omap2/3/4: serial: errata i202: fix for MDR1 access

Errata i202 (OMAP3430 - 1.12, OMAP3630 - 1.6):
UART module MDR1 register access can cause a dummy underrun
condition which could result in a freeze in the case of IrDA
communication or if used as UART, corrupted data.

Workaround is as follows for everytime MDR1 register is changed:
* setup all required UART registers
* setup MDR1.MODE_SELECT bit field
* Wait 5 L4 clk cycles + 5 UART functional clock cycles
* Clear the Tx and RX fifo using FCR register

Note: The following step is not done as I am assuming it is not
needed due to reconfiguration being done and there is no halted
operation perse.
* Read if required, the RESUME register to resume halted operation

Based on an earlier patch at:
http://git.omapzoom.org/?p=kernel/omap.git;a=commitdiff;h=42d4a342c009bd9727c100abc8a4bc3063c22f0c

Signed-off-by: Deepak K <deepak.k@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

diff --git a/arch/arm/mach-omap2/serial.c b/arch/arm/mach-omap2/serial.c
index 009b63f..566e991 100644 (file)
--- a/arch/arm/mach-omap2/serial.c
+++ b/arch/arm/mach-omap2/serial.c
@@ -38,6 +38,7 @@
 #define UART_OMAP_WER          0x17    /* Wake-up enable register */
 
 #define UART_ERRATA_FIFO_FULL_ABORT    (0x1 << 0)
+#define UART_ERRATA_i202_MDR1_ACCESS   (0x1 << 1)
 
 /*
  * NOTE: By default the serial timeout is disabled as it causes lost characters
@@ -184,6 +185,42 @@ static inline void __init omap_uart_reset(struct omap_uart_state *uart)
 
 #if defined(CONFIG_PM) && defined(CONFIG_ARCH_OMAP3)
 
+/*
+ * Work Around for Errata i202 (3430 - 1.12, 3630 - 1.6)
+ * The access to uart register after MDR1 Access
+ * causes UART to corrupt data.
+ *
+ * Need a delay =
+ * 5 L4 clock cycles + 5 UART functional clock cycle (@48MHz = ~0.2uS)
+ * give 10 times as much
+ */
+static void omap_uart_mdr1_errataset(struct omap_uart_state *uart, u8 mdr1_val,
+               u8 fcr_val)
+{
+       struct plat_serial8250_port *p = uart->p;
+       u8 timeout = 255;
+
+       serial_write_reg(p, UART_OMAP_MDR1, mdr1_val);
+       udelay(2);
+       serial_write_reg(p, UART_FCR, fcr_val | UART_FCR_CLEAR_XMIT |
+                       UART_FCR_CLEAR_RCVR);
+       /*
+        * Wait for FIFO to empty: when empty, RX_FIFO_E bit is 0 and
+        * TX_FIFO_E bit is 1.
+        */
+       while (UART_LSR_THRE != (serial_read_reg(p, UART_LSR) &
+                               (UART_LSR_THRE | UART_LSR_DR))) {
+               timeout--;
+               if (!timeout) {
+                       /* Should *never* happen. we warn and carry on */
+                       dev_crit(&uart->pdev.dev, "Errata i202: timedout %x\n",
+                               serial_read_reg(p, UART_LSR));
+                       break;
+               }
+               udelay(1);
+       }
+}
+
 static void omap_uart_save_context(struct omap_uart_state *uart)
 {
        u16 lcr = 0;
@@ -221,7 +258,10 @@ static void omap_uart_restore_context(struct omap_uart_state *uart)
 
        uart->context_valid = 0;
 
-       serial_write_reg(p, UART_OMAP_MDR1, 0x7);
+       if (uart->errata & UART_ERRATA_i202_MDR1_ACCESS)
+               omap_uart_mdr1_errataset(uart, 0x07, 0xA0);
+       else
+               serial_write_reg(p, UART_OMAP_MDR1, 0x7);
        serial_write_reg(p, UART_LCR, 0xBF); /* Config B mode */
        efr = serial_read_reg(p, UART_EFR);
        serial_write_reg(p, UART_EFR, UART_EFR_ECB);
@@ -234,14 +274,16 @@ static void omap_uart_restore_context(struct omap_uart_state *uart)
        serial_write_reg(p, UART_IER, uart->ier);
        serial_write_reg(p, UART_LCR, 0x80);
        serial_write_reg(p, UART_MCR, uart->mcr);
-       serial_write_reg(p, UART_FCR, 0xA1);
        serial_write_reg(p, UART_LCR, 0xBF); /* Config B mode */
        serial_write_reg(p, UART_EFR, efr);
        serial_write_reg(p, UART_LCR, UART_LCR_WLEN8);
        serial_write_reg(p, UART_OMAP_SCR, uart->scr);
        serial_write_reg(p, UART_OMAP_WER, uart->wer);
        serial_write_reg(p, UART_OMAP_SYSC, uart->sysc);
-       serial_write_reg(p, UART_OMAP_MDR1, 0x00); /* UART 16x mode */
+       if (uart->errata & UART_ERRATA_i202_MDR1_ACCESS)
+               omap_uart_mdr1_errataset(uart, 0x00, 0xA1);
+       else
+               serial_write_reg(p, UART_OMAP_MDR1, 0x00); /* UART 16x mode */
 }
 #else
 static inline void omap_uart_save_context(struct omap_uart_state *uart) {}
@@ -769,6 +811,10 @@ void __init omap_serial_init_port(int port)
                uart->p->serial_in = serial_in_override;
                uart->p->serial_out = serial_out_override;
        }
+
+       /* Enable the MDR1 errata for OMAP3 */
+       if (cpu_is_omap34xx())
+               uart->errata |= UART_ERRATA_i202_MDR1_ACCESS;
 }
 
 /**