source "board/siemens/pxm2/Kconfig"
source "board/siemens/rut/Kconfig"
source "board/silica/pengwyn/Kconfig"
+source "board/solidrun/clearfog/Kconfig"
source "board/spear/spear300/Kconfig"
source "board/spear/spear310/Kconfig"
source "board/spear/spear320/Kconfig"
tegra210-p2571.dtb
dtb-$(CONFIG_ARCH_MVEBU) += \
+ armada-388-clearfog.dtb \
armada-388-gp.dtb \
armada-xp-gp.dtb \
armada-xp-maxbcm.dtb
--- /dev/null
+/*
+ * Device Tree file for SolidRun Clearfog revision A1 rev 2.0 (88F6828)
+ *
+ * Copyright (C) 2015 Russell King
+ *
+ * This board is in development; the contents of this file work with
+ * the A1 rev 2.0 of the board, which does not represent final
+ * production board. Things will change, don't expect this file to
+ * remain compatible info the future.
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
+#include "armada-388.dtsi"
+
+/ {
+ model = "SolidRun Clearfog A1";
+ compatible = "solidrun,clearfog-a1", "marvell,armada388",
+ "marvell,armada385", "marvell,armada380";
+
+ aliases {
+ /* So that mvebu u-boot can update the MAC addresses */
+ ethernet1 = ð0;
+ ethernet2 = ð1;
+ ethernet3 = ð2;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0x00000000 0x10000000>; /* 256 MB */
+ };
+
+ reg_3p3v: regulator-3p3v {
+ compatible = "regulator-fixed";
+ regulator-name = "3P3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ soc {
+ ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000
+ MBUS_ID(0x01, 0x1d) 0 0xfff00000 0x100000
+ MBUS_ID(0x09, 0x19) 0 0xf1100000 0x10000
+ MBUS_ID(0x09, 0x15) 0 0xf1110000 0x10000>;
+
+ internal-regs {
+ ethernet@30000 {
+ mac-address = [00 50 43 02 02 02];
+ phy-mode = "sgmii";
+ status = "okay";
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+ };
+
+ ethernet@34000 {
+ mac-address = [00 50 43 02 02 03];
+ managed = "in-band-status";
+ phy-mode = "sgmii";
+ status = "okay";
+ };
+
+ ethernet@70000 {
+ mac-address = [00 50 43 02 02 01];
+ pinctrl-0 = <&ge0_rgmii_pins>;
+ pinctrl-names = "default";
+ phy = <&phy_dedicated>;
+ phy-mode = "rgmii-id";
+ status = "okay";
+ };
+
+ i2c@11000 {
+ /* Is there anything on this? */
+ clock-frequency = <100000>;
+ pinctrl-0 = <&i2c0_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+
+ /*
+ * PCA9655 GPIO expander, up to 1MHz clock.
+ * 0-CON3 CLKREQ#
+ * 1-CON3 PERST#
+ * 2-CON2 PERST#
+ * 3-CON3 W_DISABLE
+ * 4-CON2 CLKREQ#
+ * 5-USB3 overcurrent
+ * 6-USB3 power
+ * 7-CON2 W_DISABLE
+ * 8-JP4 P1
+ * 9-JP4 P4
+ * 10-JP4 P5
+ * 11-m.2 DEVSLP
+ * 12-SFP_LOS
+ * 13-SFP_TX_FAULT
+ * 14-SFP_TX_DISABLE
+ * 15-SFP_MOD_DEF0
+ */
+ expander0: gpio-expander@20 {
+ /*
+ * This is how it should be:
+ * compatible = "onnn,pca9655",
+ * "nxp,pca9555";
+ * but you can't do this because of
+ * the way I2C works.
