CONFIG_SYS_I2C_SOFT_SPEED_4 and CONFIG_SYS_I2C_SOFT_SLAVE_4
for defining speed and slave address
+ - drivers/i2c/fsl_i2c.c:
+ - activate i2c driver with CONFIG_SYS_I2C_FSL
+ define CONFIG_SYS_FSL_I2C_OFFSET for setting the register
+ offset CONFIG_SYS_FSL_I2C_SPEED for the i2c speed and
+ CONFIG_SYS_FSL_I2C_SLAVE for the slave addr of the first
+ bus.
+ - If your board supports a second fsl i2c bus, define
+ CONFIG_SYS_FSL_I2C2_OFFSET for the register offset
+ CONFIG_SYS_FSL_I2C2_SPEED for the speed and
+ CONFIG_SYS_FSL_I2C2_SLAVE for the slave address of the
+ second bus.
+
additional defines:
CONFIG_SYS_NUM_I2C_BUSES
If not defined, then U-Boot uses predefined value for
specified DTT device.
- CONFIG_FSL_I2C
-
- Define this option if you want to use Freescale's I2C driver in
- drivers/i2c/fsl_i2c.c.
-
CONFIG_I2C_MUX
Define this option if you have I2C devices reached over 1 .. n
out_be32(&fbcs->csmr5, CONFIG_SYS_CS5_MASK);
#endif
-#ifdef CONFIG_FSL_I2C
+#ifdef CONFIG_SYS_I2C_FSL
out_8(&gpio->par_i2c, GPIO_PAR_I2C_SCL_SCL | GPIO_PAR_I2C_SDA_SDA);
#endif
gd->bus_clk = gd->arch.flb_clk;
}
-#ifdef CONFIG_FSL_I2C
+#ifdef CONFIG_SYS_I2C_FSL
gd->arch.i2c1_clk = gd->bus_clk;
#endif
out_be32(&fbcs->csmr7, CONFIG_SYS_CS7_MASK);
#endif
-#ifdef CONFIG_FSL_I2C
+#ifdef CONFIG_SYS_I2C_FSL
CONFIG_SYS_I2C_PINMUX_REG &= CONFIG_SYS_I2C_PINMUX_CLR;
CONFIG_SYS_I2C_PINMUX_REG |= CONFIG_SYS_I2C_PINMUX_SET;
#endif
gd->bus_clk = CONFIG_SYS_CLK;
gd->cpu_clk = (gd->bus_clk * 2);
-#ifdef CONFIG_FSL_I2C
+#ifdef CONFIG_SYS_I2C_FSL
gd->arch.i2c1_clk = gd->bus_clk;
#endif
/* FlexBus Chipselect */
init_fbcs();
-#ifdef CONFIG_FSL_I2C
+#ifdef CONFIG_SYS_I2C_FSL
CONFIG_SYS_I2C_PINMUX_REG =
CONFIG_SYS_I2C_PINMUX_REG & CONFIG_SYS_I2C_PINMUX_CLR;
CONFIG_SYS_I2C_PINMUX_REG |= CONFIG_SYS_I2C_PINMUX_SET;
init_fbcs();
#endif /* #ifndef CONFIG_MONITOR_IS_IN_RAM */
-#ifdef CONFIG_FSL_I2C
+#ifdef CONFIG_SYS_I2C_FSL
CONFIG_SYS_I2C_PINMUX_REG &= CONFIG_SYS_I2C_PINMUX_CLR;
CONFIG_SYS_I2C_PINMUX_REG |= CONFIG_SYS_I2C_PINMUX_SET;
#endif
gd->bus_clk = gd->cpu_clk;
#endif
-#ifdef CONFIG_FSL_I2C
+#ifdef CONFIG_SYS_I2C_FSL
gd->arch.i2c1_clk = gd->bus_clk;
-#ifdef CONFIG_SYS_I2C2_OFFSET
+#ifdef CONFIG_SYS_I2C2_FSL_OFFSET
gd->arch.i2c2_clk = gd->bus_clk;
#endif
#endif
out_be32(&fbcs->csmr5, CONFIG_SYS_CS5_MASK);
#endif
-#ifdef CONFIG_FSL_I2C
+#ifdef CONFIG_SYS_I2C_FSL
out_8(&gpio->par_feci2c,
GPIO_PAR_FECI2C_SDA_SDA | GPIO_PAR_FECI2C_SCL_SCL);
#endif
out_be32(&fbcs->csmr5, CONFIG_SYS_CS5_MASK);
#endif
-#ifdef CONFIG_FSL_I2C
+#ifdef CONFIG_SYS_I2C_FSL
out_8(&gpio->par_feci2c,
GPIO_PAR_FECI2C_SCL_SCL | GPIO_PAR_FECI2C_SDA_SDA);
#endif
gd->bus_clk = clock_pll(CONFIG_SYS_CLK / 1000, 0) * 1000;
gd->cpu_clk = (gd->bus_clk * 3);
-#ifdef CONFIG_FSL_I2C
+#ifdef CONFIG_SYS_I2C_FSL
gd->arch.i2c1_clk = gd->bus_clk;
#endif
GPIO_PAR_FBCTL_OE | GPIO_PAR_FBCTL_TA_TA |
GPIO_PAR_FBCTL_RW_RW | GPIO_PAR_FBCTL_TS_TS);
-#ifdef CONFIG_FSL_I2C
+#ifdef CONFIG_SYS_FSL_I2C
out_be16(&gpio->par_feci2c,
GPIO_PAR_FECI2C_SCL_SCL | GPIO_PAR_FECI2C_SDA_SDA);
#endif
#endif
}
-#ifdef CONFIG_FSL_I2C
+#ifdef CONFIG_SYS_I2C_FSL
gd->arch.i2c1_clk = gd->bus_clk;
#endif
}
setup_5445x_clocks();
#endif
-#ifdef CONFIG_FSL_I2C
+#ifdef CONFIG_SYS_FSL_I2C
gd->arch.i2c1_clk = gd->bus_clk;
#endif
out_be32(&fbcs->csmr5, CONFIG_SYS_CS5_MASK);
#endif
-#ifdef CONFIG_FSL_I2C
+#ifdef CONFIG_SYS_I2C_FSL
out_be16(&gpio->par_feci2cirq,
GPIO_PAR_FECI2CIRQ_SCL | GPIO_PAR_FECI2CIRQ_SDA);
#endif
gd->bus_clk = CONFIG_SYS_CLK;
gd->cpu_clk = (gd->bus_clk * 2);
-#ifdef CONFIG_FSL_I2C
+#ifdef CONFIG_SYS_I2C_FSL
gd->arch.i2c1_clk = gd->bus_clk;
#endif
/* Architecture-specific global data */
struct arch_global_data {
-#ifdef CONFIG_FSL_I2C
+#ifdef CONFIG_SYS_I2C_FSL
unsigned long i2c1_clk;
unsigned long i2c2_clk;
#endif
int vme8349_read_spd(uchar chip, uint addr, int alen, uchar *buffer, int len)
{
- int old_bus = I2C_GET_BUS();
+ int old_bus = i2c_get_bus_num();
unsigned int l, sum;
int valid = 0;
- I2C_SET_BUS(0);
+ i2c_set_bus_num(0);
if (i2c_read(chip, addr, alen, buffer, len) == 0)
if (memcmp(&buffer[64], &default_spd_eeprom.mid[0], 8) == 0) {
buffer[63] = sum;
}
- I2C_SET_BUS(old_bus);
+ i2c_set_bus_num(old_bus);
return 0;
}
CONFIG_MCFTMR -- define to use DMA timer
CONFIG_MCFPIT -- define to use PIT timer
-CONFIG_FSL_I2C -- define to use FSL common I2C driver
+CONFIG_SYS_I2C_FSL -- define to use FSL common I2C driver
CONFIG_HARD_I2C -- define for I2C hardware support
CONFIG_SYS_I2C_SOFT -- define for I2C bit-banged
CONFIG_SYS_I2C_SPEED -- define for I2C speed
CONFIG_MCFTMR -- define to use DMA timer
CONFIG_MCFPIT -- define to use PIT timer
-CONFIG_FSL_I2C -- define to use FSL common I2C driver
+CONFIG_SYS_I2C_FSL -- define to use FSL common I2C driver
CONFIG_HARD_I2C -- define for I2C hardware support
CONFIG_SYS_I2C_SOFT -- define for I2C bit-banged
CONFIG_SYS_I2C_SPEED -- define for I2C speed
CONFIG_MCFTMR -- define to use DMA timer
CONFIG_MCFPIT -- define to use PIT timer
-CONFIG_FSL_I2C -- define to use FSL common I2C driver
+CONFIG_SYS_I2C_FSL -- define to use FSL common I2C driver
CONFIG_HARD_I2C -- define for I2C hardware support
CONFIG_SYS_I2C_SOFT -- define for I2C bit-banged
CONFIG_SYS_I2C_SPEED -- define for I2C speed
CONFIG_MCFTMR -- define to use DMA timer
CONFIG_MCFPIT -- define to use PIT timer
-CONFIG_FSL_I2C -- define to use FSL common I2C driver
+CONFIG_SYS_FSL_I2C -- define to use FSL common I2C driver
CONFIG_HARD_I2C -- define for I2C hardware support
CONFIG_SYS_I2C_SOFT -- define for I2C bit-banged
CONFIG_SYS_I2C_SPEED -- define for I2C speed
CONFIG_SLTTMR -- define to use SLT timer
-CONFIG_FSL_I2C -- define to use FSL common I2C driver
+CONFIG_SYS_I2C_FSL -- define to use FSL common I2C driver
CONFIG_HARD_I2C -- define for I2C hardware support
CONFIG_SYS_I2C_SOFT -- define for I2C bit-banged
CONFIG_SYS_I2C_SPEED -- define for I2C speed
{
int rc = 0;
-#ifdef CONFIG_HARD_I2C
-
+#if defined(CONFIG_SYS_I2C)
unsigned int orig_bus = i2c_get_bus_num();
u8 i2c_data;
#endif
u8 reg8;
-#ifdef CONFIG_HARD_I2C
+#if defined(CONFIG_SYS_I2C)
i2c_set_bus_num(1);
/* Read the PCI_M66EN jumper setting */
if ((i2c_read(CONFIG_SYS_I2C_8574_ADDR2, 0, 0, ®8, sizeof(reg8)) == 0) ||
in_8(&cpld_data->pcba_rev) & 0x0F);
/* Initialize i2c early for rom_loc and flash bank information */
- i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
+ i2c_set_bus_num(CONFIG_SYS_SPD_BUS_NUM);
if (i2c_read(CONFIG_SYS_I2C_PCA9557_ADDR, 0, 1, &in, 1) < 0 ||
i2c_read(CONFIG_SYS_I2C_PCA9557_ADDR, 1, 1, &out, 1) < 0 ||
int ivm_read_eeprom(void)
{
-#if defined(CONFIG_I2C_MUX)
- I2C_MUX_DEVICE *dev = NULL;
-#endif
uchar i2c_buffer[CONFIG_SYS_IVM_EEPROM_MAX_LEN];
char *buf;
unsigned long dev_addr = CONFIG_SYS_IVM_EEPROM_ADR;
int ret;
-#if defined(CONFIG_SYS_I2C)
buf = getenv("EEprom_ivm");
i2c_set_bus_num(buf ? (int)simple_strtol(buf, NULL, 10) : 0);
-#else
-#if defined(CONFIG_I2C_MUX)
- /* First init the Bus, select the Bus */
- buf = (unsigned char *) getenv("EEprom_ivm");
- if (buf != NULL)
- dev = i2c_mux_ident_muxstring(buf);
- if (dev == NULL) {
- printf("Error couldnt add Bus for IVM\n");
- return -1;
- }
- i2c_set_bus_num(dev->busid);
-#endif
/* add deblocking here */
i2c_make_abort();
{0, 0, 0, 0, QE_IOP_TAB_END},
};
-static int board_init_i2c_busses(void)
-{
- I2C_MUX_DEVICE *dev = NULL;
- uchar *dtt_bus = (uchar *)"pca9547:70:a";
-
- /* Set up the Bus for the DTTs */
- dev = i2c_mux_ident_muxstring(dtt_bus);
- if (dev == NULL)
- printf("Error couldn't add Bus for DTT\n");
-
- return 0;
-}
-
#if defined(CONFIG_SUVD3)
const uint upma_table[] = {
0x1ffedc00, 0x0ffcdc80, 0x0ffcdc80, 0x0ffcdc04, /* Words 0 to 3 */
int misc_init_r(void)
{
- /* add board specific i2c busses */
- board_init_i2c_busses();
return 0;
}
COBJS-$(CONFIG_BFIN_TWI_I2C) += bfin-twi_i2c.o
COBJS-$(CONFIG_DRIVER_DAVINCI_I2C) += davinci_i2c.o
COBJS-$(CONFIG_DW_I2C) += designware_i2c.o
-COBJS-$(CONFIG_FSL_I2C) += fsl_i2c.o
COBJS-$(CONFIG_I2C_MVTWSI) += mvtwsi.o
COBJS-$(CONFIG_I2C_MV) += mv_i2c.o
COBJS-$(CONFIG_I2C_MXC) += mxc_i2c.o
COBJS-$(CONFIG_SH_I2C) += sh_i2c.o
