This patch cleans up the Freescale MPC8308RDB Development board support.
Things fixed:
- Removed unused PCIE2 definitions from configuration
- SICR{L,H} defines used for System I/O Configuration Registers values
instead of hardcoding
- CONFIG_SYS_SCCR_PCIEXP1CM used to enable PCIE clock instead of
writing to SCCR from the board code
- sleep mode stuff removed as MPC8308 has no support for deep sleep and
PMCCR1 register. board_early_init_f() removed.
- MPC8308 has no ERRATA for DDR controller so workaround removed
- 'assignment in if statement' issues solved
- use LBLAWAR_* defines instead of hardcoding
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
-int board_early_init_f(void)
-{
- immap_t *im = (immap_t *)CONFIG_SYS_IMMR;
-
- if (in_be32(&im->pmc.pmccr1) & PMCCR1_POWER_OFF)
- gd->flags |= GD_FLG_SILENT;
-
- return 0;
-}
-
static u8 read_board_info(void)
{
u8 val8;
static u8 read_board_info(void)
{
u8 val8;
{
immap_t *immr = (immap_t *)CONFIG_SYS_IMMR;
sysconf83xx_t *sysconf = &immr->sysconf;
{
immap_t *immr = (immap_t *)CONFIG_SYS_IMMR;
sysconf83xx_t *sysconf = &immr->sysconf;
- clk83xx_t *clk = (clk83xx_t *)&immr->clk;
law83xx_t *pcie_law = sysconf->pcielaw;
struct pci_region *pcie_reg[] = { pcie_regions_0 };
fsl_setup_serdes(CONFIG_FSL_SERDES1, FSL_SERDES_PROTO_PEX,
FSL_SERDES_CLK_100, FSL_SERDES_VDD_1V);
law83xx_t *pcie_law = sysconf->pcielaw;
struct pci_region *pcie_reg[] = { pcie_regions_0 };
fsl_setup_serdes(CONFIG_FSL_SERDES1, FSL_SERDES_PROTO_PEX,
FSL_SERDES_CLK_100, FSL_SERDES_VDD_1V);
- clrsetbits_be32(&clk->sccr, SCCR_PCIEXP1CM ,
- SCCR_PCIEXP1CM_1);
-
/* Deassert the resets in the control register */
out_be32(&sysconf->pecr1, 0xE0008000);
udelay(2000);
/* Deassert the resets in the control register */
out_be32(&sysconf->pecr1, 0xE0008000);
udelay(2000);
int rv, num_if = 0;
/* Initialize TSECs first */
int rv, num_if = 0;
/* Initialize TSECs first */
- if ((rv = cpu_eth_init(bis)) >= 0)
+ rv = cpu_eth_init(bis);
+ if (rv >= 0)
num_if += rv;
else
printf("ERROR: failed to initialize TSECs.\n");
num_if += rv;
else
printf("ERROR: failed to initialize TSECs.\n");
- if ((rv = pci_eth_init(bis)) >= 0)
+ rv = pci_eth_init(bis);
+ if (rv >= 0)
num_if += rv;
else
printf("ERROR: failed to initialize PCI Ethernet.\n");
num_if += rv;
else
printf("ERROR: failed to initialize PCI Ethernet.\n");
-static void resume_from_sleep(void)
-{
- u32 magic = *(u32 *)0;
-
- typedef void (*func_t)(void);
- func_t resume = *(func_t *)4;
-
- if (magic == 0xf5153ae5)
- resume();
-
- gd->flags &= ~GD_FLG_SILENT;
- puts("\nResume from sleep failed: bad magic word\n");
-}
-
/* Fixed sdram init -- doesn't use serial presence detect.
*
* This is useful for faster booting in configs where the RAM is unlikely
/* Fixed sdram init -- doesn't use serial presence detect.
*
* This is useful for faster booting in configs where the RAM is unlikely
out_be32(&im->sysconf.ddrlaw[0].ar, LBLAWAR_EN | (msize_log2 - 1));
out_be32(&im->sysconf.ddrcdr, CONFIG_SYS_DDRCDR_VALUE);
out_be32(&im->sysconf.ddrlaw[0].ar, LBLAWAR_EN | (msize_log2 - 1));
out_be32(&im->sysconf.ddrcdr, CONFIG_SYS_DDRCDR_VALUE);
- /*
- * Erratum DDR3 requires a 50ms delay after clearing DDRCDR[DDR_cfg],
- * or the DDR2 controller may fail to initialize correctly.
- */
- udelay(50000);
-
out_be32(&im->ddr.csbnds[0].csbnds, (msize - 1) >> 24);
out_be32(&im->ddr.cs_config[0], CONFIG_SYS_DDR_CS0_CONFIG);
out_be32(&im->ddr.csbnds[0].csbnds, (msize - 1) >> 24);
out_be32(&im->ddr.cs_config[0], CONFIG_SYS_DDR_CS0_CONFIG);
out_be32(&im->ddr.timing_cfg_2, CONFIG_SYS_DDR_TIMING_2);
out_be32(&im->ddr.timing_cfg_0, CONFIG_SYS_DDR_TIMING_0);
out_be32(&im->ddr.timing_cfg_2, CONFIG_SYS_DDR_TIMING_2);
out_be32(&im->ddr.timing_cfg_0, CONFIG_SYS_DDR_TIMING_0);
- if (in_be32(&im->pmc.pmccr1) & PMCCR1_POWER_OFF) {
- out_be32(&im->ddr.sdram_cfg,
- CONFIG_SYS_DDR_SDRAM_CFG | SDRAM_CFG_BI);
- } else {
- out_be32(&im->ddr.sdram_cfg, CONFIG_SYS_DDR_SDRAM_CFG);
- }
-
+ out_be32(&im->ddr.sdram_cfg, CONFIG_SYS_DDR_SDRAM_CFG);
out_be32(&im->ddr.sdram_cfg2, CONFIG_SYS_DDR_SDRAM_CFG2);
out_be32(&im->ddr.sdram_mode, CONFIG_SYS_DDR_MODE);
out_be32(&im->ddr.sdram_mode2, CONFIG_SYS_DDR_MODE2);
out_be32(&im->ddr.sdram_cfg2, CONFIG_SYS_DDR_SDRAM_CFG2);
out_be32(&im->ddr.sdram_mode, CONFIG_SYS_DDR_MODE);
out_be32(&im->ddr.sdram_mode2, CONFIG_SYS_DDR_MODE2);
/* DDR SDRAM */
msize = fixed_sdram();
/* DDR SDRAM */
msize = fixed_sdram();
- if (in_be32(&im->pmc.pmccr1) & PMCCR1_POWER_OFF)
- resume_from_sleep();
-
/* return total bus SDRAM size(bytes) -- DDR */
return msize;
}
/* return total bus SDRAM size(bytes) -- DDR */
return msize;
}
-#define CONFIG_SYS_SICRH 0x01b7d103
-#define CONFIG_SYS_SICRL 0x00000040 /* 3.3V, no delay */
-
-#define CONFIG_BOARD_EARLY_INIT_F /* call board_pre_init */
+#define CONFIG_SYS_SICRH (\
+ SICRH_ESDHC_A_SD |\
+ SICRH_ESDHC_B_SD |\
+ SICRH_ESDHC_C_SD |\
+ SICRH_GPIO_A_TSEC2 |\
+ SICRH_GPIO_B_TSEC2_GTX_CLK125 |\
+ SICRH_IEEE1588_A_GPIO |\
+ SICRH_USB |\
+ SICRH_GTM_GPIO |\
+ SICRH_IEEE1588_B_GPIO |\
+ SICRH_ETSEC2_CRS |\
+ SICRH_GPIOSEL_1 |\
+ SICRH_TMROBI_V3P3 |\
+ SICRH_TSOBI1_V2P5 |\
+ SICRH_TSOBI2_V2P5) /* 0x01b7d103 */
+#define CONFIG_SYS_SICRL (\
+ SICRL_SPI_PF0 |\
+ SICRL_UART_PF0 |\
+ SICRL_IRQ_PF0 |\