+ */
+ compatible = "nxp,pca9555";
+ gpio-controller;
+ #gpio-cells = <2>;
+ reg = <0x20>;
+
+ pcie1_0_clkreq {
+ gpio-hog;
+ gpios = <0 GPIO_ACTIVE_LOW>;
+ input;
+ line-name = "pcie1.0-clkreq";
+ };
+ pcie1_0_w_disable {
+ gpio-hog;
+ gpios = <3 GPIO_ACTIVE_LOW>;
+ output-low;
+ line-name = "pcie1.0-w-disable";
+ };
+ pcie2_0_clkreq {
+ gpio-hog;
+ gpios = <4 GPIO_ACTIVE_LOW>;
+ input;
+ line-name = "pcie2.0-clkreq";
+ };
+ pcie2_0_w_disable {
+ gpio-hog;
+ gpios = <7 GPIO_ACTIVE_LOW>;
+ output-low;
+ line-name = "pcie2.0-w-disable";
+ };
+ usb3_ilimit {
+ gpio-hog;
+ gpios = <5 GPIO_ACTIVE_LOW>;
+ input;
+ line-name = "usb3-current-limit";
+ };
+ usb3_power {
+ gpio-hog;
+ gpios = <6 GPIO_ACTIVE_HIGH>;
+ output-high;
+ line-name = "usb3-power";
+ };
+ m2_devslp {
+ gpio-hog;
+ gpios = <11 GPIO_ACTIVE_HIGH>;
+ output-low;
+ line-name = "m.2 devslp";
+ };
+ };
+
+ /* The MCP3021 is 100kHz clock only */
+ mikrobus_adc: mcp3021@4c {
+ compatible = "microchip,mcp3021";
+ reg = <0x4c>;
+ };
+
+ /* Also something at 0x64 */
+ };
+
+ i2c@11100 {
+ /*
+ * Routed to SFP, mikrobus, and PCIe.
+ * SFP limits this to 100kHz, and requires
+ * an AT24C01A/02/04 with address pins tied
+ * low, which takes addresses 0x50 and 0x51.
+ * Mikrobus doesn't specify beyond an I2C
+ * bus being present.
+ * PCIe uses ARP to assign addresses, or
+ * 0x63-0x64.
+ */
+ clock-frequency = <100000>;
+ pinctrl-0 = <&clearfog_i2c1_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+ };
+
+ mdio@72004 {
+ pinctrl-0 = <&mdio_pins>;
+ pinctrl-names = "default";
+
+ phy_dedicated: ethernet-phy@0 {
+ /*
+ * Annoyingly, the marvell phy driver
+ * configures the LED register, rather
+ * than preserving reset-loaded setting.
+ * We undo that rubbish here.
+ */
+ marvell,reg-init = <3 16 0 0x101e>;
+ reg = <0>;
+ };
+ };
+
+ pinctrl@18000 {
+ clearfog_dsa0_clk_pins: clearfog-dsa0-clk-pins {
+ marvell,pins = "mpp46";
+ marvell,function = "ref";
+ };
+ clearfog_dsa0_pins: clearfog-dsa0-pins {
+ marvell,pins = "mpp23", "mpp41";
+ marvell,function = "gpio";
+ };
+ clearfog_i2c1_pins: i2c1-pins {
+ /* SFP, PCIe, mSATA, mikrobus */
+ marvell,pins = "mpp26", "mpp27";
+ marvell,function = "i2c1";
+ };
+ clearfog_sdhci_cd_pins: clearfog-sdhci-cd-pins {
+ marvell,pins = "mpp20";
+ marvell,function = "gpio";
+ };
+ clearfog_sdhci_pins: clearfog-sdhci-pins {
+ marvell,pins = "mpp21", "mpp28",
+ "mpp37", "mpp38",
+ "mpp39", "mpp40";
+ marvell,function = "sd0";
+ };
+ clearfog_spi1_cs_pins: spi1-cs-pins {
+ marvell,pins = "mpp55";
+ marvell,function = "spi1";
+ };
+ mikro_pins: mikro-pins {
+ /* int: mpp22 rst: mpp29 */
+ marvell,pins = "mpp22", "mpp29";
+ marvell,function = "gpio";
+ };
+ mikro_spi_pins: mikro-spi-pins {
+ marvell,pins = "mpp43";
+ marvell,function = "spi1";
+ };
+ mikro_uart_pins: mikro-uart-pins {
+ marvell,pins = "mpp24", "mpp25";
+ marvell,function = "ua1";
+ };
+ rear_button_pins: rear-button-pins {
+ marvell,pins = "mpp34";
+ marvell,function = "gpio";
+ };
+ };
+
+ rtc@a3800 {
+ /*
+ * If the rtc doesn't work, run "date reset"
+ * twice in u-boot.