COBJS-$(CONFIG_SH_SH7734_I2C) += sh_sh7734_i2c.o
COBJS-$(CONFIG_SYS_I2C) += i2c_core.o
+COBJS-$(CONFIG_SYS_I2C_FSL) += fsl_i2c.o
COBJS-$(CONFIG_SYS_I2C_SOFT) += soft_i2c.o
COBJS-$(CONFIG_ZYNQ_I2C) += zynq_i2c.o
/*
* Copyright 2006,2009 Freescale Semiconductor, Inc.
*
+ * 2012, Heiko Schocher, DENX Software Engineering, hs@denx.de.
+ * Changes for multibus/multiadapter I2C support.
+ *
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License
* Version 2 as published by the Free Software Foundation.
*/
#include <common.h>
-
-#ifdef CONFIG_HARD_I2C
-
#include <command.h>
#include <i2c.h> /* Functional interface */
-
#include <asm/io.h>
#include <asm/fsl_i2c.h> /* HW definitions */
DECLARE_GLOBAL_DATA_PTR;
-/* Initialize the bus pointer to whatever one the SPD EEPROM is on.
- * Default is bus 0. This is necessary because the DDR initialization
- * runs from ROM, and we can't switch buses because we can't modify
- * the global variables.
- */
-#ifndef CONFIG_SYS_SPD_BUS_NUM
-#define CONFIG_SYS_SPD_BUS_NUM 0
-#endif
-static unsigned int i2c_bus_num __attribute__ ((section (".data"))) = CONFIG_SYS_SPD_BUS_NUM;
-#if defined(CONFIG_I2C_MUX)
-static unsigned int i2c_bus_num_mux __attribute__ ((section ("data"))) = 0;
-#endif
-
-static unsigned int i2c_bus_speed[2] = {CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SPEED};
-
static const struct fsl_i2c *i2c_dev[2] = {
- (struct fsl_i2c *) (CONFIG_SYS_IMMR + CONFIG_SYS_I2C_OFFSET),
-#ifdef CONFIG_SYS_I2C2_OFFSET
- (struct fsl_i2c *) (CONFIG_SYS_IMMR + CONFIG_SYS_I2C2_OFFSET)
+ (struct fsl_i2c *)(CONFIG_SYS_IMMR + CONFIG_SYS_FSL_I2C_OFFSET),
+#ifdef CONFIG_SYS_FSL_I2C2_OFFSET
+ (struct fsl_i2c *)(CONFIG_SYS_IMMR + CONFIG_SYS_FSL_I2C2_OFFSET)
#endif
};
return gd->arch.i2c1_clk; /* I2C1 clock */
}
-void
-i2c_init(int speed, int slaveadd)
+static void fsl_i2c_init(struct i2c_adapter *adap, int speed, int slaveadd)
{
const struct fsl_i2c *dev;
- unsigned int temp;
- int bus_num, i;
#ifdef CONFIG_SYS_I2C_INIT_BOARD
/* Call board specific i2c bus reset routine before accessing the
*/
i2c_init_board();
#endif
-#ifdef CONFIG_SYS_I2C2_OFFSET
- bus_num = 2;
-#else
- bus_num = 1;
-#endif
- for (i = 0; i < bus_num; i++) {
- dev = i2c_dev[i];
-
- writeb(0, &dev->cr); /* stop I2C controller */
- udelay(5); /* let it shutdown in peace */
- temp = set_i2c_bus_speed(dev, get_i2c_clock(i), speed);
- if (gd->flags & GD_FLG_RELOC)
- i2c_bus_speed[i] = temp;
- writeb(slaveadd << 1, &dev->adr);/* write slave address */
- writeb(0x0, &dev->sr); /* clear status register */
- writeb(I2C_CR_MEN, &dev->cr); /* start I2C controller */
- }
+ dev = (struct fsl_i2c *)i2c_dev[adap->hwadapnr];
+
+ writeb(0, &dev->cr); /* stop I2C controller */
+ udelay(5); /* let it shutdown in peace */
+ set_i2c_bus_speed(dev, get_i2c_clock(adap->hwadapnr), speed);
+ writeb(slaveadd << 1, &dev->adr);/* write slave address */
+ writeb(0x0, &dev->sr); /* clear status register */
+ writeb(I2C_CR_MEN, &dev->cr); /* start I2C controller */
#ifdef CONFIG_SYS_I2C_BOARD_LATE_INIT
/* Call board specific i2c bus reset routine AFTER the bus has been
}
static int
-i2c_wait4bus(void)
+i2c_wait4bus(struct i2c_adapter *adap)
{
+ struct fsl_i2c *dev = (struct fsl_i2c *)i2c_dev[adap->hwadapnr];
unsigned long long timeval = get_ticks();
const unsigned long long timeout = usec2ticks(CONFIG_I2C_MBB_TIMEOUT);
- while (readb(&i2c_dev[i2c_bus_num]->sr) & I2C_SR_MBB) {
+ while (readb(&dev->sr) & I2C_SR_MBB) {
if ((get_ticks() - timeval) > timeout)
return -1;
}
}
static __inline__ int
-i2c_wait(int write)
+i2c_wait(struct i2c_adapter *adap, int write)
{
u32 csr;
unsigned long long timeval = get_ticks();
const unsigned long long timeout = usec2ticks(CONFIG_I2C_TIMEOUT);
+ struct fsl_i2c *dev = (struct fsl_i2c *)i2c_dev[adap->hwadapnr];
do {
- csr = readb(&i2c_dev[i2c_bus_num]->sr);
+ csr = readb(&dev->sr);
if (!(csr & I2C_SR_MIF))
continue;
/* Read again to allow register to stabilise */
- csr = readb(&i2c_dev[i2c_bus_num]->sr);
+ csr = readb(&dev->sr);
- writeb(0x0, &i2c_dev[i2c_bus_num]->sr);
+ writeb(0x0, &dev->sr);
if (csr & I2C_SR_MAL) {
debug("i2c_wait: MAL\n");
}
static __inline__ int
-i2c_write_addr (u8 dev, u8 dir, int rsta)
+i2c_write_addr(struct i2c_adapter *adap, u8 dev, u8 dir, int rsta)
{
+ struct fsl_i2c *device = (struct fsl_i2c *)i2c_dev[adap->hwadapnr];
+
writeb(I2C_CR_MEN | I2C_CR_MSTA | I2C_CR_MTX
| (rsta ? I2C_CR_RSTA : 0),
- &i2c_dev[i2c_bus_num]->cr);
+ &device->cr);
- writeb((dev << 1) | dir, &i2c_dev[i2c_bus_num]->dr);
+ writeb((dev << 1) | dir, &device->dr);
- if (i2c_wait(I2C_WRITE_BIT) < 0)
+ if (i2c_wait(adap, I2C_WRITE_BIT) < 0)
return 0;
return 1;
}
static __inline__ int
-__i2c_write(u8 *data, int length)
+__i2c_write(struct i2c_adapter *adap, u8 *data, int length)
{
+ struct fsl_i2c *dev = (struct fsl_i2c *)i2c_dev[adap->hwadapnr];
int i;
for (i = 0; i < length; i++) {
- writeb(data[i], &i2c_dev[i2c_bus_num]->dr);
+ writeb(data[i], &dev->dr);
- if (i2c_wait(I2C_WRITE_BIT) < 0)
+ if (i2c_wait(adap, I2C_WRITE_BIT) < 0)
break;
}
}
static __inline__ int
-__i2c_read(u8 *data, int length)
+__i2c_read(struct i2c_adapter *adap, u8 *data, int length)
{
+ struct fsl_i2c *dev = (struct fsl_i2c *)i2c_dev[adap->hwadapnr];
int i;
writeb(I2C_CR_MEN | I2C_CR_MSTA | ((length == 1) ? I2C_CR_TXAK : 0),
- &i2c_dev[i2c_bus_num]->cr);
+ &dev->cr);
/* dummy read */
- readb(&i2c_dev[i2c_bus_num]->dr);
+ readb(&dev->dr);
for (i = 0; i < length; i++) {
- if (i2c_wait(I2C_READ_BIT) < 0)
+ if (i2c_wait(adap, I2C_READ_BIT) < 0)
break;
/* Generate ack on last next to last byte */
if (i == length - 2)
writeb(I2C_CR_MEN | I2C_CR_MSTA | I2C_CR_TXAK,
- &i2c_dev[i2c_bus_num]->cr);
+ &dev->cr);
/* Do not generate stop on last byte */
if (i == length - 1)
writeb(I2C_CR_MEN | I2C_CR_MSTA | I2C_CR_MTX,
- &i2c_dev[i2c_bus_num]->cr);
+ &dev->cr);
- data[i] = readb(&i2c_dev[i2c_bus_num]->dr);
+ data[i] = readb(&dev->dr);
}
return i;
}
-int
-i2c_read(u8 dev, uint addr, int alen, u8 *data, int length)
+static int
+fsl_i2c_read(struct i2c_adapter *adap, u8 dev, uint addr, int alen, u8 *data,
+ int length)
{
+ struct fsl_i2c *device = (struct fsl_i2c *)i2c_dev[adap->hwadapnr];
int i = -1; /* signal error */
u8 *a = (u8*)&addr;
- if (i2c_wait4bus() < 0)
+ if (i2c_wait4bus(adap) < 0)
return -1;
if ((!length || alen > 0)
- && i2c_write_addr(dev, I2C_WRITE_BIT, 0) != 0
- && __i2c_write(&a[4 - alen], alen) == alen)
+ && i2c_write_addr(adap, dev, I2C_WRITE_BIT, 0) != 0
+ && __i2c_write(adap, &a[4 - alen], alen) == alen)
i = 0; /* No error so far */
if (length &&
- i2c_write_addr(dev, I2C_READ_BIT, alen ? 1 : 0) != 0)
- i = __i2c_read(data, length);
+ i2c_write_addr(adap, dev, I2C_READ_BIT, alen ? 1 : 0) != 0)
+ i = __i2c_read(adap, data, length);
- writeb(I2C_CR_MEN, &i2c_dev[i2c_bus_num]->cr);
+ writeb(I2C_CR_MEN, &device->cr);
- if (i2c_wait4bus()) /* Wait until STOP */
+ if (i2c_wait4bus(adap)) /* Wait until STOP */
debug("i2c_read: wait4bus timed out\n");
if (i == length)
return -1;
}
-int
-i2c_write(u8 dev, uint addr, int alen, u8 *data, int length)
+static int
+fsl_i2c_write(struct i2c_adapter *adap, u8 dev, uint addr, int alen,
+ u8 *data, int length)
{
+ struct fsl_i2c *device = (struct fsl_i2c *)i2c_dev[adap->hwadapnr];
int i = -1; /* signal error */
u8 *a = (u8*)&addr;
- if (i2c_wait4bus() >= 0
- && i2c_write_addr(dev, I2C_WRITE_BIT, 0) != 0
- && __i2c_write(&a[4 - alen], alen) == alen) {
- i = __i2c_write(data, length);
+ if (i2c_wait4bus(adap) >= 0 &&
+ i2c_write_addr(adap, dev, I2C_WRITE_BIT, 0) != 0 &&
+ __i2c_write(adap, &a[4 - alen], alen) == alen) {
+ i = __i2c_write(adap, data, length);
}
- writeb(I2C_CR_MEN, &i2c_dev[i2c_bus_num]->cr);
- if (i2c_wait4bus()) /* Wait until STOP */
+ writeb(I2C_CR_MEN, &device->cr);
+ if (i2c_wait4bus(adap)) /* Wait until STOP */
debug("i2c_write: wait4bus timed out\n");
if (i == length)
return -1;
}
-int
-i2c_probe(uchar chip)
+static int
+fsl_i2c_probe(struct i2c_adapter *adap, uchar chip)
{
+ struct fsl_i2c *dev = (struct fsl_i2c *)i2c_dev[adap->hwadapnr];
