X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2Fzynq-common.h;h=6574cf92e26ee1e5fa4c2465e4025952f1bae7bb;hb=aec118ebe63f7f0ab60916f9906fb3cb680abf7a;hp=7859b77603f113a08be7286a78e02b10402b1be7;hpb=8fba49bc8efb5ab5ee63666c0ab6cf2130fd3059;p=platform%2Fkernel%2Fu-boot.git

diff --git a/include/configs/zynq-common.h b/include/configs/zynq-common.h
index 7859b77..6574cf9 100644
--- a/include/configs/zynq-common.h
+++ b/include/configs/zynq-common.h
@@ -9,17 +9,8 @@
 #ifndef __CONFIG_ZYNQ_COMMON_H
 #define __CONFIG_ZYNQ_COMMON_H
 
-/* CPU clock */
-#ifndef CONFIG_CPU_FREQ_HZ
-# define CONFIG_CPU_FREQ_HZ	800000000
-#endif
-
-#define CONFIG_REMAKE_ELF
-
 /* Cache options */
-#define CONFIG_SYS_L2CACHE_OFF
 #ifndef CONFIG_SYS_L2CACHE_OFF
-# define CONFIG_SYS_L2_PL310
 # define CONFIG_SYS_PL310_BASE		0xf8f02000
 #endif
 
@@ -28,36 +19,28 @@
 #define CONFIG_SYS_TIMER_COUNTS_DOWN
 #define CONFIG_SYS_TIMER_COUNTER	(CONFIG_SYS_TIMERBASE + 0x4)
 
+/* GUIDs for capsule updatable firmware images */
+#define XILINX_BOOT_IMAGE_GUID \
+	EFI_GUID(0x1ba29a15, 0x9969, 0x40aa, 0xb4, 0x24, \
+		 0xe8, 0x61, 0x21, 0x61, 0x86, 0x64)
+
+#define XILINX_UBOOT_IMAGE_GUID \
+	EFI_GUID(0x1a5178f0, 0x87d3, 0x4f36, 0xac, 0x63, \
+		 0x3b, 0x31, 0xa2, 0x3b, 0xe3, 0x05)
+
 /* Serial drivers */
 /* The following table includes the supported baudrates */
 #define CONFIG_SYS_BAUDRATE_TABLE  \
 	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400}
 
 /* Ethernet driver */
-#if defined(CONFIG_ZYNQ_GEM)
-# define CONFIG_SYS_FAULT_ECHO_LINK_DOWN
-# define CONFIG_BOOTP_MAY_FAIL
-#endif
 
 /* NOR */
 #ifdef CONFIG_MTD_NOR_FLASH
-# define CONFIG_SYS_MAX_FLASH_BANKS	1
-# define CONFIG_SYS_MAX_FLASH_SECT	512
-# define CONFIG_SYS_FLASH_ERASE_TOUT	1000
-# define CONFIG_SYS_FLASH_WRITE_TOUT	5000
 # define CONFIG_FLASH_SHOW_PROGRESS	10
-# undef CONFIG_SYS_FLASH_EMPTY_INFO
-# define CONFIG_SYS_FLASH_QUIET_TEST
-#endif
-
-#ifdef CONFIG_NAND_ZYNQ
-#define CONFIG_SYS_MAX_NAND_DEVICE	1
-#define CONFIG_SYS_NAND_ONFI_DETECTION
 #endif
 
 #ifdef CONFIG_USB_EHCI_ZYNQ
-# define CONFIG_EHCI_IS_TDI
-
 # define DFU_DEFAULT_POLL_TIMEOUT	300
 # define CONFIG_THOR_RESET_OFF
 #endif
@@ -65,7 +48,6 @@
 /* enable preboot to be loaded before CONFIG_BOOTDELAY */
 
 /* Boot configuration */
-#define CONFIG_SYS_LOAD_ADDR		0 /* default? */
 
 #ifdef CONFIG_SPL_BUILD
 #define BOOTENV
@@ -207,38 +189,15 @@
 
 /* Miscellaneous configurable options */
 
-#define CONFIG_CLOCKS
-#define CONFIG_SYS_MAXARGS		32 /* max number of command args */
-#define CONFIG_SYS_CBSIZE		2048 /* Console I/O Buffer Size */
-
 #define CONFIG_SYS_INIT_RAM_ADDR	0xFFFF0000
 #define CONFIG_SYS_INIT_RAM_SIZE	0x2000
-#define CONFIG_SYS_INIT_SP_ADDR		(CONFIG_SYS_INIT_RAM_ADDR + \
-					CONFIG_SYS_INIT_RAM_SIZE - \
-					GENERATED_GBL_DATA_SIZE)
 
 
 /* Extend size of kernel image for uncompression */
-#define CONFIG_SYS_BOOTM_LEN	(60 * 1024 * 1024)
-
-/* Boot FreeBSD/vxWorks from an ELF image */
-#define CONFIG_SYS_MMC_MAX_DEVICE	1
-
-/* MMC support */
-#ifdef CONFIG_MMC_SDHCI_ZYNQ
-#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME     "u-boot.img"
-#endif
 
 /* Address in RAM where the parameters must be copied by SPL. */
-#define CONFIG_SYS_SPL_ARGS_ADDR	0x10000000
-
-#define CONFIG_SPL_FS_LOAD_ARGS_NAME		"system.dtb"
-#define CONFIG_SPL_FS_LOAD_KERNEL_NAME		"uImage"
 
 /* Not using MMC raw mode - just for compilation purpose */
-#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR	0
-#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS	0
-#define CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR	0
 
 /* qspi mode is working fine */
 #ifdef CONFIG_ZYNQ_QSPI
@@ -251,21 +210,13 @@
 /* SP location before relocation, must use scratch RAM */
 
 /* 3 * 64kB blocks of OCM - one is on the top because of bootrom */
-#define CONFIG_SPL_MAX_SIZE	0x30000
 
 /* On the top of OCM space */
-#define CONFIG_SYS_SPL_MALLOC_START	CONFIG_SPL_STACK_R_ADDR
-#define CONFIG_SYS_SPL_MALLOC_SIZE	0x2000000
 
 /*
  * SPL stack position - and stack goes down
  * 0xfffffe00 is used for putting wfi loop.
  * Set it up as limit for now.
  */
-#define CONFIG_SPL_STACK	0xfffffe00
-
-/* BSS setup */
-#define CONFIG_SPL_BSS_START_ADDR	0x100000
-#define CONFIG_SPL_BSS_MAX_SIZE		0x100000
 
 #endif /* __CONFIG_ZYNQ_COMMON_H */