usb: musb: musb_cppi41: handle pre-mature TX complete interrupt

usb: musb: musb_cppi41: handle pre-mature TX complete interrupt

commit a655f481d83d6d37bec0a2ddfdd24c30ff8f541f upstream.

The TX-complete interrupt of the CPPI41 on AM335x fires too early.
Adding a loop and counting how long it takes until the
MUSB_TXCSR_TXPKTRDY bit is cleared I see
FS:
|musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=64, mode=0, dma_addr=0xadc54002, len=1514 is_tx=1
|cppi41_dma_callback() 74 loops
|musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=64, mode=0, dma_addr=0xadcd8802, len=1514 is_tx=1
|cppi41_dma_callback() 66 loops
|musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=64, mode=0, dma_addr=0xadcd8002, len=1514 is_tx=1
|cppi41_dma_callback() 136 loops
|musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=64, mode=0, dma_addr=0xadf55802, len=1514 is_tx=1
|cppi41_dma_callback() 136 loops

avg: 110 - 150us

HS:
|musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=512, mode=0, dma_addr=0xaca6f002, len=1514 is_tx=1
|cppi41_dma_callback() 0 loops
|musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=512, mode=0, dma_addr=0xadd6f802, len=1514 is_tx=1
|cppi41_dma_callback() 2 loops
|musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=512, mode=0, dma_addr=0xadd6f002, len=1514 is_tx=1
|cppi41_dma_callback() 13 loops

avg: 2us

for the same test case. One loop means a udelay(1). The delay seems to
depend on the packet size. On HS the bit is always cleared for small
packet sizes while on FS it is never the case, it mostly around 110us.
This testing has been performed with g_ether (musb as device) and using BULK
transfers.

INTR transfers are way more fun: during init the gadget sends a INT
packet to the host and cppi41 says "transfer done" shortly after. The
MUSB_TXCSR_TXPKTRDY bit is set even seconds later. The reason is that the host
did not try to receive it, it does so after the interface (on host side) has
been configured. Until this happens, that packet remains in musb's FIFO.

To fix this, two things are done:
- No DMA transfers for INT based endpoints. These transfer are usually
  very small and rare so it is likely better to skip the DMA engine and
  stuff the four bytes directly into the FIFO
- on HS we poll up to 25us and hope that bit goes away. If not we setup
  a hrtimer to poll for it. The 140us delay is a rule of thumb. In FS
  the command
  | ping 10.10.10.10 -c1 -s65130
  creates about 44 1514bytes transfers. About 19 of them need a second
  timer to complete.

Reported-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>