/* For unknow reason the controller will ACK when
* probing for a slave with the same address, so skip
* it.
*/
- if (chip == (readb(&i2c_dev[i2c_bus_num]->adr) >> 1))
- return -1;
-
- return i2c_read(chip, 0, 0, NULL, 0);
-}
-
-int i2c_set_bus_num(unsigned int bus)
-{
-#if defined(CONFIG_I2C_MUX)
- if (bus < CONFIG_SYS_MAX_I2C_BUS) {
- i2c_bus_num = bus;
- } else {
- int ret;
-
- ret = i2x_mux_select_mux(bus);
- if (ret)
- return ret;
- i2c_bus_num = 0;
- }
- i2c_bus_num_mux = bus;
-#else
-#ifdef CONFIG_SYS_I2C2_OFFSET
- if (bus > 1) {
-#else
- if (bus > 0) {
-#endif
+ if (chip == (readb(&dev->adr) >> 1))
return -1;
- }
- i2c_bus_num = bus;
-#endif
- return 0;
+ return fsl_i2c_read(adap, chip, 0, 0, NULL, 0);
}
-int i2c_set_bus_speed(unsigned int speed)
+static unsigned int fsl_i2c_set_bus_speed(struct i2c_adapter *adap,
+ unsigned int speed)
{
- unsigned int i2c_clk = (i2c_bus_num == 1)
- ? gd->arch.i2c2_clk : gd->arch.i2c1_clk;
+ struct fsl_i2c *dev = (struct fsl_i2c *)i2c_dev[adap->hwadapnr];
- writeb(0, &i2c_dev[i2c_bus_num]->cr); /* stop controller */
- i2c_bus_speed[i2c_bus_num] =
- set_i2c_bus_speed(i2c_dev[i2c_bus_num], i2c_clk, speed);
- writeb(I2C_CR_MEN, &i2c_dev[i2c_bus_num]->cr); /* start controller */
+ writeb(0, &dev->cr); /* stop controller */
+ set_i2c_bus_speed(dev, get_i2c_clock(adap->hwadapnr), speed);
+ writeb(I2C_CR_MEN, &dev->cr); /* start controller */
return 0;
}
-unsigned int i2c_get_bus_num(void)
-{
-#if defined(CONFIG_I2C_MUX)
- return i2c_bus_num_mux;
-#else
- return i2c_bus_num;
+/*
+ * Register fsl i2c adapters
+ */
+U_BOOT_I2C_ADAP_COMPLETE(fsl_0, fsl_i2c_init, fsl_i2c_probe, fsl_i2c_read,
+ fsl_i2c_write, fsl_i2c_set_bus_speed,
+ CONFIG_SYS_FSL_I2C_SPEED, CONFIG_SYS_FSL_I2C_SLAVE,
+ 0)
+#ifdef CONFIG_SYS_FSL_I2C2_OFFSET
+U_BOOT_I2C_ADAP_COMPLETE(fsl_1, fsl_i2c_init, fsl_i2c_probe, fsl_i2c_read,
+ fsl_i2c_write, fsl_i2c_set_bus_speed,
+ CONFIG_SYS_FSL_I2C2_SPEED, CONFIG_SYS_FSL_I2C2_SLAVE,
+ 1)
#endif
-}
-
-unsigned int i2c_get_bus_speed(void)
-{
- return i2c_bus_speed[i2c_bus_num];
-}
-
-#endif /* CONFIG_HARD_I2C */
#define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */
/* I2C */
-#define CONFIG_FSL_I2C /* Use FSL common I2C driver */
-#define CONFIG_HARD_I2C /* I2C with hardware support */
-#define CONFIG_I2C_MULTI_BUS
-#define CONFIG_I2C_CMD_TREE
-#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed in Hz */
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-#define CONFIG_SYS_I2C_OFFSET 0x118000
-#define CONFIG_SYS_I2C2_OFFSET 0x119000
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_FSL /* Use FSL common I2C driver */
+#define CONFIG_SYS_FSL_I2C_SPEED 400000 /* I2C speed in Hz */
+#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C2_SPEED 400000 /* I2C speed in Hz */
+#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET 0x118000
+#define CONFIG_SYS_FSL_I2C2_OFFSET 0x119000
/*
* RTC configuration
#define CONFIG_FIT
#define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */
-#define CONFIG_FSL_I2C /* Use FSL common I2C driver */
-#define CONFIG_HARD_I2C /* I2C with hardware support */
-#define CONFIG_I2C_MULTI_BUS
-#define CONFIG_I2C_CMD_TREE
-#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address*/
-#define CONFIG_SYS_I2C_OFFSET 0x3000
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_FSL
+#define CONFIG_SYS_FSL_I2C_SPEED 400000
+#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
/* I2C EEPROM */
#define CONFIG_CMD_EEPROM
#define CONFIG_FIT
#define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */
-#define CONFIG_FSL_I2C /* Use FSL common I2C driver */
-#define CONFIG_HARD_I2C /* I2C with hardware support */
-#undef CONFIG_SOFT_I2C /* I2C bit-banged */
-#define CONFIG_I2C_MULTI_BUS
-#define CONFIG_I2C_CMD_TREE
-#define CONFIG_SYS_I2C_SPEED 400800 /* I2C speed and slave address*/
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-#define CONFIG_SYS_I2C_OFFSET 0x3000
-#define CONFIG_SYS_I2C2_OFFSET 0x3100
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_FSL
+#define CONFIG_SYS_FSL_I2C_SPEED 400800 /* I2C speed and slave address*/
+#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C2_SPEED 400800 /* I2C speed and slave address*/
+#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
+#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
/* I2C EEPROM */
#define CONFIG_ID_EEPROM
/* -------------------------------------------------------------------- */
/* Generic FreeScale hardware I2C support */
-#define CONFIG_HARD_I2C
-#define CONFIG_FSL_I2C
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_FSL
+#define CONFIG_SYS_FSL_I2C_SPEED 400000
+#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
+#define CONFIG_SYS_FSL_I2C2_SPEED 400000
+#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
+#define CONFIG_SYS_I2C_NOPROBES { {0, 0x29} }
#define CONFIG_CMD_I2C
-#define CONFIG_I2C_MULTI_BUS
-#define CONFIG_SYS_I2C_OFFSET 0x3000
-#define CONFIG_SYS_I2C2_OFFSET 0x3100
-
-/* I2C bus configuration */
-#define CONFIG_SYS_I2C_SPEED 400000
-#define CONFIG_SYS_I2C_SLAVE 0x7F
/* DDR2 SO-RDIMM SPD EEPROM is at I2C0-0x51 */
#define CONFIG_SYS_SPD_BUS_NUM 0
#undef CONFIG_MCFPIT
/* I2C */
-#define CONFIG_FSL_I2C
-#define CONFIG_HARD_I2C /* I2C with hw support */
-#define CONFIG_SYS_I2C_SPEED 80000
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-#define CONFIG_SYS_I2C_OFFSET 0x58000
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_FSL
+#define CONFIG_SYS_FSL_I2C_SPEED 80000
+#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET 0x58000
#define CONFIG_SYS_IMMR CONFIG_SYS_MBAR
#define CONFIG_BOOTDELAY 1 /* autoboot after 5 seconds */
#undef CONFIG_MCFPIT
/* I2c */
-#define CONFIG_FSL_I2C
-#define CONFIG_HARD_I2C /* I2C with hardware support */
-#define CONFIG_SYS_I2C_SPEED 80000 /* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-#define CONFIG_SYS_I2C_OFFSET 0x58000
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_FSL
+#define CONFIG_SYS_FSL_I2C_SPEED 80000
+#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET 0x58000
#define CONFIG_SYS_IMMR CONFIG_SYS_MBAR
/* DSPI and Serial Flash */
#undef CONFIG_MCFPIT
/* I2C */
-#define CONFIG_FSL_I2C
-#define CONFIG_HARD_I2C /* I2C with hw support */
-#define CONFIG_SYS_I2C_SPEED 80000
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-#define CONFIG_SYS_I2C_OFFSET 0x00000300
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_i2C_FSL
+#define CONFIG_SYS_FSL_I2C_SPEED 80000
+#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET 0x00000300
#define CONFIG_SYS_IMMR CONFIG_SYS_MBAR
#define CONFIG_SYS_I2C_PINMUX_REG (gpio->par_qspi)
#define CONFIG_SYS_I2C_PINMUX_CLR ~(GPIO_PAR_FECI2C_SCL_MASK | GPIO_PAR_FECI2C_SDA_MASK)
#define CONFIG_HOSTNAME M5253DEMO
/* I2C */
-#define CONFIG_FSL_I2C
-#define CONFIG_HARD_I2C /* I2C with hw support */
-#define CONFIG_SYS_I2C_SPEED 80000
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-#define CONFIG_SYS_I2C_OFFSET 0x00000280
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_FSL
+#define CONFIG_SYS_FSL_I2C_SPEED 80000
+#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET 0x00000280
#define CONFIG_SYS_IMMR CONFIG_SYS_MBAR
#define CONFIG_SYS_I2C_PINMUX_REG (*(u32 *) (CONFIG_SYS_MBAR+0x19C))
#define CONFIG_SYS_I2C_PINMUX_CLR (0xFFFFE7FF)
#endif
/* I2C */
-#define CONFIG_FSL_I2C
-#define CONFIG_HARD_I2C /* I2C with hw support */
-#define CONFIG_SYS_I2C_SPEED 80000
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-#define CONFIG_SYS_I2C_OFFSET 0x00000300
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_FSL
+#define CONFIG_SYS_FSL_I2C_SPEED 80000
+#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET 0x00000300
#define CONFIG_SYS_IMMR CONFIG_SYS_MBAR
#define CONFIG_BOOTDELAY 1 /* autoboot after 1 seconds */
#endif
/* I2C */
-#define CONFIG_FSL_I2C
-#define CONFIG_HARD_I2C /* I2C with hw support */
-#define CONFIG_SYS_I2C_SPEED 80000
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-#define CONFIG_SYS_I2C_OFFSET 0x00000300
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_FSL
