
};
projects / platform / kernel / linux-starfive.git / commitdiff