- compatible : should be "samsung,exynos5250-dp-video-phy";
- reg : offset and length of the Display Port PHY register set;
- #phy-cells : from the generic PHY bindings, must be 0;
+
+Samsung S5P/EXYNOS SoC series USB PHY
+-------------------------------------------------
+
+Required properties:
+- compatible : should be one of the listed compatibles:
+ - "samsung,exynos4210-usb2-phy"
+ - "samsung,exynos4x12-usb2-phy"
+- reg : a list of registers used by phy driver
+ - first and obligatory is the location of phy modules registers
+- samsung,sysreg-phandle - handle to syscon used to control the system registers
+- samsung,pmureg-phandle - handle to syscon used to control PMU registers
+- #phy-cells : from the generic phy bindings, must be 1;
+- clocks and clock-names:
+ - the "phy" clock is required by the phy module, used as a gate
+ - the "ref" clock is used to get the rate of the clock provided to the
+ PHY module
+
+The first phandle argument in the PHY specifier identifies the PHY, its
+meaning is compatible dependent. For the currently supported SoCs (Exynos 4210
+and Exynos 4212) it is as follows:
+ 0 - USB device ("device"),
+ 1 - USB host ("host"),
+ 2 - HSIC0 ("hsic0"),
+ 3 - HSIC1 ("hsic1"),
+
+Exynos 4210 and Exynos 4212 use mode switching and require that mode switch
+register is supplied.
+
+Example:
+
+For Exynos 4412 (compatible with Exynos 4212):
+
+usbphy: phy@125b0000 {
+ compatible = "samsung,exynos4x12-usb2-phy";
+ reg = <0x125b0000 0x100>;
+ clocks = <&clock 305>, <&clock 2>;
+ clock-names = "phy", "ref";
+ status = "okay";
+ #phy-cells = <1>;
+ samsung,sysreg-phandle = <&sys_reg>;
+ samsung,pmureg-phandle = <&pmu_reg>;
+};
+
+Then the PHY can be used in other nodes such as:
+
+phy-consumer@12340000 {
+ phys = <&usbphy 2>;
+ phy-names = "phy";
+};
+
+Refer to DT bindings documentation of particular PHY consumer devices for more
+information about required PHYs and the way of specification.
--- /dev/null
+.------------------------------------------------------------------------------+
+| Samsung USB 2.0 PHY adaptation layer |
++-----------------------------------------------------------------------------+'
+
+| 1. Description
++----------------
+
+The architecture of the USB 2.0 PHY module in Samsung SoCs is similar
+among many SoCs. In spite of the similarities it proved difficult to
+create a one driver that would fit all these PHY controllers. Often
+the differences were minor and were found in particular bits of the
+registers of the PHY. In some rare cases the order of register writes or
+the PHY powering up process had to be altered. This adaptation layer is
+a compromise between having separate drivers and having a single driver
+with added support for many special cases.
+
+| 2. Files description
++----------------------
+
+- phy-samsung-usb2.c
+ This is the main file of the adaptation layer. This file contains
+ the probe function and provides two callbacks to the Generic PHY
+ Framework. This two callbacks are used to power on and power off the
+ phy. They carry out the common work that has to be done on all version
+ of the PHY module. Depending on which SoC was chosen they execute SoC
+ specific callbacks. The specific SoC version is selected by choosing
+ the appropriate compatible string. In addition, this file contains
+ struct of_device_id definitions for particular SoCs.
+
+- phy-samsung-usb2.h
+ This is the include file. It declares the structures used by this
+ driver. In addition it should contain extern declarations for
+ structures that describe particular SoCs.
+
+| 3. Supporting SoCs
++--------------------
+
+To support a new SoC a new file should be added to the drivers/phy
+directory. Each SoC's configuration is stored in an instance of the
+struct samsung_usb2_phy_config.
+
+struct samsung_usb2_phy_config {
+ const struct samsung_usb2_common_phy *phys;
+ int (*rate_to_clk)(unsigned long, u32 *);
+ unsigned int num_phys;
+ bool has_mode_switch;
+};
+
+The num_phys is the number of phys handled by the driver. *phys is an
+array that contains the configuration for each phy. The has_mode_switch
+property is a boolean flag that determines whether the SoC has USB host
+and device on a single pair of pins. If so, a special register has to
+be modified to change the internal routing of these pins between a USB
+device or host module.
+
+For example the configuration for Exynos 4210 is following:
+
+const struct samsung_usb2_phy_config exynos4210_usb2_phy_config = {
+ .has_mode_switch = 0,
+ .num_phys = EXYNOS4210_NUM_PHYS,
+ .phys = exynos4210_phys,
+ .rate_to_clk = exynos4210_rate_to_clk,
+}
+
+- int (*rate_to_clk)(unsigned long, u32 *)
+ The rate_to_clk callback is to convert the rate of the clock
+ used as the reference clock for the PHY module to the value
+ that should be written in the hardware register.
+
+The exynos4210_phys configuration array is as follows:
+
+static const struct samsung_usb2_common_phy exynos4210_phys[] = {
+ {
+ .label = "device",
+ .id = EXYNOS4210_DEVICE,
+ .power_on = exynos4210_power_on,
+ .power_off = exynos4210_power_off,
+ },
+ {
+ .label = "host",
+ .id = EXYNOS4210_HOST,
+ .power_on = exynos4210_power_on,
+ .power_off = exynos4210_power_off,
+ },
+ {
+ .label = "hsic0",
+ .id = EXYNOS4210_HSIC0,
+ .power_on = exynos4210_power_on,
+ .power_off = exynos4210_power_off,
+ },
+ {
+ .label = "hsic1",
+ .id = EXYNOS4210_HSIC1,
+ .power_on = exynos4210_power_on,
+ .power_off = exynos4210_power_off,
+ },
+ {},
+};
+
+- int (*power_on)(struct samsung_usb2_phy_instance *);
+- int (*power_off)(struct samsung_usb2_phy_instance *);
+ These two callbacks are used to power on and power off the phy
+ by modifying appropriate registers.
