&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_a>;
+ pinctrl-0 = <&uart0_pb_pins>;
status = "okay";
};
leds {
compatible = "gpio-leds";
- pinctrl-names = "default";
- pinctrl-0 = <&led_pins_bpi_m1p>;
green {
label = "bananapi-m1-plus:green:usr";
mmc3_pwrseq: mmc3_pwrseq {
compatible = "mmc-pwrseq-simple";
- pinctrl-names = "default";
- pinctrl-0 = <&mmc3_pwrseq_pin_bpi_m1p>;
reset-gpios = <&pio 7 22 GPIO_ACTIVE_LOW>; /* PH22 WL-PMU-EN */
};
reg_gmac_3v3: gmac-3v3 {
compatible = "regulator-fixed";
- pinctrl-names = "default";
- pinctrl-0 = <&gmac_power_pin_bpi_m1p>;
regulator-name = "gmac-3v3";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
&gmac {
pinctrl-names = "default";
- pinctrl-0 = <&gmac_pins_rgmii_a>;
+ pinctrl-0 = <&gmac_rgmii_pins>;
phy = <&phy1>;
phy-mode = "rgmii";
phy-supply = <®_gmac_3v3>;
};
&i2c0 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins_a>;
status = "okay";
axp209: pmic@34 {
&ir0 {
pinctrl-names = "default";
- pinctrl-0 = <&ir0_rx_pins_a>;
+ pinctrl-0 = <&ir0_rx_pin>;
status = "okay";
};
&mmc0 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_bpi_m1p>;
vmmc-supply = <®_vcc3v3>;
bus-width = <4>;
cd-gpios = <&pio 7 10 GPIO_ACTIVE_LOW>; /* PH10 */
&mmc3 {
#address-cells = <1>;
#size-cells = <0>;
- pinctrl-names = "default";
- pinctrl-0 = <&mmc3_pins_a>;
vmmc-supply = <®_vcc3v3>;
mmc-pwrseq = <&mmc3_pwrseq>;
bus-width = <4>;
};
};
-&mmc3_pins_a {
- /* AP6210 requires pull-up */
- bias-pull-up;
-};
-
&ohci0 {
status = "okay";
};
status = "okay";
};
-&pio {
- gmac_power_pin_bpi_m1p: gmac_power_pin@0 {
- pins = "PH23";
- function = "gpio_out";
- };
-
- led_pins_bpi_m1p: led_pins@0 {
- pins = "PH24", "PH25";
- function = "gpio_out";
- };
-
- mmc0_cd_pin_bpi_m1p: mmc0_cd_pin@0 {
- pins = "PH10";
- function = "gpio_in";
- bias-pull-up;
- };
-
- mmc3_pwrseq_pin_bpi_m1p: mmc3_pwrseq_pin@0 {
- pins = "PH22";
- function = "gpio_out";
- };
-};
-
®_dcdc2 {
regulator-always-on;
regulator-min-microvolt = <1000000>;
&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_a>;
+ pinctrl-0 = <&uart0_pb_pins>;
status = "okay";
};
leds {
compatible = "gpio-leds";
- pinctrl-names = "default";
- pinctrl-0 = <&led_pins_bananapi>;
green {
label = "bananapi:green:usr";
reg_gmac_3v3: gmac-3v3 {
compatible = "regulator-fixed";
- pinctrl-names = "default";
- pinctrl-0 = <&gmac_power_pin_bananapi>;
regulator-name = "gmac-3v3";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
&gmac {
pinctrl-names = "default";
- pinctrl-0 = <&gmac_pins_rgmii_a>;
+ pinctrl-0 = <&gmac_rgmii_pins>;
phy = <&phy1>;
phy-mode = "rgmii";
phy-supply = <®_gmac_3v3>;
};
&i2c0 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins_a>;
status = "okay";
axp209: pmic@34 {
};
&i2c2 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c2_pins_a>;
status = "okay";
};
&ir0 {
pinctrl-names = "default";
- pinctrl-0 = <&ir0_rx_pins_a>;
+ pinctrl-0 = <&ir0_rx_pin>;
status = "okay";
};
&mmc0 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_bananapi>;
vmmc-supply = <®_vcc3v3>;
bus-width = <4>;
cd-gpios = <&pio 7 10 GPIO_ACTIVE_LOW>; /* PH10 */
};
&pio {
+ vcc-pa-supply = <®_vcc3v3>;
+ vcc-pc-supply = <®_vcc3v3>;
+ vcc-pe-supply = <®_vcc3v3>;
+ vcc-pf-supply = <®_vcc3v3>;
+ vcc-pg-supply = <®_vcc3v3>;
gpio-line-names =
/* PA */
"ERXD3", "ERXD2", "ERXD1", "ERXD0", "ETXD3",
"IO-6", "IO-3", "IO-2", "IO-0", "", "", "", "",
"", "", "", "", "", "", "", "";
- usb0_id_detect_pin: usb0_id_detect_pin@0 {
+ usb0_id_detect_pin: usb0-id-detect-pin {
pins = "PH4";
function = "gpio_in";
bias-pull-up;
};
-
- mmc0_cd_pin_bananapi: mmc0_cd_pin@0 {
- pins = "PH10";
- function = "gpio_in";
- bias-pull-up;
- };
-
- gmac_power_pin_bananapi: gmac_power_pin@0 {
- pins = "PH23";
- function = "gpio_out";
- };
-
- led_pins_bananapi: led_pins@0 {
- pins = "PH24";
- function = "gpio_out";
- };
};
#include "axp209.dtsi"
&spi0 {
pinctrl-names = "default";
- pinctrl-0 = <&spi0_pins_a>,
- <&spi0_cs0_pins_a>,
- <&spi0_cs1_pins_a>;
+ pinctrl-0 = <&spi0_pi_pins>,
+ <&spi0_cs0_pi_pin>,
+ <&spi0_cs1_pi_pin>;
status = "okay";
};
&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_a>;
+ pinctrl-0 = <&uart0_pb_pins>;
status = "okay";
};
&uart3 {
pinctrl-names = "default";
- pinctrl-0 = <&uart3_pins_b>;
+ pinctrl-0 = <&uart3_ph_pins>;
status = "okay";
};
&uart7 {
pinctrl-names = "default";
- pinctrl-0 = <&uart7_pins_a>;
+ pinctrl-0 = <&uart7_pi_pins>;
status = "okay";
};
leds {
compatible = "gpio-leds";
- pinctrl-names = "default";
- pinctrl-0 = <&led_pins_bananapro>;
blue {
label = "bananapro:blue:usr";
wifi_pwrseq: wifi-pwrseq {
compatible = "mmc-pwrseq-simple";
- pinctrl-names = "default";
- pinctrl-0 = <&vmmc3_pin_bananapro>;
reset-gpios = <&pio 7 22 GPIO_ACTIVE_LOW>;
};
reg_gmac_3v3: gmac-3v3 {
compatible = "regulator-fixed";
- pinctrl-names = "default";
- pinctrl-0 = <&gmac_power_pin_bananapro>;
regulator-name = "gmac-3v3";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
&gmac {
pinctrl-names = "default";
- pinctrl-0 = <&gmac_pins_rgmii_a>;
+ pinctrl-0 = <&gmac_rgmii_pins>;
phy = <&phy1>;
phy-mode = "rgmii";
phy-supply = <®_gmac_3v3>;
};
&i2c0 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins_a>;
status = "okay";
axp209: pmic@34 {
};
&i2c2 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c2_pins_a>;
status = "okay";
};
&ir0 {
pinctrl-names = "default";
- pinctrl-0 = <&ir0_rx_pins_a>;
+ pinctrl-0 = <&ir0_rx_pin>;
status = "okay";
};
&mmc0 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_bananapro>;
vmmc-supply = <®_vcc3v3>;
bus-width = <4>;
cd-gpios = <&pio 7 10 GPIO_ACTIVE_LOW>; /* PH10 */
};
&mmc3 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc3_pins_a>;
vmmc-supply = <®_vcc3v3>;
mmc-pwrseq = <&wifi_pwrseq>;
bus-width = <4>;
status = "okay";
};
-&pio {
- gmac_power_pin_bananapro: gmac_power_pin@0 {
- pins = "PH23";
- function = "gpio_out";
- };
-
- led_pins_bananapro: led_pins@0 {
- pins = "PH24", "PG2";
- function = "gpio_out";
- };
-
- mmc0_cd_pin_bananapro: mmc0_cd_pin@0 {
- pins = "PH10";
- function = "gpio_in";
- bias-pull-up;
- };
-
- usb1_vbus_pin_bananapro: usb1_vbus_pin@0 {
- pins = "PH0";
- function = "gpio_out";
- };
-
- usb2_vbus_pin_bananapro: usb2_vbus_pin@0 {
- pins = "PH1";
- function = "gpio_out";
- };
-
- vmmc3_pin_bananapro: vmmc3_pin@0 {
- pins = "PH22";
- function = "gpio_out";
- };
-};
-
®_usb1_vbus {
- pinctrl-0 = <&usb1_vbus_pin_bananapro>;
gpio = <&pio 7 0 GPIO_ACTIVE_HIGH>; /* PH0 */
status = "okay";
};
®_usb2_vbus {
- pinctrl-0 = <&usb2_vbus_pin_bananapro>;
gpio = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
status = "okay";
};
&spi0 {
pinctrl-names = "default";
- pinctrl-0 = <&spi0_pins_a>,
- <&spi0_cs0_pins_a>,
- <&spi0_cs1_pins_a>;
+ pinctrl-0 = <&spi0_pi_pins>,
+ <&spi0_cs0_pi_pin>,
+ <&spi0_cs1_pi_pin>;
status = "okay";
};
&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_a>;
+ pinctrl-0 = <&uart0_pb_pins>;
status = "okay";
};
&uart4 {
pinctrl-names = "default";
- pinctrl-0 = <&uart4_pins_b>;
+ pinctrl-0 = <&uart4_ph_pins>;
status = "okay";
};
&uart7 {
pinctrl-names = "default";
- pinctrl-0 = <&uart7_pins_a>;
+ pinctrl-0 = <&uart7_pi_pins>;
status = "okay";
};
leds {
compatible = "gpio-leds";
- pinctrl-names = "default";
- pinctrl-0 = <&led_pins_cubieboard2>;
blue {
label = "cubieboard2:blue:usr";
&gmac {
pinctrl-names = "default";
- pinctrl-0 = <&gmac_pins_mii_a>;
+ pinctrl-0 = <&gmac_mii_pins>;
phy = <&phy1>;
phy-mode = "mii";
status = "okay";
};
&i2c0 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins_a>;
status = "okay";
axp209: pmic@34 {
};
&i2c1 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c1_pins_a>;
status = "okay";
};
&ir0 {
pinctrl-names = "default";
