X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2Fsocrates.h;h=96410413a0f4f81fce7d0ba69ff7029e6e7860b4;hb=4b142febff71eabdb7ddbb125c7b583b24ddc434;hp=499f41ceb1a5c701654a441e92cb2794667d55f3;hpb=59abd15b43cab7a4d19de4ba0943837d9555f7ba;p=platform%2Fkernel%2Fu-boot.git diff --git a/include/configs/socrates.h b/include/configs/socrates.h index 499f41c..9641041 100644 --- a/include/configs/socrates.h +++ b/include/configs/socrates.h @@ -33,6 +33,11 @@ #ifndef __CONFIG_H #define __CONFIG_H +/* new uImage format support */ +#define CONFIG_FIT 1 +#define CONFIG_OF_LIBFDT 1 +#define CONFIG_FIT_VERBOSE 1 /* enable fit_format_{error,warning}() */ + /* High Level Configuration Options */ #define CONFIG_BOOKE 1 /* BOOKE */ #define CONFIG_E500 1 /* BOOKE e500 family */ @@ -45,6 +50,7 @@ #define CONFIG_TSEC_ENET /* tsec ethernet support */ #define CONFIG_MISC_INIT_R 1 /* Call misc_init_r */ +#define CONFIG_BOARD_EARLY_INIT_R 1 /* Call board_early_init_r */ #define CONFIG_FSL_LAW 1 /* Use common FSL init code */ @@ -76,118 +82,160 @@ */ #define CONFIG_L2_CACHE /* toggle L2 cache */ #define CONFIG_BTB /* toggle branch predition */ -#define CONFIG_ADDR_STREAMING /* toggle addr streaming */ -#define CFG_INIT_DBCR DBCR_IDM /* Enable Debug Exceptions */ +#define CONFIG_SYS_INIT_DBCR DBCR_IDM /* Enable Debug Exceptions */ -#undef CFG_DRAM_TEST /* memory test, takes time */ -#define CFG_MEMTEST_START 0x00000000 -#define CFG_MEMTEST_END 0x10000000 +#undef CONFIG_SYS_DRAM_TEST /* memory test, takes time */ +#define CONFIG_SYS_MEMTEST_START 0x00400000 +#define CONFIG_SYS_MEMTEST_END 0x00C00000 /* * Base addresses -- Note these are effective addresses where the * actual resources get mapped (not physical addresses) */ -#define CFG_CCSRBAR_DEFAULT 0xFF700000 /* CCSRBAR Default */ -#define CFG_CCSRBAR 0xE0000000 /* relocated CCSRBAR */ -#define CFG_CCSRBAR_PHYS CFG_CCSRBAR /* physical addr of CCSRBAR */ -#define CFG_IMMR CFG_CCSRBAR /* PQII uses CFG_IMMR */ +#define CONFIG_SYS_CCSRBAR_DEFAULT 0xFF700000 /* CCSRBAR Default */ +#define CONFIG_SYS_CCSRBAR 0xE0000000 /* relocated CCSRBAR */ +#define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR /* physical addr of CCSRBAR */ +#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */ -/* - * DDR Setup - */ -#define CFG_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory */ -#define CFG_SDRAM_BASE CFG_DDR_SDRAM_BASE +/* DDR Setup */ +#define CONFIG_FSL_DDR2 +#undef CONFIG_FSL_DDR_INTERACTIVE +#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */ +#define CONFIG_DDR_SPD + +#undef CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */ +#define CONFIG_MEM_INIT_VALUE 0xDeadBeef + +#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 +#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE +#define CONFIG_VERY_BIG_RAM + +#define CONFIG_NUM_DDR_CONTROLLERS 1 +#define CONFIG_DIMM_SLOTS_PER_CTLR 1 +#define CONFIG_CHIP_SELECTS_PER_CTRL 2 + +/* I2C addresses of SPD EEPROMs */ +#define SPD_EEPROM_ADDRESS 0x50 /* CTLR 0 DIMM 0 */ #define CONFIG_DDR_DEFAULT_CL 30 /* CAS latency 3 */ /* Hardcoded values, to use instead of SPD */ -#define CFG_DDR_CS0_BNDS 