+#define CONFIG_SYS_FSL_I2C_SPEED 80000
+#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET 0x00000300
#define CONFIG_SYS_IMMR CONFIG_SYS_MBAR
#define CONFIG_SYS_I2C_PINMUX_REG (gpio_reg->par_feci2c)
#define CONFIG_SYS_I2C_PINMUX_CLR (0xFFF0)
#undef CONFIG_MCFPIT
/* I2C */
-#define CONFIG_FSL_I2C
-#define CONFIG_HARD_I2C /* I2C with hw support */
-#define CONFIG_SYS_I2C_SPEED 80000
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-#define CONFIG_SYS_I2C_OFFSET 0x58000
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_FSL
+#define CONFIG_SYS_FSL_I2C_SPEED 80000
+#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET 0x58000
#define CONFIG_SYS_IMMR CONFIG_SYS_MBAR
#define CONFIG_BOOTDELAY 1 /* autoboot after 5 seconds */
#undef CONFIG_MCFPIT
/* I2C */
-#define CONFIG_FSL_I2C
-#define CONFIG_HARD_I2C /* I2C with hw support */
-#define CONFIG_SYS_I2C_SPEED 80000
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-#define CONFIG_SYS_I2C_OFFSET 0x58000
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_FSL
+#define CONFIG_SYS_FSL_I2C_SPEED 80000
+#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET 0x58000
#define CONFIG_SYS_IMMR CONFIG_SYS_MBAR
#define CONFIG_BOOTDELAY 1 /* autoboot after 5 seconds */
#undef CONFIG_MCFPIT
/* I2C */
-#define CONFIG_FSL_I2C
-#define CONFIG_HARD_I2C /* I2C with hw support */
-#define CONFIG_SYS_I2C_SPEED 80000
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-#define CONFIG_SYS_I2C_OFFSET 0x58000
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_FSL
+#define CONFIG_SYS_FSL_I2C_SPEED 80000
+#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET 0x58000
#define CONFIG_SYS_IMMR CONFIG_SYS_MBAR
#define CONFIG_BOOTDELAY 1 /* autoboot after 5 seconds */
#undef CONFIG_MCFPIT
/* I2c */
-#undef CONFIG_FSL_I2C
+#undef CONFIG_SYS_FSL_I2C
#undef CONFIG_HARD_I2C /* I2C with hardware support */
#undef CONFIG_SYS_I2C_SOFT /* I2C bit-banged */
/* I2C speed and slave address */
#undef CONFIG_MCFPIT
/* I2c */
-#define CONFIG_FSL_I2C
-#define CONFIG_HARD_I2C /* I2C with hardware support */
-#define CONFIG_SYS_I2C_SPEED 80000 /* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-#define CONFIG_SYS_I2C_OFFSET 0x58000
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_FSL
+#define CONFIG_SYS_FSL_I2C_SPEED 80000
+#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET 0x58000
#define CONFIG_SYS_IMMR CONFIG_SYS_MBAR
/* DSPI and Serial Flash */
#undef CONFIG_MCFPIT
/* I2c */
-#define CONFIG_FSL_I2C
-#define CONFIG_HARD_I2C /* I2C with hardware support */
-#define CONFIG_SYS_I2C_SPEED 80000 /* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-#define CONFIG_SYS_I2C_OFFSET 0x58000
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_FSL
+#define CONFIG_SYS_FSL_I2C_SPEED 80000
+#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
+#define CONFIG_SYS_FSLI2C_OFFSET 0x58000
#define CONFIG_SYS_IMMR CONFIG_SYS_MBAR
/* DSPI and Serial Flash */
#endif
/* I2C */
-#define CONFIG_FSL_I2C
-#define CONFIG_HARD_I2C /* I2C with hw support */
-#define CONFIG_SYS_I2C_SPEED 80000
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-#define CONFIG_SYS_I2C_OFFSET 0x00008F00
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_FSL
+#define CONFIG_SYS_FSL_I2C_SPEED 80000
+#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET 0x00008F00
#define CONFIG_SYS_IMMR CONFIG_SYS_MBAR
/* PCI */
#endif
/* I2C */
-#define CONFIG_FSL_I2C
-#define CONFIG_HARD_I2C /* I2C with hw support */
-#define CONFIG_SYS_I2C_SPEED 80000
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-#define CONFIG_SYS_I2C_OFFSET 0x00008F00
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_FSL
+#define CONFIG_SYS_FSL_I2C_SPEED 80000
+#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET 0x00008F00
#define CONFIG_SYS_IMMR CONFIG_SYS_MBAR
/* PCI */
#define CONFIG_OF_STDOUT_VIA_ALIAS 1
/* I2C */
-#define CONFIG_HARD_I2C
-#define CONFIG_FSL_I2C
-#define CONFIG_I2C_MULTI_BUS
-#define CONFIG_SYS_I2C_SPEED 120000
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-#define CONFIG_SYS_I2C_OFFSET 0x3000
-#define CONFIG_SYS_I2C2_OFFSET 0x3100
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_FSL
+#define CONFIG_SYS_FSL_I2C_SPEED 400000
+#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
+#define CONFIG_SYS_FSL_I2C2_SPEED 400000
+#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
/*
* General PCI
#define CONFIG_OF_STDOUT_VIA_ALIAS 1
/* I2C */
-#define CONFIG_HARD_I2C /* I2C with hardware support */
-#define CONFIG_FSL_I2C
-#define CONFIG_I2C_MULTI_BUS
-#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-#define CONFIG_SYS_I2C_NOPROBES { {0, 0x51} } /* Don't probe these addrs */
-#define CONFIG_SYS_I2C_OFFSET 0x3000
-#define CONFIG_SYS_I2C2_OFFSET 0x3100
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_FSL
+#define CONFIG_SYS_FSL_I2C_SPEED 400000
+#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
+#define CONFIG_SYS_FSL_I2C2_SPEED 400000
+#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
+#define CONFIG_SYS_I2C_NOPROBES { {0, 0x51} }
/*
* SPI on header J8
#define CONFIG_SYS_HUSH_PARSER
/* I2C */
-#define CONFIG_HARD_I2C /* I2C with hardware support*/
-#define CONFIG_FSL_I2C
-#define CONFIG_I2C_MULTI_BUS
-#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} } /* Don't probe these addrs */
-#define CONFIG_SYS_I2C_OFFSET 0x3000
-#define CONFIG_SYS_I2C2_OFFSET 0x3100
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_FSL
+#define CONFIG_SYS_FSL_I2C_SPEED 400000
+#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
+#define CONFIG_SYS_FSL_I2C2_SPEED 400000
+#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
+#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} }
/*
* General PCI
#define CONFIG_OF_STDOUT_VIA_ALIAS 1
/* I2C */
-#define CONFIG_HARD_I2C /* I2C with hardware support */
-#define CONFIG_FSL_I2C
-#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave addr */
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-#define CONFIG_SYS_I2C_NOPROBES {0x51} /* Don't probe these addrs */
-#define CONFIG_SYS_I2C_OFFSET 0x3000
-#define CONFIG_SYS_I2C2_OFFSET 0x3100
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_FSL
+#define CONFIG_SYS_FSL_I2C_SPEED 400000
+#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
+#define CONFIG_SYS_I2C_NOPROBES { {0, 0x51} }
/*
* Board info - revision and where boot from
#define CONFIG_OF_STDOUT_VIA_ALIAS 1
/* I2C */
-#define CONFIG_HARD_I2C /* I2C with hardware support */
-#define CONFIG_FSL_I2C
-#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-#define CONFIG_SYS_I2C_NOPROBES {0x51} /* Don't probe these addrs */
-#define CONFIG_SYS_I2C_OFFSET 0x3000
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_FSL
+#define CONFIG_SYS_FSL_I2C_SPEED 400000
+#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
+#define CONFIG_SYS_I2C_NOPROBES { {0, 0x51} }
/*
* Config on-board EEPROM
#define CONFIG_OF_STDOUT_VIA_ALIAS 1
/* I2C */
-#define CONFIG_HARD_I2C /* I2C with hardware support */
-#define CONFIG_FSL_I2C
-#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-#define CONFIG_SYS_I2C_NOPROBES {0x51} /* Don't probe these addrs */
-#define CONFIG_SYS_I2C_OFFSET 0x3000
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_FSL
+#define CONFIG_SYS_FSL_I2C_SPEED 400000
+#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
+#define CONFIG_SYS_I2C_NOPROBES { {0, 0x51} }
/*
* Config on-board RTC
#define CONFIG_OF_STDOUT_VIA_ALIAS 1
/* I2C */
-#define CONFIG_HARD_I2C /* I2C with hardware support*/
-#define CONFIG_FSL_I2C
-#define CONFIG_I2C_MULTI_BUS
-#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} } /* Don't probe these addrs */
-#define CONFIG_SYS_I2C_OFFSET 0x3000
-#define CONFIG_SYS_I2C2_OFFSET 0x3100
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_FSL
+#define CONFIG_SYS_FSL_I2C_SPEED 400000
+#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
+#define CONFIG_SYS_FSL_I2C2_SPEED 400000
+#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
+#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} }
