X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2Fyosemite.h;h=cb2042ce6ce0fb9f5113cce4e1e4235ed43c0898;hb=28ac6719108e989429de2b3dfa90312ba7c4d27b;hp=dd6d9acdd5de4163f8471289286d07e8fd60f9de;hpb=2c4faea84f3d96d674e3c065e1f220b20c8930c0;p=platform%2Fkernel%2Fu-boot.git diff --git a/include/configs/yosemite.h b/include/configs/yosemite.h index dd6d9ac..cb2042c 100644 --- a/include/configs/yosemite.h +++ b/include/configs/yosemite.h @@ -42,6 +42,11 @@ #define CONFIG_4xx 1 /* ... PPC4xx family */ #define CONFIG_SYS_CLK_FREQ 66666666 /* external freq to pll */ +/* + * Include common defines/options for all AMCC eval boards + */ +#include "amcc-common.h" + #define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */ #define CONFIG_MISC_INIT_R 1 /* call misc_init_r() */ #define CONFIG_BOARD_RESET 1 /* call board_reset() */ @@ -50,10 +55,6 @@ * Base addresses -- Note these are effective addresses where the * actual resources get mapped (not physical addresses) *----------------------------------------------------------------------*/ -#define CFG_MONITOR_LEN (512 * 1024) /* Reserve 512 kB for Monitor */ -#define CFG_MALLOC_LEN (256 * 1024) /* Reserve 256 kB for malloc() */ -#define CFG_MONITOR_BASE (-CFG_MONITOR_LEN) -#define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */ #define CFG_FLASH_BASE 0xfc000000 /* start of FLASH */ #define CFG_PCI_MEMBASE 0xa0000000 /* mapped pci memory*/ #define CFG_PCI_MEMBASE1 CFG_PCI_MEMBASE + 0x10000000 @@ -75,7 +76,7 @@ *----------------------------------------------------------------------*/ #define CFG_INIT_RAM_DCACHE 1 /* d-cache as init ram */ #define CFG_INIT_RAM_ADDR 0x70000000 /* DCache */ -#define CFG_INIT_RAM_END (8 << 10) +#define CFG_INIT_RAM_END (4 << 10) #define CFG_GBL_DATA_SIZE 256 /* num bytes initial data*/ #define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) #define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET @@ -84,14 +85,9 @@ * Serial Port *----------------------------------------------------------------------*/ #define CFG_EXT_SERIAL_CLOCK 11059200 /* use external 11.059MHz clk */ -#define CONFIG_BAUDRATE 115200 -#define CONFIG_SERIAL_MULTI 1 /*define this if you want console on UART1*/ #undef CONFIG_UART1_CONSOLE -#define CFG_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} - /*----------------------------------------------------------------------- * Environment *----------------------------------------------------------------------*/ @@ -109,7 +105,7 @@ * FLASH related *----------------------------------------------------------------------*/ #define CFG_FLASH_CFI /* The flash is CFI compatible */ -#define CFG_FLASH_CFI_DRIVER /* Use common CFI driver */ +#define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver */ #define CFG_FLASH_CFI_AMD_RESET 1 /* AMD RESET for STM 29W320DB! */ #define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */ @@ -139,14 +135,10 @@ #define CFG_KBYTES_SDRAM (128 * 1024) /* 128MB */ #define CFG_SDRAM_BANKS (2) - /*----------------------------------------------------------------------- * I2C *----------------------------------------------------------------------*/ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ #define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CFG_I2C_SLAVE 0x7F #define CFG_I2C_MULTI_EEPROMS #define CFG_I2C_EEPROM_ADDR (0xa8>>1) @@ -160,71 +152,30 @@ #define CFG_ENV_OFFSET 0x0 #endif /* CFG_ENV_IS_IN_EEPROM */ -#define CONFIG_PREBOOT "echo;" \ - "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \ - "echo" - -#undef CONFIG_BOOTARGS - -/* Setup some board specific values for the default environment variables */ -#ifndef CONFIG_YELLOWSTONE -#define CONFIG_HOSTNAME yosemite -#define CFG_BOOTFILE "bootfile=/tftpboot/yosemite/uImage\0" -#define CFG_ROOTPATH "rootpath=/opt/eldk/ppc_4xxFP\0" -#else -#define CONFIG_HOSTNAME yellowstone -#define CFG_BOOTFILE "bootfile=/tftpboot/yellowstone/uImage\0" -#define CFG_ROOTPATH "rootpath=/opt/eldk/ppc_4xx\0" -#endif +/* I2C SYSMON (LM75, AD7414 is almost compatible) */ +#define CONFIG_DTT_LM75 1 /* ON Semi's LM75 */ +#define CONFIG_DTT_AD7414 1 /* use AD7414 */ +#define CONFIG_DTT_SENSORS {0} /* Sensor addresses */ +#define CFG_DTT_MAX_TEMP 70 +#define CFG_DTT_LOW_TEMP -30 +#define CFG_DTT_HYSTERESIS 3 +/* + * Default environment variables + */ #define CONFIG_EXTRA_ENV_SETTINGS \ - CFG_BOOTFILE \ - CFG_ROOTPATH \ - "netdev=eth0\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=${serverip}:${rootpath}\0" \ - "ramargs=setenv bootargs root=/dev/ram rw\0" \ - "addip=setenv bootargs ${bootargs} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ - ":${hostname}:${netdev}:off panic=1\0" \ - "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\ - "flash_nfs=run