X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2Fsocfpga_sr1500.h;h=3a8ccc3021694d3f5e2cc0871694a8f6ad0edfaf;hb=e4b91f085d4259f187052ff724c80af38fc11b18;hp=424cada15704593d25b92d33830a487174b6f761;hpb=a5d67547dd9c7a527dfda1967010e703a22441ff;p=platform%2Fkernel%2Fu-boot.git

diff --git a/include/configs/socfpga_sr1500.h b/include/configs/socfpga_sr1500.h
index 424cada..3a8ccc3 100644
--- a/include/configs/socfpga_sr1500.h
+++ b/include/configs/socfpga_sr1500.h
@@ -1,72 +1,30 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
 /*
  * Copyright (C) 2015 Stefan Roese <sr@denx.de>
- *
- * SPDX-License-Identifier:	GPL-2.0+
  */
 #ifndef __CONFIG_SOCFPGA_SR1500_H__
 #define __CONFIG_SOCFPGA_SR1500_H__
 
 #include <asm/arch/base_addr_ac5.h>
 
-#define CONFIG_SYS_NO_FLASH
-#define CONFIG_DOS_PARTITION
-#define CONFIG_FAT_WRITE
-
-#define CONFIG_HW_WATCHDOG
-
 /* Memory configurations */
 #define PHYS_SDRAM_1_SIZE		0x40000000	/* 1GiB on SR1500 */
 
 /* Booting Linux */
-#define CONFIG_BOOTFILE		"uImage"
-#define CONFIG_BOOTARGS		"console=ttyS0," __stringify(CONFIG_BAUDRATE)
-#define CONFIG_BOOTCOMMAND	"run mmcload; run mmcboot"
 #define CONFIG_LOADADDR		0x01000000
 #define CONFIG_SYS_LOAD_ADDR	CONFIG_LOADADDR
 
 /* Ethernet on SoC (EMAC) */
 #define CONFIG_PHY_INTERFACE_MODE	PHY_INTERFACE_MODE_RGMII
 /* The PHY is autodetected, so no MII PHY address is needed here */
-#define CONFIG_PHY_MARVELL
 #define PHY_ANEG_TIMEOUT	8000
 
-#define CONFIG_EXTRA_ENV_SETTINGS \
-	"verify=n\0" \
-	"loadaddr=" __stringify(CONFIG_SYS_LOAD_ADDR) "\0" \
-	"ramboot=setenv bootargs " CONFIG_BOOTARGS ";" \
-		"bootm ${loadaddr} - ${fdt_addr}\0" \
-	"bootimage=zImage\0" \
-	"fdt_addr=100\0" \
-	"fdtimage=socfpga.dtb\0" \
-		"fsloadcmd=ext2load\0" \
-	"bootm ${loadaddr} - ${fdt_addr}\0" \
-	"mmcroot=/dev/mmcblk0p2\0" \
-	"mmcboot=setenv bootargs " CONFIG_BOOTARGS \
-		" root=${mmcroot} rw rootwait;" \
-		"bootz ${loadaddr} - ${fdt_addr}\0" \
-	"mmcload=mmc rescan;" \
-		"load mmc 0:1 ${loadaddr} ${bootimage};" \
-		"load mmc 0:1 ${fdt_addr} ${fdtimage}\0" \
-	"qspiload=sf probe && mtdparts default && run ubiload\0" \
-	"qspiboot=setenv bootargs " CONFIG_BOOTARGS \
-		" ubi.mtd=1,64 root=ubi0:rootfs rw rootfstype=ubifs;"\
-		"bootz ${loadaddr} - ${fdt_addr}\0" \
-	"ubiload=ubi part UBI && ubifsmount ubi0 && " \
-		"ubifsload ${loadaddr} /boot/${bootimage} && " \
-		"ubifsload ${fdt_addr} /boot/${fdtimage}\0"
-
-/* Environment */
-#define CONFIG_ENV_IS_IN_SPI_FLASH
-
 /* Enable SPI NOR flash reset, needed for SPI booting */
 #define CONFIG_SPI_N25Q256A_RESET
 
 /*
  * Bootcounter
  */
-#define CONFIG_BOOTCOUNT_LIMIT
-/* last 2 lwords in OCRAM */
-#define CONFIG_SYS_BOOTCOUNT_ADDR	0xfffffff8
 #define CONFIG_SYS_BOOTCOUNT_BE
 
 /* Environment setting for SPI flash */
@@ -75,20 +33,6 @@
 #define CONFIG_ENV_SIZE		(16 * 1024)
 #define CONFIG_ENV_OFFSET	0x000e0000
 #define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SECT_SIZE)
-#define CONFIG_ENV_SPI_BUS	0
-#define CONFIG_ENV_SPI_CS	0
-#define CONFIG_ENV_SPI_MODE	SPI_MODE_3
-#define CONFIG_ENV_SPI_MAX_HZ	100000000	/* Use max of 100MHz */
-#define CONFIG_SF_DEFAULT_SPEED	100000000
-
-/*
- * The QSPI NOR flash layout on SR1500:
- *
- * 0000.0000 - 0003.ffff: SPL (4 times)
- * 0004.0000 - 000d.ffff: U-Boot
- * 000e.0000 - 000e.ffff: env1
- * 000f.0000 - 000f.ffff: env2
- */
 
 /* The rest of the configuration is shared */
 #include <configs/socfpga_common.h>