+ */
+ status = "okay";
+ };
+
+ sata@a8000 {
+ /* pinctrl? */
+ status = "okay";
+ };
+
+ sata@e0000 {
+ /* pinctrl? */
+ status = "okay";
+ };
+
+ sdhci@d8000 {
+ bus-width = <4>;
+ cd-gpios = <&gpio0 20 GPIO_ACTIVE_LOW>;
+ no-1-8-v;
+ pinctrl-0 = <&clearfog_sdhci_pins
+ &clearfog_sdhci_cd_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+ vmmc = <®_3p3v>;
+ wp-inverted;
+ };
+
+ serial@12000 {
+ pinctrl-0 = <&uart0_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+ u-boot,dm-pre-reloc;
+ };
+
+ serial@12100 {
+ /* mikrobus uart */
+ pinctrl-0 = <&mikro_uart_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+ };
+
+ spi@10680 {
+ /*
+ * We don't seem to have the W25Q32 on the
+ * A1 Rev 2.0 boards, so disable SPI.
+ * CS0: W25Q32 (doesn't appear to be present)
+ * CS1:
+ * CS2: mikrobus
+ */
+ pinctrl-0 = <&spi1_pins &clearfog_spi1_cs_pins &mikro_spi_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+
+ spi-flash@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "w25q32", "jedec,spi-nor";
+ reg = <0>; /* Chip select 0 */
+ spi-max-frequency = <3000000>;
+ status = "disabled";
+ };
+ };
+
+ usb3@f8000 {
+ status = "okay";
+ };
+ };
+
+ pcie-controller {
+ status = "okay";
+ /*
+ * The two PCIe units are accessible through
+ * the mini-PCIe connectors on the board.
+ */
+ pcie@2,0 {
+ /* Port 1, Lane 0. CONN3, nearest power. */
+ reset-gpios = <&expander0 1 GPIO_ACTIVE_LOW>;
+ status = "okay";
+ };
+ pcie@3,0 {
+ /* Port 2, Lane 0. CONN2, nearest CPU. */
+ reset-gpios = <&expander0 2 GPIO_ACTIVE_LOW>;
+ status = "okay";
+ };
+ };
+ };
+
+ sfp: sfp {
+ compatible = "sff,sfp";
+ i2c-bus = <&i2c1>;
+ los-gpio = <&expander0 12 GPIO_ACTIVE_HIGH>;
+ moddef0-gpio = <&expander0 15 GPIO_ACTIVE_LOW>;
+ sfp,ethernet = <ð2>;
+ tx-disable-gpio = <&expander0 14 GPIO_ACTIVE_HIGH>;
+ tx-fault-gpio = <&expander0 13 GPIO_ACTIVE_HIGH>;
+ };
+
+ dsa@0 {
+ compatible = "marvell,dsa";
+ dsa,ethernet = <ð1>;
+ dsa,mii-bus = <&mdio>;
+ pinctrl-0 = <&clearfog_dsa0_clk_pins &clearfog_dsa0_pins>;
+ pinctrl-names = "default";
+ #address-cells = <2>;
+ #size-cells = <0>;
+
+ switch@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <4 0>;
+
+ port@0 {
+ reg = <0>;
+ label = "lan1";
+ };
+
+ port@1 {
+ reg = <1>;
+ label = "lan2";
+ };
+
+ port@2 {
+ reg = <2>;
+ label = "lan3";
+ };
+
+ port@3 {
+ reg = <3>;
+ label = "lan4";
+ };
+
+ port@4 {
+ reg = <4>;
+ label = "lan5";
+ };
+
+ port@5 {
+ reg = <5>;
+ label = "cpu";
+ };
+
+ port@6 {
+ /* 88E1512 external phy */
+ reg = <6>;
+ label = "lan6";
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+ };
+ };
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ pinctrl-0 = <&rear_button_pins>;
+ pinctrl-names = "default";
+
+ button_0 {
+ /* The rear SW3 button */
+ label = "Rear Button";
+ gpios = <&gpio1 2 GPIO_ACTIVE_LOW>;
+ linux,can-disable;
+ linux,code = <BTN_0>;
+ };
+ };
+};
+
+/*
++#define A38x_CUSTOMER_BOARD_1_MPP16_23 0x00400011
+MPP18: gpio ? (pca9655 int?)
