X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2Ftaishan.h;h=12f35ae1f4a71e8313207415111284d36f267e9a;hb=37a3bda0c9c8a2ffbf7e2a9e121177a3385a0626;hp=ab3b0c1acba3017e7e45c2a967b297fab769040f;hpb=9caeaadf508cd0e11ac5dfc56ab0f72e3b89a105;p=platform%2Fkernel%2Fu-boot.git diff --git a/include/configs/taishan.h b/include/configs/taishan.h index ab3b0c1..12f35ae 100644 --- a/include/configs/taishan.h +++ b/include/configs/taishan.h @@ -32,9 +32,17 @@ #define CONFIG_440GX 1 /* Specifc GX support */ #define CONFIG_440 1 /* ... PPC440 family */ #define CONFIG_4xx 1 /* ... PPC4xx family */ -#undef CFG_DRAM_TEST /* Disable-takes long time! */ #define CONFIG_SYS_CLK_FREQ 33333333 /* external freq to pll */ +#define CONFIG_SYS_TEXT_BASE 0xFFFC0000 + +/* + * Include common defines/options for all AMCC eval boards + */ +#define CONFIG_HOSTNAME taishan +#define CONFIG_USE_TTY ttyS1 +#include "amcc-common.h" + #define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */ #define CONFIG_MISC_INIT_R 1 /* Call misc_init_r */ @@ -42,76 +50,64 @@ * Base addresses -- Note these are effective addresses where the * actual resources get mapped (not physical addresses) *----------------------------------------------------------------------*/ -#define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */ -#define CFG_FLASH_BASE 0xfc000000 /* start of FLASH */ -#define CFG_MONITOR_BASE 0xfffc0000 /* start of monitor */ -#define CFG_PCI_MEMBASE 0x80000000 /* mapped pci memory */ -#define CFG_PERIPHERAL_BASE 0xe0000000 /* internal peripherals */ -#define CFG_ISRAM_BASE 0xc0000000 /* internal SRAM */ -#define CFG_PCI_BASE 0xd0000000 /* internal PCI regs */ +#define CONFIG_SYS_FLASH_BASE 0xfc000000 /* start of FLASH */ +#define CONFIG_SYS_PCI_MEMBASE 0x80000000 /* mapped pci memory */ +#define CONFIG_SYS_ISRAM_BASE 0xc0000000 /* internal SRAM */ +#define CONFIG_SYS_PCI_BASE 0xd0000000 /* internal PCI regs */ -#define CFG_EBC0_FLASH_BASE CFG_FLASH_BASE -#define CFG_EBC1_FPGA_BASE (CFG_PERIPHERAL_BASE + 0x01000000) -#define CFG_EBC2_LCM_BASE (CFG_PERIPHERAL_BASE + 0x02000000) -#define CFG_EBC3_CONN_BASE (CFG_PERIPHERAL_BASE + 0x08000000) +#define CONFIG_SYS_EBC0_FLASH_BASE CONFIG_SYS_FLASH_BASE +#define CONFIG_SYS_EBC1_FPGA_BASE (CONFIG_SYS_PERIPHERAL_BASE + 0x01000000) +#define CONFIG_SYS_EBC2_LCM_BASE (CONFIG_SYS_PERIPHERAL_BASE + 0x02000000) +#define CONFIG_SYS_EBC3_CONN_BASE (CONFIG_SYS_PERIPHERAL_BASE + 0x08000000) -#define CFG_GPIO_BASE (CFG_PERIPHERAL_BASE + 0x00000700) +#define CONFIG_SYS_GPIO_BASE (CONFIG_SYS_PERIPHERAL_BASE + 0x00000700) /*----------------------------------------------------------------------- * Initial RAM & stack pointer (placed in internal SRAM) *----------------------------------------------------------------------*/ -#define CFG_TEMP_STACK_OCM 1 -#define CFG_OCM_DATA_ADDR CFG_ISRAM_BASE -#define CFG_INIT_RAM_ADDR CFG_ISRAM_BASE /* Initial RAM address */ -#define CFG_INIT_RAM_END 0x2000 /* End of used area in RAM*/ -#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data*/ - -#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) -#define CFG_POST_WORD_ADDR (CFG_GBL_DATA_OFFSET - 0x4) -#define CFG_INIT_SP_OFFSET CFG_POST_WORD_ADDR +#define CONFIG_SYS_TEMP_STACK_OCM 1 +#define CONFIG_SYS_OCM_DATA_ADDR CONFIG_SYS_ISRAM_BASE +#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_ISRAM_BASE /* Initial RAM address */ +#define CONFIG_SYS_INIT_RAM_END 0x2000 /* End of used area in RAM*/ +#define CONFIG_SYS_GBL_DATA_SIZE 128 /* num bytes initial data*/ -#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon*/ -#define CFG_MALLOC_LEN (1024 * 1024) /* Reserve 1024 kB for malloc*/ +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET (CONFIG_SYS_GBL_DATA_OFFSET - 0x4) /*----------------------------------------------------------------------- * Serial Port *----------------------------------------------------------------------*/ -#define CONFIG_UART1_CONSOLE 1 /* use of UART1 as console */ -#define CONFIG_SERIAL_MULTI 1 /* enable serial multi support */ -#define CFG_EXT_SERIAL_CLOCK (1843200 * 6) /* Ext clk @ 11.059 MHz */ -#define CONFIG_BAUDRATE 115200 - -#define CFG_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} +#define CONFIG_CONS_INDEX 2 /* Use UART1 */ +#define CONFIG_SYS_EXT_SERIAL_CLOCK (1843200 * 6) /* Ext clk @ 11.059 MHz */ /*----------------------------------------------------------------------- * Environment *----------------------------------------------------------------------*/ -#define