X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2Fyucca.h;h=b165bd7a118d330a004b61eb01a25cbe52f4e9f4;hb=cb5473205206c7f14cbb1e747f28ec75b48826e2;hp=7f8b0228aec2135be2f660d60f93d8e91bceaa69;hpb=f0da1d1b3c0719ea3b6025fe87b66224a466100d;p=platform%2Fkernel%2Fu-boot.git diff --git a/include/configs/yucca.h b/include/configs/yucca.h index 7f8b022..b165bd7 100644 --- a/include/configs/yucca.h +++ b/include/configs/yucca.h @@ -38,15 +38,19 @@ #define CONFIG_440 1 /* ... PPC440 family */ #define CONFIG_440SPE 1 /* Specifc SPe support */ #define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */ -#undef CFG_DRAM_TEST /* Disable-takes long time */ #define CONFIG_SYS_CLK_FREQ 33333333 /* external freq to pll */ #define EXTCLK_33_33 33333333 #define EXTCLK_66_66 66666666 #define EXTCLK_50 50000000 #define EXTCLK_83 83333333 +/* + * Include common defines/options for all AMCC eval boards + */ +#define CONFIG_HOSTNAME yucca +#include "amcc-common.h" + #define CONFIG_MISC_INIT_F 1 /* Use misc_init_f() */ -#define CONFIG_ADD_RAM_INFO 1 /* Print additional info */ #undef CONFIG_SHOW_BOOT_PROGRESS #undef CONFIG_STRESS @@ -54,66 +58,58 @@ * Base addresses -- Note these are effective addresses where the * actual resources get mapped (not physical addresses) *----------------------------------------------------------------------*/ -#define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */ -#define CFG_FLASH_BASE 0xfff00000 /* start of FLASH */ -#define CFG_MONITOR_BASE 0xfffb0000 /* start of monitor */ -#define CFG_PERIPHERAL_BASE 0xa0000000 /* internal peripherals */ -#define CFG_ISRAM_BASE 0x90000000 /* internal SRAM */ - -#define CFG_PCI_MEMBASE 0x80000000 /* mapped PCI memory */ -#define CFG_PCI_BASE 0xd0000000 /* internal PCI regs */ -#define CFG_PCI_TARGBASE CFG_PCI_MEMBASE - -#define CFG_PCIE_MEMBASE 0xb0000000 /* mapped PCIe memory */ -#define CFG_PCIE_MEMSIZE 0x01000000 -#define CFG_PCIE_BASE 0xe0000000 /* PCIe UTL regs */ - -#define CFG_PCIE0_CFGBASE 0xc0000000 -#define CFG_PCIE0_XCFGBASE 0xc0000400 -#define CFG_PCIE1_CFGBASE 0xc0001000 -#define CFG_PCIE1_XCFGBASE 0xc0001400 -#define CFG_PCIE2_CFGBASE 0xc0002000 -#define CFG_PCIE2_XCFGBASE 0xc0002400 +#define CONFIG_SYS_FLASH_BASE 0xfff00000 /* start of FLASH */ +#define CONFIG_SYS_PERIPHERAL_BASE 0xa0000000 /* internal peripherals */ +#define CONFIG_SYS_ISRAM_BASE 0x90000000 /* internal SRAM */ + +#define CONFIG_SYS_PCI_MEMBASE 0x80000000 /* mapped PCI memory */ +#define CONFIG_SYS_PCI_BASE 0xd0000000 /* internal PCI regs */ +#define CONFIG_SYS_PCI_TARGBASE CONFIG_SYS_PCI_MEMBASE + +#define CONFIG_SYS_PCIE_MEMBASE 0xb0000000 /* mapped PCIe memory */ +#define CONFIG_SYS_PCIE_MEMSIZE 0x08000000 /* smallest incr for PCIe port */ +#define CONFIG_SYS_PCIE_BASE 0xe0000000 /* PCIe UTL regs */ + +#define CONFIG_SYS_PCIE0_CFGBASE 0xc0000000 +#define CONFIG_SYS_PCIE1_CFGBASE 0xc1000000 +#define CONFIG_SYS_PCIE2_CFGBASE 0xc2000000 +#define CONFIG_SYS_PCIE0_XCFGBASE 0xc3000000 +#define CONFIG_SYS_PCIE1_XCFGBASE 0xc3001000 +#define CONFIG_SYS_PCIE2_XCFGBASE 0xc3002000 + +/* base address of inbound PCIe window */ +#define CONFIG_SYS_PCIE_INBOUND_BASE 0x0000000400000000ULL /* System RAM mapped to PCI space */ -#define CONFIG_PCI_SYS_MEM_BUS CFG_SDRAM_BASE -#define CONFIG_PCI_SYS_MEM_PHYS CFG_SDRAM_BASE +#define CONFIG_PCI_SYS_MEM_BUS CONFIG_SYS_SDRAM_BASE +#define CONFIG_PCI_SYS_MEM_PHYS CONFIG_SYS_SDRAM_BASE #define CONFIG_PCI_SYS_MEM_SIZE (1024 * 1024 * 1024) -#define CFG_FPGA_BASE 0xe2000000 /* epld */ -#define CFG_OPER_FLASH 0xe7000000 /* SRAM - OPER Flash */ +#define CONFIG_SYS_FPGA_BASE 0xe2000000 /* epld */ +#define CONFIG_SYS_OPER_FLASH 0xe7000000 /* SRAM - OPER Flash */ -/* #define CFG_NVRAM_BASE_ADDR 