X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2Fyucca.h;h=9c536fd12da9cd17a5a185a7670d63351c520cbd;hb=375c2c9e57ea5b8d678475379378f4774aa9cb88;hp=eb4859c3e97162056e1656a2e474593f24be7caf;hpb=f6d3faae792be848567688df7ea3f803c25af5b2;p=platform%2Fkernel%2Fu-boot.git

diff --git a/include/configs/yucca.h b/include/configs/yucca.h
index eb4859c..9c536fd 100644
--- a/include/configs/yucca.h
+++ b/include/configs/yucca.h
@@ -120,7 +120,7 @@
  *----------------------------------------------------------------------*/
 #define CONFIG_SPD_EEPROM	1	/* Use SPD EEPROM for setup	*/
 #define SPD_EEPROM_ADDRESS	{0x53, 0x52}	/* SPD i2c spd addresses*/
-#undef CONFIG_DDR_ECC			/* no ECC support for now	*/
+#define CONFIG_DDR_ECC		1	/* with ECC support		*/
 
 /*-----------------------------------------------------------------------
  * I2C
@@ -136,7 +136,7 @@
 /* Don't probe these addrs */
 #define CFG_I2C_NOPROBES	{0x50, 0x52, 0x53, 0x54}
 
-/* #if (CONFIG_COMMANDS & CFG_CMD_EEPROM) */
+/* #if defined(CONFIG_CMD_EEPROM) */
 /* #define CFG_I2C_EEPROM_ADDR	0x50 */	/* I2C boot EEPROM		*/
 #define CFG_I2C_EEPROM_ADDR_LEN	2	/* Bytes of address		*/
 /* #endif */
@@ -191,24 +191,36 @@
 #define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
 #define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/
 
-#define CONFIG_COMMANDS	       (CONFIG_CMD_DFL	| \
-				CFG_CMD_ASKENV	| \
-				CFG_CMD_EEPROM	| \
-				CFG_CMD_DHCP	| \
-				CFG_CMD_DIAG	| \
-				CFG_CMD_ELF	| \
-				CFG_CMD_I2C	| \
-				CFG_CMD_IRQ	| \
-				CFG_CMD_MII	| \
-				CFG_CMD_NET	| \
-				CFG_CMD_NFS	| \
-				CFG_CMD_PCI	| \
-				CFG_CMD_PING	| \
-				CFG_CMD_REGINFO	| \
-				CFG_CMD_SDRAM	)
-
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_ASKENV
+#define CONFIG_CMD_EEPROM
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_DIAG
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_IRQ
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_NFS
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_REGINFO
+#define CONFIG_CMD_SDRAM
+
 
 #define	CONFIG_IBM_EMAC4_V4	1
 #define CONFIG_MII		1	/* MII PHY management		*/
@@ -232,7 +244,7 @@
 #define CFG_LONGHELP				/* undef to save memory		*/
 #define CFG_PROMPT		"=> "		/* Monitor Command Prompt	*/
 
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
 #define CFG_CBSIZE		1024		/* Console I/O Buffer Size	*/
 #else
 #define CFG_CBSIZE		256		/* Console I/O Buffer Size	*/
@@ -289,7 +301,6 @@
 #undef CONFIG_PCI_CONFIG_HOST_BRIDGE
 
 /* Board-specific PCI */
-#define CFG_PCI_PRE_INIT	1	/* enable board pci_pre_init()	*/
 #define CFG_PCI_TARGET_INIT		/* let board init pci target    */
 #undef	CFG_PCI_MASTER_INIT
 
@@ -314,7 +325,7 @@
  */
 #define CFG_DCACHE_SIZE		8192	/* For AMCC 405 CPUs		*/
 #define CFG_CACHELINE_SIZE	32	/* ...				*/
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
 #define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value */
 #endif
 
@@ -326,7 +337,7 @@
 #define BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH */
 #define BOOTFLAG_WARM	0x02		/* Software reboot */
 
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
 #define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
 #define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
 #endif