powerpc/fsl-booke: Add initial T1040/T1042 RDB board support

T1040/T1042RDB is Freescale Reference Design Board.
The board can support both T1040/T1042 QorIQ Power Architecture™ processor.

T1040/T1042RDB board Overview
-----------------------
- SERDES Connections, 8 lanes supporting:
	- PCI
	- SGMII
    	- QSGMII
    	- SATA 2.0
- DDR Controller
    	- Supports rates of up to 1600 MHz data-rate
    	- Supports one DDR3LP UDIMM
-IFC/Local Bus
    	- NAND flash: 1GB 8-bit NAND flash
    	- NOR: 128MB 16-bit NOR Flash
- Ethernet
    	- Two on-board RGMII 10/100/1G ethernet ports.
    	- PHY #0 remains powered up during deep-sleep
- CPLD
- Clocks
    	- System and DDR clock (SYSCLK, “DDRCLK”)
    	- SERDES clocks
- Power Supplies
- USB
    	- Supports two USB 2.0 ports with integrated PHYs
    	- Two type A ports with 5V@1.5A per port.
- SDHC
    	- SDHC/SDXC connector
- SPI
    	- On-board 64MB SPI flash
- I2C
    	- Devices connected: EEPROM, thermal monitor, VID controller
- Other IO
    	- Two Serial ports
    	- ProfiBus port

Add support for T1040/T1042 RDB board:
    -add device tree
    -add entry in Kconfig to build
    -Add entry in corenet_generic.c, as it is similar to other corenet platforms

Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>

diff --git a/arch/powerpc/boot/dts/t1040rdb.dts b/arch/powerpc/boot/dts/t1040rdb.dts
new file mode 100644 (file)
index 0000000..79a0bed
--- /dev/null
+++ b/arch/powerpc/boot/dts/t1040rdb.dts
@@ -0,0 +1,48 @@
+/*
+ * T1040RDB Device Tree Source
+ *
+ * Copyright 2014 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ *     * Redistributions of source code must retain the above copyright
+ *      notice, this list of conditions and the following disclaimer.
+ *     * Redistributions in binary form must reproduce the above copyright
+ *      notice, this list of conditions and the following disclaimer in the
+ *      documentation and/or other materials provided with the distribution.
+ *     * Neither the name of Freescale Semiconductor nor the
+ *      names of its contributors may be used to endorse or promote products
+ *      derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor "AS IS" AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/include/ "fsl/t104xsi-pre.dtsi"
+/include/ "t104xrdb.dtsi"
+
+/ {
+       model = "fsl,T1040RDB";
+       compatible = "fsl,T1040RDB";
+       ifc: localbus@ffe124000 {
+               cpld@3,0 {
+                       compatible = "fsl,t1040rdb-cpld";
+               };
+       };
+};
+
+/include/ "fsl/t1040si-post.dtsi"

diff --git a/arch/powerpc/boot/dts/t1042rdb.dts b/arch/powerpc/boot/dts/t1042rdb.dts
new file mode 100644 (file)
index 0000000..738c237
--- /dev/null
+++ b/arch/powerpc/boot/dts/t1042rdb.dts
@@ -0,0 +1,48 @@
+/*
+ * T1042RDB Device Tree Source
+ *
+ * Copyright 2014 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ *     * Redistributions of source code must retain the above copyright
+ *      notice, this list of conditions and the following disclaimer.
+ *     * Redistributions in binary form must reproduce the above copyright
+ *      notice, this list of conditions and the following disclaimer in the
+ *      documentation and/or other materials provided with the distribution.
+ *     * Neither the name of Freescale Semiconductor nor the
+ *      names of its contributors may be used to endorse or promote products
+ *      derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor "AS IS" AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/include/ "fsl/t104xsi-pre.dtsi"
+/include/ "t104xrdb.dtsi"
+
+/ {
+       model = "fsl,T1042RDB";
+       compatible = "fsl,T1042RDB";
+       ifc: localbus@ffe124000 {
+               cpld@3,0 {
+                       compatible = "fsl,t1042rdb-cpld";
+               };
+       };
+};
+
+/include/ "fsl/t1042si-post.dtsi"

