X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2Fzeus.h;h=b653993700345362ccd85d1532e9aade18d7d3c4;hb=880540decfb855e96bc14ac84ac7784669e4b382;hp=6136af1fb2c945674d80650f65e3f91ccbf1f414;hpb=2ae1824196884ba2bafffb7c0d3e8297350591e9;p=platform%2Fkernel%2Fu-boot.git

diff --git a/include/configs/zeus.h b/include/configs/zeus.h
index 6136af1..b653993 100644
--- a/include/configs/zeus.h
+++ b/include/configs/zeus.h
@@ -53,7 +53,6 @@
 #define CONFIG_PHY_ADDR		0x01	/* PHY address			*/
 #define CONFIG_HAS_ETH1		1
 #define CONFIG_PHY1_ADDR	0x11	/* EMAC1 PHY address		*/
-#define CONFIG_NET_MULTI	1
 #define CONFIG_SYS_RX_ETH_BUFFER	16	/* Number of ethernet rx buffers & descriptors */
 #define CONFIG_PHY_RESET	1
 #define CONFIG_PHY_RESET_DELAY	300	/* PHY RESET recovery delay	*/
@@ -79,7 +78,6 @@
 #define CONFIG_CMD_ELF
 #define CONFIG_CMD_I2C
 #define CONFIG_CMD_IRQ
-#define CONFIG_CMD_LOG
 #define CONFIG_CMD_MII
 #define CONFIG_CMD_NET
 #define CONFIG_CMD_NFS
@@ -132,7 +130,6 @@
 #undef	CONFIG_SYS_EXT_SERIAL_CLOCK			/* external serial clock */
 #define CONFIG_SYS_BASE_BAUD	691200
 #define CONFIG_BAUDRATE		115200
-#define CONFIG_SERIAL_MULTI
 
 #define CONFIG_SYS_BAUDRATE_TABLE  \
     {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400}
@@ -171,11 +168,11 @@
 /*-----------------------------------------------------------------------
  * I2C
  *----------------------------------------------------------------------*/
-#define CONFIG_HARD_I2C		1		/* I2C with hardware support	*/
-#undef	CONFIG_SOFT_I2C				/* I2C bit-banged		*/
-#define CONFIG_PPC4XX_I2C		/* use PPC4xx driver		*/
-#define CONFIG_SYS_I2C_SPEED		400000		/* I2C speed and slave address	*/
-#define CONFIG_SYS_I2C_SLAVE		0x7F
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_PPC4XX
+#define CONFIG_SYS_I2C_PPC4XX_CH0
+#define CONFIG_SYS_I2C_PPC4XX_SPEED_0		400000
+#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0		0x7F
 
 /* these are for the ST M24C02 2kbit serial i2c eeprom */
 #define CONFIG_SYS_I2C_EEPROM_ADDR	0x50		/* base address */
@@ -253,10 +250,9 @@
 #define CONFIG_SYS_OCM_DATA_ADDR	0xF8000000
 #define CONFIG_SYS_OCM_DATA_SIZE	0x1000
 #define CONFIG_SYS_INIT_RAM_ADDR	CONFIG_SYS_OCM_DATA_ADDR /* inside of OCM		*/
-#define CONFIG_SYS_INIT_RAM_END	CONFIG_SYS_OCM_DATA_SIZE /* End of used area in RAM	*/
+#define CONFIG_SYS_INIT_RAM_SIZE	CONFIG_SYS_OCM_DATA_SIZE /* Size of used area in RAM	*/
 
-#define CONFIG_SYS_GBL_DATA_SIZE	128  /* size in bytes reserved for initial data */
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 /* reserve some memory for POST and BOOT limit info */
 #define CONFIG_SYS_INIT_SP_OFFSET	(CONFIG_SYS_GBL_DATA_OFFSET - 16)
 
@@ -304,14 +300,6 @@
 #define CONFIG_SYS_TIME_POST		5000
 #define CONFIG_SYS_TIME_FACTORY_RESET	10000
 
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD		0x01		/* Normal Power-On: Boot from FLASH	*/
-#define BOOTFLAG_WARM		0x02		/* Software reboot			*/
-
 #if defined(CONFIG_CMD_KGDB)
 #define CONFIG_KGDB_BAUDRATE	230400		/* speed to run kgdb serial port */
 #define CONFIG_KGDB_SER_INDEX	2		/* which serial port to use */