+
+Final change to the driver is adding appropriate compatible value to the
+phy-samsung-usb2.c file. In case of Exynos 4210 the following lines were
+added to the struct of_device_id samsung_usb2_phy_of_match[] array:
+
+#ifdef CONFIG_PHY_EXYNOS4210_USB2
+ {
+ .compatible = "samsung,exynos4210-usb2-phy",
+ .data = &exynos4210_usb2_phy_config,
+ },
+#endif
+
+To add further flexibility to the driver the Kconfig file enables to
+include support for selected SoCs in the compiled driver. The Kconfig
+entry for Exynos 4210 is following:
+
+config PHY_EXYNOS4210_USB2
+ bool "Support for Exynos 4210"
+ depends on PHY_SAMSUNG_USB2
+ depends on CPU_EXYNOS4210
+ help
+ Enable USB PHY support for Exynos 4210. This option requires that
+ Samsung USB 2.0 PHY driver is enabled and means that support for this
+ particular SoC is compiled in the driver. In case of Exynos 4210 four
+ phys are available - device, host, HSCI0 and HSCI1.
+
+The newly created file that supports the new SoC has to be also added to the
+Makefile. In case of Exynos 4210 the added line is following:
+
+obj-$(CONFIG_PHY_EXYNOS4210_USB2) += phy-exynos4210-usb2.o
+
+After completing these steps the support for the new SoC should be ready.
This driver controls the entire USB PHY block, both the USB OTG
parts, as well as the 2 regular USB 2 host PHYs.
+config PHY_SAMSUNG_USB2
+ tristate "Samsung USB 2.0 PHY driver"
+ select GENERIC_PHY
+ select MFD_SYSCON
+ help
+ Enable this to support the Samsung USB 2.0 PHY driver for Samsung
+ SoCs. This driver provides the interface for USB 2.0 PHY. Support for
+ particular SoCs has to be enabled in addition to this driver. Number
+ and type of supported phys depends on the SoC.
+
+config PHY_EXYNOS4210_USB2
+ bool "Support for Exynos 4210"
+ depends on PHY_SAMSUNG_USB2
+ depends on CPU_EXYNOS4210
+ help
+ Enable USB PHY support for Exynos 4210. This option requires that
+ Samsung USB 2.0 PHY driver is enabled and means that support for this
+ particular SoC is compiled in the driver. In case of Exynos 4210 four
+ phys are available - device, host, HSIC0 and HSIC1.
+
+config PHY_EXYNOS4X12_USB2
+ bool "Support for Exynos 4x12"
+ depends on PHY_SAMSUNG_USB2
+ depends on (SOC_EXYNOS4212 || SOC_EXYNOS4412)
+ help
+ Enable USB PHY support for Exynos 4x12. This option requires that
+ Samsung USB 2.0 PHY driver is enabled and means that support for this
+ particular SoC is compiled in the driver. In case of Exynos 4x12 four
+ phys are available - device, host, HSIC0 and HSIC1.
endmenu
obj-$(CONFIG_TWL4030_USB) += phy-twl4030-usb.o
obj-$(CONFIG_PHY_EXYNOS5250_SATA) += phy-exynos5250-sata.o
obj-$(CONFIG_PHY_SUN4I_USB) += phy-sun4i-usb.o
+obj-$(CONFIG_PHY_SAMSUNG_USB2) += phy-samsung-usb2.o
+obj-$(CONFIG_PHY_EXYNOS4210_USB2) += phy-exynos4210-usb2.o
+obj-$(CONFIG_PHY_EXYNOS4X12_USB2) += phy-exynos4x12-usb2.o
--- /dev/null
+/*
+ * Samsung SoC USB 1.1/2.0 PHY driver - Exynos 4210 support
+ *
+ * Copyright (C) 2013 Samsung Electronics Co., Ltd.
+ * Author: Kamil Debski <k.debski@samsung.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/delay.h>
+#include <linux/io.h>
+#include <linux/phy/phy.h>
+#include <linux/regmap.h>
+#include "phy-samsung-usb2.h"
+
+/* Exynos USB PHY registers */
+
+/* PHY power control */
+#define EXYNOS_4210_UPHYPWR 0x0
+
+#define EXYNOS_4210_UPHYPWR_PHY0_SUSPEND BIT(0)
+#define EXYNOS_4210_UPHYPWR_PHY0_PWR BIT(3)
+#define EXYNOS_4210_UPHYPWR_PHY0_OTG_PWR BIT(4)
+#define EXYNOS_4210_UPHYPWR_PHY0_SLEEP BIT(5)
+#define EXYNOS_4210_UPHYPWR_PHY0 ( \
+ EXYNOS_4210_UPHYPWR_PHY0_SUSPEND | \