+ SICRL_I2C2_PF0 |\
+ SICRL_ETSEC1_GTX_CLK125) /* 0x00000040 */
/* Window base at flash base */
#define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE
/* Window base at flash base */
#define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_LBLAWAR0_PRELIM 0x80000016 /* 8MB window size */
+#define CONFIG_SYS_LBLAWAR0_PRELIM (LBLAWAR_EN | LBLAWAR_8MB)
#define CONFIG_SYS_BR0_PRELIM (\
CONFIG_SYS_FLASH_BASE /* Flash Base address */ |\
#define CONFIG_SYS_BR0_PRELIM (\
CONFIG_SYS_FLASH_BASE /* Flash Base address */ |\
/* 0xFFFF8396 */
#define CONFIG_SYS_LBLAWBAR1_PRELIM CONFIG_SYS_NAND_BASE
/* 0xFFFF8396 */
#define CONFIG_SYS_LBLAWBAR1_PRELIM CONFIG_SYS_NAND_BASE
-#define CONFIG_SYS_LBLAWAR1_PRELIM 0x8000000E /* 32KB */
+#define CONFIG_SYS_LBLAWAR1_PRELIM (LBLAWAR_EN | LBLAWAR_32KB)
#ifdef CONFIG_VSC7385_ENET
#define CONFIG_TSEC2
#ifdef CONFIG_VSC7385_ENET
#define CONFIG_TSEC2
/* Access window base at VSC7385 base */
#define CONFIG_SYS_LBLAWBAR2_PRELIM CONFIG_SYS_VSC7385_BASE
/* Access window size 128K */
/* Access window base at VSC7385 base */
#define CONFIG_SYS_LBLAWBAR2_PRELIM CONFIG_SYS_VSC7385_BASE
/* Access window size 128K */
-#define CONFIG_SYS_LBLAWAR2_PRELIM 0x80000010
+#define CONFIG_SYS_LBLAWAR2_PRELIM (LBLAWAR_EN | LBLAWAR_128KB)
/* The flash address and size of the VSC7385 firmware image */
#define CONFIG_VSC7385_IMAGE 0xFE7FE000
#define CONFIG_VSC7385_IMAGE_SIZE 8192
/* The flash address and size of the VSC7385 firmware image */
#define CONFIG_VSC7385_IMAGE 0xFE7FE000
#define CONFIG_VSC7385_IMAGE_SIZE 8192
#define CONFIG_SYS_PCIE1_IO_PHYS 0xB1000000
#define CONFIG_SYS_PCIE1_IO_SIZE 0x00800000
#define CONFIG_SYS_PCIE1_IO_PHYS 0xB1000000
#define CONFIG_SYS_PCIE1_IO_SIZE 0x00800000
-/*
- * Fake PCIE2 definitions: there is no PCIE2 on this board but the code
- * in arch/powerpc/cpu/mpc83xx/pcie.c doesn't compile without this
- */
-#define CONFIG_SYS_PCIE2_BASE 0xC0000000
-#define CONFIG_SYS_PCIE2_MEM_BASE 0xC0000000
-#define CONFIG_SYS_PCIE2_MEM_PHYS 0xC0000000
-#define CONFIG_SYS_PCIE2_MEM_SIZE 0x10000000
-#define CONFIG_SYS_PCIE2_CFG_BASE 0xD0000000
-#define CONFIG_SYS_PCIE2_CFG_SIZE 0x01000000
-#define CONFIG_SYS_PCIE2_IO_BASE 0x00000000
-#define CONFIG_SYS_PCIE2_IO_PHYS 0xD1000000
-#define CONFIG_SYS_PCIE2_IO_SIZE 0x00800000
+/* enable PCIE clock */
+#define CONFIG_SYS_SCCR_PCIEXP1CM 1
#define CONFIG_PCI
#define CONFIG_PCIE
#define CONFIG_PCI
#define CONFIG_PCIE