X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2Fvirtlab2.h;h=4bb96cc1ab830025a1ae4f6a26ed19a9fd77dffc;hb=d193c1b6eb05041c94ad9aacd8c94189d1dbc5f8;hp=38b0a4e94355a58efeb162d291ebf12d6f8941df;hpb=50bd0057ba8fceeb48533f8b1a652ccd0e170838;p=platform%2Fkernel%2Fu-boot.git

diff --git a/include/configs/virtlab2.h b/include/configs/virtlab2.h
index 38b0a4e..4bb96cc 100644
--- a/include/configs/virtlab2.h
+++ b/include/configs/virtlab2.h
@@ -37,9 +37,11 @@
 #define CONFIG_VIRTLAB2		1	/* ...on a virtlab2 module	*/
 #define	CONFIG_TQM8xxL		1
 
+#define	CONFIG_SYS_TEXT_BASE	0x40000000
+
 #define	CONFIG_8xx_CONS_SMC1	1	/* Console is on SMC1		*/
-#undef	CONFIG_8xx_CONS_SMC2
-#undef	CONFIG_8xx_CONS_NONE
+#define CONFIG_SYS_SMC_RXBUFLEN	128
+#define CONFIG_SYS_MAXIDLE	10
 #define CONFIG_BAUDRATE		115200	/* console baudrate = 115kbps	*/
 
 #define	CONFIG_BOOTCOUNT_LIMIT
@@ -117,6 +119,7 @@
 #define CONFIG_CMD_ASKENV
 #define CONFIG_CMD_DATE
 #define CONFIG_CMD_DHCP
+#define CONFIG_CMD_EXT2
 #define CONFIG_CMD_IDE
 #define CONFIG_CMD_JFFS2
 #define CONFIG_CMD_NFS
@@ -137,9 +140,6 @@
 
 #define CONFIG_CMDLINE_EDITING	1	/* add command line history	*/
 #define	CONFIG_SYS_HUSH_PARSER		1	/* use "hush" command parser	*/
-#ifdef	CONFIG_SYS_HUSH_PARSER
-#define	CONFIG_SYS_PROMPT_HUSH_PS2	"> "
-#endif
 
 #if defined(CONFIG_CMD_KGDB)
 #define	CONFIG_SYS_CBSIZE		1024	/* Console I/O Buffer Size	*/
@@ -157,8 +157,6 @@
 
 #define	CONFIG_SYS_HZ			1000	/* decrementer freq: 1 ms ticks	*/
 
-#define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }
-
 /*
  * Low Level Configuration Settings
  * (address mappings, register initial values, etc.)
@@ -173,9 +171,8 @@
  * Definitions for initial stack pointer and data area (in DPRAM)
  */
 #define CONFIG_SYS_INIT_RAM_ADDR	CONFIG_SYS_IMMR
-#define	CONFIG_SYS_INIT_RAM_END	0x2F00	/* End of used area in DPRAM	*/
-#define	CONFIG_SYS_GBL_DATA_SIZE	64  /* size in bytes reserved for initial data */
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define	CONFIG_SYS_INIT_RAM_SIZE	0x2F00	/* Size of used area in DPRAM	*/
+#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 #define	CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
 
 /*-----------------------------------------------------------------------
@@ -224,7 +221,9 @@
 /*-----------------------------------------------------------------------
  * Dynamic MTD partition support
  */
-#define CONFIG_JFFS2_CMDLINE
+#define CONFIG_CMD_MTDPARTS
+#define CONFIG_MTD_DEVICE		/* needed for mtdparts commands */
+#define CONFIG_FLASH_CFI_MTD
 #define MTDIDS_DEFAULT		"nor0=TQM8xxL-0"
 
 #define MTDPARTS_DEFAULT	"mtdparts=TQM8xxL-0:256k(u-boot),"	\
@@ -472,15 +471,6 @@
 			 MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 |	\
 			 MAMR_RLFA_1X	 | MAMR_WLFA_1X	   | MAMR_TLFA_4X)
 
-
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define	BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH	*/
-#define BOOTFLAG_WARM	0x02		/* Software reboot			*/
-
 /* Map peripheral control registers on CS4 */
 #define CONFIG_SYS_PERIPHERAL_BASE 0xA0000000
 #define CONFIG_SYS_PERIPHERAL_OR_AM 0xFFFF8000 /* 32 kB address mask */
@@ -488,4 +478,10 @@
 						OR_SCY_2_CLK)
 #define CONFIG_SYS_BR4_PRELIM ((CONFIG_SYS_PERIPHERAL_BASE & BR_BA_MSK) | BR_PS_8 | BR_V)
 #define PCMCIA_CTRL (CONFIG_SYS_PERIPHERAL_BASE + 0xB00)
+
+/* pass open firmware flat tree */
+#define CONFIG_OF_LIBFDT	1
+#define CONFIG_OF_BOARD_SETUP	1
+#define CONFIG_HWCONFIG		1
+
 #endif	/* __CONFIG_H */