siemens: thuban: Enable DM_SPI, DM_SPI_FLASH
authorJagan Teki <jagan@amarulasolutions.com>
Thu, 9 Jul 2020 07:58:34 +0000 (13:28 +0530)
committerJagan Teki <jagan@amarulasolutions.com>
Thu, 9 Jul 2020 15:28:05 +0000 (20:58 +0530)
Enable DM_SPI, DM_SPI_FLASH for siemens thuban board.

Build is fine, but not tested.

Cc: Samuel Egli <samuel.egli@siemens.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
configs/thuban_defconfig

index 59b99cd..e9629c3 100644 (file)
@@ -7,6 +7,7 @@ CONFIG_SPL_LIBGENERIC_SUPPORT=y
 CONFIG_SYS_MALLOC_F_LEN=0x2000
 CONFIG_ENV_SIZE=0x2000
 CONFIG_SYS_SPI_U_BOOT_OFFS=0x20000
+CONFIG_SPL_DM_SPI=y
 CONFIG_AM33XX=y
 CONFIG_SYS_MPUCLK=300
 CONFIG_TARGET_THUBAN=y
@@ -27,6 +28,7 @@ CONFIG_SYS_CONSOLE_INFO_QUIET=y
 # CONFIG_DISPLAY_BOARDINFO is not set
 CONFIG_ARCH_MISC_INIT=y
 CONFIG_SPL_I2C_SUPPORT=y
+CONFIG_SPL_DM_SPI_FLASH=y
 CONFIG_SPL_SPI_LOAD=y
 CONFIG_SPL_WATCHDOG_SUPPORT=y
 CONFIG_SPL_YMODEM_SUPPORT=y
@@ -43,7 +45,6 @@ CONFIG_CMD_GPIO=y
 CONFIG_CMD_I2C=y
 CONFIG_CMD_MMC=y
 CONFIG_CMD_NAND=y
-CONFIG_CMD_SF=y
 CONFIG_CMD_USB=y
 # CONFIG_CMD_SETEXPR is not set
 CONFIG_CMD_DHCP=y
@@ -59,24 +60,27 @@ CONFIG_MTDPARTS_DEFAULT="mtdparts=omap2-nand.0:128k(spl),128k(spl.backup1),128k(
 CONFIG_CMD_UBI=y
 # CONFIG_DOS_PARTITION is not set
 CONFIG_OF_CONTROL=y
+CONFIG_SPL_OF_CONTROL=y
 CONFIG_OF_EMBED=y
 CONFIG_DEFAULT_DEVICE_TREE="am335x-draco"
 CONFIG_ENV_IS_IN_NAND=y
 CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
 CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_SPL_DM=y
 CONFIG_BOOTCOUNT_LIMIT=y
 CONFIG_BOOTCOUNT_ENV=y
 CONFIG_DFU_NAND=y
 CONFIG_MMC_OMAP_HS=y
 CONFIG_MTD=y
 CONFIG_MTD_RAW_NAND=y
-CONFIG_SPI_FLASH=y
+CONFIG_DM_SPI_FLASH=y
 CONFIG_SPI_FLASH_WINBOND=y
 CONFIG_MTD_UBI_FASTMAP=y
 CONFIG_MTD_UBI_FASTMAP_AUTOCONVERT=1
 CONFIG_PHY_SMSC=y
 CONFIG_DRIVER_TI_CPSW=y
 CONFIG_SPI=y
+CONFIG_DM_SPI=y
 CONFIG_OMAP3_SPI=y
 CONFIG_USB=y
 CONFIG_USB_MUSB_HOST=y