+ EXYNOS_4210_UPHYPWR_PHY0_PWR | \
+ EXYNOS_4210_UPHYPWR_PHY0_OTG_PWR | \
+ EXYNOS_4210_UPHYPWR_PHY0_SLEEP)
+
+#define EXYNOS_4210_UPHYPWR_PHY1_SUSPEND BIT(6)
+#define EXYNOS_4210_UPHYPWR_PHY1_PWR BIT(7)
+#define EXYNOS_4210_UPHYPWR_PHY1_SLEEP BIT(8)
+#define EXYNOS_4210_UPHYPWR_PHY1 ( \
+ EXYNOS_4210_UPHYPWR_PHY1_SUSPEND | \
+ EXYNOS_4210_UPHYPWR_PHY1_PWR | \
+ EXYNOS_4210_UPHYPWR_PHY1_SLEEP)
+
+#define EXYNOS_4210_UPHYPWR_HSIC0_SUSPEND BIT(9)
+#define EXYNOS_4210_UPHYPWR_HSIC0_SLEEP BIT(10)
+#define EXYNOS_4210_UPHYPWR_HSIC0 ( \
+ EXYNOS_4210_UPHYPWR_HSIC0_SUSPEND | \
+ EXYNOS_4210_UPHYPWR_HSIC0_SLEEP)
+
+#define EXYNOS_4210_UPHYPWR_HSIC1_SUSPEND BIT(11)
+#define EXYNOS_4210_UPHYPWR_HSIC1_SLEEP BIT(12)
+#define EXYNOS_4210_UPHYPWR_HSIC1 ( \
+ EXYNOS_4210_UPHYPWR_HSIC1_SUSPEND | \
+ EXYNOS_4210_UPHYPWR_HSIC1_SLEEP)
+
+/* PHY clock control */
+#define EXYNOS_4210_UPHYCLK 0x4
+
+#define EXYNOS_4210_UPHYCLK_PHYFSEL_MASK (0x3 << 0)
+#define EXYNOS_4210_UPHYCLK_PHYFSEL_OFFSET 0
+#define EXYNOS_4210_UPHYCLK_PHYFSEL_48MHZ (0x0 << 0)
+#define EXYNOS_4210_UPHYCLK_PHYFSEL_24MHZ (0x3 << 0)
+#define EXYNOS_4210_UPHYCLK_PHYFSEL_12MHZ (0x2 << 0)
+
+#define EXYNOS_4210_UPHYCLK_PHY0_ID_PULLUP BIT(2)
+#define EXYNOS_4210_UPHYCLK_PHY0_COMMON_ON BIT(4)
+#define EXYNOS_4210_UPHYCLK_PHY1_COMMON_ON BIT(7)
+
+/* PHY reset control */
+#define EXYNOS_4210_UPHYRST 0x8
+
+#define EXYNOS_4210_URSTCON_PHY0 BIT(0)
+#define EXYNOS_4210_URSTCON_OTG_HLINK BIT(1)
+#define EXYNOS_4210_URSTCON_OTG_PHYLINK BIT(2)
+#define EXYNOS_4210_URSTCON_PHY1_ALL BIT(3)
+#define EXYNOS_4210_URSTCON_PHY1_P0 BIT(4)
+#define EXYNOS_4210_URSTCON_PHY1_P1P2 BIT(5)
+#define EXYNOS_4210_URSTCON_HOST_LINK_ALL BIT(6)
+#define EXYNOS_4210_URSTCON_HOST_LINK_P0 BIT(7)
+#define EXYNOS_4210_URSTCON_HOST_LINK_P1 BIT(8)
+#define EXYNOS_4210_URSTCON_HOST_LINK_P2 BIT(9)
+
+/* Isolation, configured in the power management unit */
+#define EXYNOS_4210_USB_ISOL_DEVICE_OFFSET 0x704
+#define EXYNOS_4210_USB_ISOL_DEVICE BIT(0)
+#define EXYNOS_4210_USB_ISOL_HOST_OFFSET 0x708
+#define EXYNOS_4210_USB_ISOL_HOST BIT(0)
+
+/* USBYPHY1 Floating prevention */
+#define EXYNOS_4210_UPHY1CON 0x34
+#define EXYNOS_4210_UPHY1CON_FLOAT_PREVENTION 0x1
+
+/* Mode switching SUB Device <-> Host */
+#define EXYNOS_4210_MODE_SWITCH_OFFSET 0x21c
+#define EXYNOS_4210_MODE_SWITCH_MASK 1
+#define EXYNOS_4210_MODE_SWITCH_DEVICE 0
+#define EXYNOS_4210_MODE_SWITCH_HOST 1
+
+enum exynos4210_phy_id {
+ EXYNOS4210_DEVICE,
+ EXYNOS4210_HOST,
+ EXYNOS4210_HSIC0,
+ EXYNOS4210_HSIC1,
+ EXYNOS4210_NUM_PHYS,
+};
+
+/*
+ * exynos4210_rate_to_clk() converts the supplied clock rate to the value that
+ * can be written to the phy register.
+ */
+static int exynos4210_rate_to_clk(unsigned long rate, u32 *reg)
+{
+ switch (rate) {
+ case 12 * MHZ:
+ *reg = EXYNOS_4210_UPHYCLK_PHYFSEL_12MHZ;
+ break;
+ case 24 * MHZ:
+ *reg = EXYNOS_4210_UPHYCLK_PHYFSEL_24MHZ;
+ break;
+ case 48 * MHZ:
+ *reg = EXYNOS_4210_UPHYCLK_PHYFSEL_48MHZ;
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
+static void exynos4210_isol(struct samsung_usb2_phy_instance *inst, bool on)
+{
+ struct samsung_usb2_phy_driver *drv = inst->drv;
+ u32 offset;
+ u32 mask;
+
+ switch (inst->cfg->id) {
+ case EXYNOS4210_DEVICE:
+ offset = EXYNOS_4210_USB_ISOL_DEVICE_OFFSET;
+ mask = EXYNOS_4210_USB_ISOL_DEVICE;
+ break;
+ case EXYNOS4210_HOST:
+ offset = EXYNOS_4210_USB_ISOL_HOST_OFFSET;
+ mask = EXYNOS_4210_USB_ISOL_HOST;
+ break;
+ default:
+ return;
+ };
+
+ regmap_update_bits(drv->reg_pmu, offset, mask, on ? 0 : mask);
+}
+