- pinctrl-0 = <&ir0_rx_pins_a>;
+ pinctrl-0 = <&ir0_rx_pin>;
status = "okay";
};
&mmc0 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>;
vmmc-supply = <®_vcc3v3>;
bus-width = <4>;
cd-gpios = <&pio 7 1 GPIO_ACTIVE_LOW>; /* PH1 */
};
&pio {
- led_pins_cubieboard2: led_pins@0 {
- pins = "PH20", "PH21";
- function = "gpio_out";
- };
-
- usb0_id_detect_pin: usb0_id_detect_pin@0 {
+ usb0_id_detect_pin: usb0-id-detect-pin {
pins = "PH4";
function = "gpio_in";
bias-pull-up;
&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_a>;
+ pinctrl-0 = <&uart0_pb_pins>;
status = "okay";
};
leds {
compatible = "gpio-leds";
- pinctrl-names = "default";
- pinctrl-0 = <&led_pins_cubietruck>;
blue {
label = "cubietruck:blue:usr";
mmc3_pwrseq: mmc3_pwrseq {
compatible = "mmc-pwrseq-simple";
- pinctrl-names = "default";
- pinctrl-0 = <&mmc3_pwrseq_pin_cubietruck>;
reset-gpios = <&pio 7 9 GPIO_ACTIVE_LOW>; /* PH9 WIFI_EN */
+ clocks = <&ccu CLK_OUT_A>;
+ clock-names = "ext_clock";
};
sound {
&gmac {
pinctrl-names = "default";
- pinctrl-0 = <&gmac_pins_rgmii_a>;
+ pinctrl-0 = <&gmac_rgmii_pins>;
phy = <&phy1>;
phy-mode = "rgmii";
status = "okay";
};
&i2c0 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins_a>;
status = "okay";
axp209: pmic@34 {
&i2c1 {
pinctrl-names = "default";
- pinctrl-0 = <&i2c1_pins_a>;
status = "okay";
};
&i2c2 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c2_pins_a>;
status = "okay";
};
&ir0 {
pinctrl-names = "default";
- pinctrl-0 = <&ir0_rx_pins_a>;
+ pinctrl-0 = <&ir0_rx_pin>;
status = "okay";
};
&mmc0 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>;
vmmc-supply = <®_vcc3v3>;
bus-width = <4>;
cd-gpios = <&pio 7 1 GPIO_ACTIVE_LOW>; /* PH1 */
};
&mmc3 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc3_pins_a>;
vmmc-supply = <®_vcc3v3>;
mmc-pwrseq = <&mmc3_pwrseq>;
bus-width = <4>;
};
};
-&mmc3_pins_a {
- /* AP6210 requires pull-up */
- bias-pull-up;
-};
-
&ohci0 {
status = "okay";
};
};
&pio {
- ahci_pwr_pin_cubietruck: ahci_pwr_pin@1 {
- pins = "PH12";
- function = "gpio_out";
- };
-
- led_pins_cubietruck: led_pins@0 {
- pins = "PH7", "PH11", "PH20", "PH21";
- function = "gpio_out";
- };
-
- mmc3_pwrseq_pin_cubietruck: mmc3_pwrseq_pin@0 {
- pins = "PH9";
- function = "gpio_out";
- };
-
- usb0_vbus_pin_a: usb0_vbus_pin@0 {
- pins = "PH17";
- function = "gpio_out";
- };
-
- usb0_id_detect_pin: usb0_id_detect_pin@0 {
- pins = "PH19";
- function = "gpio_in";
- };
-
- usb0_vbus_detect_pin: usb0_vbus_detect_pin@0 {
- pins = "PH22";
- function = "gpio_in";
- };
+ /* Pin outputs low power clock for WiFi and BT */
+ pinctrl-0 = <&clk_out_a_pin>;
+ pinctrl-names = "default";
};
&pwm {
pinctrl-names = "default";
- pinctrl-0 = <&pwm0_pins_a>, <&pwm1_pins_a>;
+ pinctrl-0 = <&pwm0_pin>, <&pwm1_pin>;
status = "okay";
};
®_ahci_5v {
- pinctrl-0 = <&ahci_pwr_pin_cubietruck>;
gpio = <&pio 7 12 GPIO_ACTIVE_HIGH>;
status = "okay";
};
};
®_usb0_vbus {
- pinctrl-0 = <&usb0_vbus_pin_a>;
gpio = <&pio 7 17 GPIO_ACTIVE_HIGH>;
status = "okay";
};
&spdif {
pinctrl-names = "default";
- pinctrl-0 = <&spdif_tx_pins_a>;
+ pinctrl-0 = <&spdif_tx_pin>;
status = "okay";
};
&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_a>;
+ pinctrl-0 = <&uart0_pb_pins>;
+ status = "okay";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart2_pi_pins>, <&uart2_cts_rts_pi_pins>;
+ uart-has-rtscts;
status = "okay";
+
+ bluetooth {
+ compatible = "brcm,bcm20702a1";
+ clocks = <&ccu CLK_OUT_A>;
+ clock-names = "lpo";
+ device-wakeup-gpios = <&pio 7 24 GPIO_ACTIVE_LOW>; /* PH24 */
+ host-wakeup-gpios = <&pio 7 25 GPIO_ACTIVE_LOW>; /* PH25 */
+ shutdown-gpios = <&pio 7 18 GPIO_ACTIVE_HIGH>; /* PH18 */
+ max-speed = <1500000>;
+ };
};
&usb_otg {
};
&usbphy {
- pinctrl-names = "default";
- pinctrl-0 = <&usb0_id_detect_pin>, <&usb0_vbus_detect_pin>;
usb0_id_det-gpios = <&pio 7 19 GPIO_ACTIVE_HIGH>; /* PH19 */
usb0_vbus_det-gpios = <&pio 7 22 GPIO_ACTIVE_HIGH>; /* PH22 */
usb0_vbus_power-supply = <&usb_power_supply>;
reg_mmc3_vdd: mmc3_vdd {
compatible = "regulator-fixed";
- pinctrl-names = "default";
- pinctrl-0 = <&mmc3_vdd_pin_a20_hummingbird>;
regulator-name = "mmc3_vdd";
regulator-min-microvolt = <3000000>;
regulator-max-microvolt = <3000000>;
reg_gmac_vdd: gmac_vdd {
compatible = "regulator-fixed";
- pinctrl-names = "default";
- pinctrl-0 = <&gmac_vdd_pin_a20_hummingbird>;
regulator-name = "gmac_vdd";
regulator-min-microvolt = <3000000>;
regulator-max-microvolt = <3000000>;
&gmac {
pinctrl-names = "default";
- pinctrl-0 = <&gmac_pins_rgmii_a>;
+ pinctrl-0 = <&gmac_rgmii_pins>;
phy = <&phy1>;
phy-mode = "rgmii";
phy-supply = <®_gmac_vdd>;
};
&i2c0 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins_a>;
status = "okay";
axp209: pmic@34 {
};
&i2c1 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c1_pins_a>;
status = "okay";
};
&i2c2 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c2_pins_a>;
status = "okay";
};
&i2c3 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c3_pins_a>;
status = "okay";
};
&ir0 {
pinctrl-names = "default";
- pinctrl-0 = <&ir0_rx_pins_a>;
+ pinctrl-0 = <&ir0_rx_pin>;
status = "okay";
};
&mmc0 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>;
vmmc-supply = <®_vcc3v0>;
bus-width = <4>;
cd-gpios = <&pio 7 1 GPIO_ACTIVE_LOW>; /* PH1 */
};
&mmc3 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc3_pins_a>;
vmmc-supply = <®_mmc3_vdd>;
bus-width = <4>;
non-removable;
status = "okay";
};
-&pio {
- ahci_pwr_pin_a20_hummingbird: ahci_pwr_pin@0 {
- pins = "PH15";
- function = "gpio_out";
- };
-
- usb1_vbus_pin_a20_hummingbird: usb1_vbus_pin@0 {
- pins = "PH2";
- function = "gpio_out";
- };
-
- mmc3_vdd_pin_a20_hummingbird: mmc3_vdd_pin@0 {
- pins = "PH9";
- function = "gpio_out";
- };
-
- gmac_vdd_pin_a20_hummingbird: gmac_vdd_pin@0 {
- pins = "PH16";
- function = "gpio_out";
- };
-};
-
&pwm {
pinctrl-names = "default";
- pinctrl-0 = <&pwm0_pins_a>;
+ pinctrl-0 = <&pwm0_pin>;
status = "okay";
};
®_ahci_5v {
- pinctrl-0 = <&ahci_pwr_pin_a20_hummingbird>;
gpio = <&pio 7 15 GPIO_ACTIVE_HIGH>; /* PH15 */
status = "okay";
};
®_usb1_vbus {
- pinctrl-0 = <&usb1_vbus_pin_a20_hummingbird>;
gpio = <&pio 7 2 GPIO_ACTIVE_HIGH>; /* PH2 */
status = "okay";
};
&spi2 {
pinctrl-names = "default";
- pinctrl-0 = <&spi2_pins_b>,
- <&spi2_cs0_pins_b>;
+ pinctrl-0 = <&spi2_pb_pins>,
+ <&spi2_cs0_pb_pin>;
status = "okay";
};
&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_a>;
+ pinctrl-0 = <&uart0_pb_pins>;
status = "okay";
};
&uart2 {
pinctrl-names = "default";
- pinctrl-0 = <&uart2_pins_a>;
+ pinctrl-0 = <&uart2_pi_pins>, <&uart2_cts_rts_pi_pins>;
status = "okay";
};
&uart3 {
pinctrl-names = "default";
- pinctrl-0 = <&uart3_pins_a>;
+ pinctrl-0 = <&uart3_pg_pins>, <&uart3_cts_rts_pg_pins>;
status = "okay";
};
&uart4 {
pinctrl-names = "default";
- pinctrl-0 = <&uart4_pins_a>;
+ pinctrl-0 = <&uart4_pg_pins>;
status = "okay";
};
&uart5 {
pinctrl-names = "default";
- pinctrl-0 = <&uart5_pins_a>;
+ pinctrl-0 = <&uart5_pi_pins>;
status = "okay";
};
leds {
compatible = "gpio-leds";
- pinctrl-names = "default";
- pinctrl-0 = <&led_pins_i12_tvbox>;
red {
label = "i12_tvbox:red:usr";
reg_vmmc3: vmmc3 {
compatible = "regulator-fixed";
- pinctrl-names = "default";
- pinctrl-0 = <&vmmc3_pin_i12_tvbox>;
regulator-name = "vmmc3";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
reg_vmmc3_io: vmmc3-io {
compatible = "regulator-fixed";
- pinctrl-names = "default";
- pinctrl-0 = <&vmmc3_io_pin_i12_tvbox>;
regulator-name = "vmmc3-io";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
reg_gmac_3v3: gmac-3v3 {
compatible = "regulator-fixed";
- pinctrl-names = "default";
- pinctrl-0 = <&gmac_power_pin_i12_tvbox>;