nfsargs addip addtty;" \ - "bootm ${kernel_addr}\0" \ - "flash_self=run ramargs addip addtty;" \ - "bootm ${kernel_addr} ${ramdisk_addr}\0" \ - "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \ - "bootm\0" \ - "bootfile=/tftpboot/${hostname}/uImage\0" \ + CONFIG_AMCC_DEF_ENV \ + CONFIG_AMCC_DEF_ENV_POWERPC \ + CONFIG_AMCC_DEF_ENV_PPC_OLD \ + CONFIG_AMCC_DEF_ENV_NOR_UPD \ "kernel_addr=fc000000\0" \ "ramdisk_addr=fc180000\0" \ - "load=tftp 200000 /tftpboot/${hostname}/u-boot.bin\0" \ - "update=protect off fff80000 ffffffff;era fff80000 ffffffff;" \ - "cp.b 200000 fff80000 80000;" \ - "setenv filesize;saveenv\0" \ - "upd=run load;run update\0" \ "" -#define CONFIG_BOOTCOMMAND "run flash_self" - -#if 0 -#define CONFIG_BOOTDELAY -1 /* autoboot disabled */ -#else -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ -#endif -#define CONFIG_BAUDRATE 115200 - -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ - -#define CONFIG_MII 1 /* MII PHY management */ -#define CONFIG_NET_MULTI 1 /* required for netconsole */ -#define CONFIG_PHY1_ADDR 3 +#define CONFIG_HAS_ETH0 1 /* add support for "ethaddr" */ #define CONFIG_HAS_ETH1 1 /* add support for "eth1addr" */ #define CONFIG_PHY_ADDR 1 /* PHY address, See schematics */ - -#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */ - -#define CONFIG_NETCONSOLE /* include NetConsole support */ +#define CONFIG_PHY1_ADDR 3 /* Partitions */ #define CONFIG_MAC_PARTITION @@ -233,8 +184,15 @@ #ifdef CONFIG_440EP /* USB */ -#define CONFIG_USB_OHCI +#define CONFIG_USB_OHCI_NEW #define CONFIG_USB_STORAGE +#define CFG_OHCI_BE_CONTROLLER + +#undef CFG_USB_OHCI_BOARD_INIT +#define CFG_USB_OHCI_CPU_INIT 1 +#define CFG_USB_OHCI_REGS_BASE (CFG_PERIPHERAL_BASE | 0x1000) +#define CFG_USB_OHCI_SLOT_NAME "ppc440" +#define CFG_USB_OHCI_MAX_ROOT_PORTS 15 /* Comment this out to enable USB 1.1 device */ #define USB_2_0_DEVICE @@ -248,35 +206,11 @@ #define CONFIG_HW_WATCHDOG /* watchdog */ #endif - /* - * BOOTP options + * Commands additional to the ones defined in amcc-common.h */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - - -/* - * Command line configuration. - */ -#include - -#define CONFIG_CMD_ASKENV -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_DIAG -#define CONFIG_CMD_ELF -#define CONFIG_CMD_EEPROM -#define CONFIG_CMD_I2C -#define CONFIG_CMD_IRQ -#define CONFIG_CMD_MII -#define CONFIG_CMD_NET -#define CONFIG_CMD_NFS +#define CONFIG_CMD_DTT #define CONFIG_CMD_PCI -#define CONFIG_CMD_PING -#define CONFIG_CMD_REGINFO -#define CONFIG_CMD_SDRAM #ifdef CONFIG_440EP #define CONFIG_CMD_USB @@ -284,36 +218,6 @@ #define CONFIG_CMD_EXT2 #endif - -/* - * Miscellaneous configurable options - */ -#define CFG_LONGHELP /* undef to save memory */ -#define CFG_PROMPT "=> " /* Monitor Command Prompt */ -#if defined(CONFIG_CMD_KGDB) -#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ - -#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ -#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ - -#define CFG_LOAD_ADDR 0x100000 /* default load address */ -#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */ -#define CONFIG_LYNXKDI 1 /* support kdi files */ - -#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ - -#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ -#define CONFIG_LOOPW 1 /* enable loopw command */ -#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */ -#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ -#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ - /*----------------------------------------------------------------------- * PCI stuff *----------------------------------------------------------------------- @@ -331,13 +235,6 @@ #define CFG_PCI_SUBSYS_VENDORID 0x10e8 /* AMCC */ #define CFG_PCI_SUBSYS_ID 0xcafe /* Whatever */ -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - /*----------------------------------------------------------------------- * External Bus Controller (EBC) Setup *----------------------------------------------------------------------*/ @@ -352,26 +249,6 @@ #define CFG_EBC_PB2AP 0x04814500 #define CFG_EBC_PB2CR (CFG_CPLD | 0x18000) -/*----------------------------------------------------------------------- - * Cache Configuration - */ -#define CFG_DCACHE_SIZE (32<<10) /* For AMCC 440 CPUs */ -#define CFG_CACHELINE_SIZE 32 /* ... */ -#if defined(CONFIG_CMD_KGDB) -#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -#endif - -/* - * Internal Definitions - * - * Boot Flags - */ -#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ -#define BOOTFLAG_WARM 0x02 /* Software reboot */ - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ -#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ -#endif +#define CFG_BCSR5_PCI66EN 0x80 #endif /* __CONFIG_H */