+static void exynos4210_phy_pwr(struct samsung_usb2_phy_instance *inst, bool on)
+{
+ struct samsung_usb2_phy_driver *drv = inst->drv;
+ u32 rstbits = 0;
+ u32 phypwr = 0;
+ u32 rst;
+ u32 pwr;
+ u32 clk;
+
+ switch (inst->cfg->id) {
+ case EXYNOS4210_DEVICE:
+ phypwr = EXYNOS_4210_UPHYPWR_PHY0;
+ rstbits = EXYNOS_4210_URSTCON_PHY0;
+ break;
+ case EXYNOS4210_HOST:
+ phypwr = EXYNOS_4210_UPHYPWR_PHY1;
+ rstbits = EXYNOS_4210_URSTCON_PHY1_ALL |
+ EXYNOS_4210_URSTCON_PHY1_P0 |
+ EXYNOS_4210_URSTCON_PHY1_P1P2 |
+ EXYNOS_4210_URSTCON_HOST_LINK_ALL |
+ EXYNOS_4210_URSTCON_HOST_LINK_P0;
+ writel(on, drv->reg_phy + EXYNOS_4210_UPHY1CON);
+ break;
+ case EXYNOS4210_HSIC0:
+ phypwr = EXYNOS_4210_UPHYPWR_HSIC0;
+ rstbits = EXYNOS_4210_URSTCON_PHY1_P1P2 |
+ EXYNOS_4210_URSTCON_HOST_LINK_P1;
+ break;
+ case EXYNOS4210_HSIC1:
+ phypwr = EXYNOS_4210_UPHYPWR_HSIC1;
+ rstbits = EXYNOS_4210_URSTCON_PHY1_P1P2 |
+ EXYNOS_4210_URSTCON_HOST_LINK_P2;
+ break;
+ };
+
+ if (on) {
+ clk = readl(drv->reg_phy + EXYNOS_4210_UPHYCLK);
+ clk &= ~EXYNOS_4210_UPHYCLK_PHYFSEL_MASK;
+ clk |= drv->ref_reg_val << EXYNOS_4210_UPHYCLK_PHYFSEL_OFFSET;
+ writel(clk, drv->reg_phy + EXYNOS_4210_UPHYCLK);
+
+ pwr = readl(drv->reg_phy + EXYNOS_4210_UPHYPWR);
+ pwr &= ~phypwr;
+ writel(pwr, drv->reg_phy + EXYNOS_4210_UPHYPWR);
+
+ rst = readl(drv->reg_phy + EXYNOS_4210_UPHYRST);
+ rst |= rstbits;
+ writel(rst, drv->reg_phy + EXYNOS_4210_UPHYRST);
+ udelay(10);
+ rst &= ~rstbits;
+ writel(rst, drv->reg_phy + EXYNOS_4210_UPHYRST);
+ /* The following delay is necessary for the reset sequence to be
+ * completed */
+ udelay(80);
+ } else {
+ pwr = readl(drv->reg_phy + EXYNOS_4210_UPHYPWR);
+ pwr |= phypwr;
+ writel(pwr, drv->reg_phy + EXYNOS_4210_UPHYPWR);
+ }
+}
+
+static int exynos4210_power_on(struct samsung_usb2_phy_instance *inst)
+{
+ /* Order of initialisation is important - first power then isolation */
+ exynos4210_phy_pwr(inst, 1);
+ exynos4210_isol(inst, 0);
+
+ return 0;
+}
+
+static int exynos4210_power_off(struct samsung_usb2_phy_instance *inst)
+{
+ exynos4210_isol(inst, 1);
+ exynos4210_phy_pwr(inst, 0);
+
+ return 0;
+}
+
+
+static const struct samsung_usb2_common_phy exynos4210_phys[] = {
+ {
+ .label = "device",
+ .id = EXYNOS4210_DEVICE,
+ .power_on = exynos4210_power_on,
+ .power_off = exynos4210_power_off,
+ },
+ {
+ .label = "host",
+ .id = EXYNOS4210_HOST,
+ .power_on = exynos4210_power_on,
+ .power_off = exynos4210_power_off,
+ },
+ {
+ .label = "hsic0",
+ .id = EXYNOS4210_HSIC0,
+ .power_on = exynos4210_power_on,
+ .power_off = exynos4210_power_off,
+ },
+ {
+ .label = "hsic1",
+ .id = EXYNOS4210_HSIC1,
+ .power_on = exynos4210_power_on,
+ .power_off = exynos4210_power_off,
+ },
+ {},
+};
+
+const struct samsung_usb2_phy_config exynos4210_usb2_phy_config = {
+ .has_mode_switch = 0,
+ .num_phys = EXYNOS4210_NUM_PHYS,
+ .phys = exynos4210_phys,
+ .rate_to_clk = exynos4210_rate_to_clk,
+};
--- /dev/null
+/*
+ * Samsung SoC USB 1.1/2.0 PHY driver - Exynos 4x12 support
+ *
+ * Copyright (C) 2013 Samsung Electronics Co., Ltd.
+ * Author: Kamil Debski <k.debski@samsung.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/delay.h>
+#include <linux/io.h>
+#include <linux/phy/phy.h>
+#include <linux/regmap.h>
+#include "phy-samsung-usb2.h"
+
+/* Exynos USB PHY registers */
+
+/* PHY power control */
+#define EXYNOS_4x12_UPHYPWR 0x0
+
+#define EXYNOS_4x12_UPHYPWR_PHY0_SUSPEND BIT(0)
+#define EXYNOS_4x12_UPHYPWR_PHY0_PWR BIT(3)
+#define EXYNOS_4x12_UPHYPWR_PHY0_OTG_PWR BIT(4)
+#define EXYNOS_4x12_UPHYPWR_PHY0_SLEEP BIT(5)
