overlays/rpi-display: Add support for DRM driver

Add a "drm" parameter that enables use of the drm/mi0283qt driver instead
of fbtft/fb_ili9341. Also add a "backlight-pwm" parameter that can be used
with the "drm" parameter.

Signed-off-by: Noralf Trønnes <noralf@tronnes.org>

diff --git a/arch/arm/boot/dts/overlays/README b/arch/arm/boot/dts/overlays/README
index d7082ec..4bc780a 100644 (file)
--- a/arch/arm/boot/dts/overlays/README
+++ b/arch/arm/boot/dts/overlays/README
@@ -2913,14 +2913,36 @@ Params: <None>
 
 Name:   rpi-display
 Info:   RPi-Display - 2.8" Touch Display by Watterott
+        Linux has 2 drivers that support this display and this overlay supports
+        both.
+
+        Examples:
+          fbtft/fb_ili9341: dtoverlay=rpi-display
+          drm/mi0283qt: dtoverlay=rpi-display,drm,backlight-pwm,rotate=180
+
+        Some notable differences with the DRM driver compared to fbtft:
+        - The display is turned on when it's first used and not on driver load
+          as with fbtft. So if nothing uses the display it stays off.
+        - Can run with a higher SPI clock increasing framerate. This is possible
+          since the driver avoids messing up the controller configuration due to
+          transmission errors by running config commands at 10MHz and only pixel
+          data at full speed (occasional pixel glitch might occur).
+        - PWM backlight is supported.
+
 Load:   dtoverlay=rpi-display,<param>=<val>
 Params: speed                   Display SPI bus speed
         rotate                  Display rotation {0,90,180,270}
-        fps                     Delay between frame updates
-        debug                   Debug output level {0-7}
+        fps                     Delay between frame updates (fbtft only)
+        debug                   Debug output level {0-7} (fbtft only)
         xohms                   Touchpanel sensitivity (X-plate resistance)
         swapxy                  Swap x and y axis
         backlight               Change backlight GPIO pin {e.g. 12, 18}
+                                (fbtft only)
+        drm                     Use DRM/KMS driver mi0283qt instead of fbtft.
+                                Set the SPI clock to 70MHz.
+                                This has to be the first parameter.
+        backlight-pwm           Use pwm for backlight (drm only). NB: Disables
+                                audio headphone output as that also uses PWM.
 
 
 Name:   rpi-ft5406

diff --git a/arch/arm/boot/dts/overlays/rpi-display-overlay.dts b/arch/arm/boot/dts/overlays/rpi-display-overlay.dts
index de87432..789644b 100644 (file)
--- a/arch/arm/boot/dts/overlays/rpi-display-overlay.dts
+++ b/arch/arm/boot/dts/overlays/rpi-display-overlay.dts
@@ -78,14 +78,73 @@
                        };
                };
        };
+
+       fragment@10 {
+               target = <&rpidisplay>;
+               __dormant__  {
+                       backlight = <&backlight_gpio>;
+               };
+       };
+
+       fragment@11 {
+               target-path = "/";
+               __dormant__  {
+                       backlight_gpio: backlight_gpio {
+                               compatible = "gpio-backlight";
+                               gpios = <&gpio 18 0>; /* GPIO_ACTIVE_HIGH */
+                       };
+               };
+       };
+
+       fragment@20 {
+               target = <&rpidisplay>;
+               __dormant__  {
+                       backlight = <&backlight_pwm>;
+               };
+       };
+
+       fragment@21 {
+               target-path = "/";
+               __dormant__  {
+                       backlight_pwm: backlight_pwm {
+                               compatible = "pwm-backlight";
+                               brightness-levels = <0 6 8 12 16 24 32 40 48 64 96 128 160 192 224 255>;
+                               default-brightness-level = <16>;
+                               pwms = <&pwm 0 200000>;
+                       };
+               };
+       };
+
+       fragment@22 {
+               target = <&pwm>;
+               __dormant__ {
+                       assigned-clock-rates = <1000000>;
+                       status = "okay";
+               };
+       };
+
+       fragment@23 {
+               target = <&audio>;
+               __dormant__  {
+                   brcm,disable-headphones;
+               };
+       };
+
        __overrides__ {
                speed =     <&rpidisplay>,"spi-max-frequency:0";
-               rotate =    <&rpidisplay>,"rotate:0";
+               rotate =    <&rpidisplay>,"rotate:0", /* fbtft */
+                           <&rpidisplay>,"rotation:0"; /* drm */
                fps =       <&rpidisplay>,"fps:0";
                debug =     <&rpidisplay>,"debug:0";
                xohms =     <&rpidisplay_ts>,"ti,x-plate-ohms;0";
                swapxy =    <&rpidisplay_ts>,"ti,swap-xy?";
                backlight = <&rpidisplay>,"led-gpios:4",
                            <&rpi_display_pins>,"brcm,pins:0";
+               drm =       <&rpidisplay>, "compatible=multi-inno,mi0283qt",
+                           <&rpidisplay>, "spi-max-frequency:0=70000000",
+                           <&rpidisplay>, "reset-gpios:8=0", /* GPIO_ACTIVE_HIGH */
+                           <0>, "+10+11";
+               backlight-pwm = <0>, "-10-11+20+21+22+23",
+                               <&rpi_display_pins>, "brcm,function:0=2"; /* Alt5 */
        };
 };