0x0000000f -#define CFG_DDR_CS0_CONFIG 0x80010102 -#define CFG_DDR_TIMING_0 0x00260802 -#define CFG_DDR_TIMING_1 0x3935D322 -#define CFG_DDR_TIMING_2 0x14904CC8 -#define CFG_DDR_MODE 0x00480432 -#define CFG_DDR_INTERVAL 0x030C0100 -#define CFG_DDR_CONFIG_2 0x04400000 -#define CFG_DDR_CONFIG 0xC3008000 -#define CFG_DDR_CLK_CONTROL 0x03800000 -#define CFG_SDRAM_SIZE 256 /* in Megs */ - -#define CONFIG_SPD_EEPROM 1 /* Use SPD EEPROM for DDR setup*/ -#define SPD_EEPROM_ADDRESS 0x50 /* DDR DIMM */ -#define MPC85xx_DDR_SDRAM_CLK_CNTL /* 85xx has clock control reg */ +#define CONFIG_SYS_DDR_CS0_BNDS 0x0000000f +#define CONFIG_SYS_DDR_CS0_CONFIG 0x80010102 +#define CONFIG_SYS_DDR_TIMING_0 0x00260802 +#define CONFIG_SYS_DDR_TIMING_1 0x3935D322 +#define CONFIG_SYS_DDR_TIMING_2 0x14904CC8 +#define CONFIG_SYS_DDR_MODE 0x00480432 +#define CONFIG_SYS_DDR_INTERVAL 0x030C0100 +#define CONFIG_SYS_DDR_CONFIG_2 0x04400000 +#define CONFIG_SYS_DDR_CONFIG 0xC3008000 +#define CONFIG_SYS_DDR_CLK_CONTROL 0x03800000 +#define CONFIG_SYS_SDRAM_SIZE 256 /* in Megs */ /* - * Flash on the Local Bus - */ -/* * Flash on the LocalBus */ -#define CFG_LBC_CACHE_BASE 0xf0000000 /* Localbus cacheable */ +#define CONFIG_SYS_LBC_CACHE_BASE 0xf0000000 /* Localbus cacheable */ + +#define CONFIG_SYS_FLASH0 0xFE000000 +#define CONFIG_SYS_FLASH1 0xFC000000 +#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH1, CONFIG_SYS_FLASH0 } -#define CFG_FLASH0 0xFE000000 -#define CFG_FLASH1 0xFC000000 -#define CFG_FLASH_BANKS_LIST { CFG_FLASH1, CFG_FLASH0 } +#define CONFIG_SYS_LBC_FLASH_BASE CONFIG_SYS_FLASH1 /* Localbus flash start */ +#define CONFIG_SYS_FLASH_BASE CONFIG_SYS_LBC_FLASH_BASE /* start of FLASH */ -#define CFG_LBC_FLASH_BASE CFG_FLASH1 /* Localbus flash start */ -#define CFG_FLASH_BASE CFG_LBC_FLASH_BASE /* start of FLASH */ +#define CONFIG_SYS_BR0_PRELIM 0xfe001001 /* port size 16bit */ +#define CONFIG_SYS_OR0_PRELIM 0xfe000030 /* 32MB Flash */ +#define CONFIG_SYS_BR1_PRELIM 0xfc001001 /* port size 16bit */ +#define CONFIG_SYS_OR1_PRELIM 0xfe000030 /* 32MB Flash */ -#define CFG_BR0_PRELIM 0xfe001001 /* port size 16bit */ -#define CFG_OR0_PRELIM 0xfe000ff7 /* 32MB Flash */ -#define CFG_BR1_PRELIM 0xfc001001 /* port size 16bit */ -#define CFG_OR1_PRELIM 0xfe000ff7 /* 32MB Flash */ +#define CONFIG_SYS_FLASH_CFI /* flash is CFI compat. */ +#define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver*/ -#define CFG_FLASH_CFI /* flash is CFI compat. */ -#define CFG_FLASH_CFI_DRIVER /* Use common CFI driver*/ -#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector */ +#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */ +#define CONFIG_SYS_MAX_FLASH_SECT 256 /* sectors per device */ +#undef CONFIG_SYS_FLASH_CHECKSUM +#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ +#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ -#define CFG_MAX_FLASH_BANKS 2 /* number of banks */ -#define CFG_MAX_FLASH_SECT 256 /* sectors per device */ -#undef CFG_FLASH_CHECKSUM -#define CFG_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ -#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ +#define CONFIG_SYS_MONITOR_BASE TEXT_BASE /* start of monitor */ -#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */ +#define CONFIG_SYS_LBC_LCRR 0x00030004 /* LB clock ratio reg */ +#define CONFIG_SYS_LBC_LBCR 0x00000000 /* LB config reg */ +#define CONFIG_SYS_LBC_LSRT 0x20000000 /* LB sdram refresh timer */ +#define CONFIG_SYS_LBC_MRTPR 0x20000000 /* LB refresh timer presc.