/* SPI */
#define CONFIG_MPC8XXX_SPI
#define CONFIG_PCI
#define CONFIG_RTC_DS1337
-#define CONFIG_HARD_I2C
+#define CONFIG_SYS_I2C
#define CONFIG_TSEC_ENET /* TSEC Ethernet support */
/*
*/
/* I2C */
-#ifdef CONFIG_HARD_I2C
+#ifdef CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_FSL
+#define CONFIG_SYS_FSL_I2C_SPEED 400000
+#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
+#define CONFIG_SYS_FSL_I2C2_SPEED 400000
+#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
-#define CONFIG_FSL_I2C
-#define CONFIG_I2C_MULTI_BUS
-#define CONFIG_SYS_I2C_OFFSET 0x3000
-#define CONFIG_SYS_I2C2_OFFSET 0x3100
#define CONFIG_SYS_SPD_BUS_NUM 1 /* The I2C bus for SPD */
#define CONFIG_SYS_RTC_BUS_NUM 1 /* The I2C bus for RTC */
#define CONFIG_SYS_I2C_RTC_ADDR 0x68 /* I2C1, DS1339 RTC*/
#define SPD_EEPROM_ADDRESS 0x51 /* I2C1, DDR */
-#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-
/* Don't probe these addresses: */
#define CONFIG_SYS_I2C_NOPROBES { {1, CONFIG_SYS_I2C_8574_ADDR1}, \
{1, CONFIG_SYS_I2C_8574_ADDR2}, \
#define CONFIG_VERY_BIG_RAM
#define CONFIG_MAX_MEM_MAPPED ((phys_size_t)256 << 20)
-#ifdef CONFIG_HARD_I2C
+#ifdef CONFIG_SYS_I2C
#define CONFIG_SPD_EEPROM /* use SPD EEPROM for DDR setup*/
#endif
#define CONFIG_CMD_PCI
#endif
-#ifdef CONFIG_HARD_I2C
+#ifdef CONFIG_SYS_I2C
#define CONFIG_CMD_I2C
#endif
#define CONFIG_OF_STDOUT_VIA_ALIAS 1
/* I2C */
-#define CONFIG_HARD_I2C /* I2C with hardware support */
-#define CONFIG_FSL_I2C
-#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-#define CONFIG_SYS_I2C_NOPROBES {0x52} /* Don't probe these addrs */
-#define CONFIG_SYS_I2C_OFFSET 0x3000
-#define CONFIG_SYS_I2C2_OFFSET 0x3100
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_FSL
+#define CONFIG_SYS_FSL_I2C_SPEED 400000
+#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
+#define CONFIG_SYS_I2C_NOPROBES { {0, 0x52} }
/*
* Config on-board RTC
#define CONFIG_OF_STDOUT_VIA_ALIAS
/* I2C */
-#define CONFIG_HARD_I2C /* I2C with hardware support */
-#define CONFIG_FSL_I2C
-#define CONFIG_I2C_MULTI_BUS
-#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-#define CONFIG_SYS_I2C_NOPROBES { {0, 0x52} } /* Don't probe these addrs */
-#define CONFIG_SYS_I2C_OFFSET 0x3000
-#define CONFIG_SYS_I2C2_OFFSET 0x3100
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_FSL
+#define CONFIG_SYS_FSL_I2C_SPEED 400000
+#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
+#define CONFIG_SYS_FSL_I2C2_SPEED 400000
+#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
+#define CONFIG_SYS_I2C_NOPROBES { {0, 0x52} }
/*
* General PCI
#define CONFIG_OF_STDOUT_VIA_ALIAS 1
/* I2C */
-#define CONFIG_HARD_I2C /* I2C with hardware support */
-#define CONFIG_FSL_I2C
-#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-#define CONFIG_SYS_I2C_NOPROBES {0x51} /* Don't probe these addrs */
-#define CONFIG_SYS_I2C_OFFSET 0x3000
-#define CONFIG_SYS_I2C2_OFFSET 0x3100
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_FSL
+#define CONFIG_SYS_FSL_I2C_SPEED 400000
+#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
+#define CONFIG_SYS_I2C_NOPROBES { {0, 0x51} }
/*
* Config on-board RTC
#define CONFIG_OF_STDOUT_VIA_ALIAS 1
/* I2C */
-#define CONFIG_HARD_I2C /* I2C with hardware support */
-#define CONFIG_FSL_I2C
-#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-#define CONFIG_SYS_I2C_NOPROBES {0x51} /* Don't probe these addrs */
-#define CONFIG_SYS_I2C_OFFSET 0x3000
-#define CONFIG_SYS_I2C2_OFFSET 0x3100
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_FSL
+#define CONFIG_SYS_FSL_I2C_SPEED 400000
+#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
+#define CONFIG_SYS_I2C_NOPROBES { {0, 0x51} }
/*
* Config on-board RTC
/*
* I2C
*/
-#define CONFIG_FSL_I2C /* Use FSL common I2C driver */
-#define CONFIG_HARD_I2C /* I2C with hardware support */
-#define CONFIG_I2C_MULTI_BUS
-#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-#define CONFIG_SYS_I2C_NOPROBES {{0, 0x29}} /* Don't probe these addrs */
-#define CONFIG_SYS_I2C_OFFSET 0x3000
-#define CONFIG_SYS_I2C2_OFFSET 0x3100
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_FSL
+#define CONFIG_SYS_FSL_I2C_SPEED 400000
+#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
+#define CONFIG_SYS_FSL_I2C2_SPEED 400000
+#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
+#define CONFIG_SYS_I2C_NOPROBES { {0, 0x29} }
/*
* I2C2 EEPROM
/*
* I2C
*/
-#define CONFIG_FSL_I2C /* Use FSL common I2C driver */
-#define CONFIG_HARD_I2C /* I2C with hardware support*/
-#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-#define CONFIG_SYS_I2C_NOPROBES {0x69} /* Don't probe these addrs */
-#define CONFIG_SYS_I2C_OFFSET 0x3000
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_FSL
+#define CONFIG_SYS_FSL_I2C_SPEED 400000
+#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
+#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} }
/* RapidIO MMU */
#define CONFIG_SYS_RIO_MEM_VIRT 0xc0000000 /* base address */
/*
* I2C
*/
-#define CONFIG_FSL_I2C /* Use FSL common I2C driver */
-#define CONFIG_HARD_I2C /* I2C with hardware support*/
-#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-#define CONFIG_SYS_I2C_NOPROBES {0x69} /* Don't probe these addrs */
-#define CONFIG_SYS_I2C_OFFSET 0x3000
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_FSL
+#define CONFIG_SYS_FSL_I2C_SPEED 400000
+#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
+#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} }
/* EEPROM */
#define CONFIG_ID_EEPROM
#define CONFIG_OF_STDOUT_VIA_ALIAS 1
/* I2C */
-#define CONFIG_FSL_I2C /* Use FSL common I2C driver */
-#define CONFIG_HARD_I2C /* I2C with hardware support */
-#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_FSL
+#define CONFIG_SYS_FSL_I2C_SPEED 400000
+#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
+#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} }
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-#define CONFIG_SYS_I2C_NOPROBES {0x69} /* Don't probe these addrs */
-#define CONFIG_SYS_I2C_OFFSET 0x3100
/*
* General PCI
/*
* I2C
*/
-#define CONFIG_FSL_I2C /* Use FSL common I2C driver */
-#define CONFIG_HARD_I2C /* I2C with hardware support*/
-#define CONFIG_SYS_I2C_SPEED 400000
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-#define CONFIG_SYS_I2C_NOPROBES {0x69} /* Don't probe these addrs */
-#define CONFIG_SYS_I2C_OFFSET 0x3000
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_FSL
+#define CONFIG_SYS_FSL_I2C_SPEED 400000
+#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
+#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} }
/* EEPROM */
#define CONFIG_ID_EEPROM
/*
* I2C
*/
-#define CONFIG_FSL_I2C /* Use FSL common I2C driver */
-#define CONFIG_HARD_I2C /* I2C with hardware support*/
-#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-#define CONFIG_SYS_I2C_NOPROBES {0x69} /* Don't probe these addrs */
-#define CONFIG_SYS_I2C_OFFSET 0x3000
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_FSL
+#define CONFIG_SYS_FSL_I2C_SPEED 400000
+#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
+#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} }
/* EEPROM */
#define CONFIG_ID_EEPROM
/*
* I2C
*/
-#define CONFIG_FSL_I2C /* Use FSL common I2C driver */
-#define CONFIG_HARD_I2C /* I2C with hardware support*/
-#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-#define CONFIG_SYS_I2C_NOPROBES {0x69} /* Don't probe these addrs */
-#define CONFIG_SYS_I2C_OFFSET 0x3000
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_FSL
+#define CONFIG_SYS_FSL_I2C_SPEED 400000
+#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
+#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} }
/* RapidIO MMU */
#define CONFIG_SYS_RIO_MEM_VIRT 0xc0000000 /* base address */
/*
* I2C
*/
-#define CONFIG_FSL_I2C /* Use FSL common I2C driver */
-#define CONFIG_HARD_I2C /* I2C with hardware support*/
-#define CONFIG_I2C_MULTI_BUS
-#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_FSL
+#define CONFIG_SYS_FSL_I2C_SPEED 400000
+#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
