mtd: m25p80: Make fast read configurable via DT
authorMarek Vasut <marex@denx.de>
Mon, 24 Sep 2012 01:39:39 +0000 (03:39 +0200)
committerArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Thu, 15 Nov 2012 13:37:46 +0000 (15:37 +0200)
Add DT property "m25p,fast-read" that signalises the particular
chip supports "fast read" opcode.

Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Documentation/devicetree/bindings/mtd/m25p80.txt [new file with mode: 0644]
drivers/mtd/devices/m25p80.c

diff --git a/Documentation/devicetree/bindings/mtd/m25p80.txt b/Documentation/devicetree/bindings/mtd/m25p80.txt
new file mode 100644 (file)
index 0000000..6d3d576
--- /dev/null
@@ -0,0 +1,29 @@
+* MTD SPI driver for ST M25Pxx (and similar) serial flash chips
+
+Required properties:
+- #address-cells, #size-cells : Must be present if the device has sub-nodes
+  representing partitions.
+- compatible : Should be the manufacturer and the name of the chip. Bear in mind
+               the DT binding is not Linux-only, but in case of Linux, see the
+               "m25p_ids" table in drivers/mtd/devices/m25p80.c for the list of
+               supported chips.
+- reg : Chip-Select number
+- spi-max-frequency : Maximum frequency of the SPI bus the chip can operate at
+
+Optional properties:
+- m25p,fast-read : Use the "fast read" opcode to read data from the chip instead
+                   of the usual "read" opcode. This opcode is not supported by
+                   all chips and support for it can not be detected at runtime.
+                   Refer to your chips' datasheet to check if this is supported
+                   by your chip.
+
+Example:
+
+       flash: m25p80@0 {
+               #address-cells = <1>;
+               #size-cells = <1>;
+               compatible = "spansion,m25p80";
+               reg = <0>;
+               spi-max-frequency = <40000000>;
+               m25p,fast-read;
+       };
index 03838ba..82f9774 100644 (file)
 #define        MAX_READY_WAIT_JIFFIES  (40 * HZ)       /* M25P16 specs 40s max chip erase */
 #define        MAX_CMD_SIZE            5
 
-#ifdef CONFIG_M25PXX_USE_FAST_READ
-#define OPCODE_READ    OPCODE_FAST_READ
-#define FAST_READ_DUMMY_BYTE 1
-#else
-#define OPCODE_READ    OPCODE_NORM_READ
-#define FAST_READ_DUMMY_BYTE 0
-#endif
-
 #define JEDEC_MFR(_jedec_id)   ((_jedec_id) >> 16)
 
 /****************************************************************************/
@@ -93,6 +85,7 @@ struct m25p {
        u16                     addr_width;
        u8                      erase_opcode;
        u8                      *command;
+       bool                    fast_read;
 };
 
 static inline struct m25p *mtd_to_m25p(struct mtd_info *mtd)
@@ -342,6 +335,7 @@ static int m25p80_read(struct mtd_info *mtd, loff_t from, size_t len,
        struct m25p *flash = mtd_to_m25p(mtd);
        struct spi_transfer t[2];
        struct spi_message m;
+       uint8_t opcode;
 
        pr_debug("%s: %s from 0x%08x, len %zd\n", dev_name(&flash->spi->dev),
                        __func__, (u32)from, len);
@@ -354,7 +348,7 @@ static int m25p80_read(struct mtd_info *mtd, loff_t from, size_t len,
         * Should add 1 byte DUMMY_BYTE.
         */
        t[0].tx_buf = flash->command;
-       t[0].len = m25p_cmdsz(flash) + FAST_READ_DUMMY_BYTE;
+       t[0].len = m25p_cmdsz(flash) + (flash->fast_read ? 1 : 0);
        spi_message_add_tail(&t[0], &m);
 
        t[1].rx_buf = buf;
@@ -376,12 +370,14 @@ static int m25p80_read(struct mtd_info *mtd, loff_t from, size_t len,
         */
 
        /* Set up the write data buffer. */
-       flash->command[0] = OPCODE_READ;
+       opcode = flash->fast_read ? OPCODE_FAST_READ : OPCODE_NORM_READ;
+       flash->command[0] = opcode;
        m25p_addr2cmd(flash, from, flash->command);
 
        spi_sync(flash->spi, &m);
 
-       *retlen = m.actual_length - m25p_cmdsz(flash) - FAST_READ_DUMMY_BYTE;
+       *retlen = m.actual_length - m25p_cmdsz(flash) -
+                       (flash->fast_read ? 1 : 0);
 
        mutex_unlock(&flash->lock);
 
@@ -809,9 +805,10 @@ static int __devinit m25p_probe(struct spi_device *spi)
        struct flash_info               *info;
        unsigned                        i;
        struct mtd_part_parser_data     ppdata;
+       struct device_node __maybe_unused *np = spi->dev.of_node;
 
 #ifdef CONFIG_MTD_OF_PARTS
-       if (!of_device_is_available(spi->dev.of_node))
+       if (!of_device_is_available(np))
                return -ENODEV;
 #endif
 
@@ -863,7 +860,8 @@ static int __devinit m25p_probe(struct spi_device *spi)
        flash = kzalloc(sizeof *flash, GFP_KERNEL);
        if (!flash)
                return -ENOMEM;
-       flash->command = kmalloc(MAX_CMD_SIZE + FAST_READ_DUMMY_BYTE, GFP_KERNEL);
+       flash->command = kmalloc(MAX_CMD_SIZE + (flash->fast_read ? 1 : 0),
+                                       GFP_KERNEL);
        if (!flash->command) {
                kfree(flash);
                return -ENOMEM;
@@ -920,6 +918,16 @@ static int __devinit m25p_probe(struct spi_device *spi)
        flash->page_size = info->page_size;
        flash->mtd.writebufsize = flash->page_size;
 
+       flash->fast_read = false;
+#ifdef CONFIG_OF
+       if (np && of_property_read_bool(np, "m25p,fast-read"))
+               flash->fast_read = true;
+#endif
+
+#ifdef CONFIG_M25PXX_USE_FAST_READ
+       flash->fast_read = true;
+#endif
+
        if (info->addr_width)
                flash->addr_width = info->addr_width;
        else {