dt-bindings: drm/bridge: Document Cadence DSI bridge bindings

Document the bindings used for the Cadence DSI bridge.

Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180421070846.10330-2-boris.brezillon@bootlin.com

diff --git a/Documentation/devicetree/bindings/display/bridge/cdns,dsi.txt b/Documentation/devicetree/bindings/display/bridge/cdns,dsi.txt
new file mode 100644 (file)
index 0000000..f5725bb
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/bridge/cdns,dsi.txt
@@ -0,0 +1,133 @@
+Cadence DSI bridge
+==================
+
+The Cadence DSI bridge is a DPI to DSI bridge supporting up to 4 DSI lanes.
+
+Required properties:
+- compatible: should be set to "cdns,dsi".
+- reg: physical base address and length of the controller's registers.
+- interrupts: interrupt line connected to the DSI bridge.
+- clocks: DSI bridge clocks.
+- clock-names: must contain "dsi_p_clk" and "dsi_sys_clk".
+- phys: phandle link to the MIPI D-PHY controller.
+- phy-names: must contain "dphy".
+- #address-cells: must be set to 1.
+- #size-cells: must be set to 0.
+
+Optional properties:
+- resets: DSI reset lines.
+- reset-names: can contain "dsi_p_rst".
+
+Required subnodes:
+- ports: Ports as described in Documentation/devicetree/bindings/graph.txt.
+  2 ports are available:
+  * port 0: this port is only needed if some of your DSI devices are
+           controlled through  an external bus like I2C or SPI. Can have at
+           most 4 endpoints. The endpoint number is directly encoding the
+           DSI virtual channel used by this device.
+  * port 1: represents the DPI input.
+  Other ports will be added later to support the new kind of inputs.
+
+- one subnode per DSI device connected on the DSI bus. Each DSI device should
+  contain a reg property encoding its virtual channel.
+
+Cadence DPHY
+============
+
+Cadence DPHY block.
+
+Required properties:
+- compatible: should be set to "cdns,dphy".
+- reg: physical base address and length of the DPHY registers.
+- clocks: DPHY reference clocks.
+- clock-names: must contain "psm" and "pll_ref".
+- #phy-cells: must be set to 0.
+
+
+Example:
+       dphy0: dphy@fd0e0000{
+               compatible = "cdns,dphy";
+               reg = <0x0 0xfd0e0000 0x0 0x1000>;
+               clocks = <&psm_clk>, <&pll_ref_clk>;
+               clock-names = "psm", "pll_ref";
+               #phy-cells = <0>;
+       };
+
+       dsi0: dsi@fd0c0000 {
+               compatible = "cdns,dsi";
+               reg = <0x0 0xfd0c0000 0x0 0x1000>;
+               clocks = <&pclk>, <&sysclk>;
+               clock-names = "dsi_p_clk", "dsi_sys_clk";
+               interrupts = <1>;
+               phys = <&dphy0>;
+               phy-names = "dphy";
+               #address-cells = <1>;
+               #size-cells = <0>;
+
+               ports {
+                       #address-cells = <1>;
+                       #size-cells = <0>;
+
+                       port@1 {
+                               reg = <1>;
+                               dsi0_dpi_input: endpoint {
+                                       remote-endpoint = <&xxx_dpi_output>;
+                               };
+                       };
+               };
+
+               panel: dsi-dev@0 {
+                       compatible = "<vendor,panel>";
+                       reg = <0>;
+               };
+       };
+
+or
+
+       dsi0: dsi@fd0c0000 {
+               compatible = "cdns,dsi";
+               reg = <0x0 0xfd0c0000 0x0 0x1000>;
+               clocks = <&pclk>, <&sysclk>;
+               clock-names = "dsi_p_clk", "dsi_sys_clk";
+               interrupts = <1>;
+               phys = <&dphy1>;
+               phy-names = "dphy";
+               #address-cells = <1>;
+               #size-cells = <0>;
+
+               ports {
+                       #address-cells = <1>;
+                       #size-cells = <0>;
+
+                       port@0 {
+                               reg = <0>;
+                               #address-cells = <1>;
+                               #size-cells = <0>;
+
+                               dsi0_output: endpoint@0 {
+                                       reg = <0>;
+                                       remote-endpoint = <&dsi_panel_input>;
+                               };
+                       };
+
+                       port@1 {
+                               reg = <1>;
+                               dsi0_dpi_input: endpoint {
+                                       remote-endpoint = <&xxx_dpi_output>;
+                               };
+                       };
+               };
+       };
+
+       i2c@xxx {
+               panel: panel@59 {
+                       compatible = "<vendor,panel>";
+                       reg = <0x59>;
+
+                       port {
+                               dsi_panel_input: endpoint {
+                                       remote-endpoint = <&dsi0_output>;
+                               };
+                       };
+               };
+       };