+#define CONFIG_SYS_FSL_I2C2_SPEED 400000
+#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
+#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} }
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x52
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-#define CONFIG_SYS_I2C_NOPROBES {{0,0x69}} /* Don't probe these addrs */
-#define CONFIG_SYS_I2C_OFFSET 0x3000
-#define CONFIG_SYS_I2C2_OFFSET 0x3100
/*
* General PCI
/*
* I2C
*/
-#define CONFIG_FSL_I2C /* Use FSL common I2C driver */
-#define CONFIG_HARD_I2C /* I2C with hardware support*/
-#define CONFIG_I2C_MULTI_BUS
-#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-#define CONFIG_SYS_I2C_NOPROBES {{0,0x69}} /* Don't probe these addrs */
-#define CONFIG_SYS_I2C_OFFSET 0x3000
-#define CONFIG_SYS_I2C2_OFFSET 0x3100
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_FSL
+#define CONFIG_SYS_FSL_I2C_SPEED 400000
+#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C2_SPEED 400000
+#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
+#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
+#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} }
/*
* I2C2 EEPROM
#define CONFIG_FIT_VERBOSE 1 /* enable fit_format_{error,warning}() */
/* I2C */
-#define CONFIG_FSL_I2C /* Use FSL common I2C driver */
-#define CONFIG_HARD_I2C /* I2C with hardware support */
-#define CONFIG_I2C_MULTI_BUS
-#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_FSL
+#define CONFIG_SYS_FSL_I2C_SPEED 400000
+#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
+#define CONFIG_SYS_FSL_I2C2_SPEED 400000
+#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
+#define CONFIG_SYS_I2C_NOPROBES { {0, 0x29} }
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-#define CONFIG_SYS_I2C_NOPROBES {{0,0x29}}/* Don't probe these addrs */
-#define CONFIG_SYS_I2C_OFFSET 0x3000
-#define CONFIG_SYS_I2C2_OFFSET 0x3100
/*
* I2C2 EEPROM
/*
* I2C
*/
-#define CONFIG_FSL_I2C /* Use FSL common I2C driver */
-#define CONFIG_HARD_I2C /* I2C with hardware support*/
-#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-#define CONFIG_SYS_I2C_NOPROBES {0x69} /* Don't probe these addrs */
-#define CONFIG_SYS_I2C_OFFSET 0x3000
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_FSL
+#define CONFIG_SYS_FSL_I2C_SPEED 400000
+#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
+#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} }
/*
* General PCI
/*
* I2C
*/
-#define CONFIG_FSL_I2C /* Use FSL common I2C driver */
-#define CONFIG_HARD_I2C /* I2C with hardware support*/
-#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-#define CONFIG_SYS_I2C_NOPROBES {0x69} /* Don't probe these addrs */
-#define CONFIG_SYS_I2C_OFFSET 0x3100
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_FSL
+#define CONFIG_SYS_FSL_I2C_SPEED 400000
+#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET 0x3100
+#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} }
/*
* RapidIO MMU
#define CONFIG_PCI
#define CONFIG_PCI_INDIRECT_BRIDGE
#define CONFIG_PCI_SKIP_HOST_BRIDGE
-#define CONFIG_HARD_I2C
#define CONFIG_TSEC_ENET
#define CONFIG_MPC8XXX_SPI
#define CONFIG_HARD_SPI
#define CONFIG_MISC_INIT_R
/* I2C */
-#define CONFIG_FSL_I2C
-#define CONFIG_I2C_MULTI_BUS
-#define CONFIG_SYS_I2C_OFFSET 0x3000
-#define CONFIG_SYS_I2C2_OFFSET 0x3100
-
-#define CONFIG_SYS_I2C_SPEED 100000
-#define CONFIG_SYS_I2C_SLAVE 0x7F
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_FSL
+#define CONFIG_SYS_FSL_I2C_SPEED 100000
+#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
+#define CONFIG_SYS_FSL_I2C2_SPEED 100000
+#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
/*
* DDR Setup
#define CONFIG_FIT
#define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */
-#define CONFIG_FSL_I2C /* Use FSL common I2C driver */
-#define CONFIG_HARD_I2C /* I2C with hardware support */
-#define CONFIG_I2C_MULTI_BUS
-#define CONFIG_I2C_CMD_TREE
-#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address*/
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-#define CONFIG_SYS_I2C_OFFSET 0x3000
-#define CONFIG_SYS_I2C2_OFFSET 0x3100
+/* I2C */
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_FSL
+#define CONFIG_SYS_FSL_I2C_SPEED 400000
+#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
+#define CONFIG_SYS_FSL_I2C2_SPEED 400000
+#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
/* I2C EEPROM */
#undef CONFIG_ID_EEPROM
#define CONFIG_FIT_VERBOSE
/* I2C */
-#define CONFIG_FSL_I2C
-#define CONFIG_HARD_I2C
-#define CONFIG_I2C_MULTI_BUS
-#define CONFIG_SYS_I2C_SPEED 400000
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57
-#define CONFIG_SYS_I2C_SLAVE 0x7F
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_FSL
+#define CONFIG_SYS_FSL_I2C_SPEED 400000
+#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
+#define CONFIG_SYS_FSL_I2C2_SPEED 400000
+#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
#define CONFIG_SYS_I2C_NOPROBES {{0, 0x29}}
-#define CONFIG_SYS_I2C_OFFSET 0x3000
-#define CONFIG_SYS_I2C2_OFFSET 0x3100
/*
* I2C2 EEPROM
#define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */
/* I2C */
-#define CONFIG_FSL_I2C /* Use FSL common I2C driver */
-#define CONFIG_HARD_I2C /* I2C with hardware support */
-#define CONFIG_I2C_MULTI_BUS
-#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-#define CONFIG_SYS_I2C_OFFSET 0x3000
-#define CONFIG_SYS_I2C2_OFFSET 0x3100
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_FSL
+#define CONFIG_SYS_FSL_I2C_SPEED 400000
+#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
+#define CONFIG_SYS_FSL_I2C2_SPEED 400000
+#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
/*
* I2C2 EEPROM
#define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */
/* I2C */
-#define CONFIG_FSL_I2C /* Use FSL common I2C driver */
-#define CONFIG_HARD_I2C /* I2C with hardware support */
-#define CONFIG_I2C_MULTI_BUS
-#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_FSL
+#define CONFIG_SYS_FSL_I2C_SPEED 400000
+#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
+#define CONFIG_SYS_FSL_I2C2_SPEED 400000
+#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x51
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-#define CONFIG_SYS_I2C_OFFSET 0x3000
-#define CONFIG_SYS_I2C2_OFFSET 0x3100
/*
* I2C2 EEPROM
#define CONFIG_FIT_VERBOSE 1 /* enable fit_format_{error,warning}() */
/* I2C */
-#define CONFIG_FSL_I2C /* Use FSL common I2C driver */
-#define CONFIG_HARD_I2C /* I2C with hardware support */
-#define CONFIG_I2C_MULTI_BUS
-#define CONFIG_I2C_CMD_TREE
-#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address*/
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-#define CONFIG_SYS_I2C_NOPROBES {{0,0x29}} /* Don't probe these addrs */
-#define CONFIG_SYS_I2C_OFFSET 0x3000
-#define CONFIG_SYS_I2C2_OFFSET 0x3100
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_FSL
+#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
+#define CONFIG_SYS_FSL_I2C_SPEED 400000
+#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
+#define CONFIG_SYS_FSL_I2C2_SPEED 400000
+#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
+#define CONFIG_SYS_I2C_NOPROBES { {0, 0x29} }
/*
* I2C2 EEPROM
#define CONFIG_FIT_VERBOSE 1
/* I2C */
-#define CONFIG_FSL_I2C /* Use FSL common I2C driver */
-#define CONFIG_HARD_I2C /* I2C with hardware support */
-#define CONFIG_I2C_MULTI_BUS
-#define CONFIG_I2C_CMD_TREE
-#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address*/
-#define CONFIG_SYS_I2C_SLAVE 0x7F
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_FSL
+#define CONFIG_SYS_FSL_I2C_SPEED 400000
+#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
+#define CONFIG_SYS_FSL_I2C2_SPEED 400000
+#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
#define CONFIG_SYS_I2C_NOPROBES { {0, 0x29} }
-#define CONFIG_SYS_I2C_OFFSET 0x3000
-#define CONFIG_SYS_I2C2_OFFSET 0x3100
/*
* I2C2 EEPROM
#define CONFIG_OF_STDOUT_VIA_ALIAS 1
/* I2C */
-#define CONFIG_FSL_I2C /* Use FSL common I2C driver */
-#define CONFIG_HARD_I2C /* I2C with hardware support */
-#define CONFIG_I2C_MULTI_BUS
-#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_FSL
+#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
+#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
+#define CONFIG_SYS_FSL_I2C_SPEED 400000
+#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C2_SPEED 400000
+#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-#define CONFIG_SYS_I2C_NOPROBES {{0,0x29}}/* Don't probe these addrs */
-#define CONFIG_SYS_I2C_OFFSET 0x3000
-#define CONFIG_SYS_I2C2_OFFSET 0x3100
+#define CONFIG_SYS_I2C_NOPROBES { {0, 0x29} }
/*
* I2C2 EEPROM
#define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */
/* I2C */
-#define CONFIG_FSL_I2C /* Use FSL common I2C driver */
-#define CONFIG_HARD_I2C /* I2C with hardware support */
-#define CONFIG_I2C_MULTI_BUS
-#define CONFIG_I2C_CMD_TREE
-#define CONFIG_SYS_I2C_SPEED 400000
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-#define CONFIG_SYS_I2C_OFFSET 0x118000
-#define CONFIG_SYS_I2C2_OFFSET 0x118100
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_FSL
+#define CONFIG_SYS_FSL_I2C_SPEED 400000
+#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
+#define CONFIG_SYS_FSL_I2C2_SPEED 400000
+#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
/*
* RapidIO
#define CONFIG_SYS_HUSH_PARSER
/* I2C */
-#define CONFIG_HARD_I2C /* I2C with hardware support*/
-#define CONFIG_FSL_I2C
-#define CONFIG_I2C_MULTI_BUS
-#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} } /* Don't probe these addrs */
-#define CONFIG_SYS_I2C_OFFSET 0x3000
-#define CONFIG_SYS_I2C2_OFFSET 0x3100
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_FSL
+#define CONFIG_SYS_FSL_I2C_SPEED 400000
+#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
+#define CONFIG_SYS_FSL_I2C2_SPEED 400000
+#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
+#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} }
/*
* General PCI
/*
* I2C
*/
-#define CONFIG_HARD_I2C /* I2C with hardware support */
-#define CONFIG_FSL_I2C
-#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed: 400KHz */
-#define CONFIG_SYS_I2C_SLAVE 0x7F /* slave address */
-#define CONFIG_SYS_I2C_OFFSET 0x3000
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_FSL
+#define CONFIG_SYS_FSL_I2C_SPEED 400000
+#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
/* I2C EEPROM, configuration for onboard EEPROMs 24C256 and 24C32 */
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* 1010000x */
#undef CONFIG_MCFPIT
/* I2C */
-#define CONFIG_FSL_I2C
-#define CONFIG_HARD_I2C /* I2C with hw support */
-#define CONFIG_SYS_I2C_SPEED 80000
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-#define CONFIG_SYS_I2C_OFFSET 0x58000
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_FSL
+#define CONFIG_SYS_FSL_I2C_SPEED 80000
+#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET 0x58000
#define CONFIG_SYS_IMMR CONFIG_SYS_MBAR
/*
/*
* I2C
*/
-#define CONFIG_HARD_I2C
-#define CONFIG_I2C_MULTI_BUS
-#define CONFIG_CMD_I2C
-
-#define CONFIG_FSL_I2C
-#define CONFIG_SYS_I2C_OFFSET 0x3000
-#define CONFIG_SYS_I2C2_OFFSET 0x3100
-#define CONFIG_SYS_I2C_SPEED 400000
-#define CONFIG_SYS_I2C_SLAVE 0x7F
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_FSL
+#define CONFIG_SYS_FSL_I2C_SPEED 400000
+#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
+#define CONFIG_SYS_FSL_I2C2_SPEED 400000
+#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
/* Probing DP501 I2C-Bridge will hang */
#define CONFIG_SYS_I2C_NOPROBES { {0, 0x30}, {0, 0x37}, {0, 0x3a}, \
{0, 0x3b}, {0, 0x50} }
#define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */
/* I2C */
-#define CONFIG_FSL_I2C /* Use FSL common I2C driver */
-#define CONFIG_HARD_I2C /* I2C with hardware support */
-#define CONFIG_I2C_MULTI_BUS
-#define CONFIG_I2C_CMD_TREE
-#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-#define CONFIG_SYS_I2C_OFFSET 0x118000
-#define CONFIG_SYS_I2C2_OFFSET 0x118100
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_FSL
+#define CONFIG_SYS_FSL_I2C_SPEED 400000
+#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET 0x118000
+#define CONFIG_SYS_FSL_I2C2_SPEED 400000
+#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C2_OFFSET 0x118100
/*
* RapidIO
* I2C
*/
-#define CONFIG_HARD_I2C
-#define CONFIG_FSL_I2C
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_FSL
-#define CONFIG_SYS_I2C_OFFSET 0x00000300
+#define CONFIG_SYS_FSL_I2C_OFFSET 0x00000300
#define CONFIG_SYS_IMMR CONFIG_SYS_MBAR
-#define CONFIG_SYS_I2C_SPEED 100000
-#define CONFIG_SYS_I2C_SLAVE 0
+#define CONFIG_SYS_FSL_I2C_SPEED 100000
+#define CONFIG_SYS_FSL_I2C_SLAVE 0
#ifdef CONFIG_CMD_DATE
#define CONFIG_RTC_DS1338
#endif /* CFG_SYS_RAMBOOT */
/* I2C */
-#define CONFIG_HARD_I2C /* I2C with hardware support */
-#define CONFIG_FSL_I2C
-#define CONFIG_SYS_I2C_SPEED 200000 /* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-#define CONFIG_SYS_I2C_OFFSET 0x3000
-#define CONFIG_I2C_MULTI_BUS
-#define CONFIG_SYS_MAX_I2C_BUS 1
-#define CONFIG_I2C_MUX
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_NUM_I2C_BUSES 4
+#define CONFIG_SYS_I2C_MAX_HOPS 1
+#define CONFIG_SYS_I2C_FSL
+#define CONFIG_SYS_FSL_I2C_SPEED 200000
+#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
+#define CONFIG_SYS_I2C_OFFSET 0x3000
+#define CONFIG_SYS_FSL_I2C2_SPEED 200000
+#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
+#define CONFIG_SYS_I2C_BUSES {{0, {I2C_NULL_HOP} }, \
+ {0, {{I2C_MUX_PCA9547, 0x70, 2} } }, \
+ {0, {{I2C_MUX_PCA9547, 0x70, 1} } }, \
+ {1, {I2C_NULL_HOP} } }
/* I2C SYSMON (LM75, AD7414 is almost compatible) */
#define CONFIG_DTT_LM75 /* ON Semi's LM75 */
#define CONFIG_SYS_DTT_MAX_TEMP 70
#define CONFIG_SYS_DTT_LOW_TEMP -30
#define CONFIG_SYS_DTT_HYSTERESIS 3
-#define CONFIG_SYS_DTT_BUS_NUM (CONFIG_SYS_MAX_I2C_BUS)
+#define CONFIG_SYS_DTT_BUS_NUM 1
#if defined(CONFIG_CMD_NAND)
#define CONFIG_NAND_KMETER1
#define CONFIG_EXTRA_ENV_SETTINGS \
CONFIG_KM_DEF_ENV \
CONFIG_KM_DEF_ARCH \
- "EEprom_ivm=pca9547:70:9\0" \
+ "EEprom_ivm=2\0" \
"newenv=" \
"prot off 0xF00C0000 +0x40000 && " \
"era 0xF00C0000 +0x40000\0" \
#define CONFIG_OF_STDOUT_VIA_ALIAS 1
/* I2C */
-#define CONFIG_HARD_I2C /* I2C with hardware support */
-#define CONFIG_FSL_I2C
-#define CONFIG_I2C_MULTI_BUS
-#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-#define CONFIG_SYS_I2C_OFFSET 0x3000
-#define CONFIG_SYS_I2C2_OFFSET 0x3100
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_FSL
+#define CONFIG_SYS_FSL_I2C_SPEED 400000
+#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C2_SPEED 400000
+#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
+#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
/*
* General PCI
/*
* I2C buses and peripherals
*/
-#define CONFIG_FSL_I2C /* Use FSL common I2C driver */
-#define CONFIG_HARD_I2C /* I2C with hardware support*/
-#define CONFIG_I2C_MULTI_BUS
-#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SLAVE 0x7f
-#define CONFIG_SYS_I2C_OFFSET 0x3000
-#define CONFIG_SYS_I2C2_OFFSET 0x3100
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_FSL
+#define CONFIG_SYS_FSL_I2C_SPEED 400000
+#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
+#define CONFIG_SYS_FSL_I2C2_SPEED 400000
+#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
+#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} }
/* I2C RTC - M41T81 */
#define CONFIG_RTC_M41T62
#define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */
/* I2C */
-#define CONFIG_FSL_I2C /* Use FSL common I2C driver */
-#define CONFIG_HARD_I2C /* I2C with hardware support */
-#define CONFIG_I2C_MULTI_BUS
-#define CONFIG_I2C_CMD_TREE
-#define CONFIG_SYS_I2C_SPEED 400000 /* I2C spd and slave address */
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_FSL
+#define CONFIG_SYS_FSL_I2C_SPEED 400000
+#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
+#define CONFIG_SYS_FSL_I2C2_SPEED 400000
+#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
+#define CONFIG_SYS_I2C_NOPROBES { {0, 0x29} }
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x52
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-#define CONFIG_SYS_I2C_NOPROBES {{0, 0x29}} /* Don't probe this addr */
-#define CONFIG_SYS_I2C_OFFSET 0x3000
-#define CONFIG_SYS_I2C2_OFFSET 0x3100
#define CONFIG_SYS_SPD_BUS_NUM 1 /* For rom_loc and flash bank */
/*
#define CONFIG_OF_STDOUT_VIA_ALIAS 1
/* I2C */
-#define CONFIG_HARD_I2C /* I2C with hardware support*/
-#define CONFIG_FSL_I2C
-#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-#define CONFIG_SYS_I2C_NOPROBES {0x69} /* Don't probe these addrs */
-#define CONFIG_SYS_I2C1_OFFSET 0x3000
-#define CONFIG_SYS_I2C2_OFFSET 0x3100
-#define CONFIG_SYS_I2C_OFFSET CONFIG_SYS_I2C2_OFFSET
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_FSL
+#define CONFIG_SYS_FSL_I2C_SPEED 400000
+#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
+#define CONFIG_SYS_FSL_I2C2_SPEED 400000
+#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
+#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69}, {1, 0x69} }
/* could also use CONFIG_I2C_MULTI_BUS and CONFIG_SYS_SPD_BUS_NUM... */
/* TSEC */
/*
* I2C
*/
-#define CONFIG_FSL_I2C /* Use FSL common I2C driver */
-#define CONFIG_HARD_I2C /* I2C with hardware support*/
-#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_FSL
+#define CONFIG_SYS_FSL_I2C_SPEED 400000
+#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-#define CONFIG_SYS_I2C_OFFSET 0x3000
/*
* General PCI
/*
* I2C
*/
-#define CONFIG_FSL_I2C /* Use FSL common I2C driver */
-#define CONFIG_HARD_I2C /* I2C with hardware support*/
-#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-#define CONFIG_SYS_I2C_NOPROBES {0x69} /* Don't probe these addrs */
-#define CONFIG_SYS_I2C_OFFSET 0x3100
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_FSL
+#define CONFIG_SYS_FSL_I2C_SPEED 400000
+#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET 0x3100
+#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} }
/*
* RapidIO MMU
/*
* I2C
*/
-#define CONFIG_FSL_I2C /* Use FSL common I2C driver */
-#define CONFIG_HARD_I2C /* I2C with hardware support */
-#define CONFIG_SYS_I2C_SPEED 102124 /* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-#define CONFIG_SYS_I2C_OFFSET 0x3000
-
-#define CONFIG_I2C_MULTI_BUS
-#define CONFIG_SYS_I2C2_OFFSET 0x3100
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_FSL
+#define CONFIG_SYS_FSL_I2C_SPEED 102124
+#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
+#define CONFIG_SYS_FSL_I2C2_SPEED 102124
+#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
/* I2C RTC */
#define CONFIG_RTC_RX8025 /* Use Epson rx8025 rtc via i2c */
/*
* I2C
*/
-#define CONFIG_FSL_I2C /* Use FSL common I2C driver */
-#define CONFIG_HARD_I2C /* I2C with hardware support*/
-#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SLAVE 0x7F
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_FSL
+#define CONFIG_SYS_FSL_I2C_SPEED 400000
+#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
+
#if 0
#define CONFIG_SYS_I2C_NOPROBES {0x00} /* Don't probe these addrs */
#else
/* I did the 'if 0' so we could keep the syntax above if ever needed. */
#undef CONFIG_SYS_I2C_NOPROBES
#endif
-#define CONFIG_SYS_I2C_OFFSET 0x3000
/* RapdIO Map configuration, mapped 1:1.
*/
/*
* I2C
*/
-#define CONFIG_FSL_I2C /* Use FSL common I2C driver */
-#define CONFIG_HARD_I2C /* I2C with hardware support*/
-#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SLAVE 0x7F
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_FSL
+#define CONFIG_SYS_FSL_I2C_SPEED 400000
+#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
#undef CONFIG_SYS_I2C_NOPROBES
-#define CONFIG_SYS_I2C_OFFSET 0x3000
/* I2C RTC */
#define CONFIG_RTC_DS1337 /* This is really a DS1339 RTC */
#define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */
/* I2C */
-#define CONFIG_FSL_I2C /* Use FSL common I2C driver */
-#define CONFIG_HARD_I2C /* I2C with hardware support */
-#define CONFIG_I2C_MULTI_BUS
-#define CONFIG_I2C_CMD_TREE
-#define CONFIG_SYS_I2C_SPEED 100000 /* I2C speed */
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-#define CONFIG_SYS_I2C_OFFSET 0x118000
-#define CONFIG_SYS_I2C2_OFFSET 0x118100
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_FSL
+#define CONFIG_SYS_FSL_I2C_SPEED 100000
+#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET 0x118000
+#define CONFIG_SYS_FSL_I2C2_SPEED 100000
+#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C2_OFFSET 0x118100
+
#define I2C_MUX_PCA_ADDR_PRI 0x77 /* I2C bus multiplexer,primary */
#define I2C_MUX_PCA_ADDR_SEC 0x76 /* I2C bus multiplexer,secondary */
#define CONFIG_OF_STDOUT_VIA_ALIAS
/* I2C */
-#define CONFIG_I2C_MULTI_BUS
-#define CONFIG_HARD_I2C /* I2C with hardware support*/
-#define CONFIG_FSL_I2C
-#define CONFIG_I2C_CMD_TREE
-#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} } /* Don't probe these addrs */
-#define CONFIG_SYS_I2C1_OFFSET 0x3000
-#define CONFIG_SYS_I2C2_OFFSET 0x3100
-#define CONFIG_SYS_I2C_OFFSET CONFIG_SYS_I2C1_OFFSET
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_FSL
+#define CONFIG_SYS_FSL_I2C_SPEED 400000
+#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
+#define CONFIG_SYS_FSL_I2C2_SPEED 400000
+#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
+#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} }
/* could also use CONFIG_I2C_MULTI_BUS and CONFIG_SYS_SPD_BUS_NUM... */
#define CONFIG_SYS_I2C_8574_ADDR2 0x20 /* I2C1, PCF8574 */
/*
* I2C
*/
-#define CONFIG_FSL_I2C /* Use FSL common I2C driver */
-#define CONFIG_HARD_I2C /* I2C with hardware support */
-#define CONFIG_SYS_I2C_SPEED 100000 /* M41T00 only supports 100 KHz */
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-#define CONFIG_SYS_I2C_OFFSET 0x3000
-#define CONFIG_SYS_I2C2_OFFSET 0x3100
-#define CONFIG_I2C_MULTI_BUS
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_FSL
+#define CONFIG_SYS_FSL_I2C_SPEED 100000
+#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
+#define CONFIG_SYS_FSL_I2C2_SPEED 100000
+#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
/* PEX8518 slave I2C interface */
#define CONFIG_SYS_I2C_PEX8518_ADDR 0x70
/*
* I2C
*/
-#define CONFIG_FSL_I2C /* Use FSL common I2C driver */
-#define CONFIG_HARD_I2C /* I2C with hardware support */
-#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-#define CONFIG_SYS_I2C_OFFSET 0x3000
-#define CONFIG_SYS_I2C2_OFFSET 0x3100
-#define CONFIG_I2C_MULTI_BUS
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_FSL
+#define CONFIG_SYS_FSL_I2C_SPEED 400000
+#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
+#define CONFIG_SYS_FSL_I2C2_SPEED 400000
+#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
/* I2C EEPROM */
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
/*
* I2C
*/
-#define CONFIG_FSL_I2C /* Use FSL common I2C driver */
-#define CONFIG_HARD_I2C /* I2C with hardware support */
-#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-#define CONFIG_SYS_I2C_OFFSET 0x3000
-#define CONFIG_SYS_I2C2_OFFSET 0x3100
-#define CONFIG_I2C_MULTI_BUS
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_FSL
+#define CONFIG_SYS_FSL_I2C_SPEED 400000
+#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
+#define CONFIG_SYS_FSL_I2C2_SPEED 400000
+#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
+#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} }
/* PEX8518 slave I2C interface */
#define CONFIG_SYS_I2C_PEX8518_ADDR 0x70
/*
* I2C
*/
-#define CONFIG_FSL_I2C /* Use FSL common I2C driver */
-#define CONFIG_HARD_I2C /* I2C with hardware support */
-#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-#define CONFIG_SYS_I2C_OFFSET 0x3000
-#define CONFIG_SYS_I2C2_OFFSET 0x3100
-#define CONFIG_I2C_MULTI_BUS
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_FSL
+#define CONFIG_SYS_FSL_I2C_SPEED 400000
+#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
+#define CONFIG_SYS_FSL_I2C2_SPEED 400000
+#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
/* I2C DS7505 temperature sensor */
#define CONFIG_DTT_LM75
projects / platform / kernel / u-boot.git / commitdiff