X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2Fsocfpga_vining_fpga.h;h=232536a763d61919d2bdf2f123ea2159ceeb2b9d;hb=37304aaf60bf92a5dc3ef222ba520698bd862a44;hp=c5555e699067fb8aa38dbd3bce640dc7616d49be;hpb=06572f0301c18e63b887efc91803bb9467e55dbe;p=platform%2Fkernel%2Fu-boot.git

diff --git a/include/configs/socfpga_vining_fpga.h b/include/configs/socfpga_vining_fpga.h
index c5555e6..232536a 100644
--- a/include/configs/socfpga_vining_fpga.h
+++ b/include/configs/socfpga_vining_fpga.h
@@ -1,74 +1,28 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
 /*
  * Copyright (C) 2015 Marek Vasut <marex@denx.de>
- *
- * SPDX-License-Identifier:	GPL-2.0+
  */
 #ifndef __CONFIG_SAMTEC_VINING_FPGA_H__
 #define __CONFIG_SAMTEC_VINING_FPGA_H__
 
 #include <asm/arch/base_addr_ac5.h>
 
-/* U-Boot Commands */
-#define CONFIG_SYS_NO_FLASH
-#define CONFIG_DOS_PARTITION
-#define CONFIG_FAT_WRITE
-#define CONFIG_HW_WATCHDOG
-
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_LED
-
 /* Memory configurations */
 #define PHYS_SDRAM_1_SIZE		0x40000000	/* 1GiB on VINING_FPGA */
 
 /* Booting Linux */
 #define CONFIG_BOOTFILE		"openwrt-socfpga-socfpga_cyclone5_vining_fpga-fit-uImage.itb"
-#define CONFIG_BOOTARGS		"console=ttyS0," __stringify(CONFIG_BAUDRATE)
 #define CONFIG_BOOTCOMMAND	"run selboot"
 #define CONFIG_LOADADDR		0x01000000
 #define CONFIG_SYS_LOAD_ADDR	CONFIG_LOADADDR
 
-/* I2C EEPROM */
-#ifdef CONFIG_CMD_EEPROM
-#define CONFIG_SYS_I2C_EEPROM_ADDR		0x50
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN		1
-#define CONFIG_SYS_I2C_EEPROM_BUS		0
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	3
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	70
-#endif
-
-/*
- * Status LEDs:
- *   0 ... Top Green
- *   1 ... Top Red
- *   2 ... Bottom Green
- *   3 ... Bottom Red
- */
-#define CONFIG_STATUS_LED
-#define CONFIG_GPIO_LED
-#define CONFIG_BOARD_SPECIFIC_LED
-#define STATUS_LED_BIT		48
-#define STATUS_LED_STATE	STATUS_LED_OFF
-#define STATUS_LED_PERIOD	(CONFIG_SYS_HZ / 2)
-#define STATUS_LED_BIT1		53
-#define STATUS_LED_STATE1	STATUS_LED_OFF
-#define STATUS_LED_PERIOD1	(CONFIG_SYS_HZ / 2)
-#define STATUS_LED_BIT2		54
-#define STATUS_LED_STATE2	STATUS_LED_OFF
-#define STATUS_LED_PERIOD2	(CONFIG_SYS_HZ / 2)
-#define STATUS_LED_BIT3		65
-#define STATUS_LED_STATE3	STATUS_LED_OFF
-#define STATUS_LED_PERIOD3	(CONFIG_SYS_HZ / 2)
-
 /* Ethernet on SoC (EMAC) */
 #if defined(CONFIG_CMD_NET)
 #define CONFIG_BOOTP_SEND_HOSTNAME
-/* PHY */
-#define CONFIG_PHY_MICREL
-#define CONFIG_PHY_MICREL_KSZ9021
 #endif
 
 /* Extra Environment */
-#define CONFIG_HOSTNAME			socfpga_vining_fpga
+#define CONFIG_HOSTNAME			"socfpga_vining_fpga"
 
 /*
  * Active LOW GPIO buttons:
@@ -79,16 +33,6 @@
  *  if button B is not pressed, boot normal Linux system immediatelly
  *  if button B is pressed, wait $bootdelay and boot recovery system
  */
-#define CONFIG_PREBOOT						\
-	"setenv hostname vining-${unit_serial} ; "		\
-	"setenv PS1 \"${unit_ident} (${unit_serial}) => \" ; "	\
-	"if gpio input 78 ; then "			\
-		"setenv bootdelay 10 ; "		\
-		"setenv boottype rcvr ; "		\
-	"else "						\
-		"setenv bootdelay 5 ; "			\
-		"setenv boottype norm ; "		\
-	"fi"
 
 #define CONFIG_EXTRA_ENV_SETTINGS \
 	"verify=n\0" \
@@ -191,20 +135,8 @@
 			"run ubi_ubi ; "				\
 		"else echo \"Unsupported boot mode: \"${bootmode} ; "	\
 		"fi\0"							\
+		"socfpga_legacy_reset_compat=1\0"
 
-#define CONFIG_CMD_UBIFS
-#define CONFIG_RBTREE
-#define CONFIG_LZO
-#define MTDPARTS_DEFAULT			\
-	"mtdparts=ff705000.spi.0:"		\
-		"1m(u-boot),"			\
-		"64k(env1),"			\
-		"64k(env2),"			\
-		"256k(samtec1),"		\
-		"256k(samtec2),"		\
-		"-(rcvrfs);"	/* Recovery */	\
-
-#define CONFIG_ENV_IS_IN_SPI_FLASH
 #define CONFIG_SYS_REDUNDAND_ENVIRONMENT
 #define CONFIG_ENV_SIZE_REDUND		CONFIG_ENV_SIZE
 #define CONFIG_ENV_SECT_SIZE		(64 * 1024)
@@ -212,9 +144,6 @@
 #define CONFIG_ENV_OFFSET_REDUND	\
 	(CONFIG_ENV_OFFSET + CONFIG_ENV_SECT_SIZE)
 
-#define CONFIG_MISC_INIT_R
-#define CONFIG_BOARD_LATE_INIT
-
 /* Support changing the prompt string */
 #define CONFIG_CMDLINE_PS_SUPPORT