X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2Fstxgp3.h;h=ec04a30bec99a97ea7ed1d5f3f9ad93ffc4dda59;hb=53677ef18e25c97ac613349087c5cb33ae5a2741;hp=b5684d334b3165ff637a2c7ec04ca7f9771bfb48;hpb=9c4c5ae3e10e4f2ca799aacbb74e1f5adb86e0b5;p=platform%2Fkernel%2Fu-boot.git diff --git a/include/configs/stxgp3.h b/include/configs/stxgp3.h index b5684d3..ec04a30 100644 --- a/include/configs/stxgp3.h +++ b/include/configs/stxgp3.h @@ -42,8 +42,8 @@ #define CONFIG_CPM2 1 /* has CPM2 */ #define CONFIG_STXGP3 1 /* Silicon Tx GPPP board specific*/ -#undef CONFIG_PCI /* pci ethernet support */ -#define CONFIG_TSEC_ENET /* tsec ethernet support*/ +#undef CONFIG_PCI /* pci ethernet support */ +#define CONFIG_TSEC_ENET /* tsec ethernet support*/ #undef CONFIG_ETHER_ON_FCC /* cpm FCC ethernet support */ #define CONFIG_ENV_OVERWRITE #define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */ @@ -51,6 +51,7 @@ #define CONFIG_DDR_DLL /* possible DLL fix needed */ #define CONFIG_DDR_2T_TIMING /* Sets the 2T timing bit */ +#define CONFIG_FSL_LAW 1 /* Use common FSL init code */ /* sysclk for MPC85xx */ @@ -99,7 +100,7 @@ #define CFG_OR1_PRELIM 0xffff0ff7 /* 64K is enough */ #define CFG_LBC_LCLDEVS_BASE 0xfc000000 /* Base of localbus devices */ -#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */ +#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */ #if (CFG_MONITOR_BASE < CFG_FLASH_BASE) #define CFG_RAMBOOT @@ -108,11 +109,12 @@ #endif #ifdef CFG_RAMBOOT -#define CFG_CCSRBAR_DEFAULT 0x40000000 /* CCSRBAR by BDI cfg */ +#define CFG_CCSRBAR_DEFAULT 0x40000000 /* CCSRBAR by BDI cfg */ #else -#define CFG_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */ +#define CFG_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */ #endif #define CFG_CCSRBAR 0xfdf00000 /* relocated CCSRBAR */ +#define CFG_CCSRBAR_PHYS CFG_CCSRBAR /* physical addr of CCSRBAR */ #define CFG_IMMR CFG_CCSRBAR /* PQII uses CFG_IMMR */ @@ -127,14 +129,14 @@ #define CFG_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory */ #define CFG_SDRAM_BASE CFG_DDR_SDRAM_BASE -#define SPD_EEPROM_ADDRESS 0x54 /* DDR DIMM */ +#define SPD_EEPROM_ADDRESS 0x54 /* DDR DIMM */ #undef CONFIG_CLOCKS_IN_MHZ /* local bus definitions */ #define CFG_BR2_PRELIM 0xf8001861 /* 64MB localbus SDRAM */ #define CFG_OR2_PRELIM 0xfc006901 -#define CFG_LBC_LCRR 0x00030004 /* local bus freq */ +#define CFG_LBC_LCRR 0x00030004 /* local bus freq */ #define CFG_LBC_LBCR 0x00000000 #define CFG_LBC_LSRT 0x20000000 #define CFG_LBC_MRTPR 0x20000000 @@ -145,23 +147,23 @@ #define CFG_LBC_LSDMR_5 0x4061b723 #define CONFIG_L1_INIT_RAM -#define CFG_INIT_RAM_LOCK 1 +#define CFG_INIT_RAM_LOCK 1 #define CFG_INIT_RAM_ADDR 0x60000000 /* Initial RAM address */ -#define CFG_INIT_RAM_END 0x4000 /* End of used area in RAM */ +#define CFG_INIT_RAM_END 0x4000 /* End of used area in RAM */ -#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */ +#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */ #define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) #define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET -#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ -#define CFG_MALLOC_LEN (128 * 1024) /* Reserved for malloc */ +#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ +#define CFG_MALLOC_LEN (128 * 1024) /* Reserved for malloc */ /* Serial Port */ -#define CONFIG_CONS_ON_SCC /* define if console on SCC */ -#undef CONFIG_CONS_NONE /* define if console on something else */ -#define CONFIG_CONS_INDEX 2 /* which serial channel for console */ +#define CONFIG_CONS_ON_SCC /* define if console on SCC */ +#undef CONFIG_CONS_NONE /* define if console on something else */ +#define CONFIG_CONS_INDEX 2 /* which serial channel for console */ -#define CONFIG_BAUDRATE 38400 +#define CONFIG_BAUDRATE 38400 #define CFG_BAUDRATE_TABLE \ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200} @@ -172,8 +174,11 @@ #define CFG_PROMPT_HUSH_PS2 "> " #endif -/* I2C */ -#define CONFIG_HARD_I2C /* I2C with hardware support*/ +/* + * I2C + */ +#define CONFIG_FSL_I2C /* Use FSL common I2C driver */ +#define CONFIG_HARD_I2C /* I2C with hardware support*/ #undef CONFIG_SOFT_I2C /* I2C bit-banged */ #define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ #define CFG_I2C_SLAVE 0x7F @@ -183,6 +188,7 @@ /* I did the 'if 0' so we could keep the syntax above if ever needed. */ #undef CFG_I2C_NOPROBES #endif +#define CFG_I2C_OFFSET 0x3000 /* RapdIO Map configuration, mapped 1:1. */ @@ -199,18 +205,18 @@ #define CFG_PCI1_IO_PHYS CFG_PCI1_IO_BASE #define CFG_PCI1_IO_SIZE 0x01000000 /* 16 M */ -#if defined(CONFIG_PCI) /* PCI Ethernet card */ +#if defined(CONFIG_PCI) /* PCI Ethernet card */ #define CONFIG_NET_MULTI -#define CONFIG_PCI_PNP /* do pci plug-and-play */ +#define CONFIG_PCI_PNP /* do pci plug-and-play */ #undef CONFIG_EEPRO100 #undef CONFIG_TULIP #if !defined(CONFIG_PCI_PNP) - #define PCI_ENET0_IOADDR 0xe0000000 + #define PCI_ENET0_IOADDR 0xe0000000 #define PCI_ENET0_MEMADDR 0xe0000000 - #define PCI_IDSEL_NUMBER 0x0c /* slot0->3(IDSEL)=12->15 */ + #define PCI_IDSEL_NUMBER 0x0c /* slot0->3(IDSEL)=12->15 */ #endif #undef CONFIG_PCI_SCAN_SHOW @@ -221,20 +227,23 @@ #if defined(CONFIG_TSEC_ENET) #ifndef CONFIG_NET_MULTI -#define CONFIG_NET_MULTI 1 +#define CONFIG_NET_MULTI 1 #endif #define CONFIG_MII 1 /* MII PHY management */ -#define CONFIG_MPC85XX_TSEC1 1 -#define CONFIG_MPC85XX_TSEC2 1 -#undef CONFIG_MPS85XX_FEC +#define CONFIG_TSEC1 1 +#define CONFIG_TSEC1_NAME "TSEC0" +#define CONFIG_TSEC2 1 +#define CONFIG_TSEC2_NAME "TSEC1" #define TSEC1_PHY_ADDR 2 #define TSEC2_PHY_ADDR 4 #define TSEC1_PHYIDX 0 #define TSEC2_PHYIDX 0 -#define CONFIG_ETHPRIME "MOTO ENET0" +#define TSEC1_FLAGS TSEC_GIGABIT +#define TSEC2_FLAGS TSEC_GIGABIT +#define CONFIG_ETHPRIME "TSEC0" #elif defined(CONFIG_ETHER_ON_FCC) /* CPM FCC Ethernet */ @@ -261,7 +270,7 @@ #elif (CONFIG_ETHER_INDEX == 3) /* need more definitions here for FE3 */ #define FETH3_RST 0x80 -#endif /* CONFIG_ETHER_INDEX */ +#endif /* CONFIG_ETHER_INDEX */ /* MDIO is done through the TSEC0 control. */ @@ -292,34 +301,38 @@ #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ #define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ +/* + * BOOTP options + */ +#define CONFIG_BOOTP_BOOTFILESIZE +#define CONFIG_BOOTP_BOOTPATH +#define CONFIG_BOOTP_GATEWAY +#define CONFIG_BOOTP_HOSTNAME + + +/* + * Command line configuration. + */ +#include + +#define CONFIG_CMD_PING +#define CONFIG_CMD_I2C + #if defined(CFG_RAMBOOT) - #if defined(CONFIG_PCI) - #define CONFIG_COMMANDS ((CONFIG_CMD_DFL | CFG_CMD_PCI | \ - CFG_CMD_PING | CFG_CMD_I2C) & \ - ~(CFG_CMD_ENV | \ - CFG_CMD_LOADS )) - #elif defined(CONFIG_TSEC_ENET) - #define CONFIG_COMMANDS ((CONFIG_CMD_DFL | CFG_CMD_PING | \ - CFG_CMD_MII | CFG_CMD_I2C ) & \ - ~(CFG_CMD_ENV)) - #elif defined(CONFIG_ETHER_ON_FCC) - #define CONFIG_COMMANDS ((CONFIG_CMD_DFL | CFG_CMD_MII | \ - CFG_CMD_PING | CFG_CMD_I2C) & \ - ~(CFG_CMD_ENV)) - #endif + #undef CONFIG_CMD_ENV + #undef CONFIG_CMD_LOADS #else - #if defined(CONFIG_PCI) - #define CONFIG_COMMANDS (CONFIG_CMD_DFL | CFG_CMD_PCI | \ - CFG_CMD_ELF | CFG_CMD_PING | CFG_CMD_I2C) - #elif defined(CONFIG_TSEC_ENET) - #define CONFIG_COMMANDS (CONFIG_CMD_DFL | CFG_CMD_PING | \ - CFG_CMD_ELF | CFG_CMD_MII | CFG_CMD_I2C) - #elif defined(CONFIG_ETHER_ON_FCC) - #define CONFIG_COMMANDS (CONFIG_CMD_DFL | CFG_CMD_MII | \ - CFG_CMD_ELF | CFG_CMD_PING | CFG_CMD_I2C) - #endif + #define CONFIG_CMD_ELF +#endif + +#if defined(CONFIG_PCI) + #define CONFIG_CMD_PCI #endif -#include + +#if defined(CONFIG_TSEC_ENET) || defined(CONFIG_ETHER_ON_FCC) + #define CONFIG_CMD_MII +#endif + #undef CONFIG_WATCHDOG /* watchdog disabled */ @@ -328,7 +341,7 @@ */ #define CFG_LONGHELP /* undef to save memory */ #define CFG_PROMPT "GPPP=> " /* Monitor Command Prompt */ -#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#if defined(CONFIG_CMD_KGDB) #define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ #else #define CFG_CBSIZE 256 /* Console I/O Buffer Size */ @@ -346,13 +359,6 @@ */ #define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ -/* Cache Configuration */ -#define CFG_DCACHE_SIZE 32768 -#define CFG_CACHELINE_SIZE 32 -#if (CONFIG_COMMANDS & CFG_CMD_KGDB) -#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -#endif - /* * Internal Definitions * @@ -361,27 +367,28 @@ #define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ #define BOOTFLAG_WARM 0x02 /* Software reboot */ -#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#if defined(CONFIG_CMD_KGDB) #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ #endif /*Note: change below for your network setting!!! */ #if defined(CONFIG_TSEC_ENET) || defined(CONFIG_ETHER_ON_FCC) -#define CONFIG_ETHADDR 00:e0:0c:07:9b:8a +#define CONFIG_HAS_ETH0 +#define CONFIG_ETHADDR 00:e0:0c:07:9b:8a #define CONFIG_HAS_ETH1 -#define CONFIG_ETH1ADDR 00:e0:0c:07:9b:8b +#define CONFIG_ETH1ADDR 00:e0:0c:07:9b:8b #define CONFIG_HAS_ETH2 -#define CONFIG_ETH2ADDR 00:e0:0c:07:9b:8c +#define CONFIG_ETH2ADDR 00:e0:0c:07:9b:8c #endif -#define CONFIG_SERVERIP 192.168.85.1 -#define CONFIG_IPADDR 192.168.85.60 +#define CONFIG_SERVERIP 192.168.85.1 +#define CONFIG_IPADDR 192.168.85.60 #define CONFIG_GATEWAYIP 192.168.85.1 #define CONFIG_NETMASK 255.255.255.0 -#define CONFIG_HOSTNAME STX_GP3 -#define CONFIG_ROOTPATH /gppproot -#define CONFIG_BOOTFILE uImage +#define CONFIG_HOSTNAME STX_GP3 +#define CONFIG_ROOTPATH /gppproot +#define CONFIG_BOOTFILE uImage #define CONFIG_LOADADDR 0x1000000 #endif /* __CONFIG_H */