+#define EXYNOS_4x12_UPHYPWR_PHY0 ( \
+ EXYNOS_4x12_UPHYPWR_PHY0_SUSPEND | \
+ EXYNOS_4x12_UPHYPWR_PHY0_PWR | \
+ EXYNOS_4x12_UPHYPWR_PHY0_OTG_PWR | \
+ EXYNOS_4x12_UPHYPWR_PHY0_SLEEP)
+
+#define EXYNOS_4x12_UPHYPWR_PHY1_SUSPEND BIT(6)
+#define EXYNOS_4x12_UPHYPWR_PHY1_PWR BIT(7)
+#define EXYNOS_4x12_UPHYPWR_PHY1_SLEEP BIT(8)
+#define EXYNOS_4x12_UPHYPWR_PHY1 ( \
+ EXYNOS_4x12_UPHYPWR_PHY1_SUSPEND | \
+ EXYNOS_4x12_UPHYPWR_PHY1_PWR | \
+ EXYNOS_4x12_UPHYPWR_PHY1_SLEEP)
+
+#define EXYNOS_4x12_UPHYPWR_HSIC0_SUSPEND BIT(9)
+#define EXYNOS_4x12_UPHYPWR_HSIC0_PWR BIT(10)
+#define EXYNOS_4x12_UPHYPWR_HSIC0_SLEEP BIT(11)
+#define EXYNOS_4x12_UPHYPWR_HSIC0 ( \
+ EXYNOS_4x12_UPHYPWR_HSIC0_SUSPEND | \
+ EXYNOS_4x12_UPHYPWR_HSIC0_PWR | \
+ EXYNOS_4x12_UPHYPWR_HSIC0_SLEEP)
+
+#define EXYNOS_4x12_UPHYPWR_HSIC1_SUSPEND BIT(12)
+#define EXYNOS_4x12_UPHYPWR_HSIC1_PWR BIT(13)
+#define EXYNOS_4x12_UPHYPWR_HSIC1_SLEEP BIT(14)
+#define EXYNOS_4x12_UPHYPWR_HSIC1 ( \
+ EXYNOS_4x12_UPHYPWR_HSIC1_SUSPEND | \
+ EXYNOS_4x12_UPHYPWR_HSIC1_PWR | \
+ EXYNOS_4x12_UPHYPWR_HSIC1_SLEEP)
+
+/* PHY clock control */
+#define EXYNOS_4x12_UPHYCLK 0x4
+
+#define EXYNOS_4x12_UPHYCLK_PHYFSEL_MASK (0x7 << 0)
+#define EXYNOS_4x12_UPHYCLK_PHYFSEL_OFFSET 0
+#define EXYNOS_4x12_UPHYCLK_PHYFSEL_9MHZ6 (0x0 << 0)
+#define EXYNOS_4x12_UPHYCLK_PHYFSEL_10MHZ (0x1 << 0)
+#define EXYNOS_4x12_UPHYCLK_PHYFSEL_12MHZ (0x2 << 0)
+#define EXYNOS_4x12_UPHYCLK_PHYFSEL_19MHZ2 (0x3 << 0)
+#define EXYNOS_4x12_UPHYCLK_PHYFSEL_20MHZ (0x4 << 0)
+#define EXYNOS_4x12_UPHYCLK_PHYFSEL_24MHZ (0x5 << 0)
+#define EXYNOS_4x12_UPHYCLK_PHYFSEL_50MHZ (0x7 << 0)
+
+#define EXYNOS_4x12_UPHYCLK_PHY0_ID_PULLUP BIT(3)
+#define EXYNOS_4x12_UPHYCLK_PHY0_COMMON_ON BIT(4)
+#define EXYNOS_4x12_UPHYCLK_PHY1_COMMON_ON BIT(7)
+
+#define EXYNOS_4x12_UPHYCLK_HSIC_REFCLK_MASK (0x7f << 10)
+#define EXYNOS_4x12_UPHYCLK_HSIC_REFCLK_OFFSET 10
+#define EXYNOS_4x12_UPHYCLK_HSIC_REFCLK_12MHZ (0x24 << 10)
+#define EXYNOS_4x12_UPHYCLK_HSIC_REFCLK_15MHZ (0x1c << 10)
+#define EXYNOS_4x12_UPHYCLK_HSIC_REFCLK_16MHZ (0x1a << 10)
+#define EXYNOS_4x12_UPHYCLK_HSIC_REFCLK_19MHZ2 (0x15 << 10)
+#define EXYNOS_4x12_UPHYCLK_HSIC_REFCLK_20MHZ (0x14 << 10)
+
+/* PHY reset control */
+#define EXYNOS_4x12_UPHYRST 0x8
+
+#define EXYNOS_4x12_URSTCON_PHY0 BIT(0)
+#define EXYNOS_4x12_URSTCON_OTG_HLINK BIT(1)
+#define EXYNOS_4x12_URSTCON_OTG_PHYLINK BIT(2)
+#define EXYNOS_4x12_URSTCON_HOST_PHY BIT(3)
+#define EXYNOS_4x12_URSTCON_PHY1 BIT(4)
+#define EXYNOS_4x12_URSTCON_HSIC0 BIT(5)
+#define EXYNOS_4x12_URSTCON_HSIC1 BIT(6)
+#define EXYNOS_4x12_URSTCON_HOST_LINK_ALL BIT(7)
+#define EXYNOS_4x12_URSTCON_HOST_LINK_P0 BIT(8)
+#define EXYNOS_4x12_URSTCON_HOST_LINK_P1 BIT(9)
+#define EXYNOS_4x12_URSTCON_HOST_LINK_P2 BIT(10)
+
+/* Isolation, configured in the power management unit */
+#define EXYNOS_4x12_USB_ISOL_OFFSET 0x704
+#define EXYNOS_4x12_USB_ISOL_OTG BIT(0)
+#define EXYNOS_4x12_USB_ISOL_HSIC0_OFFSET 0x708
+#define EXYNOS_4x12_USB_ISOL_HSIC0 BIT(0)
+#define EXYNOS_4x12_USB_ISOL_HSIC1_OFFSET 0x70c
+#define EXYNOS_4x12_USB_ISOL_HSIC1 BIT(0)
+
+/* Mode switching SUB Device <-> Host */
+#define EXYNOS_4x12_MODE_SWITCH_OFFSET 0x21c
+#define EXYNOS_4x12_MODE_SWITCH_MASK 1
+#define EXYNOS_4x12_MODE_SWITCH_DEVICE 0
+#define EXYNOS_4x12_MODE_SWITCH_HOST 1
+
+enum exynos4x12_phy_id {
+ EXYNOS4x12_DEVICE,
+ EXYNOS4x12_HOST,
+ EXYNOS4x12_HSIC0,
+ EXYNOS4x12_HSIC1,
+ EXYNOS4x12_NUM_PHYS,
+};
+
+/*
+ * exynos4x12_rate_to_clk() converts the supplied clock rate to the value that
+ * can be written to the phy register.
