X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2Fti_armv7_common.h;h=828fb1b2a59cd69fe284e9836e85618454159d99;hb=bdf97b5d393fc94666a847e9bac1c358b2c63c59;hp=4771e749405b5c99cccf4734a91c4b7f88d4ae3e;hpb=e12546de54fc9be818e8d39967b07fa351d9e5ba;p=platform%2Fkernel%2Fu-boot.git

diff --git a/include/configs/ti_armv7_common.h b/include/configs/ti_armv7_common.h
index 4771e74..828fb1b 100644
--- a/include/configs/ti_armv7_common.h
+++ b/include/configs/ti_armv7_common.h
@@ -1,10 +1,9 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
 /*
  * ti_armv7_common.h
  *
  * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com/
  *
- * SPDX-License-Identifier:	GPL-2.0+
- *
  * The various ARMv7 SoCs from TI all share a number of IP blocks when
  * implementing a given feature.  Rather than define these in every
  * board or even SoC common file, we define a common file to be re-used
@@ -53,7 +52,7 @@
 
 #define DEFAULT_FIT_TI_ARGS \
 	"boot_fit=0\0" \
-	"fit_loadaddr=0x87000000\0" \
+	"fit_loadaddr=0x90000000\0" \
 	"fit_bootfile=fitImage\0" \
 	"update_to_fit=setenv loadaddr ${fit_loadaddr}; setenv bootfile ${fit_bootfile}\0" \
 	"loadfit=run args_mmc; bootm ${loadaddr}#${fdtfile};\0" \
@@ -65,9 +64,6 @@
  * initial stack pointer in our SRAM. Otherwise, we can define
  * CONFIG_NR_DRAM_BANKS before including this file.
  */
-#ifndef CONFIG_NR_DRAM_BANKS
-#define CONFIG_NR_DRAM_BANKS		1
-#endif
 #define CONFIG_SYS_SDRAM_BASE		0x80000000
 
 #ifndef CONFIG_SYS_INIT_SP_ADDR
@@ -78,31 +74,12 @@
 /* Timer information. */
 #define CONFIG_SYS_PTV			2	/* Divisor: 2^(PTV+1) => 8 */
 
-/*
- * Disable DM_* for SPL build and can be re-enabled after adding
- * DM support in SPL
- */
-#ifdef CONFIG_SPL_BUILD
-#undef CONFIG_DM_I2C
-#endif
-
-/* I2C IP block */
+/* If DM_I2C, enable non-DM I2C support */
+#if !defined(CONFIG_DM_I2C)
 #define CONFIG_I2C
-#ifndef CONFIG_DM_I2C
 #define CONFIG_SYS_I2C
-#else
-/*
- * Enable CONFIG_DM_I2C_COMPAT temporarily until all the i2c client
- * devices are adopted to DM
- */
-#define CONFIG_DM_I2C_COMPAT
 #endif
 
-/* McSPI IP block */
-#define CONFIG_SPI
-
-/* GPIO block */
-
 /*
  * The following are general good-enough settings for U-Boot.  We set a
  * large malloc pool as we generally have a lot of DDR, and we opt for
@@ -130,9 +107,6 @@
  * mtdparts, both for ease of use in U-Boot and for passing information
  * on to the Linux kernel.
  */
-#if defined(CONFIG_SPI_BOOT) || defined(CONFIG_NOR) || defined(CONFIG_NAND) || defined(CONFIG_NAND_DAVINCI)
-#define CONFIG_MTD_DEVICE		/* Required for mtdparts */
-#endif
 
 /*
  * Our platforms make use of SPL to initalize the hardware (primarily
@@ -177,7 +151,9 @@
 
 /* FAT sd card locations. */
 #define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION	1
+#ifndef CONFIG_SPL_FS_LOAD_PAYLOAD_NAME
 #define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME	"u-boot.img"
+#endif
 
 #ifdef CONFIG_SPL_OS_BOOT
 /* FAT */