+MPP19: gpio ? (clkreq?)
+MPP20: gpio ? (sd0 detect)
+MPP21: sd0:cmd x sd0
+MPP22: gpio x mikro int
+MPP23: gpio x switch irq
++#define A38x_CUSTOMER_BOARD_1_MPP24_31 0x22043333
+MPP24: ua1:rxd x mikro rx
+MPP25: ua1:txd x mikro tx
+MPP26: i2c1:sck x mikro sck
+MPP27: i2c1:sda x mikro sda
+MPP28: sd0:clk x sd0
+MPP29: gpio x mikro rst
+MPP30: ge1:txd2 ? (config)
+MPP31: ge1:txd3 ? (config)
++#define A38x_CUSTOMER_BOARD_1_MPP32_39 0x44400002
+MPP32: ge1:txctl ? (unused)
+MPP33: gpio ? (pic_com0)
+MPP34: gpio x rear button (pic_com1)
+MPP35: gpio ? (pic_com2)
+MPP36: gpio ? (unused)
+MPP37: sd0:d3 x sd0
+MPP38: sd0:d0 x sd0
+MPP39: sd0:d1 x sd0
++#define A38x_CUSTOMER_BOARD_1_MPP40_47 0x41144004
+MPP40: sd0:d2 x sd0
+MPP41: gpio x switch reset
+MPP42: gpio ? sw1-1
+MPP43: spi1:cs2 x mikro cs
+MPP44: sata3:prsnt ? (unused)
+MPP45: ref:clk_out0 ?
+MPP46: ref:clk_out1 x switch clk
+MPP47: 4 ? (unused)
++#define A38x_CUSTOMER_BOARD_1_MPP48_55 0x40333333
+MPP48: tdm:pclk
+MPP49: tdm:fsync
+MPP50: tdm:drx
+MPP51: tdm:dtx
+MPP52: tdm:int
+MPP53: tdm:rst
+MPP54: gpio ? (pwm)
+MPP55: spi1:cs1 x slic
++#define A38x_CUSTOMER_BOARD_1_MPP56_63 0x00004444
+MPP56: spi1:mosi x mikro mosi
+MPP57: spi1:sck x mikro sck
+MPP58: spi1:miso x mikro miso
+MPP59: spi1:cs0 x w25q32
+*/
prompt "Marvell MVEBU (Armada XP/38x) board select"
optional
+config TARGET_CLEARFOG
+ bool "Support ClearFog"
+
config TARGET_DB_88F6820_GP
bool "Support DB-88F6820-GP"
--- /dev/null
+if TARGET_CLEARFOG
+
+config SYS_BOARD
+ default "clearfog"
+
+config SYS_VENDOR
+ default "solidrun"
+
+config SYS_CONFIG_NAME
+ default "clearfog"
+
+endif
--- /dev/null
+CLEARFOG BOARD
+M: Stefan Roese <sr@denx.de>
+S: Maintained
+F: board/soldrun/clearfog/
+F: include/configs/clearfog.h
+F: configs/clearfog_defconfig
--- /dev/null
+#
+# Copyright (C) 2015 Stefan Roese <sr@denx.de>
+#
+# SPDX-License-Identifier: GPL-2.0+
+#
+
+obj-y := clearfog.o
--- /dev/null
+Update from original Marvell U-Boot to mainline U-Boot:
+-------------------------------------------------------
+
+Generate the U-Boot image with these commands:
+
+$ make clearfog_defconfig
+$ make
+
+The resulting image including the SPL binary with the
+full DDR setup is "u-boot-spl.kwb".
+
+Now all you need to do is copy this image on a SD card.
+For example with this command:
+
+$ sudo dd if=u-boot-spl.kwb of=/dev/sdX bs=512 seek=1
+
+Please use the correct device node for your setup instead
+of "/dev/sdX" here!
--- /dev/null
+/*
+ * Copyright (C) 2015 Stefan Roese <sr@denx.de>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <i2c.h>
+#include <miiphy.h>
+#include <netdev.h>
+#include <asm/io.h>
+#include <asm/arch/cpu.h>
+#include <asm/arch/soc.h>
+
+#include "../drivers/ddr/marvell/a38x/ddr3_a38x_topology.h"
+#include <../serdes/a38x/high_speed_env_spec.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#define ETH_PHY_CTRL_REG 0
+#define ETH_PHY_CTRL_POWER_DOWN_BIT 11
+#define ETH_PHY_CTRL_POWER_DOWN_MASK (1 << ETH_PHY_CTRL_POWER_DOWN_BIT)
+
+/*
+ * Those values and defines are taken from the Marvell U-Boot version
+ * "u-boot-2013.01-15t1-clearfog"
+ */
+#define BOARD_GPP_OUT_ENA_LOW 0xffffffff
+#define BOARD_GPP_OUT_ENA_MID 0xffffffff
+
+#define BOARD_GPP_OUT_VAL_LOW 0x0
+#define BOARD_GPP_OUT_VAL_MID 0x0
+#define BOARD_GPP_POL_LOW 0x0
+#define BOARD_GPP_POL_MID 0x0
+
+/* IO expander on Marvell GP board includes e.g. fan enabling */
+struct marvell_io_exp {
+ u8 chip;
+ u8 addr;
+ u8 val;
+};
+
+static struct marvell_io_exp io_exp[] = {
+ { 0x20, 2, 0x40 }, /* Deassert both mini pcie reset signals */
+ { 0x20, 6, 0xf9 },
+ { 0x20, 2, 0x46 }, /* rst signals and ena USB3 current limiter */
+ { 0x20, 6, 0xb9 },
+ { 0x20, 3, 0x00 }, /* Set SFP_TX_DIS to zero */
+ { 0x20, 7, 0xbf }, /* Drive SFP_TX_DIS to zero */
+};
+
+static struct serdes_map board_serdes_map[] = {
+ {SATA0, SERDES_SPEED_3_GBPS, SERDES_DEFAULT_MODE, 0, 0},
+ {SGMII1, SERDES_SPEED_1_25_GBPS, SERDES_DEFAULT_MODE, 0, 0},
+ {PEX1, SERDES_SPEED_5_GBPS, PEX_ROOT_COMPLEX_X1, 0, 0},
+ {USB3_HOST1, SERDES_SPEED_5_GBPS, SERDES_DEFAULT_MODE, 0, 0},
+ {PEX2, SERDES_SPEED_5_GBPS, PEX_ROOT_COMPLEX_X1, 0, 0},
+ {SGMII2, SERDES_SPEED_1_25_GBPS, SERDES_DEFAULT_MODE, 0, 0},
+};
+
+int hws_board_topology_load(struct serdes_map **serdes_map_array, u8 *count)
+{
+ *serdes_map_array = board_serdes_map;
+ *count = ARRAY_SIZE(board_serdes_map);
+ return 0;
+}
+
+/*
+ * Define the DDR layout / topology here in the board file. This will
+ * be used by the DDR3 init code in the SPL U-Boot version to configure
+ * the DDR3 controller.