0x08000000 */ +/* #define CONFIG_SYS_NVRAM_BASE_ADDR 0x08000000 */ /*----------------------------------------------------------------------- * Initial RAM & stack pointer (placed in internal SRAM) *----------------------------------------------------------------------*/ -#define CFG_TEMP_STACK_OCM 1 -#define CFG_OCM_DATA_ADDR CFG_ISRAM_BASE -#define CFG_INIT_RAM_ADDR CFG_ISRAM_BASE /* Initial RAM address */ -#define CFG_INIT_RAM_END 0x2000 /* End of used area in RAM */ -#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */ - -#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) -#define CFG_POST_WORD_ADDR (CFG_GBL_DATA_OFFSET - 0x4) -#define CFG_INIT_SP_OFFSET CFG_POST_WORD_ADDR +#define CONFIG_SYS_TEMP_STACK_OCM 1 +#define CONFIG_SYS_OCM_DATA_ADDR CONFIG_SYS_ISRAM_BASE +#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_ISRAM_BASE /* Initial RAM address */ +#define CONFIG_SYS_INIT_RAM_END 0x2000 /* End of used area in RAM */ +#define CONFIG_SYS_GBL_DATA_SIZE 128 /* num bytes initial data */ -#define CFG_MONITOR_LEN (320 * 1024) /* Reserve 320 kB for Mon */ -#define CFG_MALLOC_LEN (512 * 1024) /* Reserve 512 kB for malloc */ +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) +#define CONFIG_SYS_POST_WORD_ADDR (CONFIG_SYS_GBL_DATA_OFFSET - 0x4) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_POST_WORD_ADDR /*----------------------------------------------------------------------- * Serial Port *----------------------------------------------------------------------*/ -#define CONFIG_SERIAL_MULTI 1 #undef CONFIG_UART1_CONSOLE #undef CONFIG_SERIAL_SOFTWARE_FIFO -#undef CFG_EXT_SERIAL_CLOCK -/* #define CFG_EXT_SERIAL_CLOCK (1843200 * 6) */ /* Ext clk @ 11.059 MHz */ - -#define CONFIG_BAUDRATE 115200 - -#define CFG_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} +#undef CONFIG_SYS_EXT_SERIAL_CLOCK +/* #define CONFIG_SYS_EXT_SERIAL_CLOCK (1843200 * 6) */ /* Ext clk @ 11.059 MHz */ /*----------------------------------------------------------------------- * DDR SDRAM @@ -125,159 +121,79 @@ /*----------------------------------------------------------------------- * I2C *----------------------------------------------------------------------*/ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ -#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CFG_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ #define IIC0_BOOTPROM_ADDR 0x50 #define IIC0_ALT_BOOTPROM_ADDR 0x54 /* Don't probe these addrs */ -#define CFG_I2C_NOPROBES {0x50, 0x52, 0x53, 0x54} +#define CONFIG_SYS_I2C_NOPROBES {0x50, 0x52, 0x53, 0x54} -/* #if (CONFIG_COMMANDS & CFG_CMD_EEPROM) */ -/* #define CFG_I2C_EEPROM_ADDR 0x50 */ /* I2C boot EEPROM */ -#define CFG_I2C_EEPROM_ADDR_LEN 2 /* Bytes of address */ +/* #if defined(CONFIG_CMD_EEPROM) */ +/* #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 */ /* I2C boot EEPROM */ +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 /* Bytes of address */ /* #endif */ /*----------------------------------------------------------------------- * Environment *----------------------------------------------------------------------*/ -/* #define CFG_NVRAM_SIZE (0x2000 - 8) */ /* NVRAM size(8k)- RTC regs */ +/* #define CONFIG_SYS_NVRAM_SIZE (0x2000 - 8) */ /* NVRAM size(8k)- RTC regs */ -#undef CFG_ENV_IS_IN_NVRAM /* ... not in NVRAM */ -#define CFG_ENV_IS_IN_FLASH 1 /* Environment uses flash */ -#undef CFG_ENV_IS_IN_EEPROM /* ... not in EEPROM */ +#undef CONFIG_ENV_IS_IN_NVRAM /* ... not in NVRAM */ +#define CONFIG_ENV_IS_IN_FLASH 1 /* Environment uses flash */ +#undef CONFIG_ENV_IS_IN_EEPROM /* ... not in EEPROM */ #define CONFIG_ENV_OVERWRITE 1 -#define CONFIG_PREBOOT "echo;" \ - "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \ - "echo" - -#undef CONFIG_BOOTARGS - +/* + * Default environment variables + */ #define CONFIG_EXTRA_ENV_SETTINGS \ - "netdev=eth0\0" \ - "hostname=yucca\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=${serverip}:${rootpath}\0" \ - "ramargs=setenv bootargs root=/dev/ram rw\0" \ - "addip=setenv bootargs ${bootargs} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ - ":${hostname}:${netdev}:off panic=1\0" \ - "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\ - "flash_nfs=run nfsargs addip addtty;" \ - "bootm ${kernel_addr}\0" \ - "flash_self=run ramargs addip addtty;" \ - "bootm ${kernel_addr} ${ramdisk_addr}\0" \ - "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \ - "bootm\0" \ - "rootpath=/opt/eldk/ppc_4xx\0" \ - "bootfile=yucca/uImage\0" \ + CONFIG_AMCC_DEF_ENV \ + CONFIG_AMCC_DEF_ENV_PPC \ + CONFIG_AMCC_DEF_ENV_NOR_UPD \ "kernel_addr=E7F10000\0" \ "ramdisk_addr=E7F20000\0" \ - "initrd_high=30000000\0" \ - "load=tftp 100000 yuca/u-boot.bin\0" \ - "update=protect off 2:4-7;era 2:4-7;" \ - "cp.b ${fileaddr} FFFB0000 ${filesize};" \ - "setenv filesize;saveenv\0" \ - "upd=run load;run update\0" \ + "pciconfighost=1\0" \ + "pcie_mode=RP:EP:EP\0" \ "" -#define CONFIG_BOOTCOMMAND "run flash_self" - -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ - -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ - -#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \ - CFG_CMD_ASKENV | \ - CFG_CMD_EEPROM | \ - CFG_CMD_DHCP | \ - CFG_CMD_DIAG | \ - CFG_CMD_ELF | \ - CFG_CMD_I2C | \ - CFG_CMD_IRQ | \ - CFG_CMD_MII | \ - CFG_CMD_NET | \ - CFG_CMD_NFS | \ - CFG_CMD_PCI | \ - CFG_CMD_PING | \ - CFG_CMD_REGINFO | \ - CFG_CMD_SDRAM ) - -/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ -#include + +/* + * Commands additional to the ones defined in amcc-common.h + */ +#define CONFIG_CMD_PCI +#define CONFIG_CMD_SDRAM #define CONFIG_IBM_EMAC4_V4 1 -#define CONFIG_MII 1 /* MII PHY management */ -#undef CONFIG_NET_MULTI #define CONFIG_PHY_ADDR 1 /* PHY address, See schematics */ #define CONFIG_HAS_ETH0 #define CONFIG_PHY_RESET 1 /* reset phy upon startup */ #define CONFIG_PHY_RESET_DELAY 1000 #define CONFIG_CIS8201_PHY 1 /* Enable 'special' RGMII mode for Cicada phy */ #define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */ -#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */ - -#define CONFIG_NETCONSOLE /* include NetConsole support */ -#define CONFIG_NET_MULTI /* needed for NetConsole */ - -#undef CONFIG_WATCHDOG /* watchdog disabled */ - -/* - * Miscellaneous configurable options - */ -#define CFG_LONGHELP /* undef to save memory */ -#define CFG_PROMPT "=> " /* Monitor Command Prompt */ - -#if (CONFIG_COMMANDS & CFG_CMD_KGDB) -#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ - -#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ -#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ - -#define CFG_LOAD_ADDR 0x100000 /* default load address */ -#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */ - -#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ - -#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ -#define CONFIG_LOOPW 1 /* enable loopw command */ -#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */ -#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ -#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ /*----------------------------------------------------------------------- * FLASH related *----------------------------------------------------------------------*/ -#define CFG_MAX_FLASH_BANKS 3 /* number of banks */ -#define CFG_MAX_FLASH_SECT 256 /* sectors per device */ - -#undef CFG_FLASH_CHECKSUM -#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ -#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ - -#define CFG_FLASH_ADDR0 0x5555 -#define CFG_FLASH_ADDR1 0x2aaa -#define CFG_FLASH_WORD_SIZE unsigned char - -#define CFG_FLASH_2ND_16BIT_DEV 1 /* evb440SPe has 8 and 16bit device */ -#define CFG_FLASH_2ND_ADDR 0xe7c00000 /* evb440SPe has 8 and 16bit device*/ - -#ifdef CFG_ENV_IS_IN_FLASH -#define CFG_ENV_SECT_SIZE 0x10000 /* size of one complete sector */ -#define CFG_ENV_ADDR 0xfffa0000 -/* #define CFG_ENV_ADDR (CFG_MONITOR_BASE-CFG_ENV_SECT_SIZE) */ -#define CFG_ENV_SIZE 0x10000 /* Size of Environment vars */ -#endif /* CFG_ENV_IS_IN_FLASH */ +#define CONFIG_SYS_MAX_FLASH_BANKS 3 /* number of banks */ +#define CONFIG_SYS_MAX_FLASH_SECT 256 /* sectors per device */ + +#undef CONFIG_SYS_FLASH_CHECKSUM +#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ +#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ + +#define CONFIG_SYS_FLASH_ADDR0 0x5555 +#define CONFIG_SYS_FLASH_ADDR1 0x2aaa +#define CONFIG_SYS_FLASH_WORD_SIZE unsigned char + +#define CONFIG_SYS_FLASH_2ND_16BIT_DEV 1 /* evb440SPe has 8 and 16bit device */ +#define CONFIG_SYS_FLASH_2ND_ADDR 0xe7c00000 /* evb440SPe has 8 and 16bit device*/ + +#ifdef CONFIG_ENV_IS_IN_FLASH +#define CONFIG_ENV_SECT_SIZE 0x10000 /* size of one complete sector */ +#define CONFIG_ENV_ADDR 0xfffa0000 +/* #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE-CONFIG_ENV_SECT_SIZE) */ +#define CONFIG_ENV_SIZE 0x10000 /* Size of Environment vars */ +#endif /* CONFIG_ENV_IS_IN_FLASH */ /*----------------------------------------------------------------------- * PCI stuff *----------------------------------------------------------------------- @@ -286,16 +202,15 @@ #define CONFIG_PCI /* include pci support */ #define CONFIG_PCI_PNP 1 /* do pci plug-and-play */ #define CONFIG_PCI_SCAN_SHOW 1 /* show pci devices on startup */ -#undef CONFIG_PCI_CONFIG_HOST_BRIDGE +#define CONFIG_PCI_CONFIG_HOST_BRIDGE /* Board-specific PCI */ -#define CFG_PCI_PRE_INIT 1 /* enable board pci_pre_init() */ -#define CFG_PCI_TARGET_INIT /* let board init pci target */ -#undef CFG_PCI_MASTER_INIT +#define CONFIG_SYS_PCI_TARGET_INIT /* let board init pci target */ +#undef CONFIG_SYS_PCI_MASTER_INIT -#define CFG_PCI_SUBSYS_VENDORID 0x1014 /* IBM */ -#define CFG_PCI_SUBSYS_DEVICEID 0xcafe /* Whatever */ -/* #define CFG_PCI_SUBSYS_ID CFG_PCI_SUBSYS_DEVICEID */ +#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1014 /* IBM */ +#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0xcafe /* Whatever */ +/* #define CONFIG_SYS_PCI_SUBSYS_ID CONFIG_SYS_PCI_SUBSYS_DEVICEID */ /* * NETWORK Support (PCI): @@ -303,34 +218,6 @@ /* Support for Intel 82557/82559/82559ER chips. */ #define CONFIG_EEPRO100 -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CFG_BOOTMAPSZ (8 << 20) /*Initial Memory map for Linux*/ -/*----------------------------------------------------------------------- - * Cache Configuration - */ -#define CFG_DCACHE_SIZE 8192 /* For AMCC 405 CPUs */ -#define CFG_CACHELINE_SIZE 32 /* ... */ -#if (CONFIG_COMMANDS & CFG_CMD_KGDB) -#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -#endif - -/* - * Internal Definitions - * - * Boot Flags - */ -#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ -#define BOOTFLAG_WARM 0x02 /* Software reboot */ - -#if (CONFIG_COMMANDS & CFG_CMD_KGDB) -#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ -#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ -#endif - /* FB Divisor selection */ #define FPGA_FB_DIV_6 6 #define FPGA_FB_DIV_10 10 @@ -532,6 +419,4 @@ #define PERIOD_33_33MHZ 30000 /* 30ns */ #define PERIOD_25_00MHZ 40000 /* 40ns */ -/*---------------------------------------------------------------------------*/ - #endif /* __CONFIG_H */