X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2Fxpedite550x.h;h=6346f849d46d283d9b38511d36e747db66dcef19;hb=b0cf733933c3bc1b4ab353e16affabc60f863db5;hp=ac3f4f1c84a3ac5f883971325480520996044bba;hpb=692e5c4e7eb267f3d8f3a8c9d2348eff6f5f21e2;p=platform%2Fkernel%2Fu-boot.git

diff --git a/include/configs/xpedite550x.h b/include/configs/xpedite550x.h
index ac3f4f1..6346f84 100644
--- a/include/configs/xpedite550x.h
+++ b/include/configs/xpedite550x.h
@@ -14,30 +14,22 @@
 /*
  * High Level Configuration Options
  */
-#define CONFIG_BOOKE		1	/* BOOKE */
-#define CONFIG_E500		1	/* BOOKE e500 family */
-#define CONFIG_P2020		1
 #define CONFIG_XPEDITE550X	1
 #define CONFIG_SYS_BOARD_NAME	"XPedite5500"
 #define CONFIG_SYS_FORM_PMC_XMC	1
 #define CONFIG_PRPMC_PCI_ALIAS	"pci0"	/* Processor PMC interface on pci0 */
 #define CONFIG_BOARD_EARLY_INIT_R	/* Call board_pre_init */
-#define CONFIG_SYS_GENERIC_BOARD
-#define CONFIG_DISPLAY_BOARDINFO
 
 #ifndef CONFIG_SYS_TEXT_BASE
 #define CONFIG_SYS_TEXT_BASE	0xfff80000
 #endif
 
-#define CONFIG_PCI		1	/* Enable PCI/PCIE */
-#define CONFIG_PCI_PNP		1	/* do pci plug-and-play */
 #define CONFIG_PCI_SCAN_SHOW	1	/* show pci devices on startup */
-#define CONFIG_PCIE1		1	/* PCIE controler 1 (PEX8112 or XMC) */
+#define CONFIG_PCIE1		1	/* PCIE controller 1 (PEX8112 or XMC) */
 #define CONFIG_FSL_PCI_INIT	1	/* Use common FSL init code */
 #define CONFIG_PCI_INDIRECT_BRIDGE 1	/* indirect PCI bridge support */
 #define CONFIG_SYS_PCI_64BIT	1	/* enable 64-bit PCI resources */
 #define CONFIG_FSL_PCIE_RESET	1	/* need PCIe reset errata */
-#define CONFIG_FSL_LAW		1	/* Use common FSL init code */
 #define CONFIG_FSL_ELBC		1
 
 /*
@@ -50,13 +42,11 @@
 /*
  * DDR config
  */
-#define CONFIG_SYS_FSL_DDR3
 #define CONFIG_SPD_EEPROM		/* Use SPD EEPROM for DDR setup */
 #define CONFIG_DDR_SPD
 #define CONFIG_MEM_INIT_VALUE		0xdeadbeef
 #define SPD_EEPROM_ADDRESS			0x54
 #define SPD_EEPROM_OFFSET		0x200	/* OFFSET of SPD in EEPROM */
-#define CONFIG_NUM_DDR_CONTROLLERS	1
 #define CONFIG_DIMM_SLOTS_PER_CTLR	1
 #define CONFIG_CHIP_SELECTS_PER_CTRL 2
 #define CONFIG_DDR_ECC
@@ -122,7 +112,6 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy);
 #define CONFIG_SYS_NAND_BASE_LIST	{CONFIG_SYS_NAND_BASE, \
 					 CONFIG_SYS_NAND_BASE2}
 #define CONFIG_SYS_MAX_NAND_DEVICE	2
-#define CONFIG_SYS_NAND_QUIET_TEST	/* 2nd NAND flash not always populated */
 #define CONFIG_NAND_FSL_ELBC
 
 /*
@@ -206,7 +195,6 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy);
  * Serial Port
  */
 #define CONFIG_CONS_INDEX		1
-#define CONFIG_SYS_NS16550
 #define CONFIG_SYS_NS16550_SERIAL
 #define CONFIG_SYS_NS16550_REG_SIZE	1
 #define CONFIG_SYS_NS16550_CLK		get_bus_freq(0)
@@ -218,17 +206,6 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy);
 #define CONFIG_LOADS_ECHO		1	/* echo on for serial download */
 #define CONFIG_SYS_LOADS_BAUD_CHANGE	1	/* allow baudrate change */
 
-/*
- * Use the HUSH parser
- */
-#define CONFIG_SYS_HUSH_PARSER
-
-/*
- * Pass open firmware flat tree
- */
-#define CONFIG_OF_LIBFDT		1
-#define CONFIG_OF_BOARD_SETUP		1
-#define CONFIG_OF_STDOUT_VIA_ALIAS	1
 #define CONFIG_FDT_FIXUP_PCI_IRQ	1
 
 /*
@@ -313,7 +290,6 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy);
 #define CONFIG_SYS_PCIE1_IO_PHYS	0xe8000000
 #define CONFIG_SYS_PCIE1_IO_SIZE	0x00800000	/* 8M */
 
-
 /*
  * Networking options
  */
@@ -358,38 +334,23 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy);
 /*
  * USB
  */
-#define CONFIG_USB_STORAGE
 #define CONFIG_USB_EHCI
 #define CONFIG_USB_EHCI_FSL
 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET
-#define CONFIG_DOS_PARTITION
 
 /*
  * Command configuration.
  */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
 #define CONFIG_CMD_DATE
-#define CONFIG_CMD_DHCP
 #define CONFIG_CMD_DTT
 #define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_FLASH
-#define CONFIG_CMD_I2C
 #define CONFIG_CMD_JFFS2
-#define CONFIG_CMD_MII
 #define CONFIG_CMD_NAND
-#define CONFIG_CMD_NET
 #define CONFIG_CMD_PCA953X
 #define CONFIG_CMD_PCA953X_INFO
 #define CONFIG_CMD_PCI
 #define CONFIG_CMD_PCI_ENUM
-#define CONFIG_CMD_PING
 #define CONFIG_CMD_REGINFO
-#define CONFIG_CMD_SAVEENV
-#define CONFIG_CMD_SNTP
-#define CONFIG_CMD_USB
 
 /*
  * Miscellaneous configurable options
@@ -403,11 +364,8 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy);
 #define CONFIG_CMDLINE_EDITING	1		/* add command line history	*/
 #define CONFIG_AUTO_COMPLETE	1		/* add autocompletion support */
 #define CONFIG_LOADADDR		0x1000000	/* default location for tftp and bootm */
-#define CONFIG_BOOTDELAY	3		/* -1 disables auto-boot */
 #define CONFIG_PANIC_HANG			/* do not reset board on panic */
 #define CONFIG_PREBOOT				/* enable preboot variable */
-#define CONFIG_FIT		1
-#define CONFIG_FIT_VERBOSE	1
 #define CONFIG_INTEGRITY			/* support booting INTEGRITY OS */
 
 /*
@@ -569,7 +527,7 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy);
 	"osfile=/home/user/board.uImage\0"				\
 	"fdtfile=/home/user/board.dtb\0"				\
 	"ubootfile=/home/user/u-boot.bin\0"				\
-	"fdtaddr=c00000\0"						\
+	"fdtaddr=0x1e00000\0"						\
 	"osaddr=0x1000000\0"						\
 	"loadaddr=0x1000000\0"						\
 	"prog_uboot1="CONFIG_PROG_UBOOT1"\0"				\