--- /dev/null
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/memory-controllers/ti,gpmc-child.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: device tree bindings for children of the Texas Instruments GPMC
+
+maintainers:
+ - Tony Lindgren <tony@atomide.com>
+ - Roger Quadros <rogerq@kernel.org>
+
+description:
+ This binding is meant for the child nodes of the GPMC node. The node
+ represents any device connected to the GPMC bus. It may be a Flash chip,
+ RAM chip or Ethernet controller, etc. These properties are meant for
+ configuring the GPMC settings/timings and will accompany the bindings
+ supported by the respective device.
+
+properties:
+ reg: true
+
+# GPMC Timing properties for child nodes. All are optional and default to 0.
+ gpmc,sync-clk-ps:
+ description: Minimum clock period for synchronous mode
+ default: 0
+
+# Chip-select signal timings corresponding to GPMC_CONFIG2:
+ gpmc,cs-on-ns:
+ description: Assertion time
+ default: 0
+
+ gpmc,cs-rd-off-ns:
+ description: Read deassertion time
+ default: 0
+
+ gpmc,cs-wr-off-ns:
+ description: Write deassertion time
+ default: 0
+
+# ADV signal timings corresponding to GPMC_CONFIG3:
+ gpmc,adv-on-ns:
+ description: Assertion time
+ default: 0
+
+ gpmc,adv-rd-off-ns:
+ description: Read deassertion time
+ default: 0
+
+ gpmc,adv-wr-off-ns:
+ description: Write deassertion time
+ default: 0
+
+ gpmc,adv-aad-mux-on-ns:
+ description: Assertion time for AAD
+ default: 0
+
+ gpmc,adv-aad-mux-rd-off-ns:
+ description: Read deassertion time for AAD
+ default: 0
+
+ gpmc,adv-aad-mux-wr-off-ns:
+ description: Write deassertion time for AAD
+ default: 0
+
+# WE signals timings corresponding to GPMC_CONFIG4:
+ gpmc,we-on-ns:
+ description: Assertion time
+ default: 0
+
+ gpmc,we-off-ns:
+ description: Deassertion time
+ default: 0
+
+# OE signals timings corresponding to GPMC_CONFIG4:
+ gpmc,oe-on-ns:
+ description: Assertion time
+ default: 0
+
+ gpmc,oe-off-ns:
+ description: Deassertion time
+ default: 0
+
+ gpmc,oe-aad-mux-on-ns:
+ description: Assertion time for AAD
+ default: 0
+
+ gpmc,oe-aad-mux-off-ns:
+ description: Deassertion time for AAD
+ default: 0
+
+# Access time and cycle time timings (in nanoseconds) corresponding to
+# GPMC_CONFIG5:
+ gpmc,page-burst-access-ns:
+ description: Multiple access word delay
+ default: 0
+
+ gpmc,access-ns:
+ description: Start-cycle to first data valid delay
+ default: 0
+
+ gpmc,rd-cycle-ns:
+ description: Total read cycle time
+ default: 0
+
+ gpmc,wr-cycle-ns:
+ description: Total write cycle time
+ default: 0
+
+ gpmc,bus-turnaround-ns:
+ description: Turn-around time between successive accesses
+ default: 0
+
+ gpmc,cycle2cycle-delay-ns:
+ description: Delay between chip-select pulses
+ default: 0
+
+ gpmc,clk-activation-ns:
+ description: GPMC clock activation time
+ default: 0
+
+ gpmc,wait-monitoring-ns:
+ description: Start of wait monitoring with regard to valid data
+ default: 0
+
+# Boolean timing parameters. If property is present, parameter is enabled
+# otherwise disabled.
+ gpmc,adv-extra-delay:
+ description: ADV signal is delayed by half GPMC clock
+ type: boolean
+
+ gpmc,cs-extra-delay:
+ description: CS signal is delayed by half GPMC clock
+ type: boolean
+
+ gpmc,cycle2cycle-diffcsen:
+ description: |
+ Add "cycle2cycle-delay" between successive accesses
+ to a different CS
+ type: boolean
+
+ gpmc,cycle2cycle-samecsen:
+ description: |
+ Add "cycle2cycle-delay" between successive accesses
+ to the same CS
+ type: boolean
+
+ gpmc,oe-extra-delay:
+ description: OE signal is delayed by half GPMC clock
+ type: boolean
+
+ gpmc,we-extra-delay:
+ description: WE signal is delayed by half GPMC clock
+ type: boolean
+
+ gpmc,time-para-granularity:
+ description: Multiply all access times by 2
+ type: boolean
+
+# The following two properties are applicable only to OMAP3+ and AM335x:
+ gpmc,wr-access-ns:
+ description: |
+ In synchronous write mode, for single or
+ burst accesses, defines the number of
+ GPMC_FCLK cycles from start access time
+ to the GPMC_CLK rising edge used by the
+ memory device for the first data capture.
+ default: 0
+
+ gpmc,wr-data-mux-bus-ns:
+ description: |
+ In address-data multiplex mode, specifies
+ the time when the first data is driven on
+ the address-data bus.
+ default: 0
+
+# GPMC chip-select settings properties for child nodes. All are optional.
+ gpmc,burst-length:
+ description: Page/burst length.
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [0, 4, 8, 16]
+ default: 0
+
+ gpmc,burst-wrap:
+ description: Enables wrap bursting
+ type: boolean
+
+ gpmc,burst-read:
+ description: Enables read page/burst mode
+ type: boolean
+
+ gpmc,burst-write:
+ description: Enables write page/burst mode
+ type: boolean
+
+ gpmc,device-width:
+ description: |
+ Total width of device(s) connected to a GPMC
+ chip-select in bytes. The GPMC supports 8-bit
+ and 16-bit devices and so this property must be
+ 1 or 2.
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [1, 2]
+ default: 1
+
+ gpmc,mux-add-data:
+ description: |
+ Address and data multiplexing configuration.
+ Valid values are
+ 0 for Non multiplexed mode
+ 1 for address-address-data multiplexing mode and
+ 2 for address-data multiplexing mode.
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [0, 1, 2]
+
+ gpmc,sync-read:
+ description: |
+ Enables synchronous read. Defaults to asynchronous
+ is this is not set.
+ type: boolean
+
+ gpmc,sync-write:
+ description: |
+ Enables synchronous writes. Defaults to asynchronous
+ is this is not set.
+ type: boolean
+
+ gpmc,wait-pin:
+ description: |
+ Wait-pin used by client. Must be less than "gpmc,num-waitpins".
+ $ref: /schemas/types.yaml#/definitions/uint32
+
+ gpmc,wait-on-read:
+ description: Enables wait monitoring on reads.
+ type: boolean
+
+ gpmc,wait-on-write:
+ description: Enables wait monitoring on writes.
+ type: boolean
+
+required:
+ - reg
+
+# the GPMC child will have its own native properties
+additionalProperties: true