+ */
+static struct hws_topology_map board_topology_map = {
+ 0x1, /* active interfaces */
+ /* cs_mask, mirror, dqs_swap, ck_swap X PUPs */
+ { { { {0x1, 0, 0, 0},
+ {0x1, 0, 0, 0},
+ {0x1, 0, 0, 0},
+ {0x1, 0, 0, 0},
+ {0x1, 0, 0, 0} },
+ SPEED_BIN_DDR_1600K, /* speed_bin */
+ BUS_WIDTH_16, /* memory_width */
+ MEM_4G, /* mem_size */
+ DDR_FREQ_800, /* frequency */
+ 0, 0, /* cas_l cas_wl */
+ HWS_TEMP_LOW} }, /* temperature */
+ 5, /* Num Of Bus Per Interface*/
+ BUS_MASK_32BIT /* Busses mask */
+};
+
+struct hws_topology_map *ddr3_get_topology_map(void)
+{
+ /* Return the board topology as defined in the board code */
+ return &board_topology_map;
+}
+
+int board_early_init_f(void)
+{
+ /* Configure MPP */
+ writel(0x11111111, MVEBU_MPP_BASE + 0x00);
+ writel(0x11111111, MVEBU_MPP_BASE + 0x04);
+ writel(0x10400011, MVEBU_MPP_BASE + 0x08);
+ writel(0x22043333, MVEBU_MPP_BASE + 0x0c);
+ writel(0x44400002, MVEBU_MPP_BASE + 0x10);
+ writel(0x41144004, MVEBU_MPP_BASE + 0x14);
+ writel(0x40333333, MVEBU_MPP_BASE + 0x18);
+ writel(0x00004444, MVEBU_MPP_BASE + 0x1c);
+
+ /* Set GPP Out value */
+ writel(BOARD_GPP_OUT_VAL_LOW, MVEBU_GPIO0_BASE + 0x00);
+ writel(BOARD_GPP_OUT_VAL_MID, MVEBU_GPIO1_BASE + 0x00);
+
+ /* Set GPP Polarity */
+ writel(BOARD_GPP_POL_LOW, MVEBU_GPIO0_BASE + 0x0c);
+ writel(BOARD_GPP_POL_MID, MVEBU_GPIO1_BASE + 0x0c);
+
+ /* Set GPP Out Enable */
+ writel(BOARD_GPP_OUT_ENA_LOW, MVEBU_GPIO0_BASE + 0x04);
+ writel(BOARD_GPP_OUT_ENA_MID, MVEBU_GPIO1_BASE + 0x04);
+
+ return 0;
+}
+
+int board_init(void)
+{
+ int i;
+
+ /* Address of boot parameters */
+ gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100;
+
+ /* Toggle GPIO41 to reset onboard switch and phy */
+ clrbits_le32(MVEBU_GPIO1_BASE + 0x0, BIT(9));
+ clrbits_le32(MVEBU_GPIO1_BASE + 0x4, BIT(9));
+ mdelay(1);
+ setbits_le32(MVEBU_GPIO1_BASE + 0x0, BIT(9));
+ mdelay(10);
+
+ /* Init I2C IO expanders */
+ for (i = 0; i < ARRAY_SIZE(io_exp); i++)
+ i2c_write(io_exp[i].chip, io_exp[i].addr, 1, &io_exp[i].val, 1);
+
+ return 0;
+}
+
+int checkboard(void)
+{
+ puts("Board: SolidRun ClearFog\n");
+
+ return 0;
+}
+
+int board_eth_init(bd_t *bis)
+{
+ cpu_eth_init(bis); /* Built in controller(s) come first */
+ return pci_eth_init(bis);
+}
--- /dev/null
+#
+# Copyright (C) 2015 Stefan Roese <sr@denx.de>
+#
+
+# Armada XP uses version 1 image format
+VERSION 1
+
+# Boot Media configurations
+BOOT_FROM sdio
+
+# Binary Header (bin_hdr) with DDR3 training code
+BINARY spl/u-boot-spl-dtb.bin 0000005b 00000068
--- /dev/null
+CONFIG_ARM=y
+CONFIG_ARCH_MVEBU=y
+CONFIG_SYS_MALLOC_F_LEN=0x2000
+CONFIG_TARGET_CLEARFOG=y
+CONFIG_DEFAULT_DEVICE_TREE="armada-388-clearfog"
+CONFIG_SPL=y
+# CONFIG_CMD_IMLS is not set
+# CONFIG_CMD_FLASH is not set
+CONFIG_CMD_USB=y
+# CONFIG_CMD_SETEXPR is not set
+CONFIG_SPL_OF_TRANSLATE=y
+CONFIG_SPI_FLASH=y
+CONFIG_DEBUG_UART=y
+CONFIG_DEBUG_UART_BASE=0xd0012000
+CONFIG_DEBUG_UART_CLOCK=250000000
+CONFIG_DEBUG_UART_SHIFT=2
+CONFIG_SYS_NS16550=y
+CONFIG_USB=y
+CONFIG_DM_USB=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_STORAGE=y
--- /dev/null
+/*
+ * Copyright (C) 2015 Stefan Roese <sr@denx.de>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef _CONFIG_CLEARFOG_H
+#define _CONFIG_CLEARFOG_H
+
+/*
+ * High Level Configuration Options (easy to change)
+ */
+#define CONFIG_ARMADA_XP /* SOC Family Name */
+#define CONFIG_ARMADA_38X
+#define CONFIG_DB_88F6820_GP /* Board target name for DDR training */
+
+#define CONFIG_DISPLAY_BOARDINFO_LATE
+
+/*
+ * TEXT_BASE needs to be below 16MiB, since this area is scrubbed
+ * for DDR ECC byte filling in the SPL before loading the main
+ * U-Boot into it.
