X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2Fzmx25.h;h=c8b6161a299f78e125d4047bf8cd6f2d3eb73708;hb=2fe88d452268d61b5ca9cb0b1dda2974cc43faeb;hp=f669590fb70bdcf8700306da0400937a0fbd2393;hpb=43ade93bdb0c8bd57382be810a05b3793749ce85;p=platform%2Fkernel%2Fu-boot.git

diff --git a/include/configs/zmx25.h b/include/configs/zmx25.h
index f669590..c8b6161 100644
--- a/include/configs/zmx25.h
+++ b/include/configs/zmx25.h
@@ -1,10 +1,9 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
 /*
  * (c) 2011 Graf-Syteco, Matthias Weisser
  * <weisserm@arcor.de>
  *
  * Configuation settings for the zmx25 board
- *
- * SPDX-License-Identifier:	GPL-2.0+
  */
 
 #ifndef __CONFIG_H
@@ -12,9 +11,6 @@
 
 #include <asm/arch/imx-regs.h>
 
-#define CONFIG_MX25
-#define CONFIG_SYS_TEXT_BASE		0xA0000000
-
 #define CONFIG_SYS_TIMER_RATE		32768
 #define CONFIG_SYS_TIMER_COUNTER	\
 	(&((struct gpt_regs *)IMX_GPT1_BASE)->counter)
@@ -35,41 +31,25 @@
 #define CONFIG_INITRD_TAG
 
 /*
- * Compressions
- */
-#define CONFIG_LZO
-
-/*
  * Hardware drivers
  */
 
 /*
- * GPIO
- */
-#define CONFIG_MXC_GPIO
-
-/*
  * Serial
  */
 #define CONFIG_MXC_UART
 #define CONFIG_MXC_UART_BASE	UART2_BASE
-#define CONFIG_CONS_INDEX	1	/* use UART2 for console */
-#define CONFIG_BAUDRATE		115200	/* Default baud rate */
 
 /*
  * Ethernet
  */
 #define CONFIG_FEC_MXC
 #define CONFIG_FEC_MXC_PHYADDR		0x00
-#define CONFIG_MII
 
 /*
  * BOOTP options
  */
 #define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
 
 /*
  * Command line configuration.
@@ -83,18 +63,15 @@
  * USB
  */
 #ifdef CONFIG_CMD_USB
-#define CONFIG_USB_EHCI			/* Enable EHCI USB support */
 #define CONFIG_USB_EHCI_MXC
 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET
 #define CONFIG_MXC_USB_PORT	1
 #define CONFIG_MXC_USB_PORTSC	MXC_EHCI_MODE_SERIAL
 #define CONFIG_MXC_USB_FLAGS	(MXC_EHCI_INTERNAL_PHY | MXC_EHCI_IPPUE_DOWN)
 #define CONFIG_EHCI_IS_TDI
-#define CONFIG_SUPPORT_VFAT
 #endif /* CONFIG_CMD_USB */
 
 /* SDRAM */
-#define CONFIG_NR_DRAM_BANKS	1
 #define PHYS_SDRAM		0x80000000	/* start address of LPDDRRAM */
 #define PHYS_SDRAM_SIZE		0x04000000	/* 64 megs */
 
@@ -109,29 +86,18 @@
 #define CONFIG_SYS_MAX_FLASH_SECT	256
 
 #define CONFIG_ENV_ADDR			(CONFIG_SYS_FLASH_BASE + 0x00040000)
-#define CONFIG_ENV_IS_IN_FLASH		1
 #define CONFIG_ENV_SECT_SIZE		(128 * 1024)
 #define CONFIG_ENV_SIZE			(128 * 1024)
 
 /*
  * CFI FLASH driver setup
  */
-#define CONFIG_SYS_FLASH_CFI
-#define CONFIG_FLASH_CFI_DRIVER
-#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE	/* ~10x faster */
 
 #define CONFIG_SYS_LOAD_ADDR		CONFIG_SYS_SDRAM_BASE
 
 #define CONFIG_SYS_MEMTEST_START	(PHYS_SDRAM + (512*1024))
 #define CONFIG_SYS_MEMTEST_END		(PHYS_SDRAM + PHYS_SDRAM_SIZE)
 
-#define CONFIG_SYS_CBSIZE	256
-#define CONFIG_SYS_MAXARGS	16
-#define CONFIG_SYS_PBSIZE	(CONFIG_SYS_CBSIZE + \
-				sizeof(CONFIG_SYS_PROMPT) + 16)
-#define CONFIG_SYS_LONGHELP
-#define CONFIG_CMDLINE_EDITING
-
 #define CONFIG_PREBOOT  ""