regulator-name = "gmac-3v3";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
&gmac {
pinctrl-names = "default";
- pinctrl-0 = <&gmac_pins_mii_a>;
+ pinctrl-0 = <&gmac_mii_pins>;
phy = <&phy1>;
phy-mode = "mii";
phy-supply = <®_gmac_3v3>;
};
&i2c0 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins_a>;
status = "okay";
axp209: pmic@34 {
&ir0 {
pinctrl-names = "default";
- pinctrl-0 = <&ir0_rx_pins_a>;
+ pinctrl-0 = <&ir0_rx_pin>;
status = "okay";
};
&mmc0 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>;
vmmc-supply = <®_vcc3v3>;
bus-width = <4>;
cd-gpios = <&pio 7 1 GPIO_ACTIVE_LOW>; /* PH1 */
};
&mmc3 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc3_pins_a>;
vmmc-supply = <®_vmmc3>;
bus-width = <4>;
non-removable;
};
};
-&mmc3_pins_a {
- /* AP6210 / AP6330 requires pull-up */
- bias-pull-up;
-};
-
&ohci0 {
status = "okay";
};
status = "okay";
};
-&pio {
- vmmc3_pin_i12_tvbox: vmmc3_pin@0 {
- pins = "PH2";
- function = "gpio_out";
- };
-
- vmmc3_io_pin_i12_tvbox: vmmc3_io_pin@0 {
- pins = "PH12";
- function = "gpio_out";
- };
-
- gmac_power_pin_i12_tvbox: gmac_power_pin@0 {
- pins = "PH21";
- function = "gpio_out";
- };
-
- led_pins_i12_tvbox: led_pins@0 {
- pins = "PH9", "PH20";
- function = "gpio_out";
- };
-};
-
®_usb1_vbus {
status = "okay";
};
&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_a>;
+ pinctrl-0 = <&uart0_pb_pins>;
status = "okay";
};
&gmac {
pinctrl-names = "default";
- pinctrl-0 = <&gmac_pins_mii_a>;
+ pinctrl-0 = <&gmac_mii_pins>;
phy = <&phy1>;
phy-mode = "mii";
status = "okay";
};
&i2c0 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins_a>;
status = "okay";
axp209: pmic@34 {
};
&i2c1 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c1_pins_a>;
status = "okay";
};
&mmc0 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>;
vmmc-supply = <®_vcc3v3>;
bus-width = <4>;
cd-gpios = <&pio 8 5 GPIO_ACTIVE_LOW>; /* PI5 */
&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_a>;
+ pinctrl-0 = <&uart0_pb_pins>;
status = "okay";
};
&gmac {
pinctrl-names = "default";
- pinctrl-0 = <&gmac_pins_mii_a>;
+ pinctrl-0 = <&gmac_mii_pins>;
phy = <&phy1>;
phy-mode = "mii";
status = "okay";
&ir0 {
pinctrl-names = "default";
- pinctrl-0 = <&ir0_rx_pins_a>;
+ pinctrl-0 = <&ir0_rx_pin>;
status = "okay";
};
&mmc0 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>;
vmmc-supply = <®_vcc3v3>;
bus-width = <4>;
cd-gpios = <&pio 7 1 GPIO_ACTIVE_LOW>; /* PH1 */
};
&pio {
- led_pins_itead_core: led_pins@0 {
+ led_pins_itead_core: led-pins {
pins = "PH20","PH21";
function = "gpio_out";
drive-strength = <20>;
&spdif {
pinctrl-names = "default";
- pinctrl-0 = <&spdif_tx_pins_a>;
+ pinctrl-0 = <&spdif_tx_pin>;
status = "okay";
};
leds {
compatible = "gpio-leds";
- pinctrl-names = "default";
- pinctrl-0 = <&led_pins_lamobo_r1>;
green {
label = "lamobo_r1:green:usr";
reg_gmac_3v3: gmac-3v3 {
compatible = "regulator-fixed";
- pinctrl-names = "default";
- pinctrl-0 = <&gmac_power_pin_lamobo_r1>;
regulator-name = "gmac-3v3";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
&gmac {
pinctrl-names = "default";
- pinctrl-0 = <&gmac_pins_rgmii_a>;
+ pinctrl-0 = <&gmac_rgmii_pins>;
phy-mode = "rgmii";
phy-supply = <®_gmac_3v3>;
status = "okay";
+ /delete-property/#address-cells;
+ /delete-property/#size-cells;
fixed-link {
speed = <1000>;
switch: ethernet-switch@1e {
compatible = "brcm,bcm53125";
reg = <30>;
- #address-cells = <1>;
- #size-cells = <0>;
ports {
#address-cells = <1>;
};
&i2c0 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins_a>;
status = "okay";
axp209: pmic@34 {
};
&i2c2 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c2_pins_a>;
status = "okay";
};
&ir0 {
pinctrl-names = "default";
- pinctrl-0 = <&ir0_rx_pins_a>;
+ pinctrl-0 = <&ir0_rx_pin>;
status = "okay";
};
&mmc0 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_lamobo_r1>;
vmmc-supply = <®_vcc3v3>;
bus-width = <4>;
cd-gpios = <&pio 7 10 GPIO_ACTIVE_LOW>; /* PH10 */
};
&pio {
- usb0_id_detect_pin: usb0_id_detect_pin@0 {
+ usb0_id_detect_pin: usb0-id-detect-pin {
pins = "PH4";
function = "gpio_in";
bias-pull-up;
};
-
- mmc0_cd_pin_lamobo_r1: mmc0_cd_pin@0 {
- pins = "PH10";
- function = "gpio_in";
- bias-pull-up;
- };
-
- gmac_power_pin_lamobo_r1: gmac_power_pin@0 {
- pins = "PH23";
- function = "gpio_out";
- };
-
- led_pins_lamobo_r1: led_pins@0 {
- pins = "PH24";
- function = "gpio_out";
- };
};
#include "axp209.dtsi"
&spi0 {
pinctrl-names = "default";
- pinctrl-0 = <&spi0_pins_a>,
- <&spi0_cs0_pins_a>,
- <&spi0_cs1_pins_a>;
+ pinctrl-0 = <&spi0_pi_pins>,
+ <&spi0_cs0_pi_pin>,
+ <&spi0_cs1_pi_pin>;
status = "okay";
};
&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_a>;
+ pinctrl-0 = <&uart0_pb_pins>;
status = "okay";
};
&uart3 {
pinctrl-names = "default";
- pinctrl-0 = <&uart3_pins_b>;
+ pinctrl-0 = <&uart3_ph_pins>;
status = "okay";
};
&uart7 {
pinctrl-names = "default";
- pinctrl-0 = <&uart7_pins_a>;
+ pinctrl-0 = <&uart7_pi_pins>;
status = "okay";
};
leds {
compatible = "gpio-leds";
- pinctrl-names = "default";
- pinctrl-0 = <&led_pins_m3>;
blue {
label = "m3:blue:usr";
&gmac {
pinctrl-names = "default";
- pinctrl-0 = <&gmac_pins_mii_a>;
+ pinctrl-0 = <&gmac_mii_pins>;
phy = <&phy1>;
phy-mode = "mii";
status = "okay";
};
&i2c0 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins_a>;
status = "okay";
axp209: pmic@34 {
&ir0 {
pinctrl-names = "default";
- pinctrl-0 = <&ir0_rx_pins_a>;
+ pinctrl-0 = <&ir0_rx_pin>;
status = "okay";
};
&mmc0 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>;
vmmc-supply = <®_vcc3v3>;
bus-width = <4>;
cd-gpios = <&pio 7 1 GPIO_ACTIVE_LOW>; /* PH1 */
};
&mmc2 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc2_pins_a>;
vmmc-supply = <®_vcc3v3>;
bus-width = <4>;
non-removable;
status = "okay";
};
-&pio {
- led_pins_m3: led_pins@0 {
- pins = "PH20";
- function = "gpio_out";
- };
-};
-
®_usb1_vbus {
status = "okay";
};
&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_a>;
+ pinctrl-0 = <&uart0_pb_pins>;
status = "okay";
};
&gmac {
pinctrl-names = "default";
- pinctrl-0 = <&gmac_pins_mii_a>;
+ pinctrl-0 = <&gmac_rgmii_pins>;
phy = <&phy1>;
phy-mode = "mii";
status = "okay";
&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_a>;
+ pinctrl-0 = <&uart0_pb_pins>;
status = "okay";
};
};
&i2c0 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins_a>;
status = "okay";
axp209: pmic@34 {
};
&i2c1 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c1_pins_a>;
status = "okay";
};
&i2c2 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c2_pins_a>;
status = "okay";
};
&mmc0 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>;
vmmc-supply = <®_vcc3v0>;
bus-width = <4>;
cd-gpios = <&pio 7 1 GPIO_ACTIVE_LOW>; /* PH1 */
status = "okay";
};
-&pio {
- usb0_id_detect_pin: usb0_id_detect_pin@0 {
- pins = "PH4";
- function = "gpio_in";
- };
-
- usb0_vbus_detect_pin: usb0_vbus_detect_pin@0 {
- pins = "PH5";
- function = "gpio_in";
- };
-};
-
®_usb0_vbus {
status = "okay";
};
&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_a>;
+ pinctrl-0 = <&uart0_pb_pins>;
status = "okay";
};
&uart2 {
pinctrl-names = "default";
- pinctrl-0 = <&uart2_pins_a>;
+ pinctrl-0 = <&uart2_pi_pins>, <&uart2_cts_rts_pi_pins>;
status = "okay";
};
};
&usbphy {
- pinctrl-names = "default";
- pinctrl-0 = <&usb0_id_detect_pin>, <&usb0_vbus_detect_pin>;
usb0_id_det-gpios = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */
usb0_vbus_det-gpios = <&pio 7 5 GPIO_ACTIVE_HIGH>; /* PH5 */
usb0_vbus-supply = <®_usb0_vbus>;
--- /dev/null
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Device Tree Source for A20-Olimex-SOM-EVB-eMMC Board
+ *
+ * Copyright (C) 2018 Olimex Ltd.
