+++ /dev/null
-* Marvell EBU GPIO controller
-
-Required properties:
-
-- compatible : Should be "marvell,orion-gpio", "marvell,mv78200-gpio",
- "marvell,armadaxp-gpio" or "marvell,armada-8k-gpio".
-
- "marvell,orion-gpio" should be used for Orion, Kirkwood, Dove,
- Discovery (except MV78200) and Armada 370. "marvell,mv78200-gpio"
- should be used for the Discovery MV78200.
-
- "marvel,armadaxp-gpio" should be used for all Armada XP SoCs
- (MV78230, MV78260, MV78460).
-
- "marvell,armada-8k-gpio" should be used for the Armada 7K and 8K
- SoCs (either from AP or CP), see
- Documentation/devicetree/bindings/arm/marvell/ap80x-system-controller.txt
- for specific details about the offset property.
-
-- reg: Address and length of the register set for the device. Only one
- entry is expected, except for the "marvell,armadaxp-gpio" variant
- for which two entries are expected: one for the general registers,
- one for the per-cpu registers. Not used for marvell,armada-8k-gpio.
-
-- interrupts: The list of interrupts that are used for all the pins
- managed by this GPIO bank. There can be more than one interrupt
- (example: 1 interrupt per 8 pins on Armada XP, which means 4
- interrupts per bank of 32 GPIOs).
-
-- interrupt-controller: identifies the node as an interrupt controller
-
-- #interrupt-cells: specifies the number of cells needed to encode an
- interrupt source. Should be two.
- The first cell is the GPIO number.
- The second cell is used to specify flags:
- bits[3:0] trigger type and level flags:
- 1 = low-to-high edge triggered.
- 2 = high-to-low edge triggered.
- 4 = active high level-sensitive.
- 8 = active low level-sensitive.
-
-- gpio-controller: marks the device node as a gpio controller
-
-- ngpios: number of GPIOs this controller has
-
-- #gpio-cells: Should be two. The first cell is the pin number. The
- second cell is reserved for flags, unused at the moment.
-
-Optional properties:
-
-In order to use the GPIO lines in PWM mode, some additional optional
-properties are required.
-
-- compatible: Must contain "marvell,armada-370-gpio"
-
-- reg: an additional register set is needed, for the GPIO Blink
- Counter on/off registers.
-
-- reg-names: Must contain an entry "pwm" corresponding to the
- additional register range needed for PWM operation.
-
-- #pwm-cells: Should be two. The first cell is the GPIO line number. The
- second cell is the period in nanoseconds.
-
-- clocks: Must be a phandle to the clock for the GPIO controller.
-
-Example:
-
- gpio0: gpio@d0018100 {
- compatible = "marvell,armadaxp-gpio";
- reg = <0xd0018100 0x40>,
- <0xd0018800 0x30>;
- ngpios = <32>;
- gpio-controller;
- #gpio-cells = <2>;
- interrupt-controller;
- #interrupt-cells = <2>;
- interrupts = <16>, <17>, <18>, <19>;
- };
-
- gpio1: gpio@18140 {
- compatible = "marvell,armada-370-gpio";
- reg = <0x18140 0x40>, <0x181c8 0x08>;
- reg-names = "gpio", "pwm";
- ngpios = <17>;
- gpio-controller;
- #gpio-cells = <2>;
- #pwm-cells = <2>;
- interrupt-controller;
- #interrupt-cells = <2>;
- interrupts = <87>, <88>, <89>;
- clocks = <&coreclk 0>;
- };
--- /dev/null
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/gpio/gpio-mvebu.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Marvell EBU GPIO controller
+
+maintainers:
+ - Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
+ - Andrew Lunn <andrew@lunn.ch>
+
+properties:
+ compatible:
+ oneOf:
+ - enum:
+ - marvell,armada-8k-gpio
+ - marvell,orion-gpio
+
+ - items:
+ - enum:
+ - marvell,mv78200-gpio
+ - marvell,armada-370-gpio
+ - marvell,armadaxp-gpio
+ - const: marvell,orion-gpio
+
+ reg:
+ description: |
+ Address and length of the register set for the device. Not used for
+ marvell,armada-8k-gpio.
+
+ For the "marvell,armadaxp-gpio" variant a second entry is expected for
+ the per-cpu registers. For other variants second entry can be provided,
+ for the PWM function using the GPIO Blink Counter on/off registers.
+ minItems: 1
+ maxItems: 2
+
+ reg-names:
+ items:
+ - const: gpio
+ - const: pwm
+ minItems: 1
+
+ interrupts:
+ description: |
+ The list of interrupts that are used for all the pins managed by this
+ GPIO bank. There can be more than one interrupt (example: 1 interrupt
+ per 8 pins on Armada XP, which means 4 interrupts per bank of 32
+ GPIOs).
+ minItems: 1
+ maxItems: 4
+
+ interrupt-controller: true
+
+ "#interrupt-cells":
+ const: 2
+
+ gpio-controller: true
+
+ ngpios:
+ minimum: 1
+ maximum: 32
+
+ "#gpio-cells":
+ const: 2
+
+ "#pwm-cells":
+ description:
+ The first cell is the GPIO line number. The second cell is the period
+ in nanoseconds.
+ const: 2
+
+ clocks:
+ description:
+ Clock(s) used for PWM function.
+ items:
+ - description: Core clock
+ - description: AXI bus clock
+ minItems: 1
+
+ clock-names:
+ items:
+ - const: core
+ - const: axi
+ minItems: 1
+
+required:
+ - compatible
+ - gpio-controller
+ - ngpios
+ - "#gpio-cells"
+
+allOf:
+ - if:
+ properties:
+ compatible:
+ contains:
+ const: marvell,armada-8k-gpio
+ then:
+ required:
+ - offset
+ else:
+ required:
+ - reg
+
+ - if:
+ properties:
+ compatible:
+ contains:
+ const: marvell,armadaxp-gpio
+ then:
+ properties:
+ reg:
+ minItems: 2
+ reg-names:
+ minItems: 2
+
+unevaluatedProperties: true
+
+examples:
+ - |
+ gpio@d0018100 {
+ compatible = "marvell,armadaxp-gpio", "marvell,orion-gpio";
+ reg = <0xd0018100 0x40>, <0xd0018800 0x30>;
+ ngpios = <32>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ interrupts = <16>, <17>, <18>, <19>;
+ };
+
+ - |
+ gpio@18140 {
+ compatible = "marvell,armada-370-gpio", "marvell,orion-gpio";
+ reg = <0x18140 0x40>, <0x181c8 0x08>;
+ reg-names = "gpio", "pwm";
+ ngpios = <17>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ #pwm-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ interrupts = <87>, <88>, <89>;
+ clocks = <&coreclk 0>;
+ };
projects / platform / kernel / linux-rpi.git / commitdiff