Merge tag 'renesas-arm64-dt-for-v4.17' of ssh://gitolite.kernel.org/pub/scm/linux...

Merge tag 'renesas-arm64-dt-for-v4.17' of ssh://gitolite./linux/kernel/git/horms/renesas into next/dt

Pull "Renesas ARM64 Based SoC DT Updates for v4.17" from Simon Horman:

* R-Car Gen3 boards and SoCs
  - Make phy-mode of EtherAVB a board-specific property.

    The SoC DTs file now uses "rgmii" and boards override this with
    "rgmii-txid" as appropriate. Previously "rgmii-txid" was used
    in SoC DTs but this did not describe that more sophiticated
    functionality is a board rather than SoC property.

* Condor board with R-Car V3H (r8a77980) SoC
  - Initial upstream support

* Condor board with R-Car V3H (r8a77980) SoC
  - Initial upstream support

* R-Car D3 (r8a77995)
  - Add I2C nodes and then describing the PCA9654 I/O expander connected to
    the I2C0 bus.

* Eagle board with R-Car V3M (r8a77970) SoC
  - Enable PFC support for configuring SCIF0 pins
    This uses PFC support added to the V3M DT

  - Describe EtherAVB PHY IRQ
    This uses support for GPIO added to the V3M DT

  - Enable I2C0 support

    Sergei Shtylyov says "The I2C0 bus is populated by ON Semiconductor
    PCA9653 I/O expander and Analog Devices ADV7511W HDMI transmitter (but
    we're only describing the former chip now)."

* R-Car V3M (r8a77970) SoCs
  - Add PFC support
  - Describe GPIO devices
  - Describe I2C devices
  - Srt subnodes of root node alphabetically to eas future maintence overhead

* Draak board with R-Car D3 (r8a77995) SoC
  - Enable SDHI2

    Wolfram Sang says "The single SDHI controller is connected to eMMC."

  - Enable DU

    Kieran Bingham says "Enable the DU, providing only the VGA output for
    now."

* R-Car D3 (r8a77995) and V3M (r8a77970) SoCs
  - Move nodes which have no reg property out of bus
    By deffinition the bus only has hardware with an address on the bus

  - Remove non-existing STBE region from EtherAVB
    Stream Buffer for EtherAVB-IF (STBE) is not present on these SoCs

* R-Car D3 (r8a77995) SoC
  - Add FCPV, VSP and DU support

    Kieran Bingham says "The r8a77995-d3 platform supports 3 VSP instances.
    One VSPBS can be used as a dual-input image blender, while two VSPD
    instances can be utilised as part of a display (DU) pipeline.

    Add support for these, along with their required FCPV nodes."

* Salvator-X and Salvator-XS boards with R-Car Gen3 SoCs
  - Add GPIO extender
    This is a basis for follow-up work to configure the GPIOs of the extender

* Salvator-X and Salvator-XS board with R-Car M3-N (r8a77965) SoC
  - Initial upstream support

* R-Car H3 (r8a7795) and M3-W (r8a7796) SoCs
  - Add OPPs table for cpu devices
    This, along with recently upstreamed Z and Z2 clock support allows
    use of CPUFreq with both A57 and A53 CPUs.

  - Add thermal cooling management
    Allows the use of CPUFreq as a cooling device on A57 CPUs

  - Correct register size of thermal node

    Niklas Söderlund says "To be able to read fused calibration values from
    hardware the size of the register resource of TSC1 needs to be
    incremented to cover one more register which holds the information if
    the calibration values have been fused or not.

    Instead of increasing TSC1 size to the value from the datasheet update
    all TSC's size to the smallest granularity of the address decoder
    circuitry"

  - Fix register mappings on VSPs

    Kieran Bingham says "The VSPD includes a CLUT on RPF2. Ensure that the
    register space is mapped correctly to support this."

* R-Car H3 (r8a7795) SoC
  - Move SCIF node into alphabetical order to ease future maintenance overhead

  - Add IPMMU-PV1 device node

    This resolves an oversight when IPMMU nodes were added to the H3 DT.
    All IPMMU devices should now be described in DT.

  - Add missing SYS-DMAC2 dmas

    Geert Uytterhoeven says "On R-Car H3, on-chip peripheral modules that
    can make use of DMA are wired to either SYS-DMAC0 only, or to both
    SYS-DMAC1 and SYS-DMAC2.

    Add the missing DMA properties pointing to SYS-DMAC2 for HSCIF[0-2],
    SCIF[0125], and I2C[0-2].  These were initially left out because early
    firmware versions prohibited using SYS-DMAC2.  This restriction has
    been lifted in IPL and Secure Monitor Rev1.0.6 (released on Feb 25,
    2016)."

* tag 'renesas-arm64-dt-for-v4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (69 commits)
  arm64: dts: renesas: v3msk: add SCIF0 pins
  arm64: dts: renesas: r8a7795: Add missing SYS-DMAC2 dmas
  arm64: dts: renesas: r8a7795: Add IPMMU-PV1 device node
  arm64: dts: renesas: r8a77970: sort subnodes of root node alphabetically
  arm64: dts: renesas: eagle: add I2C0 support
  arm64: dts: renesas: r8a77970: add I2C support
  arm64: dts: renesas: r8a77965-salvator-xs: Add SoC name to file header
  arm64: dts: renesas: r8a77965: Add EtherAVB device node
  arm64: dts: renesas: r8a77970: Set EtherAVB phy mode to "rgmii"
  arm64: dts: renesas: r8a77995: Set EtherAVB phy mode to "rgmii"
  arm64: dts: renesas: r8a7795: Set EtherAVB phy mode to "rgmii"
  arm64: dts: renesas: r8a7796: Set EtherAVB phy mode to "rgmii"
  arm64: dts: renesas: v3msk: Override EtherAVB phy-mode
  arm64: dts: renesas: eagle: Override EtherAVB phy-mode
  arm64: dts: renesas: draak: Override EtherAVB phy-mode
  arm64: dts: renesas: ulcb: Override EtherAVB phy-mode
  arm64: dts: renesas: salvator-common: Override EtherAVB phy-mode
  arm64: dts: renesas: r8a77965: Add INTC-EX device node
  arm64: dts: renesas: r8a77965: Add IIC-DVFS device node
  arm64: dts: renesas: Add support for Salvator-XS with R-Car M3-N
  ...