+ * Author: Stefan Mavrodiev <stefan@olimex.com>
+ */
+
+/dts-v1/;
+#include "sun7i-a20-olimex-som-evb.dts"
+
+/ {
+
+ model = "Olimex A20-Olimex-SOM-EVB-eMMC";
+ compatible = "olimex,a20-olimex-som-evb-emmc", "allwinner,sun7i-a20";
+
+ mmc2_pwrseq: mmc2_pwrseq {
+ compatible = "mmc-pwrseq-emmc";
+ reset-gpios = <&pio 2 18 GPIO_ACTIVE_LOW>;
+ };
+};
+
+&mmc2 {
+ vmmc-supply = <®_vcc3v3>;
+ mmc-pwrseq = <&mmc2_pwrseq>;
+ bus-width = <4>;
+ non-removable;
+ status = "okay";
+
+ emmc: emmc@0 {
+ reg = <0>;
+ compatible = "mmc-card";
+ broken-hpi;
+ };
+};
leds {
compatible = "gpio-leds";
- pinctrl-names = "default";
- pinctrl-0 = <&led_pins_olimex_som_evb>;
green {
label = "a20-olimex-som-evb:green:usr";
&gmac {
pinctrl-names = "default";
- pinctrl-0 = <&gmac_pins_rgmii_a>;
+ pinctrl-0 = <&gmac_rgmii_pins>;
phy = <&phy1>;
phy-mode = "rgmii";
status = "okay";
};
&i2c0 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins_a>;
status = "okay";
axp209: pmic@34 {
};
&i2c1 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c1_pins_a>;
status = "okay";
};
&i2c2 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c2_pins_a>;
status = "okay";
};
vref-supply = <®_vcc3v0>;
status = "okay";
- button@190 {
+ button-190 {
label = "Volume Up";
linux,code = <KEY_VOLUMEUP>;
channel = <0>;
voltage = <190000>;
};
- button@390 {
+ button-390 {
label = "Volume Down";
linux,code = <KEY_VOLUMEDOWN>;
channel = <0>;
voltage = <390000>;
};
- button@600 {
+ button-600 {
label = "Menu";
linux,code = <KEY_MENU>;
channel = <0>;
voltage = <600000>;
};
- button@800 {
+ button-800 {
label = "Search";
linux,code = <KEY_SEARCH>;
channel = <0>;
voltage = <800000>;
};
- button@980 {
+ button-980 {
label = "Home";
linux,code = <KEY_HOMEPAGE>;
channel = <0>;
voltage = <980000>;
};
- button@1180 {
+ button-1180 {
label = "Esc";
linux,code = <KEY_ESC>;
channel = <0>;
voltage = <1180000>;
};
- button@1400 {
+ button-1400 {
label = "Enter";
linux,code = <KEY_ENTER>;
channel = <0>;
};
&mmc0 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>;
vmmc-supply = <®_vcc3v3>;
bus-width = <4>;
cd-gpios = <&pio 7 1 GPIO_ACTIVE_LOW>; /* PH1 */
};
&mmc3 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc3_pins_a>, <&mmc3_cd_pin_olimex_som_evb>;
vmmc-supply = <®_vcc3v3>;
bus-width = <4>;
cd-gpios = <&pio 7 0 GPIO_ACTIVE_LOW>; /* PH0 */
};
&pio {
- ahci_pwr_pin_olimex_som_evb: ahci_pwr_pin@1 {
- pins = "PC3";
- function = "gpio_out";
- };
-
- led_pins_olimex_som_evb: led_pins@0 {
+ led_pins_olimex_som_evb: led-pins {
pins = "PH2";
function = "gpio_out";
drive-strength = <20>;
};
-
- mmc3_cd_pin_olimex_som_evb: mmc3_cd_pin@0 {
- pins = "PH0";
- function = "gpio_in";
- bias-pull-up;
- };
-
- usb0_id_detect_pin: usb0_id_detect_pin@0 {
- pins = "PH4";
- function = "gpio_in";
- };
-
- usb0_vbus_detect_pin: usb0_vbus_detect_pin@0 {
- pins = "PH5";
- function = "gpio_in";
- };
};
®_ahci_5v {
- pinctrl-0 = <&ahci_pwr_pin_olimex_som_evb>;
gpio = <&pio 2 3 GPIO_ACTIVE_HIGH>;
status = "okay";
};
&spi1 {
pinctrl-names = "default";
- pinctrl-0 = <&spi1_pins_a>,
- <&spi1_cs0_pins_a>;
+ pinctrl-0 = <&spi1_pi_pins>,
+ <&spi1_cs0_pi_pin>;
status = "okay";
};
&spi2 {
pinctrl-names = "default";
- pinctrl-0 = <&spi2_pins_a>,
- <&spi2_cs0_pins_a>;
+ pinctrl-0 = <&spi2_pc_pins>,
+ <&spi2_cs0_pc_pin>;
status = "okay";
};
&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_a>;
+ pinctrl-0 = <&uart0_pb_pins>;
status = "okay";
};
&uart6 {
pinctrl-names = "default";
- pinctrl-0 = <&uart6_pins_a>;
+ pinctrl-0 = <&uart6_pi_pins>;
status = "okay";
};
&uart7 {
pinctrl-names = "default";
- pinctrl-0 = <&uart7_pins_a>;
+ pinctrl-0 = <&uart7_pi_pins>;
status = "okay";
};
};
&usbphy {
- pinctrl-names = "default";
- pinctrl-0 = <&usb0_id_detect_pin>, <&usb0_vbus_detect_pin>;
usb0_id_det-gpios = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH04 */
usb0_vbus_det-gpios = <&pio 7 5 GPIO_ACTIVE_HIGH>; /* PH05 */
usb0_vbus-supply = <®_usb0_vbus>;
};
&mmc2 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc2_pins_a>;
vmmc-supply = <®_vcc3v3>;
mmc-pwrseq = <&mmc2_pwrseq>;
bus-width = <4>;
&can0 {
pinctrl-names = "default";
- pinctrl-0 = <&can0_pins_a>;
+ pinctrl-0 = <&can_ph_pins>;
status = "okay";
};
&gmac {
pinctrl-names = "default";
- pinctrl-0 = <&gmac_pins_rgmii_a>;
+ pinctrl-0 = <&gmac_rgmii_pins>;
phy = <&phy3>;
phy-mode = "rgmii";
phy-supply = <®_vcc3v3>;
};
&i2c0 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins_a>;
status = "okay";
axp209: pmic@34 {
/* Exposed to UEXT1 */
&i2c1 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c1_pins_a>;
status = "okay";
eeprom: eeprom@50 {
/* Exposed to UEXT2 */
&i2c2 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c2_pins_a>;
status = "okay";
};
&ir0 {
pinctrl-names = "default";
- pinctrl-0 = <&ir0_rx_pins_a>;
+ pinctrl-0 = <&ir0_rx_pin>;
status = "okay";
};
&mmc0 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>;
vmmc-supply = <®_vcc3v3>;
bus-width = <4>;
cd-gpios = <&pio 7 1 GPIO_ACTIVE_LOW>;
};
&mmc3 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc3_pins_a>;
vmmc-supply = <®_vcc3v3>;
mmc-pwrseq = <&rtl_pwrseq>;
bus-width = <4>;
};
&pio {
- bt_uart_pins: bt_uart_pins@0 {
- pins = "PG6", "PG7", "PG8";
+ uart3_rts_pin: uart3-rts-pin {
+ pins = "PG8";
function = "uart3";
};
};
/* Exposed to UEXT1 */
&spi1 {
pinctrl-names = "default";
- pinctrl-0 = <&spi1_pins_a>,
- <&spi1_cs0_pins_a>;
+ pinctrl-0 = <&spi1_pi_pins>,
+ <&spi1_cs0_pi_pin>;
status = "okay";
};
/* Exposed to UEXT2 */
&spi2 {
pinctrl-names = "default";
- pinctrl-0 = <&spi2_pins_a>,
- <&spi2_cs0_pins_a>;
+ pinctrl-0 = <&spi2_pc_pins>,
+ <&spi2_cs0_pc_pin>;
status = "okay";
};
&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_a>;
+ pinctrl-0 = <&uart0_pb_pins>;
status = "okay";
};
/* Used for RTL8723BS bluetooth */
&uart3 {
pinctrl-names = "default";
- pinctrl-0 = <&bt_uart_pins>;
+ pinctrl-0 = <&uart3_pg_pins>, <&uart3_rts_pin>;
status = "okay";
};
/* Exposed to UEXT1 */
&uart4 {
pinctrl-names = "default";
- pinctrl-0 = <&uart4_pins_a>;
+ pinctrl-0 = <&uart4_pg_pins>;
status = "okay";
};
/* Exposed to UEXT2 */
&uart7 {
pinctrl-names = "default";
- pinctrl-0 = <&uart7_pins_a>;
+ pinctrl-0 = <&uart7_pi_pins>;
status = "okay";
};
&gmac {
pinctrl-names = "default";
- pinctrl-0 = <&gmac_pins_mii_a>;
+ pinctrl-0 = <&gmac_mii_pins>;
phy = <&phy1>;
phy-mode = "mii";
status = "okay";
};
&i2c0 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins_a>;
status = "okay";
axp209: pmic@34 {
};
&i2c1 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c1_pins_a>;
