spi: atmel: Remove nondm code
authorJagan Teki <jagan@amarulasolutions.com>
Wed, 27 May 2020 17:29:12 +0000 (22:59 +0530)
committerJagan Teki <jagan@amarulasolutions.com>
Thu, 11 Jun 2020 09:44:04 +0000 (15:14 +0530)
atmel spi driver now accessible only when DM_SPI enabled.

So, remove nondm code.

Cc: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
drivers/spi/atmel_spi.c
drivers/spi/atmel_spi.h

index f076e92..b9f684d 100644 (file)
 
 #include <asm/arch/clk.h>
 #include <asm/arch/hardware.h>
-#ifdef CONFIG_DM_SPI
 #include <asm/arch/at91_spi.h>
-#endif
 #if CONFIG_IS_ENABLED(DM_GPIO)
 #include <asm/gpio.h>
 #endif
 
 #include "atmel_spi.h"
 
-#ifndef CONFIG_DM_SPI
-
-static int spi_has_wdrbt(struct atmel_spi_slave *slave)
-{
-       unsigned int ver;
-
-       ver = spi_readl(slave, VERSION);
-
-       return (ATMEL_SPI_VERSION_REV(ver) >= 0x210);
-}
-
-struct spi_slave *spi_setup_slave(unsigned int bus, unsigned int cs,
-                       unsigned int max_hz, unsigned int mode)
-{
-       struct atmel_spi_slave  *as;
-       unsigned int            scbr;
-       u32                     csrx;
-       void                    *regs;
-
-       if (!spi_cs_is_valid(bus, cs))
-               return NULL;
-
-       switch (bus) {
-       case 0:
-               regs = (void *)ATMEL_BASE_SPI0;
-               break;
-#ifdef ATMEL_BASE_SPI1
-       case 1:
-               regs = (void *)ATMEL_BASE_SPI1;
-               break;
-#endif
-#ifdef ATMEL_BASE_SPI2
-       case 2:
-               regs = (void *)ATMEL_BASE_SPI2;
-               break;
-#endif
-#ifdef ATMEL_BASE_SPI3
-       case 3:
-               regs = (void *)ATMEL_BASE_SPI3;
-               break;
-#endif
-       default:
-               return NULL;
-       }
-
-
-       scbr = (get_spi_clk_rate(bus) + max_hz - 1) / max_hz;
-       if (scbr > ATMEL_SPI_CSRx_SCBR_MAX)
-               /* Too low max SCK rate */
-               return NULL;
-       if (scbr < 1)
-               scbr = 1;
-
-       csrx = ATMEL_SPI_CSRx_SCBR(scbr);
-       csrx |= ATMEL_SPI_CSRx_BITS(ATMEL_SPI_BITS_8);
-       if (!(mode & SPI_CPHA))
-               csrx |= ATMEL_SPI_CSRx_NCPHA;
-       if (mode & SPI_CPOL)
-               csrx |= ATMEL_SPI_CSRx_CPOL;
-
-       as = spi_alloc_slave(struct atmel_spi_slave, bus, cs);
-       if (!as)
-               return NULL;
-
-       as->regs = regs;
-       as->mr = ATMEL_SPI_MR_MSTR | ATMEL_SPI_MR_MODFDIS
-                       | ATMEL_SPI_MR_PCS(~(1 << cs) & 0xf);
-       if (spi_has_wdrbt(as))
-               as->mr |= ATMEL_SPI_MR_WDRBT;
-
-       spi_writel(as, CSR(cs), csrx);
-
-       return &as->slave;
-}
-
-void spi_free_slave(struct spi_slave *slave)
-{
-       struct atmel_spi_slave *as = to_atmel_spi(slave);
-
-       free(as);
-}
-
-int spi_claim_bus(struct spi_slave *slave)
-{
-       struct atmel_spi_slave *as = to_atmel_spi(slave);
-
-       /* Enable the SPI hardware */
-       spi_writel(as, CR, ATMEL_SPI_CR_SPIEN);
-
-       /*
-        * Select the slave. This should set SCK to the correct
-        * initial state, etc.
-        */
-       spi_writel(as, MR, as->mr);
-
-       return 0;
-}
-
-void spi_release_bus(struct spi_slave *slave)
-{
-       struct atmel_spi_slave *as = to_atmel_spi(slave);
-
-       /* Disable the SPI hardware */
-       spi_writel(as, CR, ATMEL_SPI_CR_SPIDIS);
-}
-
-int spi_xfer(struct spi_slave *slave, unsigned int bitlen,
-               const void *dout, void *din, unsigned long flags)
-{
