b43: enable mesh
authorJohannes Berg <johannes@sipsolutions.net>
Tue, 20 May 2008 10:10:49 +0000 (12:10 +0200)
committerJohn W. Linville <linville@tuxdriver.com>
Tue, 3 Jun 2008 19:00:13 +0000 (15:00 -0400)
This patch enables b43 to do mesh networking, tested against my zd1211rw
dongle.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Reviewed-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
drivers/net/wireless/b43/main.c

index cbb317b..f9c14c6 100644 (file)
@@ -1430,11 +1430,17 @@ static void b43_write_beacon_template(struct b43_wldev *dev,
                i += ie_len + 2;
        }
        if (!tim_found) {
-               b43warn(dev->wl, "Did not find a valid TIM IE in "
-                       "the beacon template packet. AP or IBSS operation "
-                       "may be broken.\n");
-       } else
-               b43dbg(dev->wl, "Updated beacon template\n");
+               /*
+                * If ucode wants to modify TIM do it behind the beacon, this
+                * will happen, for example, when doing mesh networking.
+                */
+               b43_shm_write16(dev, B43_SHM_SHARED,
+                               B43_SHM_SH_TIMBPOS,
+                               len + sizeof(struct b43_plcp_hdr6));
+               b43_shm_write16(dev, B43_SHM_SHARED,
+                               B43_SHM_SH_DTIMPER, 0);
+       }
+       b43dbg(dev->wl, "Updated beacon template at 0x%x\n", ram_offset);
 }
 
 static void b43_write_probe_resp_plcp(struct b43_wldev *dev,
@@ -1549,7 +1555,8 @@ static void handle_irq_beacon(struct b43_wldev *dev)
        struct b43_wl *wl = dev->wl;
        u32 cmd, beacon0_valid, beacon1_valid;
 
-       if (!b43_is_mode(wl, IEEE80211_IF_TYPE_AP))
+       if (!b43_is_mode(wl, IEEE80211_IF_TYPE_AP) &&
+           !b43_is_mode(wl, IEEE80211_IF_TYPE_MESH_POINT))
                return;
 
        /* This is the bottom half of the asynchronous beacon update. */
@@ -2491,7 +2498,8 @@ static void b43_adjust_opmode(struct b43_wldev *dev)
        ctl &= ~B43_MACCTL_BEACPROMISC;
        ctl |= B43_MACCTL_INFRA;
 
-       if (b43_is_mode(wl, IEEE80211_IF_TYPE_AP))
+       if (b43_is_mode(wl, IEEE80211_IF_TYPE_AP) ||
+           b43_is_mode(wl, IEEE80211_IF_TYPE_MESH_POINT))
                ctl |= B43_MACCTL_AP;
        else if (b43_is_mode(wl, IEEE80211_IF_TYPE_IBSS))
                ctl &= ~B43_MACCTL_INFRA;
@@ -3358,8 +3366,9 @@ static int b43_op_config(struct ieee80211_hw *hw, struct ieee80211_conf *conf)
        antenna = b43_antenna_from_ieee80211(dev, conf->antenna_sel_rx);
        b43_set_rx_antenna(dev, antenna);
 
-       /* Update templates for AP mode. */
-       if (b43_is_mode(wl, IEEE80211_IF_TYPE_AP))
+       /* Update templates for AP/mesh mode. */
+       if (b43_is_mode(wl, IEEE80211_IF_TYPE_AP) ||
+           b43_is_mode(wl, IEEE80211_IF_TYPE_MESH_POINT))
                b43_set_beacon_int(dev, conf->beacon_int);
 
        if (!!conf->radio_enabled != phy->radio_on) {
@@ -3547,8 +3556,9 @@ static int b43_op_config_interface(struct ieee80211_hw *hw,
        else
                memset(wl->bssid, 0, ETH_ALEN);
        if (b43_status(dev) >= B43_STAT_INITIALIZED) {
-               if (b43_is_mode(wl, IEEE80211_IF_TYPE_AP)) {
-                       B43_WARN_ON(conf->type != IEEE80211_IF_TYPE_AP);
+               if (b43_is_mode(wl, IEEE80211_IF_TYPE_AP) ||
+                   b43_is_mode(wl, IEEE80211_IF_TYPE_MESH_POINT)) {
+                       B43_WARN_ON(conf->type != wl->if_type);
                        b43_set_ssid(dev, conf->ssid, conf->ssid_len);
                        if (conf->beacon)
                                b43_update_templates(wl, conf->beacon);
@@ -4088,6 +4098,7 @@ static int b43_op_add_interface(struct ieee80211_hw *hw,
        /* TODO: allow WDS/AP devices to coexist */
 
        if (conf->type != IEEE80211_IF_TYPE_AP &&
+           conf->type != IEEE80211_IF_TYPE_MESH_POINT &&
            conf->type != IEEE80211_IF_TYPE_STA &&
            conf->type != IEEE80211_IF_TYPE_WDS &&
            conf->type != IEEE80211_IF_TYPE_IBSS)