ahci: don't ignore result code of ahci_reset_controller()
authorArd Biesheuvel <ard.biesheuvel@linaro.org>
Mon, 2 Oct 2017 18:31:24 +0000 (19:31 +0100)
committerTejun Heo <tj@kernel.org>
Mon, 2 Oct 2017 19:21:30 +0000 (12:21 -0700)
commitd312fefea8387503375f728855c9a62de20c9665
treef3158ccdcb6bd390bc6f4f51ae5b3f44e6da9561
parent80a921e207cea3dd18038501187078669a218dab
ahci: don't ignore result code of ahci_reset_controller()

ahci_pci_reset_controller() calls ahci_reset_controller(), which may
fail, but ignores the result code and always returns success. This
may result in failures like below

  ahci 0000:02:00.0: version 3.0
  ahci 0000:02:00.0: enabling device (0000 -> 0003)
  ahci 0000:02:00.0: SSS flag set, parallel bus scan disabled
  ahci 0000:02:00.0: controller reset failed (0xffffffff)
  ahci 0000:02:00.0: failed to stop engine (-5)
    ... repeated many times ...
  ahci 0000:02:00.0: failed to stop engine (-5)
  Unable to handle kernel paging request at virtual address ffff0000093f9018
    ...
  PC is at ahci_stop_engine+0x5c/0xd8 [libahci]
  LR is at ahci_deinit_port.constprop.12+0x1c/0xc0 [libahci]
    ...
  [<ffff000000a17014>] ahci_stop_engine+0x5c/0xd8 [libahci]
  [<ffff000000a196b4>] ahci_deinit_port.constprop.12+0x1c/0xc0 [libahci]
  [<ffff000000a197d8>] ahci_init_controller+0x80/0x168 [libahci]
  [<ffff000000a260f8>] ahci_pci_init_controller+0x60/0x68 [ahci]
  [<ffff000000a26f94>] ahci_init_one+0x75c/0xd88 [ahci]
  [<ffff000008430324>] local_pci_probe+0x3c/0xb8
  [<ffff000008431728>] pci_device_probe+0x138/0x170
  [<ffff000008585e54>] driver_probe_device+0x2dc/0x458
  [<ffff0000085860e4>] __driver_attach+0x114/0x118
  [<ffff000008583ca8>] bus_for_each_dev+0x60/0xa0
  [<ffff000008585638>] driver_attach+0x20/0x28
  [<ffff0000085850b0>] bus_add_driver+0x1f0/0x2a8
  [<ffff000008586ae0>] driver_register+0x60/0xf8
  [<ffff00000842f9b4>] __pci_register_driver+0x3c/0x48
  [<ffff000000a3001c>] ahci_pci_driver_init+0x1c/0x1000 [ahci]
  [<ffff000008083918>] do_one_initcall+0x38/0x120

where an obvious hardware level failure results in an unnecessary 15 second
delay and a subsequent crash.

So record the result code of ahci_reset_controller() and relay it, rather
than ignoring it.

Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
drivers/ata/ahci.c