status = "okay";
eeprom: eeprom@50 {
};
&mmc0 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>;
vmmc-supply = <®_vcc3v3>;
bus-width = <4>;
cd-gpios = <&pio 7 1 GPIO_ACTIVE_LOW>; /* PH1 */
};
&pio {
- ahci_pwr_pin_olinuxinolime: ahci_pwr_pin@1 {
- pins = "PC3";
- function = "gpio_out";
- };
-
- led_pins_olinuxinolime: led_pins@0 {
+ led_pins_olinuxinolime: led-pins {
pins = "PH2";
function = "gpio_out";
drive-strength = <20>;
};
- usb0_id_detect_pin: usb0_id_detect_pin@0 {
+ usb0_id_detect_pin: usb0-id-detect-pin {
pins = "PH4";
function = "gpio_in";
bias-pull-up;
};
- usb0_vbus_detect_pin: usb0_vbus_detect_pin@0 {
+ usb0_vbus_detect_pin: usb0-vbus-detect-pin {
pins = "PH5";
function = "gpio_in";
bias-pull-down;
};
®_ahci_5v {
- pinctrl-0 = <&ahci_pwr_pin_olinuxinolime>;
gpio = <&pio 2 3 GPIO_ACTIVE_HIGH>;
status = "okay";
};
&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_a>;
+ pinctrl-0 = <&uart0_pb_pins>;
status = "okay";
};
compatible = "olimex,a20-olinuxino-lime2-emmc", "allwinner,sun7i-a20";
mmc2_pwrseq: pwrseq {
- pinctrl-0 = <&mmc2_pins_nrst>;
- pinctrl-names = "default";
compatible = "mmc-pwrseq-emmc";
reset-gpios = <&pio 2 16 GPIO_ACTIVE_LOW>;
};
};
-&pio {
- mmc2_pins_nrst: mmc2-rst-pin {
- pins = "PC16";
- function = "gpio_out";
- };
-};
-
&mmc2 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc2_pins_a>;
vmmc-supply = <®_vcc3v3>;
vqmmc-supply = <®_vcc3v3>;
bus-width = <4>;
&gmac {
pinctrl-names = "default";
- pinctrl-0 = <&gmac_pins_rgmii_a>;
+ pinctrl-0 = <&gmac_rgmii_pins>;
phy = <&phy1>;
phy-mode = "rgmii";
status = "okay";
};
&i2c0 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins_a>;
status = "okay";
axp209: pmic@34 {
};
&i2c1 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c1_pins_a>;
status = "okay";
eeprom: eeprom@50 {
};
};
+&lradc {
+ vref-supply = <®_vcc3v0>;
+};
+
&mmc0 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>;
vmmc-supply = <®_vcc3v3>;
bus-width = <4>;
cd-gpios = <&pio 7 1 GPIO_ACTIVE_LOW>; /* PH1 */
};
&pio {
- ahci_pwr_pin_olinuxinolime: ahci_pwr_pin@1 {
- pins = "PC3";
- function = "gpio_out";
- };
-
- led_pins_olinuxinolime: led_pins@0 {
+ led_pins_olinuxinolime: led-pins {
pins = "PH2";
function = "gpio_out";
drive-strength = <20>;
};
- usb0_id_detect_pin: usb0_id_detect_pin@0 {
+ usb0_id_detect_pin: usb0-id-detect-pin {
pins = "PH4";
function = "gpio_in";
bias-pull-up;
};
- usb0_vbus_detect_pin: usb0_vbus_detect_pin@0 {
+ usb0_vbus_detect_pin: usb0-vbus-detect-pin {
pins = "PH5";
function = "gpio_in";
bias-pull-down;
};
-
- usb0_vbus_pin_lime2: usb0_vbus_pin@0 {
- pins = "PC17";
- function = "gpio_out";
- };
};
®_ahci_5v {
- pinctrl-0 = <&ahci_pwr_pin_olinuxinolime>;
gpio = <&pio 2 3 GPIO_ACTIVE_HIGH>;
status = "okay";
};
regulator-min-microvolt = <2800000>;
regulator-max-microvolt = <2800000>;
regulator-name = "vddio-csi0";
+ regulator-soft-start;
+ regulator-ramp-delay = <1600>;
};
®_ldo4 {
};
®_usb0_vbus {
- pinctrl-0 = <&usb0_vbus_pin_lime2>;
gpio = <&pio 2 17 GPIO_ACTIVE_HIGH>;
status = "okay";
};
&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_a>;
+ pinctrl-0 = <&uart0_pb_pins>;
status = "okay";
};
};
&mmc2 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc2_pins_a>;
vmmc-supply = <®_vcc3v3>;
bus-width = <4>;
non-removable;
&gmac {
pinctrl-names = "default";
- pinctrl-0 = <&gmac_pins_mii_a>, <&gmac_txerr>;
+ pinctrl-0 = <&gmac_mii_pins>, <&gmac_txerr>;
phy = <&phy1>;
phy-mode = "mii";
status = "okay";
};
&i2c0 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins_a>;
status = "okay";
axp209: pmic@34 {
};
&i2c1 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c1_pins_a>;
status = "okay";
eeprom: eeprom@50 {
};
&i2c2 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c2_pins_a>;
status = "okay";
};
vref-supply = <®_vcc3v0>;
status = "okay";
- button@191 {
+ button-191 {
label = "Volume Up";
linux,code = <KEY_VOLUMEUP>;
channel = <0>;
voltage = <191274>;
};
- button@392 {
+ button-392 {
label = "Volume Down";
linux,code = <KEY_VOLUMEDOWN>;
channel = <0>;
voltage = <392644>;
};
- button@601 {
+ button-601 {
label = "Menu";
linux,code = <KEY_MENU>;
channel = <0>;
voltage = <601151>;
};
- button@795 {
+ button-795 {
label = "Search";
linux,code = <KEY_SEARCH>;
channel = <0>;
voltage = <795090>;
};
- button@987 {
+ button-987 {
label = "Home";
linux,code = <KEY_HOMEPAGE>;
channel = <0>;
voltage = <987387>;
};
- button@1184 {
+ button-1184 {
label = "Esc";
linux,code = <KEY_ESC>;
channel = <0>;
voltage = <1184678>;
};
- button@1398 {
+ button-1398 {
label = "Enter";
linux,code = <KEY_ENTER>;
channel = <0>;
};
&mmc0 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>;
vmmc-supply = <®_vcc3v3>;
bus-width = <4>;
cd-gpios = <&pio 7 1 GPIO_ACTIVE_LOW>; /* PH1 */
};
&mmc3 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc3_pins_a>, <&mmc3_cd_pin_olinuxinom>;
vmmc-supply = <®_vcc3v3>;
bus-width = <4>;
cd-gpios = <&pio 7 11 GPIO_ACTIVE_LOW>; /* PH11 */
};
&pio {
- gmac_txerr: gmac_txerr@0 {
+ gmac_txerr: gmac-txerr-pin {
pins = "PA17";
function = "gmac";
};
- mmc3_cd_pin_olinuxinom: mmc3_cd_pin@0 {
- pins = "PH11";
- function = "gpio_in";
- bias-pull-up;
- };
-
- led_pins_olinuxino: led_pins@0 {
+ led_pins_olinuxino: led-pins {
pins = "PH2";
function = "gpio_out";
drive-strength = <20>;
};
- usb0_id_detect_pin: usb0_id_detect_pin@0 {
+ usb0_id_detect_pin: usb0-id-detect-pin {
pins = "PH4";
function = "gpio_in";
bias-pull-up;
};
- usb0_vbus_detect_pin: usb0_vbus_detect_pin@0 {
+ usb0_vbus_detect_pin: usb0-vbus-detect-pin {
pins = "PH5";
function = "gpio_in";
bias-pull-down;
&spi1 {
pinctrl-names = "default";
- pinctrl-0 = <&spi1_pins_a>,
- <&spi1_cs0_pins_a>;
+ pinctrl-0 = <&spi1_pi_pins>,
+ <&spi1_cs0_pi_pin>;
status = "okay";
};
&spi2 {
pinctrl-names = "default";
- pinctrl-0 = <&spi2_pins_a>,
- <&spi2_cs0_pins_a>;
+ pinctrl-0 = <&spi2_pc_pins>,
+ <&spi2_cs0_pc_pin>;
status = "okay";
};
&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_a>;
+ pinctrl-0 = <&uart0_pb_pins>;
status = "okay";
};
&uart6 {
pinctrl-names = "default";
- pinctrl-0 = <&uart6_pins_a>;
+ pinctrl-0 = <&uart6_pi_pins>;
status = "okay";
};
&uart7 {
pinctrl-names = "default";
- pinctrl-0 = <&uart7_pins_a>;
+ pinctrl-0 = <&uart7_pi_pins>;
status = "okay";
};
leds {
compatible = "gpio-leds";
- pinctrl-names = "default";
- pinctrl-0 = <&led_pins_orangepi>;
green {
label = "orangepi:green:usr";
reg_gmac_3v3: gmac-3v3 {
compatible = "regulator-fixed";
- pinctrl-names = "default";
