X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2Fverdin-imx8mm.h;h=5b5fce9bda177d72e66f9b1fbcca4a4a1f235fe9;hb=46b5c8ed017958fc387ab86c71ae6c90abb6793c;hp=17583c0a6af623f3335bfc05d41591e5f8690616;hpb=111a8b57354bb5aff55635502a0cdf74cb63e835;p=platform%2Fkernel%2Fu-boot.git

diff --git a/include/configs/verdin-imx8mm.h b/include/configs/verdin-imx8mm.h
index 17583c0..5b5fce9 100644
--- a/include/configs/verdin-imx8mm.h
+++ b/include/configs/verdin-imx8mm.h
@@ -9,24 +9,14 @@
 #include <asm/arch/imx-regs.h>
 #include <linux/sizes.h>
 
-#define CONFIG_SPL_MAX_SIZE		(148 * 1024)
 #define CONFIG_SYS_MONITOR_LEN		SZ_512K
 #define CONFIG_SYS_UBOOT_BASE	\
 	(QSPI0_AMBA_BASE + CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR * 512)
 
-#define CONFIG_SYS_BOOTM_LEN           SZ_64M
-
 #ifdef CONFIG_SPL_BUILD
-#define CONFIG_SPL_STACK		0x920000
-#define CONFIG_SPL_BSS_START_ADDR	0x910000
-#define CONFIG_SPL_BSS_MAX_SIZE		SZ_8K	/* 8 KB */
-#define CONFIG_SYS_SPL_MALLOC_START	0x42200000
-#define CONFIG_SYS_SPL_MALLOC_SIZE	SZ_512K	/* 512 KB */
-
 /* malloc f used before GD_FLG_FULL_MALLOC_INIT set */
 #define CONFIG_MALLOC_F_ADDR		0x930000
 /* For RAW image gives a error info not panic */
-#define CONFIG_SPL_ABORT_ON_RAW_IMAGE
 #endif
 
 #define MEM_LAYOUT_ENV_SETTINGS \
@@ -36,16 +26,11 @@
 	"scriptaddr=0x46000000\0"
 
 /* Enable Distro Boot */
-#ifndef CONFIG_SPL_BUILD
 #define BOOT_TARGET_DEVICES(func) \
 	func(MMC, mmc, 1) \
 	func(MMC, mmc, 0) \
 	func(DHCP, dhcp, na)
 #include <config_distro_bootcmd.h>
-#undef CONFIG_ISO_PARTITION
-#else
-#define BOOTENV
-#endif
 
 /* Initial environment variables */
 #define CONFIG_EXTRA_ENV_SETTINGS \
@@ -53,19 +38,14 @@
 	MEM_LAYOUT_ENV_SETTINGS \
 	"bootcmd_mfg=fastboot 0\0" \
 	"boot_file=Image\0" \
+	"boot_script_dhcp=boot.scr\0" \
 	"console=ttymxc0\0" \
 	"fdt_addr=0x43000000\0" \
 	"fdt_board=dev\0" \
 	"initrd_addr=0x43800000\0" \
 	"initrd_high=0xffffffffffffffff\0" \
-	"netargs=setenv bootargs console=${console},${baudrate} " \
-		"root=/dev/nfs ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp" \
-		"\0" \
-	"nfsboot=run netargs; dhcp ${loadaddr} ${boot_file}; " \
-		"tftp ${fdt_addr} verdin/${fdtfile}; " \
-		"booti ${loadaddr} - ${fdt_addr}\0" \
-	"setup=setenv setupargs console=${console},${baudrate} " \
-		"console=tty1 consoleblank=0 earlycon\0" \
+	"setup=setenv setupargs console=tty1 console=${console},${baudrate} " \
+		"consoleblank=0 earlycon\0" \
 	"update_uboot=askenv confirm Did you load flash.bin (y/N)?; " \
 		"if test \"$confirm\" = \"y\"; then " \
 		"setexpr blkcnt ${filesize} + 0x1ff && setexpr blkcnt " \
@@ -74,10 +54,6 @@
 
 #define CONFIG_SYS_INIT_RAM_ADDR        0x40000000
 #define CONFIG_SYS_INIT_RAM_SIZE        SZ_2M
-#define CONFIG_SYS_INIT_SP_OFFSET \
-	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_ADDR \
-	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
 
 #if defined(CONFIG_ENV_IS_IN_MMC)
 /* Environment in eMMC, before config block at the end of 1st "boot sector" */
@@ -89,29 +65,10 @@
 #define PHYS_SDRAM                      0x40000000
 #define PHYS_SDRAM_SIZE			SZ_2G /* 2GB DDR */
 
-/* UART */
-#define CONFIG_MXC_UART_BASE		UART1_BASE_ADDR
-
-/* Monitor Command Prompt */
-#define CONFIG_SYS_CBSIZE		SZ_2K
-#define CONFIG_SYS_MAXARGS		64
-#define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE
-#define CONFIG_SYS_PBSIZE		(CONFIG_SYS_CBSIZE + \
-					sizeof(CONFIG_SYS_PROMPT) + 16)
-/* USDHC */
-#define CONFIG_SYS_FSL_USDHC_NUM	2
-#define CONFIG_SYS_FSL_ESDHC_ADDR	0
-
 /* ENET */
-#define CONFIG_ETHPRIME                 "FEC"
-#define CONFIG_FEC_XCV_TYPE             RGMII
 #define CONFIG_FEC_MXC_PHYADDR          7
-#define FEC_QUIRK_ENET_MAC
-#define IMX_FEC_BASE			0x30BE0000
 
 /* USB Configs */
-#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
 #define CONFIG_MXC_USB_PORTSC	(PORT_PTS_UTMI | PORT_PTS_PTW)
-#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
 
 #endif /* __VERDIN_IMX8MM_H */