X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2Fxpedite520x.h;h=c9bd369029dd11e6e62656bc3c3c5c9187518433;hb=702de89cc6a34c1c23dd3d987b0472b2cecdb63c;hp=7f6927bcb891a305f0be2e5ffa62d1cdced43f41;hpb=6b29a395b62965eef6b5065d3a526a8588a92038;p=platform%2Fkernel%2Fu-boot.git

diff --git a/include/configs/xpedite520x.h b/include/configs/xpedite520x.h
index 7f6927b..c9bd369 100644
--- a/include/configs/xpedite520x.h
+++ b/include/configs/xpedite520x.h
@@ -1,8 +1,7 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
 /*
  * Copyright 2008 Extreme Engineering Solutions, Inc.
  * Copyright 2004-2008 Freescale Semiconductor, Inc.
- *
- * SPDX-License-Identifier:	GPL-2.0+
  */
 
 /*
@@ -14,34 +13,22 @@
 /*
  * High Level Configuration Options
  */
-#define CONFIG_BOOKE		1	/* BOOKE */
-#define CONFIG_E500		1	/* BOOKE e500 family */
-#define CONFIG_XPEDITE5200	1
 #define CONFIG_SYS_BOARD_NAME	"XPedite5200"
 #define CONFIG_SYS_FORM_PMC_XMC	1
-#define CONFIG_BOARD_EARLY_INIT_R	/* Call board_pre_init */
-
-#ifndef CONFIG_SYS_TEXT_BASE
-#define CONFIG_SYS_TEXT_BASE	0xfff80000
-#endif
 
 #define CONFIG_PCI_SCAN_SHOW	1	/* show pci devices on startup */
 #define CONFIG_PCI1		1	/* PCI controller 1 */
 #define CONFIG_FSL_PCI_INIT	1	/* Use common FSL init code */
 #define CONFIG_PCI_INDIRECT_BRIDGE 1	/* indirect PCI bridge support */
 #define CONFIG_SYS_PCI_64BIT	1	/* enable 64-bit PCI resources */
-#define CONFIG_FSL_LAW		1	/* Use common FSL init code */
 
 /*
  * DDR config
  */
-#define CONFIG_SYS_FSL_DDR2
-#undef CONFIG_FSL_DDR_INTERACTIVE
 #define CONFIG_SPD_EEPROM		/* Use SPD EEPROM for DDR setup */
 #define CONFIG_DDR_SPD
 #define CONFIG_MEM_INIT_VALUE		0xdeadbeef
 #define SPD_EEPROM_ADDRESS		0x54
-#define CONFIG_NUM_DDR_CONTROLLERS	1
 #define CONFIG_DIMM_SLOTS_PER_CTLR	1
 #define CONFIG_CHIP_SELECTS_PER_CTRL	2
 #define CONFIG_DDR_ECC
@@ -65,9 +52,6 @@
 /*
  * Diagnostics
  */
-#define CONFIG_SYS_ALT_MEMTEST
-#define CONFIG_SYS_MEMTEST_START	0x10000000
-#define CONFIG_SYS_MEMTEST_END		0x20000000
 #define CONFIG_POST			(CONFIG_SYS_POST_MEMORY | \
 					 CONFIG_SYS_POST_I2C)
 #define I2C_ADDR_LIST			{CONFIG_SYS_I2C_MAX1237_ADDR,	\
@@ -112,9 +96,6 @@
 #define CONFIG_SYS_MAX_FLASH_SECT	1024		/* sectors per device */
 #define CONFIG_SYS_FLASH_ERASE_TOUT	60000		/* Flash Erase Timeout (ms) */
 #define CONFIG_SYS_FLASH_WRITE_TOUT	500		/* Flash Write Timeout (ms) */
-#define CONFIG_FLASH_CFI_DRIVER
-#define CONFIG_SYS_FLASH_CFI
-#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
 #define CONFIG_SYS_FLASH_AUTOPROTECT_LIST	{ {0xfff40000, 0xc0000}, \
 						  {0xfbf40000, 0xc0000} }
 #define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE	/* start of monitor */
@@ -172,7 +153,6 @@
 /*
  * Serial Port
  */
-#define CONFIG_CONS_INDEX		1
 #define CONFIG_SYS_NS16550_SERIAL
 #define CONFIG_SYS_NS16550_REG_SIZE	1
 #define CONFIG_SYS_NS16550_CLK		get_bus_freq(0)
@@ -180,7 +160,6 @@
 #define CONFIG_SYS_NS16550_COM2	(CONFIG_SYS_CCSRBAR+0x4600)
 #define CONFIG_SYS_BAUDRATE_TABLE	\
 	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
-#define CONFIG_BAUDRATE			115200
 #define CONFIG_LOADS_ECHO		1	/* echo on for serial download */
 #define CONFIG_SYS_LOADS_BAUD_CHANGE	1	/* allow baudrate change */
 
@@ -250,9 +229,6 @@
 /*
  * Networking options
  */
-#define CONFIG_TSEC_ENET		/* tsec ethernet support */
-#define CONFIG_PHY_GIGE		1	/* Include GbE speed/duplex detection */
-#define CONFIG_MII		1	/* MII PHY management */
 #define CONFIG_ETHPRIME		"eTSEC1"
 
 #define CONFIG_TSEC1		1
@@ -287,36 +263,12 @@
  * BOOTP options
  */
 #define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-
-/*
- * Command configuration.
- */
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_JFFS2
-#define CONFIG_CMD_NAND
-#define CONFIG_CMD_PCA953X
-#define CONFIG_CMD_PCA953X_INFO
-#define CONFIG_CMD_PCI
-#define CONFIG_CMD_PCI_ENUM
-#define CONFIG_CMD_REGINFO
 
 /*
  * Miscellaneous configurable options
  */
-#define CONFIG_SYS_LONGHELP			/* undef to save memory	*/
 #define CONFIG_SYS_LOAD_ADDR	0x2000000	/* default load address */
-#define CONFIG_SYS_CBSIZE	256		/* Console I/O Buffer Size */
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS	16		/* max number of command args */
-#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size */
-#define CONFIG_CMDLINE_EDITING	1		/* add command line history	*/
-#define CONFIG_AUTO_COMPLETE	1		/* add autocompletion support */
 #define CONFIG_LOADADDR		0x1000000	/* default location for tftp and bootm */
-#define CONFIG_PANIC_HANG			/* do not reset board on panic */
-#define CONFIG_PREBOOT				/* enable preboot variable */
 #define CONFIG_INTEGRITY			/* support booting INTEGRITY OS */
 #define CONFIG_INTERRUPTS		/* enable pci, srio, ddr interrupts */
 
@@ -331,10 +283,6 @@
 /*
  * Environment Configuration
  */
-#define CONFIG_ENV_IS_IN_FLASH	1
-#define CONFIG_ENV_SECT_SIZE	0x20000		/* 128k (one sector) for env */
-#define CONFIG_ENV_SIZE		0x8000
-#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE - (256 * 1024))
 
 /*
  * Flash memory map: