summary |
shortlog |
log |
commit | commitdiff |
tree
raw |
patch |
inline | side by side (from parent 1:
9c4d678)
Use usbhs_init_phys() to register the PHY's RESET regulator
and the NOP PHY device. VAUX2 supplies the PHY's VCC.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
static struct regulator_consumer_supply omap3evm_vaux2_supplies[] = {
REGULATOR_SUPPLY("VDD_CSIPHY1", "omap3isp"), /* OMAP ISP */
REGULATOR_SUPPLY("VDD_CSIPHY2", "omap3isp"), /* OMAP ISP */
static struct regulator_consumer_supply omap3evm_vaux2_supplies[] = {
REGULATOR_SUPPLY("VDD_CSIPHY1", "omap3isp"), /* OMAP ISP */
REGULATOR_SUPPLY("VDD_CSIPHY2", "omap3isp"), /* OMAP ISP */
- REGULATOR_SUPPLY("hsusb1", "ehci-omap.0"),
+ REGULATOR_SUPPLY("vcc", "nop_usb_xceiv.2"), /* hsusb port 2 */
REGULATOR_SUPPLY("vaux2", NULL),
};
REGULATOR_SUPPLY("vaux2", NULL),
};
-static struct usbhs_omap_platform_data usbhs_bdata __initdata = {
+static struct usbhs_phy_data phy_data[] __initdata = {
+ {
+ .port = 2,
+ .reset_gpio = -1, /* set at runtime */
+ .vcc_gpio = -EINVAL,
+ },
+};
- .port_mode[0] = OMAP_USBHS_PORT_MODE_UNUSED,
+static struct usbhs_omap_platform_data usbhs_bdata __initdata = {
.port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
.port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
- .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED,
-
- .phy_reset = true,
- /* PHY reset GPIO will be runtime programmed based on EVM version */
- .reset_gpio_port[0] = -EINVAL,
- .reset_gpio_port[1] = -EINVAL,
- .reset_gpio_port[2] = -EINVAL
};
#ifdef CONFIG_OMAP_MUX
};
#ifdef CONFIG_OMAP_MUX
/* setup EHCI phy reset config */
omap_mux_init_gpio(21, OMAP_PIN_INPUT_PULLUP);
/* setup EHCI phy reset config */
omap_mux_init_gpio(21, OMAP_PIN_INPUT_PULLUP);
- usbhs_bdata.reset_gpio_port[1] = 21;
+ phy_data[0].reset_gpio = 21;
/* EVM REV >= E can supply 500mA with EXTVBUS programming */
musb_board_data.power = 500;
/* EVM REV >= E can supply 500mA with EXTVBUS programming */
musb_board_data.power = 500;
} else {
/* setup EHCI phy reset on MDC */
omap_mux_init_gpio(135, OMAP_PIN_OUTPUT);
} else {
/* setup EHCI phy reset on MDC */
omap_mux_init_gpio(135, OMAP_PIN_OUTPUT);
- usbhs_bdata.reset_gpio_port[1] = 135;
+ phy_data[0].reset_gpio = 135;
}
usb_bind_phy("musb-hdrc.0.auto", 0, "twl4030_usb");
usb_musb_init(&musb_board_data);
}
usb_bind_phy("musb-hdrc.0.auto", 0, "twl4030_usb");
usb_musb_init(&musb_board_data);
+
+ usbhs_init_phys(phy_data, ARRAY_SIZE(phy_data));
usbhs_init(&usbhs_bdata);
board_nand_init(omap3evm_nand_partitions,
ARRAY_SIZE(omap3evm_nand_partitions), NAND_CS,
usbhs_init(&usbhs_bdata);
board_nand_init(omap3evm_nand_partitions,
ARRAY_SIZE(omap3evm_nand_partitions), NAND_CS,