*/ -#define CFG_LBC_LCRR 0x00030008 /* LB clock ratio reg */ -#define CFG_LBC_LBCR 0x00000000 /* LB config reg */ -#define CFG_LBC_LSRT 0x20000000 /* LB sdram refresh timer */ -#define CFG_LBC_MRTPR 0x20000000 /* LB refresh timer presc.*/ +#define CONFIG_SYS_INIT_RAM_LOCK 1 +#define CONFIG_SYS_INIT_RAM_ADDR 0xe4010000 /* Initial RAM address */ +#define CONFIG_SYS_INIT_RAM_END 0x4000 /* End used area in RAM */ -#define CONFIG_L1_INIT_RAM -#define CFG_INIT_RAM_LOCK 1 -#define CFG_INIT_RAM_ADDR 0xe4010000 /* Initial RAM address */ -#define CFG_INIT_RAM_END 0x4000 /* End used area in RAM */ +#define CONFIG_SYS_GBL_DATA_SIZE 128 /* num bytes initial data*/ +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET -#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data*/ -#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) -#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET +#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256kB for Mon */ +#define CONFIG_SYS_MALLOC_LEN (4 << 20) /* Reserve 4 MB for malloc */ -#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256kB for Mon*/ -#define CFG_MALLOC_LEN (128 * 1024) /* Reserved for malloc */ +/* FPGA and NAND */ +#define CONFIG_SYS_FPGA_BASE 0xc0000000 +#define CONFIG_SYS_FPGA_SIZE 0x00100000 /* 1 MB */ +#define CONFIG_SYS_HMI_BASE 0xc0010000 +#define CONFIG_SYS_BR3_PRELIM 0xc0001881 /* UPMA, 32-bit */ +#define CONFIG_SYS_OR3_PRELIM 0xfff00000 /* 1 MB */ + +#define CONFIG_SYS_NAND_BASE (CONFIG_SYS_FPGA_BASE + 0x70) +#define CONFIG_SYS_MAX_NAND_DEVICE 1 +#define CONFIG_CMD_NAND + +/* LIME GDC */ +#define CONFIG_SYS_LIME_BASE 0xc8000000 +#define CONFIG_SYS_LIME_SIZE 0x04000000 /* 64 MB */ +#define CONFIG_SYS_BR2_PRELIM 0xc80018a1 /* UPMB, 32-bit */ +#define CONFIG_SYS_OR2_PRELIM 0xfc000000 /* 64 MB */ + +#define CONFIG_VIDEO +#define CONFIG_VIDEO_MB862xx +#define CONFIG_VIDEO_MB862xx_ACCEL +#define CONFIG_CFB_CONSOLE +#define CONFIG_VIDEO_LOGO +#define CONFIG_VIDEO_BMP_LOGO +#define CONFIG_CONSOLE_EXTRA_INFO +#define VIDEO_FB_16BPP_PIXEL_SWAP +#define VIDEO_FB_16BPP_WORD_SWAP +#define CONFIG_VGA_AS_SINGLE_DEVICE +#define CONFIG_SYS_CONSOLE_IS_IN_ENV +#define CONFIG_VIDEO_SW_CURSOR +#define CONFIG_SPLASH_SCREEN +#define CONFIG_VIDEO_BMP_GZIP +#define CONFIG_SYS_VIDEO_LOGO_MAX_SIZE (2 << 20) /* decompressed img */ + +/* SDRAM Clock frequency, 100MHz (0x0000) or 133MHz (0x10000) */ +#define CONFIG_SYS_MB862xx_CCF 0x10000 +/* SDRAM parameter */ +#define CONFIG_SYS_MB862xx_MMR 0x4157BA63 /* Serial Port */ #define CONFIG_CONS_INDEX 1 #undef CONFIG_SERIAL_SOFTWARE_FIFO -#define CFG_NS16550 -#define CFG_NS16550_SERIAL -#define CFG_NS16550_REG_SIZE 1 -#define CFG_NS16550_CLK get_bus_freq(0) +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK get_bus_freq(0) -#define CFG_NS16550_COM1 (CFG_CCSRBAR+0x4500) -#define CFG_NS16550_COM2 (CFG_CCSRBAR+0x4600) +#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500) +#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600) #define CONFIG_BAUDRATE 115200 -#define CFG_BAUDRATE_TABLE \ +#define CONFIG_SYS_BAUDRATE_TABLE \ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200} #define CONFIG_CMDLINE_EDITING 1 /* add command line history */ -#define CFG_HUSH_PARSER 1 /* Use the HUSH parser */ -#ifdef CFG_HUSH_PARSER -#define CFG_PROMPT_HUSH_PS2 "> " +#define CONFIG_SYS_HUSH_PARSER 1 /* Use the HUSH parser */ +#ifdef CONFIG_SYS_HUSH_PARSER +#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " #endif @@ -197,39 +245,43 @@ #define CONFIG_FSL_I2C /* Use FSL common I2C driver */ #define CONFIG_HARD_I2C /* I2C with hardware support */ #undef CONFIG_SOFT_I2C /* I2C bit-banged */ -#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CFG_I2C_SLAVE 0x7F -#define CFG_I2C_NOPROBES {0x48} /* Don't probe these addrs */ -#define CFG_I2C_OFFSET 0x3000 +#define CONFIG_SYS_I2C_SPEED 102124 /* I2C speed and slave address */ +#define CONFIG_SYS_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C_OFFSET 0x3000 + +#define CONFIG_I2C_MULTI_BUS +#define CONFIG_SYS_I2C2_OFFSET 0x3100 /* I2C RTC */ #define CONFIG_RTC_RX8025 /* Use Epson rx8025 rtc via i2c */ -#define CFG_I2C_RTC_ADDR 0x32 /* at address 0x32 */ +#define CONFIG_SYS_I2C_RTC_ADDR 0x32 /* at address 0x32 */ + +/* I2C W83782G HW-Monitoring IC */ +#define CONFIG_SYS_I2C_W83782G_ADDR 0x28 /* W83782G address */ /* I2C temp sensor */ /* Socrates uses Maxim's DS75, which is compatible with LM75 */ #define CONFIG_DTT_LM75 1 #define CONFIG_DTT_SENSORS {4} /* Sensor addresses */ -#define CFG_DTT_MAX_TEMP 125 -#define CFG_DTT_LOW_TEMP -55 -#define CFG_DTT_HYSTERESIS 3 -#define CFG_EEPROM_PAGE_WRITE_ENABLE /* necessary for the LM75 chip */ -#define CFG_EEPROM_PAGE_WRITE_BITS 4 +#define CONFIG_SYS_DTT_MAX_TEMP 125 +#define CONFIG_SYS_DTT_LOW_TEMP -55 +#define CONFIG_SYS_DTT_HYSTERESIS 3 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4 /* * General PCI * Memory space is mapped 1-1. */ -#define CFG_PCI_PHYS 0x80000000 /* 1G PCI TLB */ +#define CONFIG_SYS_PCI_PHYS 0x80000000 /* 1G PCI TLB */ /* PCI is clocked by the external source at 33 MHz */ #define CONFIG_PCI_CLK_FREQ 33000000 -#define CFG_PCI1_MEM_BASE 0x80000000 -#define CFG_PCI1_MEM_PHYS CFG_PCI1_MEM_BASE -#define CFG_PCI1_MEM_SIZE 0x20000000 /* 512M */ -#define CFG_PCI1_IO_BASE 0xE2000000 -#define CFG_PCI1_IO_PHYS CFG_PCI1_IO_BASE -#define CFG_PCI1_IO_SIZE 0x01000000 /* 16M */ +#define CONFIG_SYS_PCI1_MEM_BASE 0x80000000 +#define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BASE +#define CONFIG_SYS_PCI1_MEM_SIZE 0x20000000 /* 512M */ +#define CONFIG_SYS_PCI1_IO_BASE 0xE2000000 +#define CONFIG_SYS_PCI1_IO_PHYS CONFIG_SYS_PCI1_IO_BASE +#define CONFIG_SYS_PCI1_IO_SIZE 0x01000000 /* 16M */ #if defined(CONFIG_PCI) #define CONFIG_PCI_PNP /* do pci plug-and-play */ @@ -263,15 +315,15 @@ /* * Environment */ -#define CFG_ENV_IS_IN_FLASH 1 -#define CFG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */ -#define CFG_ENV_ADDR (CFG_MONITOR_BASE - CFG_ENV_SECT_SIZE) -#define CFG_ENV_SIZE 0x4000 -#define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR-CFG_ENV_SECT_SIZE) -#define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE) +#define CONFIG_ENV_IS_IN_FLASH 1 +#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */ +#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE) +#define CONFIG_ENV_SIZE 0x4000 +#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR-CONFIG_ENV_SECT_SIZE) +#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ +#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ #define CONFIG_TIMESTAMP /* Print image info with ts */ @@ -295,44 +347,45 @@ #define CONFIG_CMD_DTT #undef CONFIG_CMD_EEPROM #define CONFIG_CMD_I2C +#define CONFIG_CMD_SDRAM #define CONFIG_CMD_MII #define CONFIG_CMD_NFS #define CONFIG_CMD_PING #define CONFIG_CMD_SNTP #define CONFIG_CMD_USB - +#define CONFIG_CMD_EXT2 /* EXT2 Support */ +#define CONFIG_CMD_BMP #if defined(CONFIG_PCI) #define CONFIG_CMD_PCI #endif - #undef CONFIG_WATCHDOG /* watchdog disabled */ /* * Miscellaneous configurable options */ -#define CFG_LONGHELP /* undef to save memory */ -#define CFG_LOAD_ADDR 0x2000000 /* default load address */ -#define CFG_PROMPT "=> " /* Monitor Command Prompt */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ +#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ #if defined(CONFIG_CMD_KGDB) - #define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ + #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ #else - #define CFG_CBSIZE 256 /* Console I/O Buffer Size */ + #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ #endif -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buf Size */ -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ -#define CFG_HZ 1000 /* decrementer freq: 1ms ticks */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buf Size */ +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ +#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */ /* * For booting Linux, the board info and command line data * have to be in the first 8 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization. */ -#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ +#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ /* * Internal Definitions @@ -350,50 +403,69 @@ #define CONFIG_LOADADDR 200000 /* default addr for tftp & bootm*/ -#define CONFIG_BOOTDELAY 5 /* -1 disables auto-boot */ +#define CONFIG_BOOTDELAY 1 /* -1 disables auto-boot */ #define CONFIG_PREBOOT "echo;" \ - "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \ + "echo Welcome on the ABB Socrates Board;" \ "echo" #undef CONFIG_BOOTARGS /* the boot command will set bootargs */ #define CONFIG_EXTRA_ENV_SETTINGS \ - "bootfile=$hostname/uImage\0" \ "netdev=eth0\0" \ "consdev=ttyS0\0" \ - "hostname=socrates\0" \ + "uboot_file=/home/tftp/syscon3/u-boot.bin\0" \ + "bootfile=/home/tftp/syscon3/uImage\0" \ + "fdt_file=/home/tftp/syscon3/socrates.dtb\0" \ + "initrd_file=/home/tftp/syscon3/uinitrd.gz\0" \ + "uboot_addr=FFFA0000\0" \ + "kernel_addr=FE000000\0" \ + "fdt_addr=FE1E0000\0" \ + "ramdisk_addr=FE200000\0" \ + "fdt_addr_r=B00000\0" \ + "kernel_addr_r=200000\0" \ + "ramdisk_addr_r=400000\0" \ + "rootpath=/opt/eldk/ppc_85xxDP\0" \ + "ramargs=setenv bootargs root=/dev/ram rw\0" \ "nfsargs=setenv bootargs root=/dev/nfs rw " \ "nfsroot=$serverip:$rootpath\0" \ - "ramargs=setenv bootargs root=/dev/ram rw\0" \ + "addcons=setenv bootargs $bootargs " \ + "console=$consdev,$baudrate\0" \ "addip=setenv bootargs $bootargs " \ "ip=$ipaddr:$serverip:$gatewayip:$netmask" \ ":$hostname:$netdev:off panic=1\0" \ - "addcons=setenv bootargs $bootargs " \ - "console=$consdev,$baudrate\0" \ - "flash_self=run ramargs addip addcons;" \ + "boot_nor=run ramargs addcons;" \ "bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0" \ - "flash_nfs=run nfsargs addip addcons;" \ - "bootm ${kernel_addr} - ${fdt_addr}\0" \ "net_nfs=tftp ${kernel_addr_r} ${bootfile}; " \ "tftp ${fdt_addr_r} ${fdt_file}; " \ "run nfsargs addip addcons;" \ "bootm ${kernel_addr_r} - ${fdt_addr_r}\0" \ - "fdt_file=$hostname/socrates.dtb\0" \ - "fdt_addr_r=B00000\0" \ - "fdt_addr=FC1E0000\0" \ - "rootpath=/opt/eldk/ppc_85xxDP\0" \ - "kernel_addr=FC000000\0" \ - "kernel_addr_r=200000\0" \ - "ramdisk_addr=FC200000\0" \ - "ramdisk_addr_r=400000\0" \ - "load=tftp 100000 $hostname/u-boot.bin\0" \ - "update=protect off fffc0000 ffffffff;era fffc0000 ffffffff;" \ - "cp.b 100000 fffc0000 40000;" \ + "update_uboot=tftp 100000 ${uboot_file};" \ + "protect off fffa0000 ffffffff;" \ + "era fffa0000 ffffffff;" \ + "cp.b 100000 fffa0000 ${filesize};" \ + "setenv filesize;saveenv\0" \ + "update_kernel=tftp 100000 ${bootfile};" \ + "era fe000000 fe1dffff;" \ + "cp.b 100000 fe000000 ${filesize};" \ "setenv filesize;saveenv\0" \ - "upd=run load update\0" \ + "update_fdt=tftp 100000 ${fdt_file};" \ + "era fe1e0000 fe1fffff;" \ + "cp.b 100000 fe1e0000 ${filesize};" \ + "setenv filesize;saveenv\0" \ + "update_initrd=tftp 100000 ${initrd_file};" \ + "era fe200000 fe9fffff;" \ + "cp.b 100000 fe200000 ${filesize};" \ + "setenv filesize;saveenv\0" \ + "clean_data=era fea00000 fff5ffff\0" \ + "usbargs=setenv bootargs root=/dev/sda1 rw\0" \ + "load_usb=usb start;" \ + "ext2load usb 0:1 ${kernel_addr_r} /boot/uImage\0" \ + "boot_usb=run load_usb usbargs addcons;" \ + "bootm ${kernel_addr_r} - ${fdt_addr};" \ + "bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0" \ "" -#define CONFIG_BOOTCOMMAND "run flash_self" +#define CONFIG_BOOTCOMMAND "run boot_nor" /* pass open firmware flat tree */ #define CONFIG_OF_LIBFDT 1 @@ -403,14 +475,11 @@ #define CONFIG_USB_OHCI_NEW 1 #define CONFIG_PCI_OHCI 1 #define CONFIG_PCI_OHCI_DEVNO 3 /* Number in PCI list */ -#define CFG_USB_OHCI_MAX_ROOT_PORTS 15 -#define CFG_USB_OHCI_SLOT_NAME "ohci_pci" -#define CFG_OHCI_SWAP_REG_ACCESS 1 +#define CONFIG_PCI_EHCI_DEVNO (CONFIG_PCI_OHCI_DEVNO / 2) +#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 15 +#define CONFIG_SYS_USB_OHCI_SLOT_NAME "ohci_pci" +#define CONFIG_SYS_OHCI_SWAP_REG_ACCESS 1 #define CONFIG_DOS_PARTITION 1 #define CONFIG_USB_STORAGE 1 -/* FPGA and NAND */ -#define CFG_FPGA_BASE 0xc0000000 -#define CFG_BR3_PRELIM 0xc0001881 /* UPMA, 32-bit */ -#define CFG_OR3_PRELIM 0xfff00000 /* 1 MB */ #endif /* __CONFIG_H */