CFG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */ +#define CONFIG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */ /*----------------------------------------------------------------------- * FLASH related *----------------------------------------------------------------------*/ -#define CFG_FLASH_CFI -#define CFG_FLASH_CFI_DRIVER -#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ -#define CFG_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */ +#define CONFIG_SYS_FLASH_CFI +#define CONFIG_FLASH_CFI_DRIVER +#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ +#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */ -#define CFG_FLASH_BANKS_LIST {CFG_FLASH_BASE} -#define CFG_MAX_FLASH_BANKS 1 /* number of banks */ -#define CFG_MAX_FLASH_SECT 1024 /* sectors per device */ +#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE} +#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ +#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */ -#undef CFG_FLASH_CHECKSUM -#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ -#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ +#undef CONFIG_SYS_FLASH_CHECKSUM +#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ +#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ -#define CFG_ENV_SECT_SIZE 0x40000 /* size of one complete sector */ -#define CFG_ENV_ADDR (CFG_MONITOR_BASE-CFG_ENV_SECT_SIZE) -#define CFG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */ +#define CONFIG_ENV_SECT_SIZE 0x40000 /* size of one complete sector */ +#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE-CONFIG_ENV_SECT_SIZE) +#define CONFIG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */ /* Address and size of Redundant Environment Sector */ -#define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR-CFG_ENV_SECT_SIZE) -#define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE) +#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR-CONFIG_ENV_SECT_SIZE) +#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) /*----------------------------------------------------------------------- * E2PROM bootstrap configure value @@ -132,92 +128,46 @@ *----------------------------------------------------------------------*/ #undef CONFIG_SPD_EEPROM /* Don't use SPD EEPROM for setup */ #define CONFIG_SDRAM_BANK0 1 /* init onboard DDR SDRAM bank 0 */ -#define CFG_SDRAM0_TR0 0xC10A401A +#define CONFIG_SYS_SDRAM0_TR0 0xC10A401A #undef CONFIG_SDRAM_ECC /* enable ECC support */ /*----------------------------------------------------------------------- * I2C *----------------------------------------------------------------------*/ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ -#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CFG_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#undef CFG_I2C_MULTI_EEPROMS -#define CFG_I2C_EEPROM_ADDR 0x50 -#define CFG_I2C_EEPROM_ADDR_LEN 1 -#define CFG_EEPROM_PAGE_WRITE_ENABLE -#define CFG_EEPROM_PAGE_WRITE_BITS 3 -#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 +#undef CONFIG_SYS_I2C_MULTI_EEPROMS +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 -#define CFG_BOOTSTRAP_IIC_ADDR 0x50 +#define CONFIG_SYS_BOOTSTRAP_IIC_ADDR 0x50 /* I2C SYSMON (LM75, AD7414 is almost compatible) */ #define CONFIG_DTT_LM75 1 /* ON Semi's LM75 */ #define CONFIG_DTT_SENSORS {0} /* Sensor addresses */ -#define CFG_DTT_MAX_TEMP 70 -#define CFG_DTT_LOW_TEMP -30 -#define CFG_DTT_HYSTERESIS 3 - -/*----------------------------------------------------------------------- - * Environment - *----------------------------------------------------------------------*/ - -#define CONFIG_PREBOOT "echo;" \ - "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \ - "echo" - -#undef CONFIG_BOOTARGS +#define CONFIG_SYS_DTT_MAX_TEMP 70 +#define CONFIG_SYS_DTT_LOW_TEMP -30 +#define CONFIG_SYS_DTT_HYSTERESIS 3 +/* + * Default environment variables + */ #define CONFIG_EXTRA_ENV_SETTINGS \ - "netdev=eth0\0" \ - "hostname=taishan\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=${serverip}:${rootpath}\0" \ - "ramargs=setenv bootargs root=/dev/ram rw\0" \ - "addip=setenv bootargs ${bootargs} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ - ":${hostname}:${netdev}:off panic=1\0" \ - "addtty=setenv bootargs ${bootargs} console=ttyS1,${baudrate}\0"\ - "flash_nfs=run nfsargs addip addtty;" \ - "bootm ${kernel_addr}\0" \ - "flash_self=run ramargs addip addtty;" \ - "bootm ${kernel_addr} ${ramdisk_addr}\0" \ - "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \ - "bootm\0" \ - "rootpath=/opt/eldk/ppc_4xx\0" \ - "bootfile=/tftpboot/taishan/uImage\0" \ + CONFIG_AMCC_DEF_ENV \ + CONFIG_AMCC_DEF_ENV_POWERPC \ + CONFIG_AMCC_DEF_ENV_PPC_OLD \ + CONFIG_AMCC_DEF_ENV_NOR_UPD \ "kernel_addr=fc000000\0" \ "ramdisk_addr=fc180000\0" \ - "initrd_high=30000000\0" \ - "load=tftp 100000 /tftpboot/taishan/u-boot.bin\0" \ - "update=protect off fffc0000 ffffffff;era fffc0000 ffffffff;" \ - "cp.b 100000 fffc0000 40000;" \ - "setenv filesize;saveenv\0" \ - "upd=run load;run update\0" \ - "fixedip=setenv bootargs $(bootargs) ip=$(ipaddr):$(serverip):" \ - "$(gatewayip):$(netmask):$(hostname):$(netdev):off panic=1\0" \ - "dhcp=setenv bootargs $(bootargs) ip=dhcp\0" \ "kozio=bootm 0xffe00000\0" \ "" -#define CONFIG_BOOTCOMMAND "run flash_self" - -#if 0 -#define CONFIG_BOOTDELAY -1 /* autoboot disabled */ -#else -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ -#endif - -#define CONFIG_BAUDRATE 115200 -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ /*----------------------------------------------------------------------- * Networking *----------------------------------------------------------------------*/ #define CONFIG_EMAC_NR_START 2 /* start with EMAC 2 (skip 0&1) */ -#define CONFIG_MII 1 /* MII PHY management */ -#define CONFIG_NET_MULTI 1 #define CONFIG_PHY_ADDR 0xff /* no phy on EMAC0 */ #define CONFIG_PHY1_ADDR 0xff /* no phy on EMAC1 */ #define CONFIG_PHY2_ADDR 0x1 @@ -230,70 +180,12 @@ #define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */ #define CONFIG_PHY_RESET 1 /* reset phy upon startup */ #define CONFIG_PHY_RESET_DELAY 1000 -#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */ - -#define CONFIG_NETCONSOLE /* include NetConsole support */ - /* - * BOOTP options + * Commands additional to the ones defined in amcc-common.h */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - - -/* - * Command line configuration. - */ -#include - -#define CONFIG_CMD_ASKENV -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_DIAG #define CONFIG_CMD_DTT -#define CONFIG_CMD_ELF -#define CONFIG_CMD_EEPROM -#define CONFIG_CMD_I2C -#define CONFIG_CMD_IRQ -#define CONFIG_CMD_MII -#define CONFIG_CMD_NET -#define CONFIG_CMD_NFS #define CONFIG_CMD_PCI -#define CONFIG_CMD_PING -#define CONFIG_CMD_REGINFO - - -#undef CONFIG_WATCHDOG /* watchdog disabled */ - -/*----------------------------------------------------------------------- - * Miscellaneous configurable options - *----------------------------------------------------------------------*/ -#define CFG_LONGHELP /* undef to save memory */ -#define CFG_PROMPT "=> " /* Monitor Command Prompt */ -#if defined(CONFIG_CMD_KGDB) -#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ - -#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ -#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ - -#define CFG_LOAD_ADDR 0x100000 /* default load address */ -#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */ - -#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ - -#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ -#define CONFIG_LOOPW 1 /* enable loopw command */ -#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */ -#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ -#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ /*----------------------------------------------------------------------- * PCI stuff @@ -304,31 +196,12 @@ #define CONFIG_PCI_PNP /* do pci plug-and-play */ #define CONFIG_EEPRO100 1 /* include PCI EEPRO100 */ #define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ -#define CFG_PCI_TARGBASE 0x80000000 /* PCIaddr mapped to CFG_PCI_MEMBASE */ +#define CONFIG_SYS_PCI_TARGBASE 0x80000000 /* PCIaddr mapped to CONFIG_SYS_PCI_MEMBASE */ /* Board-specific PCI */ -#define CFG_PCI_TARGET_INIT /* let board init pci target */ - -#define CFG_PCI_SUBSYS_VENDORID 0x10e8 /* AMCC */ -#define CFG_PCI_SUBSYS_DEVICEID 0xcafe /* Whatever */ - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ +#define CONFIG_SYS_PCI_TARGET_INIT /* let board init pci target */ -/* - * Internal Definitions - * - * Boot Flags - */ -#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ -#define BOOTFLAG_WARM 0x02 /* Software reboot */ +#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x10e8 /* AMCC */ +#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0xcafe /* Whatever */ -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ -#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ -#endif #endif /* __CONFIG_H */