-------------
=============== ============================================
-temp1_input Measured temperature in millidegrees Celcius
+temp1_input Measured temperature in millidegrees Celsius
humidity1_input Measured humidity in %H
update_interval The minimum interval for polling the sensor,
in milliseconds. Writable. Must be at
Description:
------------
This driver implements support for ASPEED AST2400/2500 PWM and Fan Tacho
-controller. The PWM controller supports upto 8 PWM outputs. The Fan tacho
+controller. The PWM controller supports up to 8 PWM outputs. The Fan tacho
controller supports up to 16 tachometer inputs.
The driver provides the following sensor accesses in sysfs:
interface of the HXi and RMi series.
These power supplies provide access to a micro-controller with 2 attached
temperature sensors, 1 fan rpm sensor, 4 sensors for volt levels, 4 sensors for
-power usage and 4 sensors for current levels and addtional non-sensor information
+power usage and 4 sensors for current levels and additional non-sensor information
like uptimes.
Sysfs entries
Temperatures are measured with 12-bit or 10-bit resolution and are scaled
either internally or by the driver depending on the GSC version and firmware.
-The values returned by the driver reflect millidegree Celcius:
+The values returned by the driver reflect millidegree Celsius:
tempX_input Measured temperature.
tempX_label Name of temperature input.
------------------
The GSC features 1 PWM output that operates in automatic mode where the
-PWM value will be scalled depending on 6 temperature boundaries.
-The tempeature boundaries are read-write and in millidegree Celcius and the
+PWM value will be scaled depending on 6 temperature boundaries.
+The tempeature boundaries are read-write and in millidegree Celsius and the
read-only PWM values range from 0 (off) to 255 (full speed).
Fan speed will be set to minimum (off) when the temperature sensor reads
less than pwm1_auto_point1_temp and maximum when the temperature sensor
hwmon_device_register_with_groups registers a hardware monitoring device.
The first parameter of this function is a pointer to the parent device.
The name parameter is a pointer to the hwmon device name. The registration
-function wil create a name sysfs attribute pointing to this name.
+function will create a name sysfs attribute pointing to this name.
The drvdata parameter is the pointer to the local driver data.
hwmon_device_register_with_groups will attach this pointer to the newly
allocated hwmon device. The pointer can be retrieved by the driver using
The header file linux/hwmon-sysfs.h provides a number of useful macros to
declare and use hardware monitoring sysfs attributes.
-In many cases, you can use the exsting define DEVICE_ATTR or its variants
+In many cases, you can use the existing define DEVICE_ATTR or its variants
DEVICE_ATTR_{RW,RO,WO} to declare such attributes. This is feasible if an
attribute has no additional context. However, in many cases there will be
additional information such as a sensor index which will need to be passed
- On LTC3883, temp1 reports an external temperature,
and temp2 reports the chip temperature.
-temp[N]_min Mimimum temperature.
+temp[N]_min Minimum temperature.
LTC2972, LTC2974, LCT2977, LTM2980, LTC2978,
LTC2979, and LTM2987 only.
This driver implements support for several MAX6697 compatible temperature sensor
chips. The chips support one local temperature sensor plus four, six, or seven
remote temperature sensors. Remote temperature sensors are diode-connected
-thermal transitors, except for MAX6698 which supports three diode-connected
+thermal transistors, except for MAX6698 which supports three diode-connected
thermal transistors plus three thermistors in addition to the local temperature
sensor.
Prefix: 'menf21bmc_hwmon'
- Adresses scanned: -
+ Addresses scanned: -
Author: Andreas Werner <andreas.werner@men.de>
int (*read_word_data)(struct i2c_client *client, int page, int phase,
int reg);
-Read word from page <page>, phase <pase>, register <reg>. If the chip does not
+Read word from page <page>, phase <phase>, register <reg>. If the chip does not
support multiple phases, the phase parameter can be ignored. If the chip
supports multiple phases, a phase value of 0xff indicates all phases.
-------------
=============== ============================================
-temp1_input Measured temperature in millidegrees Celcius
+temp1_input Measured temperature in millidegrees Celsius
humidity1_input Measured humidity in %H
update_interval The minimum interval for polling the sensor,
in milliseconds. Writable. Must be at least
in10_crit_alarm AIN2 critical alarm
temp1_input Chip temperature
-temp1_min Mimimum chip temperature
+temp1_min Minimum chip temperature
temp1_max Maximum chip temperature
temp1_crit Critical chip temperature
temp1_crit_alarm Temperature critical alarm
in 50mV steps. This means that the absolute values of the limits will change
when the commanded output voltage changes. Also, care should be taken when
writing to those limits since in the worst case the commanded output voltage
-could change at the same time as the limit is written to, wich will lead to
+could change at the same time as the limit is written to, which will lead to
unpredictable results.
reference & prototyping system for ARM Ltd. processors. It can be set up
from a wide range of boards, each of them containing (apart of the main
chip/FPGA) a number of microcontrollers responsible for platform
-configuration and control. Theses microcontrollers can also monitor the
+configuration and control. These microcontrollers can also monitor the
board and its environment by a number of internal and external sensors,
providing information about power lines voltages and currents, board
temperature and power usage. Some of them also calculate consumed energy
Voltage sensors (also known as IN sensors) report their values in volts.
An alarm is triggered if the voltage has crossed a programmable minimum
-or maximum limit. Voltages are internally scalled, so each voltage channel
+or maximum limit. Voltages are internally scaled, so each voltage channel
has a different resolution and range.
If an alarm triggers, it will remain triggered until the hardware register
projects / platform / kernel / linux-starfive.git / commitdiff