+ */
+#define CONFIG_SYS_TEXT_BASE 0x00800000
+#define CONFIG_SYS_TCLK 250000000 /* 250MHz */
+
+/*
+ * Commands configuration
+ */
+#define CONFIG_SYS_NO_FLASH /* Declare no flash (NOR/SPI) */
+#define CONFIG_CMD_BOOTZ
+#define CONFIG_CMD_CACHE
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_ENV
+#define CONFIG_CMD_EXT2
+#define CONFIG_CMD_EXT4
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_FS_GENERIC
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_MMC
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_SF
+#define CONFIG_CMD_SPI
+#define CONFIG_CMD_TFTPPUT
+#define CONFIG_CMD_TIME
+
+/* I2C */
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_MVTWSI
+#define CONFIG_I2C_MVTWSI_BASE0 MVEBU_TWSI_BASE
+#define CONFIG_SYS_I2C_SLAVE 0x0
+#define CONFIG_SYS_I2C_SPEED 100000
+
+/* SPI NOR flash default params, used by sf commands */
+#define CONFIG_SF_DEFAULT_SPEED 1000000
+#define CONFIG_SF_DEFAULT_MODE SPI_MODE_3
+#define CONFIG_SPI_FLASH_STMICRO
+
+/*
+ * SDIO/MMC Card Configuration
+ */
+#define CONFIG_MMC
+#define CONFIG_MMC_SDMA
+#define CONFIG_GENERIC_MMC
+#define CONFIG_SDHCI
+#define CONFIG_MV_SDHCI
+#define CONFIG_SYS_MMC_BASE MVEBU_SDIO_BASE
+
+/* Partition support */
+#define CONFIG_DOS_PARTITION
+#define CONFIG_EFI_PARTITION
+
+/* Additional FS support/configuration */
+#define CONFIG_SUPPORT_VFAT
+
+/* USB/EHCI configuration */
+#define CONFIG_EHCI_IS_TDI
+
+#define CONFIG_ENV_MIN_ENTRIES 128
+
+/* Environment in MMC */
+#define CONFIG_ENV_IS_IN_MMC
+#define CONFIG_SYS_MMC_ENV_DEV 0
+#define CONFIG_ENV_SECT_SIZE 0x200
+#define CONFIG_ENV_SIZE 0x10000
+/*
+ * For SD - reserve 1 LBA for MBR + 1M for u-boot image. The MMC/eMMC
+ * boot image starts @ LBA-0.