-       struct atmel_spi_slave *as = to_atmel_spi(slave);
-       unsigned int    len_tx;
-       unsigned int    len_rx;
-       unsigned int    len;
-       u32             status;
-       const u8        *txp = dout;
-       u8              *rxp = din;
-       u8              value;
-
-       if (bitlen == 0)
-               /* Finish any previously submitted transfers */
-               goto out;
-
-       /*
-        * TODO: The controller can do non-multiple-of-8 bit
-        * transfers, but this driver currently doesn't support it.
-        *
-        * It's also not clear how such transfers are supposed to be
-        * represented as a stream of bytes...this is a limitation of
-        * the current SPI interface.
-        */
-       if (bitlen % 8) {
-               /* Errors always terminate an ongoing transfer */
-               flags |= SPI_XFER_END;
-               goto out;
-       }
-
-       len = bitlen / 8;
-
-       /*
-        * The controller can do automatic CS control, but it is
-        * somewhat quirky, and it doesn't really buy us much anyway
-        * in the context of U-Boot.
-        */
-       if (flags & SPI_XFER_BEGIN) {
-               spi_cs_activate(slave);
-               /*
-                * sometimes the RDR is not empty when we get here,
-                * in theory that should not happen, but it DOES happen.
-                * Read it here to be on the safe side.
-                * That also clears the OVRES flag. Required if the
-                * following loop exits due to OVRES!
-                */
-               spi_readl(as, RDR);
-       }
-
-       for (len_tx = 0, len_rx = 0; len_rx < len; ) {
-               status = spi_readl(as, SR);
-
-               if (status & ATMEL_SPI_SR_OVRES)
-                       return -1;
-
-               if (len_tx < len && (status & ATMEL_SPI_SR_TDRE)) {
-                       if (txp)
-                               value = *txp++;
-                       else
-                               value = 0;
-                       spi_writel(as, TDR, value);
-                       len_tx++;
-               }
-               if (status & ATMEL_SPI_SR_RDRF) {
-                       value = spi_readl(as, RDR);
-                       if (rxp)
-                               *rxp++ = value;
-                       len_rx++;
-               }
-       }
-
-out:
-       if (flags & SPI_XFER_END) {
-               /*
-                * Wait until the transfer is completely done before
-                * we deactivate CS.
-                */
-               do {
-                       status = spi_readl(as, SR);
-               } while (!(status & ATMEL_SPI_SR_TXEMPTY));
-
-               spi_cs_deactivate(slave);
-       }
-
-       return 0;
-}
-
-#else
-
 #define MAX_CS_COUNT   4
 
 struct atmel_spi_platdata {
@@ -507,4 +310,3 @@ U_BOOT_DRIVER(atmel_spi) = {
        .priv_auto_alloc_size = sizeof(struct atmel_spi_priv),
        .probe  = atmel_spi_probe,
 };
-#endif
index b602887..9663cca 100644 (file)
 #define ATMEL_SPI_BITS_15              7
 #define ATMEL_SPI_BITS_16              8
 
-struct atmel_spi_slave {
-       struct spi_slave slave;
-       void            *regs;
-       u32             mr;
-};
-
-static inline struct atmel_spi_slave *to_atmel_spi(struct spi_slave *slave)
-{
-       return container_of(slave, struct atmel_spi_slave, slave);
-}
-
 /* Register access macros */
 #define spi_readl(as, reg)                                     \
        readl(as->regs + ATMEL_SPI_##reg)