X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2Fuc101.h;h=dc1d7e1b3d421813c3cc7205a8cbb99db108ebb6;hb=32bf3d143a888f8deacfdcc97e898f6c06d0aea4;hp=8cd8e9be709ae9e7298e00bcef9afc2eb4c6577e;hpb=6dedf3d49dd14c3bf541c8ecee7ffaac5f0e1d6c;p=platform%2Fkernel%2Fu-boot.git

diff --git a/include/configs/uc101.h b/include/configs/uc101.h
index 8cd8e9b..dc1d7e1 100644
--- a/include/configs/uc101.h
+++ b/include/configs/uc101.h
@@ -38,11 +38,6 @@
 #define BOOTFLAG_COLD		0x01	/* Normal Power-On: Boot from FLASH	*/
 #define BOOTFLAG_WARM		0x02	/* Software reboot			*/
 
-#define CFG_CACHELINE_SIZE	32	/* For MPC5xxx CPUs			*/
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#  define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value	*/
-#endif
-
 #define CONFIG_BOARD_EARLY_INIT_R
 
 /*
@@ -55,25 +50,34 @@
 /* Partitions */
 #define CONFIG_DOS_PARTITION
 
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+
 /*
- * Supported commands
+ * Command line configuration.
  */
-#define CONFIG_COMMANDS	       (CONFIG_CMD_DFL	| \
-				CFG_CMD_DATE	| \
-				CFG_CMD_DISPLAY	| \
-				CFG_CMD_DHCP	| \
-				CFG_CMD_PING	| \
-				CFG_CMD_EEPROM	| \
-				CFG_CMD_I2C	| \
-				CFG_CMD_DTT	| \
-				CFG_CMD_IDE	| \
-				CFG_CMD_FAT	| \
-				CFG_CMD_NFS	| \
-				CFG_CMD_MII	| \
-				CFG_CMD_SNTP	)
-
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_DATE
+#define CONFIG_CMD_DISPLAY
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_EEPROM
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_DTT
+#define CONFIG_CMD_IDE
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_NFS
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_SNTP
+
 
 #define	CONFIG_TIMESTAMP	1	/* Print image info with timestamp */
 
@@ -87,7 +91,7 @@
 #define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds */
 
 #define CONFIG_PREBOOT	"echo;" \
-	"echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
+	"echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
 	"echo"
 
 #undef	CONFIG_BOOTARGS
@@ -114,7 +118,7 @@
 /*
  * IPB Bus clocking configuration.
  */
-#define CFG_IPBSPEED_133		/* define for 133MHz speed */
+#define CFG_IPBCLK_EQUALS_XLBCLK		/* define for 133MHz speed */
 
 /*
  * I2C configuration
@@ -245,7 +249,7 @@
  */
 #define CFG_LONGHELP			/* undef to save memory	    */
 #define CFG_PROMPT		"=> "	/* Monitor Command Prompt   */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
 #define CFG_CBSIZE		1024	/* Console I/O Buffer Size  */
 #else
 #define CFG_CBSIZE		256	/* Console I/O Buffer Size  */
@@ -264,9 +268,13 @@
 
 #define CFG_HZ			1000	/* decrementer freq: 1 ms ticks */
 
+#define CFG_CACHELINE_SIZE	32	/* For MPC5xxx CPUs			*/
+#if defined(CONFIG_CMD_KGDB)
+#  define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value	*/
+#endif
+
 /*
- * Enable loopw commando. This has only affect, if CFG_CMD_MEM is defined,
- * which is normally part of the default commands (CFV_CMD_DFL)
+ * Enable loopw command.
  */
 #define CONFIG_LOOPW
 
@@ -289,7 +297,7 @@
 
 /* 8Mbit SRAM @0x80100000 */
 #define CFG_CS1_START		CFG_SRAM_BASE
-#define CFG_CS1_SIZE		0x00100000
+#define CFG_CS1_SIZE		0x00200000
 #define CFG_CS1_CFG		0x21D00
 
 /* Display H1, Status Inputs, EPLD @0x80600000 8 Bit */
@@ -324,7 +332,6 @@
 #define CFG_IDE_MAXDEVICE	2	/* max. 2 drives per IDE bus	*/
 
 #define CONFIG_IDE_PREINIT	1
-/* #define CONFIG_IDE_RESET	1 beispile siehe tqm5200.c */
 
 #define CFG_ATA_IDE0_OFFSET	0x0000