- pinctrl-0 = <&gmac_power_pin_orangepi>;
regulator-name = "gmac-3v3";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
&gmac {
pinctrl-names = "default";
- pinctrl-0 = <&gmac_pins_rgmii_a>;
+ pinctrl-0 = <&gmac_rgmii_pins>;
phy = <&phy1>;
phy-mode = "rgmii";
phy-supply = <®_gmac_3v3>;
};
&i2c0 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins_a>;
status = "okay";
axp209: pmic@34 {
&ir0 {
pinctrl-names = "default";
- pinctrl-0 = <&ir0_rx_pins_a>;
+ pinctrl-0 = <&ir0_rx_pin>;
status = "okay";
};
&mmc0 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_orangepi>;
vmmc-supply = <®_vcc3v3>;
bus-width = <4>;
cd-gpios = <&pio 7 10 GPIO_ACTIVE_LOW>; /* PH10 */
};
&mmc3 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc3_pins_a>, <&mmc3_cd_pin_orangepi>;
vmmc-supply = <®_vcc3v3>;
bus-width = <4>;
cd-gpios = <&pio 7 11 GPIO_ACTIVE_LOW>; /* PH11 */
};
&pio {
- usb0_id_detect_pin: usb0_id_detect_pin@0 {
+ usb0_id_detect_pin: usb0-id-detect-pin {
pins = "PH4";
function = "gpio_in";
bias-pull-up;
};
-
- mmc0_cd_pin_orangepi: mmc0_cd_pin@0 {
- pins = "PH10";
- function = "gpio_in";
- bias-pull-up;
- };
-
- mmc3_cd_pin_orangepi: mmc3_cd_pin@0 {
- pins = "PH11";
- function = "gpio_in";
- bias-pull-up;
- };
-
- usb2_vbus_pin_bananapro: usb2_vbus_pin@0 {
- pins = "PH22";
- function = "gpio_out";
- };
-
- gmac_power_pin_orangepi: gmac_power_pin@0 {
- pins = "PH23";
- function = "gpio_out";
- };
-
- led_pins_orangepi: led_pins@0 {
- pins = "PH24", "PH25";
- function = "gpio_out";
- };
-
- usb1_vbus_pin_bananapro: usb1_vbus_pin@0 {
- pins = "PH26";
- function = "gpio_out";
- };
};
®_dcdc2 {
};
®_usb1_vbus {
- pinctrl-0 = <&usb1_vbus_pin_bananapro>;
gpio = <&pio 7 26 GPIO_ACTIVE_HIGH>; /* PH26 */
status = "okay";
};
®_usb2_vbus {
- pinctrl-0 = <&usb2_vbus_pin_bananapro>;
gpio = <&pio 7 22 GPIO_ACTIVE_HIGH>; /* PH22 */
status = "okay";
};
&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_a>;
+ pinctrl-0 = <&uart0_pb_pins>;
status = "okay";
};
leds {
compatible = "gpio-leds";
- pinctrl-names = "default";
- pinctrl-0 = <&led_pins_orangepi>;
green {
label = "orangepi:green:usr";
reg_gmac_3v3: gmac-3v3 {
compatible = "regulator-fixed";
- pinctrl-names = "default";
- pinctrl-0 = <&gmac_power_pin_orangepi>;
regulator-name = "gmac-3v3";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
&gmac {
pinctrl-names = "default";
- pinctrl-0 = <&gmac_pins_rgmii_a>;
+ pinctrl-0 = <&gmac_rgmii_pins>;
phy = <&phy1>;
phy-mode = "rgmii";
phy-supply = <®_gmac_3v3>;
};
&i2c0 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins_a>;
status = "okay";
axp209: pmic@34 {
&ir0 {
pinctrl-names = "default";
- pinctrl-0 = <&ir0_rx_pins_a>;
+ pinctrl-0 = <&ir0_rx_pin>;
status = "okay";
};
&mmc0 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_orangepi>;
vmmc-supply = <®_vcc3v3>;
bus-width = <4>;
cd-gpios = <&pio 7 10 GPIO_ACTIVE_LOW>; /* PH10 */
};
&pio {
- usb0_id_detect_pin: usb0_id_detect_pin@0 {
+ usb0_id_detect_pin: usb0-id-detect-pin {
pins = "PH4";
function = "gpio_in";
bias-pull-up;
};
-
- mmc0_cd_pin_orangepi: mmc0_cd_pin@0 {
- pins = "PH10";
- function = "gpio_in";
- bias-pull-up;
- };
-
- usb2_vbus_pin_bananapro: usb2_vbus_pin@0 {
- pins = "PH22";
- function = "gpio_out";
- };
-
- gmac_power_pin_orangepi: gmac_power_pin@0 {
- pins = "PH23";
- function = "gpio_out";
- };
-
- led_pins_orangepi: led_pins@0 {
- pins = "PH24";
- function = "gpio_out";
- };
-
- usb1_vbus_pin_bananapro: usb1_vbus_pin@0 {
- pins = "PH26";
- function = "gpio_out";
- };
};
®_dcdc2 {
};
®_usb1_vbus {
- pinctrl-0 = <&usb1_vbus_pin_bananapro>;
gpio = <&pio 7 26 GPIO_ACTIVE_HIGH>; /* PH26 */
status = "okay";
};
®_usb2_vbus {
- pinctrl-0 = <&usb2_vbus_pin_bananapro>;
gpio = <&pio 7 22 GPIO_ACTIVE_HIGH>; /* PH22 */
status = "okay";
};
&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_a>;
+ pinctrl-0 = <&uart0_pb_pins>;
status = "okay";
};
leds {
compatible = "gpio-leds";
- pinctrl-names = "default";
- pinctrl-0 = <&led_pins_pcduino3_nano>;
/* Marked "LED3" on the PCB. */
usr1 {
&gmac {
pinctrl-names = "default";
- pinctrl-0 = <&gmac_pins_rgmii_a>;
+ pinctrl-0 = <&gmac_rgmii_pins>;
phy = <&phy1>;
phy-mode = "rgmii";
status = "okay";
};
&i2c0 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins_a>;
status = "okay";
axp209: pmic@34 {
&ir0 {
pinctrl-names = "default";
- pinctrl-0 = <&ir0_rx_pins_a>;
+ pinctrl-0 = <&ir0_rx_pin>;
status = "okay";
};
&mmc0 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>;
vmmc-supply = <®_vcc3v3>;
bus-width = <4>;
cd-gpios = <&pio 7 1 GPIO_ACTIVE_LOW>; /* PH1 */
};
&pio {
- ahci_pwr_pin_pcduino3_nano: ahci_pwr_pin@0 {
- pins = "PH2";
- function = "gpio_out";
- };
-
- led_pins_pcduino3_nano: led_pins@0 {
- pins = "PH16", "PH15";
- function = "gpio_out";
- };
-
- usb0_id_detect_pin: usb0_id_detect_pin@0 {
+ usb0_id_detect_pin: usb0-id-detect-pin {
pins = "PH4";
function = "gpio_in";
bias-pull-up;
};
-
- usb1_vbus_pin_pcduino3_nano: usb1_vbus_pin@0 {
- pins = "PD2";
- function = "gpio_out";
- };
};
®_ahci_5v {
- pinctrl-0 = <&ahci_pwr_pin_pcduino3_nano>;
gpio = <&pio 7 2 GPIO_ACTIVE_HIGH>; /* PH2 */
status = "okay";
};
/* A single regulator (U24) powers both USB host ports. */
®_usb1_vbus {
- pinctrl-0 = <&usb1_vbus_pin_pcduino3_nano>;
gpio = <&pio 3 2 GPIO_ACTIVE_HIGH>; /* PD2 */
status = "okay";
};
&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_a>;
+ pinctrl-0 = <&uart0_pb_pins>;
status = "okay";
};
leds {
compatible = "gpio-leds";
- pinctrl-names = "default";
- pinctrl-0 = <&led_pins_pcduino3>;
tx {
label = "pcduino3:green:tx";
};
};
- gpio_keys {
+ gpio-keys {
compatible = "gpio-keys";
- pinctrl-names = "default";
- pinctrl-0 = <&key_pins_pcduino3>;
- #address-cells = <1>;
- #size-cells = <0>;
- button@0 {
+
+ back {
label = "Key Back";
linux,code = <KEY_BACK>;
gpios = <&pio 7 17 GPIO_ACTIVE_LOW>;
};
- button@1 {
+
+ home {
label = "Key Home";
linux,code = <KEY_HOME>;
gpios = <&pio 7 18 GPIO_ACTIVE_LOW>;
};
- button@2 {
+
+ menu {
label = "Key Menu";
linux,code = <KEY_MENU>;
gpios = <&pio 7 19 GPIO_ACTIVE_LOW>;
&gmac {
pinctrl-names = "default";
- pinctrl-0 = <&gmac_pins_mii_a>;
+ pinctrl-0 = <&gmac_mii_pins>;
phy = <&phy1>;
phy-mode = "mii";
status = "okay";
};
&i2c0 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins_a>;
status = "okay";
axp209: pmic@34 {
&ir0 {
pinctrl-names = "default";
- pinctrl-0 = <&ir0_rx_pins_a>;
+ pinctrl-0 = <&ir0_rx_pin>;
status = "okay";
};
&mmc0 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>;
vmmc-supply = <®_vcc3v3>;
bus-width = <4>;
