X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2Ftricorder.h;h=1d58701d98c302ba8c02dc5f19295537335796ef;hb=d56b4b19744c314c26dc77585a7c7a9253d1487d;hp=1c36d0751c4c5282a4a21fa8333b7ae38babf9d9;hpb=c27269953b94d19b3fc7a21a1c3e19985507b94d;p=platform%2Fkernel%2Fu-boot.git

diff --git a/include/configs/tricorder.h b/include/configs/tricorder.h
index 1c36d07..1d58701 100644
--- a/include/configs/tricorder.h
+++ b/include/configs/tricorder.h
@@ -16,14 +16,6 @@
 #ifndef __CONFIG_H
 #define __CONFIG_H
 
-/* High Level Configuration Options */
-#define CONFIG_SYS_THUMB_BUILD
-#define CONFIG_OMAP			/* in a TI OMAP core */
-/* Common ARM Erratas */
-#define CONFIG_ARM_ERRATA_454179
-#define CONFIG_ARM_ERRATA_430973
-#define CONFIG_ARM_ERRATA_621766
-
 #define CONFIG_MACH_TYPE		MACH_TYPE_TRICORDER
 /*
  * 1MB into the SDRAM to allow for SPL's bss at the beginning of SDRAM
@@ -54,26 +46,6 @@
 
 /* Hardware drivers */
 
-/* GPIO support */
-#define CONFIG_OMAP_GPIO
-
-/* GPIO banks */
-#define CONFIG_OMAP3_GPIO_2		/* GPIO32..63 are in GPIO bank 2 */
-
-/* LED support */
-#define CONFIG_STATUS_LED
-#define CONFIG_BOARD_SPECIFIC_LED
-#define CONFIG_CMD_LED			/* LED command */
-#define STATUS_LED_BIT			(1 << 0)
-#define STATUS_LED_STATE		STATUS_LED_ON
-#define STATUS_LED_PERIOD		(CONFIG_SYS_HZ / 2)
-#define STATUS_LED_BIT1			(1 << 1)
-#define STATUS_LED_STATE1		STATUS_LED_ON
-#define STATUS_LED_PERIOD1		(CONFIG_SYS_HZ / 2)
-#define STATUS_LED_BIT2			(1 << 2)
-#define STATUS_LED_STATE2		STATUS_LED_ON
-#define STATUS_LED_PERIOD2		(CONFIG_SYS_HZ / 2)
-
 /* NS16550 Configuration */
 #define CONFIG_SYS_NS16550_SERIAL
 #define CONFIG_SYS_NS16550_REG_SIZE	(-4)
@@ -83,15 +55,9 @@
 #define CONFIG_CONS_INDEX		3
 #define CONFIG_SYS_NS16550_COM3		OMAP34XX_UART3
 #define CONFIG_SERIAL3			3
-#define CONFIG_BAUDRATE			115200
 #define CONFIG_SYS_BAUDRATE_TABLE	{4800, 9600, 19200, 38400, 57600,\
 					115200}
 
-/* MMC */
-#define CONFIG_GENERIC_MMC
-#define CONFIG_OMAP_HSMMC
-#define CONFIG_DOS_PARTITION
-
 /* I2C */
 #define CONFIG_SYS_I2C
 #define CONFIG_SYS_OMAP24_I2C_SPEED	100000
@@ -100,16 +66,13 @@
  
 
 /* EEPROM */
-#define CONFIG_CMD_EEPROM
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN	2
 #define CONFIG_SYS_EEPROM_BUS_NUM	1
 
 /* TWL4030 */
-#define CONFIG_TWL4030_POWER
 #define CONFIG_TWL4030_LED
 
 /* Board NAND Info */
-#define CONFIG_SYS_NO_FLASH		/* no NOR flash */
 #define CONFIG_MTD_DEVICE		/* needed for mtdparts commands */
 #define MTDIDS_DEFAULT			"nand0=omap2-nand.0"
 #define MTDPARTS_DEFAULT		"mtdparts=omap2-nand.0:" \
@@ -135,16 +98,10 @@
 #define CONFIG_SYS_NAND_MAX_ECCPOS	56
 
 /* commands to include */
-#define CONFIG_CMD_MTDPARTS		/* Enable MTD parts commands */
 #define CONFIG_CMD_NAND			/* NAND support */
 #define CONFIG_CMD_NAND_LOCK_UNLOCK	/* nand (un)lock commands */
-#define CONFIG_CMD_UBIFS		/* UBIFS commands */
-#define CONFIG_LZO			/* LZO is needed for UBIFS */
-
-#undef CONFIG_CMD_JFFS2			/* JFFS2 Support */
 
 /* needed for ubi */
-#define CONFIG_RBTREE
 #define CONFIG_MTD_DEVICE       /* needed for mtdparts commands */
 #define CONFIG_MTD_PARTITIONS
 
@@ -309,7 +266,6 @@
 #define CONFIG_SPL_FRAMEWORK
 #define CONFIG_SPL_NAND_SIMPLE
 
-#define CONFIG_SPL_BOARD_INIT
 #define CONFIG_SPL_NAND_BASE
 #define CONFIG_SPL_NAND_DRIVERS
 #define CONFIG_SPL_NAND_ECC