+ */
+static int exynos4x12_rate_to_clk(unsigned long rate, u32 *reg)
+{
+ /* EXYNOS_4x12_UPHYCLK_PHYFSEL_MASK */
+
+ switch (rate) {
+ case 9600 * KHZ:
+ *reg = EXYNOS_4x12_UPHYCLK_PHYFSEL_9MHZ6;
+ break;
+ case 10 * MHZ:
+ *reg = EXYNOS_4x12_UPHYCLK_PHYFSEL_10MHZ;
+ break;
+ case 12 * MHZ:
+ *reg = EXYNOS_4x12_UPHYCLK_PHYFSEL_12MHZ;
+ break;
+ case 19200 * KHZ:
+ *reg = EXYNOS_4x12_UPHYCLK_PHYFSEL_19MHZ2;
+ break;
+ case 20 * MHZ:
+ *reg = EXYNOS_4x12_UPHYCLK_PHYFSEL_20MHZ;
+ break;
+ case 24 * MHZ:
+ *reg = EXYNOS_4x12_UPHYCLK_PHYFSEL_24MHZ;
+ break;
+ case 50 * MHZ:
+ *reg = EXYNOS_4x12_UPHYCLK_PHYFSEL_50MHZ;
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
+static void exynos4x12_isol(struct samsung_usb2_phy_instance *inst, bool on)
+{
+ struct samsung_usb2_phy_driver *drv = inst->drv;
+ u32 offset;
+ u32 mask;
+
+ switch (inst->cfg->id) {
+ case EXYNOS4x12_DEVICE:
+ case EXYNOS4x12_HOST:
+ offset = EXYNOS_4x12_USB_ISOL_OFFSET;
+ mask = EXYNOS_4x12_USB_ISOL_OTG;
+ break;
+ case EXYNOS4x12_HSIC0:
+ offset = EXYNOS_4x12_USB_ISOL_HSIC0_OFFSET;
+ mask = EXYNOS_4x12_USB_ISOL_HSIC0;
+ break;
+ case EXYNOS4x12_HSIC1:
+ offset = EXYNOS_4x12_USB_ISOL_HSIC1_OFFSET;
+ mask = EXYNOS_4x12_USB_ISOL_HSIC1;
+ break;
+ default:
+ return;
+ };
+
+ regmap_update_bits(drv->reg_pmu, offset, mask, on ? 0 : mask);
+}
+
+static void exynos4x12_setup_clk(struct samsung_usb2_phy_instance *inst)
+{
+ struct samsung_usb2_phy_driver *drv = inst->drv;
+ u32 clk;
+
+ clk = readl(drv->reg_phy + EXYNOS_4x12_UPHYCLK);
+ clk &= ~EXYNOS_4x12_UPHYCLK_PHYFSEL_MASK;
+ clk |= drv->ref_reg_val << EXYNOS_4x12_UPHYCLK_PHYFSEL_OFFSET;
+ writel(clk, drv->reg_phy + EXYNOS_4x12_UPHYCLK);
+}
+
+static void exynos4x12_phy_pwr(struct samsung_usb2_phy_instance *inst, bool on)
+{
+ struct samsung_usb2_phy_driver *drv = inst->drv;
+ u32 rstbits = 0;
+ u32 phypwr = 0;
+ u32 rst;
+ u32 pwr;
+ u32 mode = 0;
+ u32 switch_mode = 0;
+
+ switch (inst->cfg->id) {
+ case EXYNOS4x12_DEVICE:
+ phypwr = EXYNOS_4x12_UPHYPWR_PHY0;
+ rstbits = EXYNOS_4x12_URSTCON_PHY0;
+ mode = EXYNOS_4x12_MODE_SWITCH_DEVICE;
+ switch_mode = 1;
+ break;
+ case EXYNOS4x12_HOST:
+ phypwr = EXYNOS_4x12_UPHYPWR_PHY1;
+ rstbits = EXYNOS_4x12_URSTCON_HOST_PHY;
+ mode = EXYNOS_4x12_MODE_SWITCH_HOST;
+ switch_mode = 1;
+ break;
+ case EXYNOS4x12_HSIC0:
+ phypwr = EXYNOS_4x12_UPHYPWR_HSIC0;
+ rstbits = EXYNOS_4x12_URSTCON_HSIC1 |
+ EXYNOS_4x12_URSTCON_HOST_LINK_P0 |
+ EXYNOS_4x12_URSTCON_HOST_PHY;
+ break;
+ case EXYNOS4x12_HSIC1:
+ phypwr = EXYNOS_4x12_UPHYPWR_HSIC1;
+ rstbits = EXYNOS_4x12_URSTCON_HSIC1 |
+ EXYNOS_4x12_URSTCON_HOST_LINK_P1;
+ break;
+ };
+
+ if (on) {
+ if (switch_mode)
+ regmap_update_bits(drv->reg_sys,
+ EXYNOS_4x12_MODE_SWITCH_OFFSET,
+ EXYNOS_4x12_MODE_SWITCH_MASK, mode);
+
+ pwr = readl(drv->reg_phy + EXYNOS_4x12_UPHYPWR);
+ pwr &= ~phypwr;
+ writel(pwr, drv->reg_phy + EXYNOS_4x12_UPHYPWR);
+
+ rst = readl(drv->reg_phy + EXYNOS_4x12_UPHYRST);
+ rst |= rstbits;
+ writel(rst, drv->reg_phy + EXYNOS_4x12_UPHYRST);
+ udelay(10);
+ rst &= ~rstbits;
+ writel(rst, drv->reg_phy + EXYNOS_4x12_UPHYRST);
+ /* The following delay is necessary for the reset sequence to be
+ * completed */
+ udelay(80);
+ } else {
+ pwr = readl(drv->reg_phy + EXYNOS_4x12_UPHYPWR);
+ pwr |= phypwr;
+ writel(pwr, drv->reg_phy + EXYNOS_4x12_UPHYPWR);
+ }
+}
+
+static int exynos4x12_power_on(struct samsung_usb2_phy_instance *inst)
+{
+ struct samsung_usb2_phy_driver *drv = inst->drv;
+
+ inst->enabled = 1;
+ exynos4x12_setup_clk(inst);
+ exynos4x12_phy_pwr(inst, 1);
+ exynos4x12_isol(inst, 0);
+
+ /* Power on the device, as it is necessary for HSIC to work */
+ if (inst->cfg->id == EXYNOS4x12_HSIC0) {
+ struct samsung_usb2_phy_instance *device =
+ &drv->instances[EXYNOS4x12_DEVICE];
+ exynos4x12_phy_pwr(device, 1);
+ exynos4x12_isol(device, 0);
+ }
+
+ return 0;
+}
+
+static int exynos4x12_power_off(struct samsung_usb2_phy_instance *inst)
+{
+ struct samsung_usb2_phy_driver *drv = inst->drv;
+ struct samsung_usb2_phy_instance *device =
+ &drv->instances[EXYNOS4x12_DEVICE];
+
+ inst->enabled = 0;
+ exynos4x12_isol(inst, 1);
+ exynos4x12_phy_pwr(inst, 0);
+
+ if (inst->cfg->id == EXYNOS4x12_HSIC0 && !device->enabled) {
+ exynos4x12_isol(device, 1);
+ exynos4x12_phy_pwr(device, 0);
+ }
+
+ return 0;
+}
+
+
+static const struct samsung_usb2_common_phy exynos4x12_phys[] = {
+ {
+ .label = "device",
+ .id = EXYNOS4x12_DEVICE,
+ .power_on = exynos4x12_power_on,
+ .power_off = exynos4x12_power_off,
+ },
+ {
+ .label = "host",
+ .id = EXYNOS4x12_HOST,
+ .power_on = exynos4x12_power_on,
+ .power_off = exynos4x12_power_off,
+ },
+ {
+ .label = "hsic0",
+ .id = EXYNOS4x12_HSIC0,
+ .power_on = exynos4x12_power_on,
+ .power_off = exynos4x12_power_off,
+ },
+ {
+ .label = "hsic1",
+ .id = EXYNOS4x12_HSIC1,
+ .power_on = exynos4x12_power_on,
+ .power_off = exynos4x12_power_off,
+ },
+ {},
+};
+
+const struct samsung_usb2_phy_config exynos4x12_usb2_phy_config = {
+ .has_mode_switch = 1,
+ .num_phys = EXYNOS4x12_NUM_PHYS,
+ .phys = exynos4x12_phys,
+ .rate_to_clk = exynos4x12_rate_to_clk,
+};
--- /dev/null
+/*
+ * Samsung SoC USB 1.1/2.0 PHY driver
+ *
+ * Copyright (C) 2013 Samsung Electronics Co., Ltd.
+ * Author: Kamil Debski <k.debski@samsung.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/clk.h>
+#include <linux/mfd/syscon.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/phy/phy.h>
+#include <linux/platform_device.h>
+#include <linux/spinlock.h>
+#include "phy-samsung-usb2.h"
+
+static int samsung_usb2_phy_power_on(struct phy *phy)
+{
+ struct samsung_usb2_phy_instance *inst = phy_get_drvdata(phy);
+ struct samsung_usb2_phy_driver *drv = inst->drv;
+ int ret;
+
+ dev_dbg(drv->dev, "Request to power_on \"%s\" usb phy\n",
+ inst->cfg->label);
+ ret = clk_prepare_enable(drv->clk);
+ if (ret)
+ goto err_main_clk;
+ ret = clk_prepare_enable(drv->ref_clk);
+ if (ret)
+ goto err_instance_clk;
+ if (inst->cfg->power_on) {
+ spin_lock(&drv->lock);
+ ret = inst->cfg->power_on(inst);
+ spin_unlock(&drv->lock);
+ }
+
+ return 0;
+
+err_instance_clk:
+ clk_disable_unprepare(drv->clk);
+err_main_clk:
+ return ret;
+}
+
+static int samsung_usb2_phy_power_off(struct phy *phy)
+{
+ struct samsung_usb2_phy_instance *inst = phy_get_drvdata(phy);
+ struct samsung_usb2_phy_driver *drv = inst->drv;
+ int ret = 0;
+
+ dev_dbg(drv->dev, "Request to power_off \"%s\" usb phy\n",
+ inst->cfg->label);
+ if (inst->cfg->power_off) {
+ spin_lock(&drv->lock);
+ ret = inst->cfg->power_off(inst);
+ spin_unlock(&drv->lock);
+ }
+ clk_disable_unprepare(drv->ref_clk);
+ clk_disable_unprepare(drv->clk);
+ return ret;
+}
+
+static struct phy_ops samsung_usb2_phy_ops = {
+ .power_on = samsung_usb2_phy_power_on,
+ .power_off = samsung_usb2_phy_power_off,
+ .owner = THIS_MODULE,
+};
+
+static struct phy *samsung_usb2_phy_xlate(struct device *dev,
+ struct of_phandle_args *args)
+{
+ struct samsung_usb2_phy_driver *drv;
+
+ drv = dev_get_drvdata(dev);
+ if (!drv)
+ return ERR_PTR(-EINVAL);
+
+ if (WARN_ON(args->args[0] >= drv->cfg->num_phys))
+ return ERR_PTR(-ENODEV);
+
+ return drv->instances[args->args[0]].phy;
+}
+
+static const struct of_device_id samsung_usb2_phy_of_match[] = {
+#ifdef CONFIG_PHY_EXYNOS4210_USB2
+ {
+ .compatible = "samsung,exynos4210-usb2-phy",
+ .data = &exynos4210_usb2_phy_config,
+ },
+#endif
+#ifdef CONFIG_PHY_EXYNOS4X12_USB2
+ {
+ .compatible = "samsung,exynos4x12-usb2-phy",
+ .data = &exynos4x12_usb2_phy_config,
+ },
+#endif
+ { },
+};
+
+static int samsung_usb2_phy_probe(struct platform_device *pdev)
+{
+ const struct of_device_id *match;
+ const struct samsung_usb2_phy_config *cfg;
+ struct device *dev = &pdev->dev;
+ struct phy_provider *phy_provider;
+ struct resource *mem;
+ struct samsung_usb2_phy_driver *drv;
+ int i, ret;
+
+ if (!pdev->dev.of_node) {
+ dev_err(dev, "This driver is required to be instantiated from device tree\n");
+ return -EINVAL;
+ }
+
+ match = of_match_node(samsung_usb2_phy_of_match, pdev->dev.of_node);
+ if (!match) {
+ dev_err(dev, "of_match_node() failed\n");
+ return -EINVAL;
+ }
+ cfg = match->data;
+
+ drv = devm_kzalloc(dev, sizeof(struct samsung_usb2_phy_driver) +
+ cfg->num_phys * sizeof(struct samsung_usb2_phy_instance),
+ GFP_KERNEL);
+ if (!drv)
+ return -ENOMEM;
+