cd-gpios = <&pio 7 1 GPIO_ACTIVE_LOW>; /* PH1 */
};
&pio {
- led_pins_pcduino3: led_pins@0 {
- pins = "PH15", "PH16";
- function = "gpio_out";
- };
-
- key_pins_pcduino3: key_pins@0 {
- pins = "PH17", "PH18", "PH19";
- function = "gpio_in";
- };
-
- usb0_id_detect_pin: usb0_id_detect_pin@0 {
+ usb0_id_detect_pin: usb0-id-detect-pin {
pins = "PH4";
function = "gpio_in";
bias-pull-up;
&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_a>;
+ pinctrl-0 = <&uart0_pb_pins>;
status = "okay";
};
};
&mmc0 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>;
vmmc-supply = <®_vcc3v3>;
bus-width = <4>;
cd-gpios = <&pio 7 1 GPIO_ACTIVE_LOW>; /* PH1 */
&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_a>;
+ pinctrl-0 = <&uart0_pb_pins>;
status = "okay";
};
pwms = <&pwm 0 50000 PWM_POLARITY_INVERTED>;
brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>;
default-brightness-level = <8>;
- pinctrl-names = "default";
- pinctrl-0 = <&bl_enable_pin>;
enable-gpios = <&pio 7 7 GPIO_ACTIVE_HIGH>; /* PH7 */
};
};
&codec {
- pinctrl-names = "default";
- pinctrl-0 = <&codec_pa_pin>;
allwinner,pa-gpios = <&pio 7 15 GPIO_ACTIVE_HIGH>; /* PH15 */
status = "okay";
};
};
&i2c0 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins_a>;
status = "okay";
axp209: pmic@34 {
#include "axp209.dtsi"
&i2c1 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c1_pins_a>;
status = "okay";
};
&i2c2 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c2_pins_a>;
status = "okay";
gt911: touchscreen@5d {
reg = <0x5d>;
interrupt-parent = <&pio>;
interrupts = <7 21 IRQ_TYPE_EDGE_FALLING>; /* EINT21 (PH21) */
- pinctrl-names = "default";
- pinctrl-0 = <&ts_reset_pin>;
irq-gpios = <&pio 7 21 GPIO_ACTIVE_HIGH>; /* INT (PH21) */
reset-gpios = <&pio 1 13 GPIO_ACTIVE_HIGH>; /* RST (PB13) */
touchscreen-swapped-x-y;
vref-supply = <®_vcc3v0>;
status = "okay";
- button@571 {
+ button-571 {
label = "Volume Up";
linux,code = <KEY_VOLUMEUP>;
channel = <0>;
voltage = <571428>;
};
- button@761 {
+ button-761 {
label = "Volume Down";
linux,code = <KEY_VOLUMEDOWN>;
channel = <0>;
};
&mmc0 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>;
vmmc-supply = <®_vcc3v3>;
bus-width = <4>;
cd-gpios = <&pio 7 1 GPIO_ACTIVE_LOW>; /* PH1 */
};
&pio {
- bl_enable_pin: bl_enable_pin@0 {
- pins = "PH7";
- function = "gpio_out";
- };
-
- codec_pa_pin: codec_pa_pin@0 {
- pins = "PH15";
- function = "gpio_out";
- };
-
- ts_reset_pin: ts_reset_pin@0 {
- pins = "PB13";
- function = "gpio_out";
- };
-
- usb0_id_detect_pin: usb0_id_detect_pin@0 {
+ usb0_id_detect_pin: usb0-id-detect-pin {
pins = "PH4";
function = "gpio_in";
bias-pull-up;
&pwm {
pinctrl-names = "default";
- pinctrl-0 = <&pwm0_pins_a>;
+ pinctrl-0 = <&pwm0_pin>;
status = "okay";
};
&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_a>;
+ pinctrl-0 = <&uart0_pb_pins>;
status = "okay";
};
mmc3_pwrseq: mmc3_pwrseq {
compatible = "mmc-pwrseq-simple";
- pinctrl-names = "default";
- pinctrl-0 = <&vmmc3_pin_ap6xxx_wl_regon>;
reset-gpios = <&pio 7 9 GPIO_ACTIVE_LOW>; /* PH9 WIFI_EN */
};
};
&gmac {
pinctrl-names = "default";
- pinctrl-0 = <&gmac_pins_rgmii_a>;
+ pinctrl-0 = <&gmac_rgmii_pins>;
phy = <&phy1>;
phy-mode = "rgmii";
status = "okay";
};
&i2c0 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins_a>;
status = "okay";
axp209: pmic@34 {
};
&i2c1 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c1_pins_a>;
status = "okay";
};
&i2c2 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c2_pins_a>;
status = "okay";
};
#include "axp209.dtsi"
&mmc0 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>;
vmmc-supply = <®_vcc3v3>;
bus-width = <4>;
cd-gpios = <&pio 7 1 GPIO_ACTIVE_LOW>; /* PH1 */
};
&mmc3 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc3_pins_a>;
vmmc-supply = <®_vcc3v3>;
mmc-pwrseq = <&mmc3_pwrseq>;
bus-width = <4>;
};
&pio {
- vmmc3_pin_ap6xxx_wl_regon: vmmc3_pin@0 {
- pins = "PH9";
- function = "gpio_out";
- };
-
- usb0_id_detect_pin: usb0_id_detect_pin@0 {
+ usb0_id_detect_pin: usb0-id-detect-pin {
pins = "PH4";
function = "gpio_in";
bias-pull-up;
&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_a>;
+ pinctrl-0 = <&uart0_pb_pins>;
status = "okay";
};
&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_a>;
+ pinctrl-0 = <&uart0_pb_pins>;
status = "okay";
};
* OTHER DEALINGS IN THE SOFTWARE.
*/
-#include "skeleton.dtsi"
-
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/thermal/thermal.h>
#include <dt-bindings/dma/sun4i-a10.h>
/ {
interrupt-parent = <&gic>;
+ #address-cells = <1>;
+ #size-cells = <1>;
aliases {
ethernet0 = &gmac;
#size-cells = <1>;
ranges;
- framebuffer@0 {
+ framebuffer-lcd0-hdmi {
compatible = "allwinner,simple-framebuffer",
"simple-framebuffer";
allwinner,pipeline = "de_be0-lcd0-hdmi";
status = "disabled";
};
- framebuffer@1 {
+ framebuffer-lcd0 {
compatible = "allwinner,simple-framebuffer",
"simple-framebuffer";
allwinner,pipeline = "de_be0-lcd0";
status = "disabled";
};
- framebuffer@2 {
+ framebuffer-lcd0-tve0 {
compatible = "allwinner,simple-framebuffer",
"simple-framebuffer";
allwinner,pipeline = "de_be0-lcd0-tve0";
#cooling-cells = <2>;
};
- cpu@1 {
+ cpu1: cpu@1 {
compatible = "arm,cortex-a7";
device_type = "cpu";
reg = <1>;
+ clocks = <&ccu CLK_CPU>;
+ clock-latency = <244144>; /* 8 32k periods */
+ operating-points = <
+ /* kHz uV */
+ 960000 1400000
+ 912000 1400000
+ 864000 1300000
+ 720000 1200000
+ 528000 1100000
+ 312000 1000000
+ 144000 1000000
+ >;
+ #cooling-cells = <2>;
};
};
cooling-maps {
map0 {
trip = <&cpu_alert0>;
- cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+ cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
};
};
};
};
- memory {
- reg = <0x40000000 0x80000000>;
+ reserved-memory {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ /* Address must be kept in the lower 256 MiBs of DRAM for VE. */
+ default-pool {
+ compatible = "shared-dma-pool";
+ size = <0x6000000>;
+ alloc-ranges = <0x4a000000 0x6000000>;
+ reusable;
+ linux,cma-default;
+ };
};
timer {
};
pmu {
- compatible = "arm,cortex-a7-pmu", "arm,cortex-a15-pmu";
+ compatible = "arm,cortex-a7-pmu";
interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>;
};
#size-cells = <1>;
ranges;
- osc24M: clk@1c20050 {
+ osc24M: clk-24M {
#clock-cells = <0>;
compatible = "fixed-clock";
clock-frequency = <24000000>;
clock-output-names = "osc24M";
};
- osc32k: clk@0 {
+ osc32k: clk-32k {
#clock-cells = <0>;
compatible = "fixed-clock";
clock-frequency = <32768>;
* The actual TX clock rate is not controlled by the
* gmac_tx clock.