+ * As result in MMC/eMMC case it will be a 1 sector gap between u-boot
+ * image and environment
+ */
+#define CONFIG_ENV_OFFSET 0xf0000
+#define CONFIG_ENV_ADDR CONFIG_ENV_OFFSET
+
+#define CONFIG_PHY_MARVELL /* there is a marvell phy */
+#define PHY_ANEG_TIMEOUT 8000 /* PHY needs a longer aneg time */
+
+/* PCIe support */
+#ifndef CONFIG_SPL_BUILD
+#define CONFIG_PCI
+#define CONFIG_PCI_MVEBU
+#define CONFIG_PCI_PNP
+#define CONFIG_PCI_SCAN_SHOW
+#endif
+
+#define CONFIG_SYS_CONSOLE_INFO_QUIET /* don't print console @ startup */
+#define CONFIG_SYS_ALT_MEMTEST
+
+/* Keep device tree and initrd in lower memory so the kernel can access them */
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "fdt_high=0x10000000\0" \
+ "initrd_high=0x10000000\0"
+
+/* SPL */
+/*
+ * Select the boot device here
+ *
+ * Currently supported are:
+ * SPL_BOOT_SPI_NOR_FLASH - Booting via SPI NOR flash
+ * SPL_BOOT_SDIO_MMC_CARD - Booting via SDIO/MMC card (partition 1)
+ */
+#define SPL_BOOT_SPI_NOR_FLASH 1
+#define SPL_BOOT_SDIO_MMC_CARD 2
+#define CONFIG_SPL_BOOT_DEVICE SPL_BOOT_SDIO_MMC_CARD
+
+/* Defines for SPL */
+#define CONFIG_SPL_FRAMEWORK
+#define CONFIG_SPL_SIZE (140 << 10)
+#define CONFIG_SPL_TEXT_BASE 0x40000030
+#define CONFIG_SPL_MAX_SIZE (CONFIG_SPL_SIZE - 0x0030)
+
+#define CONFIG_SPL_BSS_START_ADDR (0x40000000 + CONFIG_SPL_SIZE)
+#define CONFIG_SPL_BSS_MAX_SIZE (16 << 10)
+
+#ifdef CONFIG_SPL_BUILD
+#define CONFIG_SYS_MALLOC_SIMPLE
+#endif
+
+#define CONFIG_SPL_STACK (0x40000000 + ((192 - 16) << 10))
+#define CONFIG_SPL_BOOTROM_SAVE (CONFIG_SPL_STACK + 4)
+
+#define CONFIG_SPL_LIBCOMMON_SUPPORT
+#define CONFIG_SPL_LIBGENERIC_SUPPORT
+#define CONFIG_SPL_SERIAL_SUPPORT
+#define CONFIG_SPL_I2C_SUPPORT
+
+#if CONFIG_SPL_BOOT_DEVICE == SPL_BOOT_SPI_NOR_FLASH
+/* SPL related SPI defines */
+#define CONFIG_SPL_SPI_SUPPORT
+#define CONFIG_SPL_SPI_FLASH_SUPPORT
+#define CONFIG_SPL_SPI_LOAD
+#define CONFIG_SPL_SPI_BUS 0
+#define CONFIG_SPL_SPI_CS 0
+#define CONFIG_SYS_SPI_U_BOOT_OFFS 0x20000
+#define CONFIG_SYS_U_BOOT_OFFS CONFIG_SYS_SPI_U_BOOT_OFFS
+#endif
+
+#if CONFIG_SPL_BOOT_DEVICE == SPL_BOOT_SDIO_MMC_CARD
+/* SPL related MMC defines */
+#define CONFIG_SPL_MMC_SUPPORT
+#define CONFIG_SPL_LIBDISK_SUPPORT
+#define CONFIG_SYS_MMC_U_BOOT_OFFS (160 << 10)
+#define CONFIG_SYS_U_BOOT_OFFS CONFIG_SYS_MMC_U_BOOT_OFFS
+#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR ((CONFIG_SYS_U_BOOT_OFFS / 512)\
+ + 1)
+#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS ((512 << 10) / 512) /* 512KiB */
+#ifdef CONFIG_SPL_BUILD
+#define CONFIG_FIXED_SDHCI_ALIGNED_BUFFER 0x00180000 /* in SDRAM */
+#endif
+#endif
+
+/* Enable DDR support in SPL (DDR3 training from Marvell bin_hdr) */
+#define CONFIG_SYS_MVEBU_DDR_A38X
+#define CONFIG_DDR3
+
+/*
+ * mv-common.h should be defined after CMD configs since it used them
+ * to enable certain macros
+ */
+#include "mv-common.h"
+
+#endif /* _CONFIG_CLEARFOG_H */
projects / platform / kernel / u-boot.git / commitdiff