diff --git a/arch/powerpc/boot/dts/t104xrdb.dtsi b/arch/powerpc/boot/dts/t104xrdb.dtsi
new file mode 100644 (file)
index 0000000..1cf0f3c
--- /dev/null
+++ b/arch/powerpc/boot/dts/t104xrdb.dtsi
@@ -0,0 +1,156 @@
+/*
+ * T1040RDB/T1042RDB Device Tree Source
+ *
+ * Copyright 2014 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ *     * Redistributions of source code must retain the above copyright
+ *      notice, this list of conditions and the following disclaimer.
+ *     * Redistributions in binary form must reproduce the above copyright
+ *      notice, this list of conditions and the following disclaimer in the
+ *      documentation and/or other materials provided with the distribution.
+ *     * Neither the name of Freescale Semiconductor nor the
+ *      names of its contributors may be used to endorse or promote products
+ *      derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor "AS IS" AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/ {
+
+       ifc: localbus@ffe124000 {
+               reg = <0xf 0xfe124000 0 0x2000>;
+               ranges = <0 0 0xf 0xe8000000 0x08000000
+                         2 0 0xf 0xff800000 0x00010000
+                         3 0 0xf 0xffdf0000 0x00008000>;
+
+               nor@0,0 {
+                       #address-cells = <1>;
+                       #size-cells = <1>;
+                       compatible = "cfi-flash";
+                       reg = <0x0 0x0 0x8000000>;
+                       bank-width = <2>;
+                       device-width = <1>;
+               };
+
+               nand@2,0 {
+                       #address-cells = <1>;
+                       #size-cells = <1>;
+                       compatible = "fsl,ifc-nand";
+                       reg = <0x2 0x0 0x10000>;
+               };
+
+               cpld@3,0 {
+                       reg = <3 0 0x300>;
+               };
+       };
+
+       memory {
+               device_type = "memory";
+       };
+
+       dcsr: dcsr@f00000000 {
+               ranges = <0x00000000 0xf 0x00000000 0x01072000>;
+       };
+
+       soc: soc@ffe000000 {
+               ranges = <0x00000000 0xf 0xfe000000 0x1000000>;
+               reg = <0xf 0xfe000000 0 0x00001000>;
+
+               spi@110000 {
+                       flash@0 {
+                               #address-cells = <1>;
+                               #size-cells = <1>;
+                               compatible = "micron,n25q512a";
+                               reg = <0>;
+                               spi-max-frequency = <10000000>; /* input clock */
+                       };
+               };
+
+               i2c@118100 {
+                       pca9546@77 {
+                               compatible = "nxp,pca9546";
+                               reg = <0x77>;
+                               #address-cells = <1>;
+                               #size-cells = <0>;
+                       };
+               };
+
+       };
+
+       pci0: pcie@ffe240000 {
+               reg = <0xf 0xfe240000 0 0x10000>;
+               ranges = <0x02000000 0 0xe0000000 0xc 0x00000000 0x0 0x10000000
+                         0x01000000 0 0x00000000 0xf 0xf8000000 0x0 0x00010000>;
+               pcie@0 {
+                       ranges = <0x02000000 0 0xe0000000
+                                 0x02000000 0 0xe0000000
+                                 0 0x10000000
+
+                                 0x01000000 0 0x00000000
+                                 0x01000000 0 0x00000000
+                                 0 0x00010000>;
+               };
+       };
+
+       pci1: pcie@ffe250000 {
+               reg = <0xf 0xfe250000 0 0x10000>;
+               ranges = <0x02000000 0x0 0xe0000000 0xc 0x10000000 0x0 0x10000000
+                         0x01000000 0x0 0x00000000 0xf 0xf8010000 0x0 0x00010000>;
+               pcie@0 {
+                       ranges = <0x02000000 0 0xe0000000
+                                 0x02000000 0 0xe0000000
+                                 0 0x10000000
+
+                                 0x01000000 0 0x00000000
+                                 0x01000000 0 0x00000000
+                                 0 0x00010000>;
+               };
+       };
+
+       pci2: pcie@ffe260000 {
+               reg = <0xf 0xfe260000 0 0x10000>;
+               ranges = <0x02000000 0 0xe0000000 0xc 0x20000000 0 0x10000000
+                         0x01000000 0 0x00000000 0xf 0xf8020000 0 0x00010000>;
+               pcie@0 {
+                       ranges = <0x02000000 0 0xe0000000
+                                 0x02000000 0 0xe0000000
+                                 0 0x10000000
+
+                                 0x01000000 0 0x00000000
+                                 0x01000000 0 0x00000000
+                                 0 0x00010000>;
+               };
+       };
+
+       pci3: pcie@ffe270000 {
+               reg = <0xf 0xfe270000 0 0x10000>;
+               ranges = <0x02000000 0 0xe0000000 0xc 0x30000000 0 0x10000000
+                         0x01000000 0 0x00000000 0xf 0xf8030000 0 0x00010000>;
+               pcie@0 {
+                       ranges = <0x02000000 0 0xe0000000
+                                 0x02000000 0 0xe0000000
+                                 0 0x10000000
+
+                                 0x01000000 0 0x00000000
+                                 0x01000000 0 0x00000000
+                                 0 0x00010000>;
+               };
+       };
+};

diff --git a/arch/powerpc/platforms/85xx/Kconfig b/arch/powerpc/platforms/85xx/Kconfig
index 0c1e690..f22635a 100644 (file)
--- a/arch/powerpc/platforms/85xx/Kconfig
+++ b/arch/powerpc/platforms/85xx/Kconfig
@@ -276,7 +276,7 @@ config CORENET_GENERIC
          For 64bit kernel, the following boards are supported:
            T208x QDS/RDB, T4240 QDS/RDB and B4 QDS
          The following boards are supported for both 32bit and 64bit kernel:
-           P5020 DS, P5040 DS and T104xQDS
+           P5020 DS, P5040 DS and T104xQDS/RDB
 
 endif # FSL_SOC_BOOKE
 

diff --git a/arch/powerpc/platforms/85xx/corenet_generic.c b/arch/powerpc/platforms/85xx/corenet_generic.c
index c2adb00..cc28978 100644 (file)
--- a/arch/powerpc/platforms/85xx/corenet_generic.c
+++ b/arch/powerpc/platforms/85xx/corenet_generic.c
@@ -140,6 +140,8 @@ static const char * const boards[] __initconst = {
        "fsl,B4220QDS",
        "fsl,T1040QDS",
        "fsl,T1042QDS",
+       "fsl,T1040RDB",
+       "fsl,T1042RDB",
        "keymile,kmcoge4",
        NULL
 };