+ dev_set_drvdata(dev, drv);
+ spin_lock_init(&drv->lock);
+
+ drv->cfg = cfg;
+ drv->dev = dev;
+
+ mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ drv->reg_phy = devm_ioremap_resource(dev, mem);
+ if (IS_ERR(drv->reg_phy)) {
+ dev_err(dev, "Failed to map register memory (phy)\n");
+ return PTR_ERR(drv->reg_phy);
+ }
+
+ drv->reg_pmu = syscon_regmap_lookup_by_phandle(pdev->dev.of_node,
+ "samsung,pmureg-phandle");
+ if (IS_ERR(drv->reg_pmu)) {
+ dev_err(dev, "Failed to map PMU registers (via syscon)\n");
+ return PTR_ERR(drv->reg_pmu);
+ }
+
+ if (drv->cfg->has_mode_switch) {
+ drv->reg_sys = syscon_regmap_lookup_by_phandle(
+ pdev->dev.of_node, "samsung,sysreg-phandle");
+ if (IS_ERR(drv->reg_sys)) {
+ dev_err(dev, "Failed to map system registers (via syscon)\n");
+ return PTR_ERR(drv->reg_sys);
+ }
+ }
+
+ drv->clk = devm_clk_get(dev, "phy");
+ if (IS_ERR(drv->clk)) {
+ dev_err(dev, "Failed to get clock of phy controller\n");
+ return PTR_ERR(drv->clk);
+ }
+
+ drv->ref_clk = devm_clk_get(dev, "ref");
+ if (IS_ERR(drv->ref_clk)) {
+ dev_err(dev, "Failed to get reference clock for the phy controller\n");
+ return PTR_ERR(drv->ref_clk);
+ }
+
+ drv->ref_rate = clk_get_rate(drv->ref_clk);
+ if (drv->cfg->rate_to_clk) {
+ ret = drv->cfg->rate_to_clk(drv->ref_rate, &drv->ref_reg_val);
+ if (ret)
+ return ret;
+ }
+
+ for (i = 0; i < drv->cfg->num_phys; i++) {
+ char *label = drv->cfg->phys[i].label;
+ struct samsung_usb2_phy_instance *p = &drv->instances[i];
+
+ dev_dbg(dev, "Creating phy \"%s\"\n", label);
+ p->phy = devm_phy_create(dev, &samsung_usb2_phy_ops, NULL);
+ if (IS_ERR(p->phy)) {
+ dev_err(drv->dev, "Failed to create usb2_phy \"%s\"\n",
+ label);
+ return PTR_ERR(p->phy);
+ }
+
+ p->cfg = &drv->cfg->phys[i];
+ p->drv = drv;
+ phy_set_bus_width(p->phy, 8);
+ phy_set_drvdata(p->phy, p);
+ }
+
+ phy_provider = devm_of_phy_provider_register(dev,
+ samsung_usb2_phy_xlate);
+ if (IS_ERR(phy_provider)) {
+ dev_err(drv->dev, "Failed to register phy provider\n");
+ return PTR_ERR(phy_provider);
+ }
+
+ return 0;
+}
+
+static struct platform_driver samsung_usb2_phy_driver = {
+ .probe = samsung_usb2_phy_probe,
+ .driver = {
+ .of_match_table = samsung_usb2_phy_of_match,
+ .name = "samsung-usb2-phy",
+ .owner = THIS_MODULE,
+ }
+};
+
+module_platform_driver(samsung_usb2_phy_driver);
+MODULE_DESCRIPTION("Samsung S5P/EXYNOS SoC USB PHY driver");
+MODULE_AUTHOR("Kamil Debski <k.debski@samsung.com>");
+MODULE_LICENSE("GPL v2");
+MODULE_ALIAS("platform:samsung-usb2-phy");
--- /dev/null
+/*
+ * Samsung SoC USB 1.1/2.0 PHY driver
+ *
+ * Copyright (C) 2013 Samsung Electronics Co., Ltd.
+ * Author: Kamil Debski <k.debski@samsung.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef _PHY_EXYNOS_USB2_H
+#define _PHY_EXYNOS_USB2_H
+
+#include <linux/clk.h>
+#include <linux/phy/phy.h>
+#include <linux/device.h>
+#include <linux/regmap.h>
+#include <linux/spinlock.h>
+
+#define KHZ 1000
+#define MHZ (KHZ * KHZ)
+
+struct samsung_usb2_phy_driver;
+struct samsung_usb2_phy_instance;
+struct samsung_usb2_phy_config;
+
+struct samsung_usb2_phy_instance {
+ const struct samsung_usb2_common_phy *cfg;
+ struct phy *phy;
+ struct samsung_usb2_phy_driver *drv;
+ bool enabled;
+};
+
+struct samsung_usb2_phy_driver {
+ const struct samsung_usb2_phy_config *cfg;
+ struct clk *clk;
+ struct clk *ref_clk;
+ unsigned long ref_rate;
+ u32 ref_reg_val;
+ struct device *dev;
+ void __iomem *reg_phy;
+ struct regmap *reg_pmu;
+ struct regmap *reg_sys;
+ spinlock_t lock;
+ struct samsung_usb2_phy_instance instances[0];
+};
+
+struct samsung_usb2_common_phy {
+ int (*power_on)(struct samsung_usb2_phy_instance *);
+ int (*power_off)(struct samsung_usb2_phy_instance *);
+ unsigned int id;
+ char *label;
+};
+
+
+struct samsung_usb2_phy_config {
+ const struct samsung_usb2_common_phy *phys;
+ int (*rate_to_clk)(unsigned long, u32 *);
+ unsigned int num_phys;
+ bool has_mode_switch;
+};
+
+extern const struct samsung_usb2_phy_config exynos4210_usb2_phy_config;
+extern const struct samsung_usb2_phy_config exynos4x12_usb2_phy_config;
+#endif
projects / platform / kernel / linux-starfive.git / commitdiff