*/
- mii_phy_tx_clk: clk@1 {
+ mii_phy_tx_clk: clk-mii-phy-tx {
#clock-cells = <0>;
compatible = "fixed-clock";
clock-frequency = <25000000>;
clock-output-names = "mii_phy_tx";
};
- gmac_int_tx_clk: clk@2 {
+ gmac_int_tx_clk: clk-gmac-int-tx {
#clock-cells = <0>;
compatible = "fixed-clock";
clock-frequency = <125000000>;
status = "disabled";
};
- soc@1c00000 {
+ soc {
compatible = "simple-bus";
#address-cells = <1>;
#size-cells = <1>;
ranges;
- sram-controller@1c00000 {
- compatible = "allwinner,sun4i-a10-sram-controller";
+ system-control@1c00000 {
+ compatible = "allwinner,sun7i-a20-system-control",
+ "allwinner,sun4i-a10-system-control";
reg = <0x01c00000 0x30>;
#address-cells = <1>;
#size-cells = <1>;
ranges = <0 0x00000000 0xc000>;
emac_sram: sram-section@8000 {
- compatible = "allwinner,sun4i-a10-sram-a3-a4";
+ compatible = "allwinner,sun7i-a20-sram-a3-a4",
+ "allwinner,sun4i-a10-sram-a3-a4";
reg = <0x8000 0x4000>;
status = "disabled";
};
ranges = <0 0x00010000 0x1000>;
otg_sram: sram-section@0 {
- compatible = "allwinner,sun4i-a10-sram-d";
+ compatible = "allwinner,sun7i-a20-sram-d",
+ "allwinner,sun4i-a10-sram-d";
reg = <0x0000 0x1000>;
status = "disabled";
};
};
+
+ sram_c: sram@1d00000 {
+ compatible = "mmio-sram";
+ reg = <0x01d00000 0xd0000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x01d00000 0xd0000>;
+
+ ve_sram: sram-section@0 {
+ compatible = "allwinner,sun7i-a20-sram-c1",
+ "allwinner,sun4i-a10-sram-c1";
+ reg = <0x000000 0x80000>;
+ };
+ };
};
nmi_intc: interrupt-controller@1c00030 {
};
};
+ video-codec@1c0e000 {
+ compatible = "allwinner,sun7i-a20-video-engine";
+ reg = <0x01c0e000 0x1000>;
+ clocks = <&ccu CLK_AHB_VE>, <&ccu CLK_VE>,
+ <&ccu CLK_DRAM_VE>;
+ clock-names = "ahb", "mod", "ram";
+ resets = <&ccu RST_VE>;
+ interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>;
+ allwinner,sram = <&ve_sram 1>;
+ };
+
mmc0: mmc@1c0f000 {
compatible = "allwinner,sun7i-a20-mmc";
reg = <0x01c0f000 0x1000>;
"output",
"sample";
interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins>;
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
"output",
"sample";
interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc2_pins>;
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
"output",
"sample";
interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc3_pins>;
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
};
hdmi_out: port@1 {
- #address-cells = <1>;
- #size-cells = <0>;
reg = <1>;
};
};
#interrupt-cells = <3>;
#gpio-cells = <3>;
- can0_pins_a: can0@0 {
+ can_ph_pins: can-ph-pins {
pins = "PH20", "PH21";
function = "can";
};
- clk_out_a_pins_a: clk_out_a@0 {
+ clk_out_a_pin: clk-out-a-pin {
pins = "PI12";
function = "clk_out_a";
};
- clk_out_b_pins_a: clk_out_b@0 {
+ clk_out_b_pin: clk-out-b-pin {
pins = "PI13";
function = "clk_out_b";
};
- emac_pins_a: emac0@0 {
+ emac_pa_pins: emac-pa-pins {
pins = "PA0", "PA1", "PA2",
"PA3", "PA4", "PA5", "PA6",
"PA7", "PA8", "PA9", "PA10",
function = "emac";
};
- gmac_pins_mii_a: gmac_mii@0 {
+ gmac_mii_pins: gmac-mii-pins {
pins = "PA0", "PA1", "PA2",
"PA3", "PA4", "PA5", "PA6",
"PA7", "PA8", "PA9", "PA10",
function = "gmac";
};
- gmac_pins_rgmii_a: gmac_rgmii@0 {
+ gmac_rgmii_pins: gmac-rgmii-pins {
pins = "PA0", "PA1", "PA2",
"PA3", "PA4", "PA5", "PA6",
"PA7", "PA8", "PA10",
drive-strength = <40>;
};
- i2c0_pins_a: i2c0@0 {
+ i2c0_pins: i2c0-pins {
pins = "PB0", "PB1";
function = "i2c0";
};
- i2c1_pins_a: i2c1@0 {
+ i2c1_pins: i2c1-pins {
pins = "PB18", "PB19";
function = "i2c1";
};
- i2c2_pins_a: i2c2@0 {
+ i2c2_pins: i2c2-pins {
pins = "PB20", "PB21";
function = "i2c2";
};
- i2c3_pins_a: i2c3@0 {
+ i2c3_pins: i2c3-pins {
pins = "PI0", "PI1";
function = "i2c3";
};
- ir0_rx_pins_a: ir0@0 {
+ ir0_rx_pin: ir0-rx-pin {
pins = "PB4";
function = "ir0";
};
- ir0_tx_pins_a: ir0@1 {
+ ir0_tx_pin: ir0-tx-pin {
pins = "PB3";
function = "ir0";
};
- ir1_rx_pins_a: ir1@0 {
+ ir1_rx_pin: ir1-rx-pin {
pins = "PB23";
function = "ir1";
};
- ir1_tx_pins_a: ir1@1 {
+ ir1_tx_pin: ir1-tx-pin {
pins = "PB22";
function = "ir1";
};
- mmc0_pins_a: mmc0@0 {
+ mmc0_pins: mmc0-pins {
pins = "PF0", "PF1", "PF2",
"PF3", "PF4", "PF5";
function = "mmc0";
bias-pull-up;
};
- mmc2_pins_a: mmc2@0 {
+ mmc2_pins: mmc2-pins {
pins = "PC6", "PC7", "PC8",
"PC9", "PC10", "PC11";
function = "mmc2";
bias-pull-up;
};
- mmc3_pins_a: mmc3@0 {
+ mmc3_pins: mmc3-pins {
pins = "PI4", "PI5", "PI6",
"PI7", "PI8", "PI9";
function = "mmc3";
bias-pull-up;
};
- ps20_pins_a: ps20@0 {
+ ps2_0_pins: ps2-0-pins {
pins = "PI20", "PI21";
function = "ps2";
};
- ps21_pins_a: ps21@0 {
+ ps2_1_ph_pins: ps2-1-ph-pins {
pins = "PH12", "PH13";
function = "ps2";
};
- pwm0_pins_a: pwm0@0 {
+ pwm0_pin: pwm0-pin {
pins = "PB2";
function = "pwm";
};
- pwm1_pins_a: pwm1@0 {
+ pwm1_pin: pwm1-pin {
pins = "PI3";
function = "pwm";
};
- spdif_tx_pins_a: spdif@0 {
+ spdif_tx_pin: spdif-tx-pin {
pins = "PB13";
function = "spdif";
bias-pull-up;
};
- spi0_pins_a: spi0@0 {
+ spi0_pi_pins: spi0-pi-pins {
pins = "PI11", "PI12", "PI13";
function = "spi0";
};
- spi0_cs0_pins_a: spi0_cs0@0 {
+ spi0_cs0_pi_pin: spi0-cs0-pi-pin {
pins = "PI10";
function = "spi0";
};
- spi0_cs1_pins_a: spi0_cs1@0 {
+ spi0_cs1_pi_pin: spi0-cs1-pi-pin {
pins = "PI14";
function = "spi0";
};
- spi1_pins_a: spi1@0 {
+ spi1_pi_pins: spi1-pi-pins {
pins = "PI17", "PI18", "PI19";
function = "spi1";
};
- spi1_cs0_pins_a: spi1_cs0@0 {
+ spi1_cs0_pi_pin: spi1-cs0-pi-pin {
pins = "PI16";
function = "spi1";
};
- spi2_pins_a: spi2@0 {
- pins = "PC20", "PC21", "PC22";
+ spi2_pb_pins: spi2-pb-pins {
+ pins = "PB15", "PB16", "PB17";
function = "spi2";
};
- spi2_pins_b: spi2@1 {
- pins = "PB15", "PB16", "PB17";
+ spi2_cs0_pb_pin: spi2-cs0-pb-pin {
+ pins = "PB14";
function = "spi2";
};
- spi2_cs0_pins_a: spi2_cs0@0 {
- pins = "PC19";
+ spi2_pc_pins: spi2-pc-pins {
+ pins = "PC20", "PC21", "PC22";
function = "spi2";
};
- spi2_cs0_pins_b: spi2_cs0@1 {
- pins = "PB14";
+ spi2_cs0_pc_pin: spi2-cs0-pc-pin {
+ pins = "PC19";
function = "spi2";
};
- uart0_pins_a: uart0@0 {
+ uart0_pb_pins: uart0-pb-pins {
pins = "PB22", "PB23";
function = "uart0";
};
- uart2_pins_a: uart2@0 {
- pins = "PI16", "PI17", "PI18", "PI19";
+ uart2_pi_pins: uart2-pi-pins {
+ pins = "PI18", "PI19";
function = "uart2";
};
- uart3_pins_a: uart3@0 {
- pins = "PG6", "PG7", "PG8", "PG9";
+ uart2_cts_rts_pi_pins: uart2-cts-rts-pi-pins {
+ pins = "PI16", "PI17";
+ function = "uart2";
+ };
+
+ uart3_pg_pins: uart3-pg-pins {
+ pins = "PG6", "PG7";
+ function = "uart3";
+ };
+
+ uart3_cts_rts_pg_pins: uart3-cts-rts-pg-pins {
+ pins = "PG8", "PG9";
function = "uart3";
};
- uart3_pins_b: uart3@1 {
+ uart3_ph_pins: uart3-ph-pins {
pins = "PH0", "PH1";
function = "uart3";
};
- uart4_pins_a: uart4@0 {
+ uart4_pg_pins: uart4-pg-pins {
pins = "PG10", "PG11";
function = "uart4";
};
- uart4_pins_b: uart4@1 {
+ uart4_ph_pins: uart4-ph-pins {
pins = "PH4", "PH5";
function = "uart4";
};
- uart5_pins_a: uart5@0 {
+ uart5_pi_pins: uart5-pi-pins {
pins = "PI10", "PI11";
function = "uart5";
};
- uart6_pins_a: uart6@0 {
+ uart6_pi_pins: uart6-pi-pins {
pins = "PI12", "PI13";
function = "uart6";
};
- uart7_pins_a: uart7@0 {
+ uart7_pi_pins: uart7-pi-pins {
pins = "PI20", "PI21";
function = "uart7";
};
reg = <0x01c2ac00 0x400>;
interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&ccu CLK_APB1_I2C0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins>;
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
reg = <0x01c2b000 0x400>;
interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&ccu CLK_APB1_I2C1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_pins>;
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
reg = <0x01c2b400 0x400>;
interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&ccu CLK_APB1_I2C2>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c2_pins>;
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
reg = <0x01c2b800 0x400>;
interrupts = <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&ccu CLK_APB1_I2C3>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c3_pins>;
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
};
&i2c0 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins_a>;
status = "okay";
axp209: pmic@34 {
};
&i2c1 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c1_pins_a>;
status = "okay";
};
&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_a>;
+ pinctrl-0 = <&uart0_pb_pins>;
status = "okay";
};
projects / platform / kernel / u-boot.git / commitdiff